Search Documents

By Edward D. Thimons

Because of the high number of accidental methane gas ignitions in metal and nonmetal mines, the Bureau of Mines searched for a simple guideline that would allow mine personnel to evaluate the methane hazard in a given mine. Air samples were collected by the Bureau in 53 metal and nonmetal mines and analyzed for trace evidence of methane gas. Samples were collected in the returns and at the working faces. Those mines classified as gassy by the Mine Safety and Health Administration had a significantly higher average methane concentration than those classified as nongassy. Of the 9 gassy mines sampled, 7 had methane concentrations above 100 ppm, whereas only 1 of the 44 nongassy mines had a concentration above 100 ppm. The 100-ppm concentration may be used as a simple and convenient guideline for forecasting the methane hazard in a mine, whether or not the mine is classified as gassy. There was no consistent correlation between commodity mined and methane concentration, nor was there a correlation between mine depth and methane concentration. Neither of these factors can be considered a guideline for predicting methane hazards.

Jan 1, 1979

By Floyd G. Anderson

The Federal Bureau of Mines promotes the use of safe and effective dust-collecting devices for rock drilling in coal mines. To insure that such devices are available to the coal-mining industry, the Bureau issues certificates of performance for dust-collecting systems and certificates of approval for dust collectors and rock drills or other mining equipment with integral dust-collecting systems that meet the requirements of an established Schedule.4/ Investigations are conducted under the provisions of the current revision of this Schedule by engineers of the Branch of Health Research. This circular describes briefly the requirements and procedure for obtaining certificates of performance or approval and lists equipment that has been certified as permissible under Schedule 25 or its revisions as of January 31, 1961. The names and addresses of companies to which certificates have been issued are listed alphabetically at the end of this circular.

Jan 1, 1961

By P. M. Brown

The Bureau of Mines is investigating a dewatering technique for coal-clay waste that uses a flocculant, polyethylene oxide (PEO). This flocculant forms strong stable flocs that can be dewatered on a static screen. A field test unit (FTU) using this technique was operated at approximately 400 gal/min, using a waste stream from the flotation circuit of a coal preparation plant. Consolidated coal-clay material con-taining 55 to 60 pct solids was produced when the flotation circuit slurries of 2.7 to 8 pct solids were treated with 0.1 to 0.3 Ib PEO per ton of solids. The FTU was also operated at 64.5 and 87.5 gal/min using a portion of the underflow slurry from the preparation plant's thickener. Consolidated coal-clay material containing 55 to 60 pct solids was produced when the thickener underflow slurries of 19 to 24 pct solids were treated with 0.08 to 0.2 Ib PEO per ton of solids. PED-treated materials continued to dewater when placed in a pit.

Jan 1, 1983

By G. R. Palmer

Using a fluidized, countercurrent multiple-compartment ion-exchange (MCIX) column previously developed by the Bureau of Mines, Bureau researchers have successfully extracted uranium from a simulated acidic in situ leach liquor that contained 150 ppm U30s? This successful demonstration of the MCIX system is reported, and the effects of varying the operating conditions on the performance of the system are also examined. Operating the MCIX system with a flow rate of 15 gpm/ft2 and an aqueous-to-resin flow ratio of 200:1, more than 90 percent of the uranium Has extracted, and a resin containing approximately 28 grams U308 per liter was produced. The absorption column used to investigate the operating variables was approximately 18 feet long with a 2-inch ID and was divided into compartments that were 1 foot long.

Jan 1, 1980

By Herbert R. Babitzke

The purpose of this investigation was to optimize the high-temperature properties of columbium and tantalum. Columbium and tantalum were combined with selected alloying elements to achieve solid solution and dispersion strengthening. Fifty-six alloys were evaluated to determine their formability, hardness, strength at elevated temperatures, and oxidation resistance. The following six alloys showed high-temperature strength: [Cb-15Hf-5W-2Zr-4Al-4Ti-2N Cb-15Hf -5W-5Zr Cb-15.3Ti-4.1Zr-13.7Hf Ta-20Hf-4Al Ta-30Hf-4Al Ta-20Hf-5W-4Al] At 1,200° C, the columbium alloys had strength values of 40,000 psi or greater, and the tantalum alloys had strength values from 50,000 to 58,000 psi. For a 2-hour test period at 1,000° C, weight gains of only 9 and 8 mg/cm2, respectively, were observed on oxidation testing of two alloys, Cb-15Hf-5W-2Zr-4Al-4Ti-2N and Ta-20Hf-5W-4Al.

Jan 1, 1968

By T. J. Ballard, Austin B. Clayton

"The Union Copper mine is in the Gold Hill district, Rowan and Cabarrus Counties, N. C.The mine was discovered in 1799 and first worked as a gold mine; but copper was encountered at depth, and the property became an important producer of copper. It is estimated that the mine produced 5,000,000 pounds of copper before operations were discontinued in 1907.As part of the strategic minerals program, the Bureau of Mines conducted a development project on the property from July 1943 to November 1943. Eight diamond-drill holes, totaling 2,500 linear feet, were drilled to delineate the ore body. Analyses of 205 core samples were made.Tabulations of sample analyses and drill-hole logs are presented in this report.The project work embodied in this report was under the immediate supervision of Austin B. Clayton, project engineer, and the general supervision of H. B. Ewoldt, district engineer for North Carolina and Tennessee. The preliminary report, written by Austin B. Clayton, was revised and the various figures redrawn for publication by T. J. Ballard under the general supervision of M. H. Kline, chief, Raleigh Branch, Mining Division.Acknowledgment is due the Metallurgical Branch for analytical determinations of the samples.The mine property is 1.5 miles southwest of the village of Gold. Hill, N. C. (fig. 1). Gold Hill is on U. S. Highway 52 between Salisbury and Albemarle and on a branch line of the Southern Railway. The latitude is 350 30' and longitude 80° 21 The tract consists of 553-1/2 acres in Cabarrus and Rowan Counties.A tentative list of the surface-rights ownership is as follows: William Hoy Barringer - 16 acres, A. W. Tucker - 1 acre, Frank Wagoner - 4 acres, and George Barringer - 3-1/2 acres, in Cabarrus County; A. W. Tucker - 2 acres, H. N. Hedrick - 54 acres, and William Atkins - 473 acres, in, Rowan County, N. C.The mineral rights are owned by Alfred Rossiter, Alice R. Hesslein? and the estate of the late Bella Rosenblatt. The attorneys for the owners are Neidle & Taylor, 6 East 45th Street, New York City.The Union Copper mine is in the Cold Hill mining district of North Carolina where gold was first discovered in 1799. The upper parts of the veins in the district were first worked for gold; however, the increase in the sulfide content of the veins with depth rendered the amalgamation process for gold recovery ineffective, and the mines were closed.The period of greatest activity at the Union Copper mine was from 1899 to 1906. At an earlier period the oxidized and leached part of the lode near the surface was mined from a working known as the ""big cut,"" the reported yield of which was $300,000 in gold.3/ The mine has not been operated since 1907.J. T. Pardee3/ lists the probable value of the production of the Union Copper mine as $1,050,000, of which about $675,000 was the value of some 5,000,000 pounds of copper produced."

Oct 1, 1948

By M. P. Ristenbatt, E. K. Holland-Moritz, K. Metzger

A new post-disaster signalling system for the Bureau o Mines, using through-the-earth EM propagation, was successfully field-tested in the Lake Lynn test mine. Successful detection at an estimated input SNR of -30dB was accomplished using a coherent integration time of 4.46 minutes. The transmitted waveform consisted of a repeating pseudonoise maximal length sequence phase modulating a 1950Hz carrier. The receiver used a sliding-window matched filter, optimal for signal known exactly except for phase and starting time, implemented via a special purpose processor. Parallel processing permits adaptive signalling, where the detection (integration) time is determined by the actual input SNR encountered. This field test demonstrates a trapped miner detection system that is about 36dB more sensitive than a current pulsed system. This increased sensitivity permits some desired combination of increased range, shorter detection time, and reduced transmitter power or antenna-size. The combination of pulse-compression-type-signal, coherent integration, parallel-processing, and output peak-detection algorithms permit implemention of an ultra-reliable detection system. The same combination is compatible with digital Pulse Position Modulation and Emitter position location strategies.

Jan 12, 1983

By A. G. Smelley

As part of research conducted in its mission to effect pollution abatement, the Bureau of Mines, U. S. Department of the Interior, is developing a dewatering technique that allows for disposal of phosphatic clay wastes, for reuse of water now lost with clays, and for reclamation of mined land. The technique utilizes a high-molecular-weightnonionic polyethylene oxide polymer (PEO) that has the ability to flocculate and dewater phosphatic clay wastes. A synergistic flocculation study was made to determine whether a portion of PEO could be replaced by other reagents. Several groups of reagents were tested: (1) those that increased the zeta potential of the phosphatic clay wastes; (2) those capable of hydrogen bonding; and (3) those which flocculated the phosphatic clay waste. Reduction in PEO consumption occurred only with addition of those reagents able to flocculate the slime. The use of natural guar gums resulted in a lower PEO requirement and also yielded a dewatered product of higher solids content, 43 to 45 percent, versus 33 to 35 percent obtained with PEO alone.

Jan 1, 1980

By J. B. Janus

This report, the 22d in a series, gives analytical data showing composition and quality of tipple and delivered samples of coal collected during fiscal year 1972. This coverage lists mines located in 20 States. Ultimate analyses are given for most of the coalbeds listed. Tipple samples were collected by Bureau of Mines engineers at tipples as coal was being loaded into railroad cars or trucks. The deliveries were sampled in accordance with instructions issued by the Bureau of Mines, and the samples were analyzed in the Bureau laboratory at Pittsburgh.

Jan 1, 1973

By Edward B. Kendall

[This paper is one of a series being prepared far and published by the United States Bureau of Minus describing the methods of mining used and operating costs obtained in producing land and gravel from deposits throughout the United States. This circular describes operations at the Eliot plant of the Pacific Coast Aggregates (Inc.). in Livermore Valley near San Francisco, Calif. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent local expenditures only and not total production posts. It is recognized that publication of total costs might in some instances cause embarrassment to individual producers as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue.]

Jan 1, 1933

By J. G. Eisele

Solvent-extraction characteristics of dodecyl phosphoric acid (DDPA) were investigated to determine its potential as a fractional or selective extract-ant for individual elements in a rare-earth-yttrium mixture. The DDPA is an effective extractant for splitting rare-earth mixtures into light and heavy subgroups. Yttrium normally extracts with the heavy rare-earth elements but may be shifted toward an extraction sequence with the light rare-earth elements by increasing the pH. Elements in the light and heavy ends of the rare-earth series can be separated from middle-group rare-earth elements by using diethylenetriaminepentaacetic acid (DTPA) as an aqueous phase counter-extractant. Hydrogen-ion dependency of the distribution coefficients differs from that reported for similar systems at tracer-level concentration.

Jan 1, 1965

By A. L. Engel

This report is a compilation of preliminary and, in some cases, more extensive concentration experiments by the Federal Bureau of Mines on low-and medium-grade fluorspar ores from three localities in Nevada and one in California. The work was done on samples obtained from Shoshone mine, Nye County, Valery mine, Pershing County, and the Broken Hills mine, Mineral County, all in Nevada, and Dirty Weather mine, Inyo County, Calif. These investigations were made to aid in the development of domestic fluorspar resources, in line with the Bureau's long-established program of conservation of mineral resources. The treatment methods employed in the experimental work described included simulated or "heavy-liquid" gravity concentration of coarse minerals and comparatively fine-grained minerals, and flotation concentration of finely-ground minerals. These methods were attempted in order to beneficiate the ores and produce concentrates which could be marketed readily, with as high a recovery rate as possible, while using simple treatment methods suitable for small-scale operation.

Jan 1, 1961

By L. B. Pankratz

High-temperature heat contents were measured for two praseodymium oxides and three terbium oxides. There were: Pr2O3 (298° to 1,600° K), PrO1.833 (298° to 1,050° K), Tb2O3 (298° to 1,600° K), TbO1.719 (298° to 880° K), and TbO1.812 (298° to 850° K). With the exception of PrOl.833, all results were regular. PrO1.833 had a small thermal anomaly at 760° K with an extra absorption of 380 cal/mole. The measured heat content values, tabulated smooth heat contents, and entropy increments are reported. Heat content equations were derived.

Jan 1, 1966

By W. E. Wallace

Volume-rate-of-flow measurements were made of the flow of mercury through porous samples under conditions of no field, magnetic field transverse to the direction of flow, and transverse magnetic field and electric current to determine if a magnetic method might be potentially useful in the study of pore-size distribution. No change was observed in the flow rate from the application of a magnetic field alone. The application of both field and current produced an electromagnetic pumping action with or against the direction of flow, depending upon the direction of the electric current. This pumping effect was observed to be greater in a rectangular porcelain sample than the calculated value for an equal-Sized open channel.

Jan 1, 1969

By John A. Organiscak

[Fugitive Just is generated alone unpaved mire reads from intermittent equipment traffic. Typically, the majority of such traffic consists of trucks hauling either mine product or waste [rum the surface mime pit and/or the processing plant. Fugitive dust generated along these unpaved mine roads includes particles of all sizes which become airborne. The potential hazards include the deleterious effects to human health of inhaled dust, traffic visibility hazards and environmental impacts on the localized area by the larger-sized visible airborne dust. Two held surveys were recently conducted to quantify fugitive dust generation and dispersion from truck traffic on unpaved and untreated mine haulage roads For these surveys., airborne glow sampling was conducted at multiple sampling fixations away from an unpaved haulage road at a limestone quarry/plant and at a coal mine preparation plant lo measure the size characteristics, concentrations. and dispersive behavior of the dust cloud generated from truck traffic- Results show that at least 80% of the airborne Just generated by haul trucks was larger than 10 µm- Airborne respirable, thoracic, and total dust concentrations all decreased and approached background concentrations 30.5 in (100 feet) from the road This report describes the average and instantaneous peak dust levels that were measured tip to 30.5m (100 feet) Iron the haulage road. Keywords: Unpaved mine road, fugitive dust, silica.]

Jan 1, 2008

By R. W. Stahl

"This study by the Federal Bureau of Mines was confined to pillaring with continuous mining machines and to mines where total extraction is practiced. Many different conditions and practices in as many coalbeds as possible in Pennsylvania were observed.Pillar extraction or pillaring can be the most productive part of coal mining if done properly; but it also can be the most dangerous if done improperly.Because of the need for more careful planning before and caution during pillaring, many mining companies resort to the undesirable practice of stumping or hogging of pillars with subsequent unnecessary waste of valuable natural resources. Pillaring can be done at reasonable cost and safely, as proven at many mines where complete extraction is practiced and enviable cost and accident records are maintained.Although continuous mining machines are bulky and sometimes difficult to maneuver, they have been used with great success in pillaring. Occasionally, however, a machine is caught, or men are injured by a fall during pillar recovery. This Bureau survey was conducted to ascertain how safe and successful pillaring (especially the removal of final stumps in lifts or the final stump of a pillar), is accomplished in some mines, while others have considerable difficulty under similar conditions.The Bureau hopes the information to be presented in this publication will prove beneficial to those who wish to recover more pillar coal and to improve their accident record during such procedures."

Dec 1, 1959

By Will H. Coghill

[The supply of gravel spar and of acid spar is not well balanced. Gravel spar -- 85 per cent flourspar, 5 per cent silica -- gluts the market, whereas acid spar -- 98 per cent fluorspar, 1 per cent silica -- is somewhat scarce. Hence it is desirable to convert some of the gravel spar into acid spar. Knowledge of this condition prompted the Franklin. Fluorsrar Co. at Paducah. Ky., to enter into cooperation with the U. S. Bureau of Mines and the Missouri School of Mines and Metallurgy to improve the methods of fluorspar, milling so that morn acid spar would be available. The fluorspar company detailed Mr. Omar Greeman for the work. During the course of the investigation, while Mr. Greeman was also doing work for a master's degree in the School of Mines? an extensive study was made of gravity concentration of fluorspar ores. Decrepitation by heat treatment was also given a laboratory try-out. A part of tie time was spent on flotation; these notes relate only to the flotation. The results of one of the flotation runs is appended. The test was made in a 500-gram mechanical-agitation machine. The sample was ground to 100-mesh in a pebble mill.]

Jan 1, 1928

By Gerald W. Elger

A new process under development by the U.S. Bureau of Mines for producing synthetic rutile from ilmenite is described. Rutile formation is based on oxidation and fluxing of titania slag produced by electric furnacing of ilmenite. Laboratory tests show that phosphorus pentoxide flux additions to oxidized slag enhance conversion to rutile by forming a phosphate-based glass matrix. This matrix contains most of the major impurities, including the oxides of iron, aluminum, magnesium, manganese, and silicon. Rutile crystals of 5 to 150 microns in size were formed in slags heated to temperatures of 800° to 1,550° C. The synthetic rutile crystals were liberated from ground slag by treating with phosphoric acid to weaken the glass matrix, followed by attrition scrubbing. Rutile fractions analyzed as high as 94 percent titania content. In several instances, more than 90 percent of the titanium in the shag was recovered to yield combined rutile fractions containing 90.2 to 92.6 percent titania.

Jan 1, 1971

By J. H. Hild

The Shanton magnetite-ilmenite deposits lie on the east flank of the Laramie Mountains, 43 miles northeast of Laramie, Albany County, Wyo. (fig. 1). The Shanton and other similar deposits in the Laramie Mountains were examined by Bureau of Mines engineers during 1942, 1943, and 1945, and a report2/ describing the results of a dip-needle survey and surface sampling was published in 1946. The Shanton deposits occur in a relatively flat section of the range at altitudes varying from 7,500 to 1,650 feet (fig. la). Prevailing rocks in the Shanton area consist of anorthosite with intrusive dikes of gabbro differentiates and granite. Titaniferous magnetite outcrops in five masses, which are separated at the surface by overburden and anorthosite.

Jan 1, 1953

By O. E. Traubert, E. G. Meiter

"The daily sulphur dioxide content of the air at the Pittsburgh Experiment Station of the Bureau of Mines was determined by the bureau at the request of Committee D-14 on Screen Wire Cloth of the American Society for Testing Materials. The purpose of the investigation was to obtain data for use in interpreting screen-corrosion tests, which were conducted simultaneously and jointly by the committee4 and the Bureau of Mines.The plan of this investigation was to vale a single daily determination, except on Sundays and holidays, of the SO2 content of the atmosphere at the exposed test screens, for a period of one year. No attempt was made to determine the variation during the day, except on the morning of October 15, 1927, when the atmosphere was unusually foggy and smoky. Several successive determinations were made on that date to ascertain changes in the SO2 as the morning haze disappeared. The SO2 determinations were begun on August 11, 1927, and continued until August 11, 1923.The Pittsburgh Experiment Station of the Bureau of Mines is in a residential section about 3 miles east of the central or main business district of Pittsburgh. The air samples were taken on the roof above the auditorium, or the center rear of the building. This was also the place where the pieces of screen were placed for corrosion tests. The height was about 40 feet above ground level. Several sources of considerable smoke and SO2 are in the immediate vicinity. On the west side of the building is a double-track railroad. At this point the line runs through a cat below the level of the building. The horizontal distance between the air-sampling position and the railroad tracks is about 400 feet, and the vertical distance about 70 feet. The power plant for the Bureau of Mines building is about 250 feet south of the sampling position. About 1000 feet farther to the south are the engineering building and power plant of Carnegie Institute of Technology, and 1/4 mile to the southwest is the power and heating plant for the Carnegie Library and Museum. About 1 to 2 miles farther south and also southwest"

Jun 1, 1930