Search Documents

By G. W. Grove, E. E. Quenon

"INTRODUCTION During September, October, and November 1946 the Safety Division of the Bureau of Mines, off' the United States Department of the Interior, Pittsburgh, Pa., tested four new types of self-contained breathing apparatus and approved them in accordance with Schedule 13C. Approval was granted with the proviso that certain specifications outlined on the approval plate be made fully effective, and with the understanding that established safe practices in training in the care and use of self-contained breathing apparatus are of major importance.The excellent records made during the past 30 years in the safe use of self-contained breathing apparatus, some of which required the almost continuous wearing of apparatus during several hours daily for days, weeks, or months, may be attributed largely to the Bureau's system of rescue organizations, selection of physically fit rescue workers, effective training, and educational work done in rescue and recovery operations during fires or following disasters and in the care and use of self-contained breathing apparatus. Loss of life during wearing of breathing apparatus was due almost invariably to poorly assembled or otherwise defective apparatus, poor physical condition of the wearer, or insufficient training or some incorrect procedure.The newly developed breathing apparatus are of much simpler design than the conventional type used for the past several years; however, it is just as important to select rescue crews carefully and to train them properly in the care, use, and limitations of the new types of apparatus as for the older long-established types, if anything like safety is to be achieved in using them. The Bureau of Mines considers that 1/2-hour and 3/4-hour self-contained breathing apparatus should be used only as auxiliary equipment in mine rescue and recovery work, and their capabilities and limitations should be well understood by those who wear them."

Jul 1, 1947

By Peter W. Kauffman

This Bureau of Mines publication is designed primarily to provide mine engineers and production-level mine managers with the following: 1. Information to assist them in making the decision to retreat mine and in selecting the best retreat mining technique for specific mining conditions. 2. Information on mine planning that will enable them to design mine layouts for safe and efficient retreat mining. 3. Information that will enable them to develop a section foreman's handbook. The manual has been organized to gradually increase in level of detail as the reader progresses from beginning to end. Individuals interested in an overview of retreat mining can confine themselves to the first few chapters. Those interested in mine planning, should read the middle chapters as well. Those interested in the development of a foreman's handbook should read the entire manual.

Jan 1, 1981

By James D. Noll, Jon A. Hummer, Shawn E. Vanderslice, Aleksandar D. Bugarski, George H. Jr. Schnakenberg, Steven E. Mischler, Larry D. Patts

The National Institute for Occupational Safety and Health designed and conducted a study in an underground metal mine to assess the effects of selected diesel emissions control technologies on the concentrations of diesel particulate matter and gases in underground mine air. The control technologies studied included diesel particulate filter (DPF) systems, filtration system with disposable filter elements, diesel oxidation catalytic converter, and biodiesel blends. Each technology was tested on a mining vehicle operated in an isolated area of an underground mine supplied with fresh air. These isolated zone tests allowed for the operation of vehicles under conditions and over duty cycles that closely mimic actual duty cycles of production equipment. The DPF systems reduced the elemental carbon (EC) concentrations in mine air between 88% and 99%. The same systems reduced total particulate matter (TPM) concentrations in mine air by approximately 75%. The biodiesel blends B20 and B50 caused a reduction in the EC concentrations of 26% and 48%, respectively. Those blends also reduced TPM concentrations by 9% and 24%, respectively. The use of #1 diesel fuel reduced EC concentration by 13% compared to #2 diesel fuel. An increase in nitrogen dioxide concentration of up to two times was seen when platinum-catalyzed DPF systems were tested.

Jan 5, 2006

By Slavoljub D. Maksimovic

The Bureau of Mines, through a memorandum of agreement with the State of Ohio, tested a method of constructing seals in abandoned mine openings in Ohio by means of pneumatic stowing of crushed limestone and gravel with sand. A total of five openings and one shaft were back-filled. Pneumatic stowing uses compressed air to convey material through a pipeline and into the mine opening. The stowing equipment consists of a power supply, a blower, a feeder to inject the material into the pipeline through an airlock, and a nozzle for directing the placement. Material is ejected from the nozzle at high velocity, creating a high-compaction fill upon impact. Well-graded aggregate up to 2 inches in diameter and having sufficient fines is used as fill. The stowing method is safer and faster than conventional methods, is cost competitive, prevents trespass into abandoned mine openings, and eliminates or reduces the exposure of workers to possible hazards since the discharge nozzle can be kept at the mouth of the opening. The equipment is mobile, and, with some modification, the technique could be widely used for sealing abandoned and active mine openings, even in remote locations and during severe weather conditions.

Jan 1, 1982

By James P. Ulery

Explosions in U.S. coal mines have caused death and injury to miners and destruction of workings since the first reported explosion in 1810. These explosions are caused when buildups of explosive gas and/or dust in the mine are ignited by the presence of a flame or spark. Methane gas is inherently generated and held by adsorption in coal and is normally liberated during mining. Because this gas is explosive in the range of 5%–15% by volume, fresh air is constantly supplied to the working face to prevent the methane/air mixture from reaching this explosive range. The required amount of ventilation air is based on estimates of gas release under normal conditions. Occasionally, unanticipated and unusually high emissions are encountered, which, despite normal ventilation controls, result in an explosive mixture that a spark from a cutting bit or electrical equipment can easily ignite. Investigations have shown that such emissions are often associated with anomalous geologic features or conditions. Although most operators are aware that certain geologic features may adversely affect productivity, few are aware of their potential as a gas emission hazard. This report presents a historical framework detailing the impact of geologic features on excess gas emissions and resultant mine explosions. It also provides operators with specific information on recognizing and alleviating potential hazards from methane emissions related to these geologic features.2

Jan 4, 2008

By Joan T. May

The Bureau of Mines conducted laboratory tests to evaluate the production of high-purity H3P04 by HCl digestion and solvent extraction. Both batch and bench-scale continuous tests were made. Western phosphate rock concentrates were acidulated with HCI, and the digestion liquors were processed by solvent extraction. Phosphoric acid was extracted with isoamyl alcohol and recovered from the organic extract by contact with an NH4F solution. This solution was fractionally distilled to yield high-purity H3P04. The raffinate from solvent extraction was treated with lime to precipitate CaF2, which was subjected to steam pyrolysis to generate HF. This method was successful in recovering 95 pet of the phosphate and 80 pct of the fluoride contained in the concentrates.

Jan 1, 1976

This Bureau of Mines publication summarizes the industrial minerals industry of Idaho. It contains information on 119 principal deposits of 21 commodities in the State and describes the institutional and infrastructural factors affecting mineral development.

Jan 1, 1991

This report describes the development of training materials for the operators of underground mining equipment in the underground metal and nonmetal mining industry. The objective was to determine the effectiveness and acceptability of these training materials and to provide the validated training materials to the industry. Ten modules were developed, based on industry need according to accident frequency, accident severity and exposure to the equipment. The final modules were an average of 20 minutes in length and used slides with synchronized narration on cassette tapes. Testing materials are included for use by the mines.

Jan 1, 1984

By Steven J. Page, Wm. Randolph “Randy” Reed, John A. Organiscak

Researchers studying dust generation from blasthole drills developed a simple, quick fix that reduced respirable dust concentrations by more than 63% at the dump point. This device, which requires almost no maintenance, is small and inexpensive, and it will help operators maintain compliance to the dust standard. The thought process was that a reduction of respirable dust at any of the multiple sources on the drill, in this case the dust collector dump point, should reduce the total respirable dust generated by the drill. The U.S. Mine Safety & Health Administration (MSHA) has a coal respirable dust standard of 2 milligrams per cubic meter (mg/m3) for an 8-hour shift. MSHA and mine operators periodically collect personal dust samples to determine compliance with this dust standard. Drill operators have one of the highest exposure levels to respirable dust. This has been proven through many reviews of the MSHA dust sampling database. Prior to 1987, the highwall driller at surface coal mines had the most severe exposure to respirable silica dust, a trend that continues today based on MSHA's respirable dust sampling database. A review of the MSHA database for the years 1985 through 1992 shows that 81% of the respirable silica dust samples taken exceeded the permissible exposure limit for the highwall drill operator at surface coal mines. A more recent review of the MSHA database, for the years 1996 through 2000, shows that only 31% of the respirable silica dust samples taken exceeded the respirable silica dust limit for the highwall driller at surface coal mines. This suggests a substantial improvement in preventing the exposure of silica dust to the highwall drill operator. The drill operator, however, still tops the list of job occupations that have the highest exposure to respirable silica dust Respirable dust has been shown to be harmful to human health, especially when silica is present in the dust. It causes a disease known as silicosis, which can occur in three levels: chronic silicosis, which occurs after 10 years of exposure; accelerated silicosis, which occurs between 5 and 10 years of exposure; and acute silicosis, which can occur within a few weeks to five years of very high exposure to silica dust. Respirable dust consists of the dust particle size fraction whose median diameter is 4 micrometers (µm). The drilling machine generates high concentrations of respirable dust from several sources: drill table shroud leakage, dust leakage through the table bushing, dust discharge from the dust collector exhaust due to impaired filters, and dust entrained from the dust collector fines dumped onto the bench. The National Institute for Occupational Safety and Health's (NIOSH) Pittsburgh Research Lab (PRL) has been studying different methods to reduce respirable dust from these sources. During its testing, the institute identified a simple solution that reduces the amount of respirable dust generated at the collector dump point.

By R. E. Gray

[The purpose of the study is to investigate cases of subsidence over abandoned mined-out areas of the Pittsburgh Coal identified from published and unpublished sources and to determine through a consideration of the geology, topography, climate, mining activity, and evidence at ground surface, what mechanisms control subsidence .and under what circumstances it takes place. The study wan performed it two phases, the first to identify all documented incidents of subsidence in mined-out areas of the Pittsburgh coal Region; and the second, to study a particular portion of the region in detail, collecting pertinent data relative to the sites within, characterizing roil the nature of the subsidence and its economic consequences, and determining the applicability of the findings to other areas whore similar problems with the collapse of abandoned miner have been encountered.]

Jan 1, 1977

By D. Harrington

Hatch (260) made the following pertinent statement regarding the present status of engineering design of dust-control equipment: Textbooks on ventilation and engineering handbooks devote little or no space to methods of control of industrial dust, and in the technical journals papers on fundamental engineering design of equipment are conspicuous by their absence. In a recent bibliography of the literature on pneumoconiosis less than 1 percent of the articles dealt with the engineering control of the disease. The science of dust control has not developed beyond the stage of trial and error, and the design of structures for the suppression of dust is based almost entirely upon empirical data together with one or two elementary formulas. The latter were derived from the generalized experience in a limited number of Industries such as woodworking, where conditions and requirements are not at all like those, for example, in a sand-pulverizing plant. Wide experience and good judgment are essential to the proper use of the scanty information that has been collected and systematized. Without attempting to minimize the importance of experience in engineering design, it is necessary to point out that most of the past experience obtained in the empirical design of dust-control equipment was not evaluated by means of quantitative studies of the actual reduction in dust , fence, past experience does not necessarily furnish the proper guide for future design. In fact, recent surveys in certain industries, employing modern methods of investigation, have shown that existing equipment is in many cases inadequate.

Jan 1, 1935

By P. M. Daling

This report, sponsored by the U.S. Bureau of Mines, presents the results of an examination of available safety assessment methods and their applicability to the mining industry. Standard safety analysis procedures were evaluated for relevance to the mining industry and mine operators' needs. The major safety concerns and needs of mine operators were identified through telephone contacts and a visit to a mine site. Safety assessment methods recommended for use by the mining Industry were also Investigated for potential adaptability to a user-interactive computer system. Several methods were determined to be immediately transferrable to the mining industry; these techniques are described in a user's handbook produced as part of this project. The handbook gives detailed instructions on appropriate application and utilization of these methods. Other techniques will require further development before they can be effectively transferred to the mining industry. These methods, their advantages, disadvantages and resource requirements are described in the final project report. Recommended system safety analysis techniques facilitate an evaluation of total mine system safety and a determination of safety-related interactions among systems within a mine. The application of these methods to the mining industry could result in reductions in both the frequency and the consequences of mine accidents.

Jan 1, 1983

By John P. Capp

After World War II the Bureau of Mines studied methods of producing synthesis gas including a plan to gasify coal in place. Consequently, under a cooperative agreement with the Alabama Power Co., Bureau engineers directed a series of experiments that were carried out on the property of the Alabama Power Co. at Gorgas, Ala. The purpose of underground gasification of coal, regardless of method used, is to obtain the energy contained in the fuel for use on the surface, without mining in the usual sense of the term. Underground gasification can be described as (1) a process where coal, in place, is consumed by partial combustion with air, oxygen, steam, or any combination of these to produce a low calorific value gas (80 to 300 Btu per cu ft) or (2) a complete combustion process in which air is used to produce a gas containing carbon dioxide, nitrogen, and considerable thermal energy.

Jan 1, 1963

By John P. Capp

After World War II the Bureau of Mines studied methods of producing synthesis gas including a plan to gasify coal in place. Consequently, under a cooperative agreement with the Alabama Power Co., Bureau engineers directed a series of experiments that were carried out on the property of the Alabama Power Co. at Gorgas, Ala. The purpose of underground gasification of coal, regardless of method used, is to obtain the energy contained in the fuel for use on the surface, without mining in the usual sense of the term. Underground gasification can be described as (1) a process where coal, in place, is consumed by partial combustion with air, oxygen, steam, or any combination of these to produce a low calorific value gas (80 to 300 Btu per cu ft) or (2) a complete combustion process in which air is used to produce a gas containing carbon dioxide, nitrogen, and considerable thermal energy.

Jan 1, 1963

By Robert E. Hershey

1. This investigation shows that the most important beds in Claiborne County, from the standpoint of present production and reserves, are the Coal Creek and Jellico. Together, they contain 69 percent of the known recoverable reserves in the county. Reserves in five other beds are tabulated in this report; in order of quantity of reserves, they are: Blue Gem, Lower Pioneer, Pewee, Big Mary, and Rex. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated to be 60 million tons, as of January 1, 1953. Of this total, 55 million tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager to permit making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1956

By T. A. Sullivan

The processing of sweated aluminum electronic scrap was investigated to develop methods for recovering the aluminum and concentrating the other metals, including copper, lead, gold, and silver, into a product that can be separated by known methods. Two molten-salt electrorefining processes were developed and tested. The first process utilized a three-layer refining cell with a BaCI2-NaF-AIF3 electrolyte, which operated at 750° to 850° C. The second process used an all-chloride electrolyte of NaCI-KCI-AICI3 at 750° to 800° C, with separate anode and cathode compartments. High-quality aluminum was recovered that averaged 99.8-percent pure in the three-layer cell and 99.6-percent pure in the compartment cell. Over 94 percent of the aluminum was recovered with cathode current efficiencies of approximately 90 percent in both methods. The copper, lead, tin, silver, gold, and other metals were concentrated threefold in an anode product. Separation of lead and part of the tin by liquation from this product seemed feasible. The anode product was smelted to prepare a 96-percent copper bullion that contained 690 ounces of silver and 65 ounces of gold per ton, with 98 percent recovery of these values.

Jan 1, 1972

By C. E. Wood

Because of the renewed importance of the strategic metal manganese the Bureau of Mines in conducting further research on pyrometallurgical methods of beneficiating manganiferous iron ores and low-grade manganese ores. Published data on the Pyrometallurgical of manganese ores have been reviewed by Joseph.5/ A method of treatment that has received less consideration than others is the matte smelting of manganese or the separation of manganese from the iron and the gangue in an ore b, formation of a matte, that consists principally of esulfide of manganese. A procedure of this type has been patented by Betts.6/ Lofquist7/ claims advantages for the production of a sulfide-oxide matte as a method of recovering manganese in alloys containing manganese and iron.

Jan 1, 1940

By Compiled by Staff

"INTRODUCTIONThe U.S. Bureau of Mines (USBM) was established in the public interest to conclude inquiries and scientific and technologic investigations on mining and the preparation, treatment, and utilization of mineral substances; to promote health and safety in the mineral industries; to conserve material resources and prevent their waste; to further economic development; to increaseee efficiency in the mining, metallurgical, quarrying, and other mineral industries; and to inquire into the economic conditions affecting those industries. The organic act of the Bureau, as amended by Congress and approved February 25, 1913, made it the province and duty of the U.S. Bureau of Mines to ""disseminate information concerning these subjects in such manner as will best carry out the purposes of this Act.""In accordance with this directive, USBM reports the findings of its research and investigations in its own series of publications and also in articles that: appear in scientific, technical, and trade journals; in "" proceedings of conventions and seminars; in' reference books; and in other non-USBM publications. The number of these reports, the wide range of subjects they cover, and the variety of mediums in which they appear make this kind of list both necessary and valuable.This edition describes reports and articles published during calendar years 1992 and 1993. It supplements the 50-year list of Bureau publications from July 1, 1910, to January 1, 196O 2; and these 5- year lists of publications and articles: from January 1, 1965, to December 31, 1969 4, from January 1, 1970,to December 31, 19745 , from January 1, 1975, to December 31, 1979 6 , from January 1, 1980, to December 31, 1984 7 , and from January 1, 1985, to December 31, 1989 8."

Jan 1, 1994

By N. Kyriazi

The U.S. Bureau of Mines subjected the CSE SR-lOO self-contained self-rescuer (SCSR) approved by the National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) to a series of laboratory treatments designed to simulate various environmental conditions in underground coal mines. The tests were designed to predict the ability of the self-rescuers to withstand those environmental stresses without causing a decrease in wearer protection. The apparatus were heated to 710 C for 48 h, cooled to -450 C for 16 h, vibrated for 9 h, and dropped 1 m on each axis. A critical concern was internal damage to an apparatus, without any obvious external signs, that would cause it to malfunction or seriously degrade its performance. Carbon dioxide (C02) levels in apparatus with combined treatments were higher than in apparatus with individual treatments and untreated apparatus. The higher levels remained within safe limits, however. None of the treatments caused venting of the small oxygen cylinder that provides starter oxygen. Some bottles were found to be empty because of manufacturing defects in the burst disks. This problem was corrected in later models. The heat treatments did make the case ends more difficult to remove and the breathing bag sticky and subsequently more difficult to unfold. An apparatus that was dropped and vibrated had a broken desiccant bag that released some of its contents which compromised the seal of the relief valve. The case was dented from the drops. As with the first-generation self-rescuers, if there is visible damage to the case of the apparatus, the apparatus should be considered to be internally damaged and must be removed from service.

Jan 1, 1990

By Bill M. Stewart

Since 1974, a large amount of data has been developed concerning the physical properties and stability characteristics of waste generated by the mining and preparation of bituminous coal. However, very little information has been developed on the properties and characteristics of anthracite waste. During this Bureau of Mines research project, coarse anthracite breaker refuse from five sites in eastern Pennsylvania was sampled and the physical properties, which indicate stability characteristics, were determined in the laboratory. Coarse anthracite breaker refuse is quite similar to coarse bituminous refuse in chemical and mineralogical composition. However, the physical properties of the anthracite waste materials tested are different from those of coarse bituminous refuse. For the coarse anthracite breaker refuse tested, the average maximum laboratory density is 113.2 lb/ft3, the average angle of internal friction (direct shear) and average cohesion are 30.2° and 2.6 psi, respectively, and the average permeability (four sites) is 1.24 x 10-2 cm/sec. Stability analyses were conducted on six theoretical anthracite waste embankments. These analyses show the effects on minimum safety factors of geometry, phreatic surface level, and physical properties.

Jan 1, 1983