Search Documents

By C. T. Baroch

As part of a general program for investigating all phases of titanium production, argon was substituted for helium in the reduction step at the Bureau of Mines pilot plant, which employed a modification of the Kroll, or magnesium-reduction, process. Argon was substituted for helium in 108 of the 140 batches of sponge made during 1 month's reduction operations for July 1954. Argon was substituted for helium satisfactorily, with only slight modifications in technique. Metal quality, feed rate of TiC14, magnesium efficiency, and average production per batch were closely comparable with either gas. Argon runs were slightly more troublesome because of the formation of condensable chloride complexes, which tended to plug feed and vent lines and to entrap deposits of lower titanium chlorides on the reactor-pot lids. These lower chlorides were objection-able because they were pyrophoric and created obnoxious fumes when pots were opened. When feed and vent lines became plugged care was required in poking or unplugging these lines to prevent air from entering the reactor. These problems were relatively minor, and continued development of reactors and techniques for the use of argon should further minimize objectionable side reactions obtained when argon is used.

Jan 1, 1956

By Guy E. Dent, Hugo E. Kuehn

"SUMMARYFor making a comparison of magnetic surveys measured from the ground and from the air, Worcester County, Maryland, was chosen as a proving ground. Vertical magnetic intensities were observed on the ground, and total magnetic intensities were observed from the air. A comparison of the two magnetic maps reveals similar large magnetic features, but these are displaced in some instances by distances greater than a mile. Magnetic terrane in the two charts is of the same type but often differs greatly in respective characteristic features.The sacrifices in accuracy that may be expected from the use of different systems of diurnal magnetic corrections on ground observations constitute a part of this report.INTRODUCTIONThe value of magnetic surveys for gaining information concerning the crystalline basement is recognized increasingly. That this topography is often reflected to a major degree in the overlying sediments with certain offsetting is well understood. Even where such sediments are deep, the surface topography of upper formations often reflects this bedrock topography to a certain degree."

May 1, 1947

By George L. Gates

It is generally recognized that if the lose and contamination of the fluid content of a core specimen from an oil- and gas-bearing formation in a well were eliminated, the value of core analysis would be increased greatly. In an effort to obtain uncontaminated cores, extensive field tests were carried out in the Mercy field, San Jacinto County, Tex., with the Carter pressure core barrel and an oil-base drilling fluid having very low rates of filtration as measured by the standard A.P.I. drilling-fluid filter teat. A tracer was added to the drilling fluid filter test. A tracer was added to the drilling fluid to provide a means for quantitatively measuring the volume of oil filtrate in the cores. Unfortunately, as stated in the report on the Mercy tests, very little oil nand was penetrated in coring the well; and because the performance of the pressure core barrel was not entirely satisfactory, the tests did not provide a complete answer to the question: Does a filtrate from an oil-base drilling fluid enter cores., and how does it affect the results of the core analyses?

Jan 1, 1950

By H. M. Cooper

The determination of moisture in coal is an empirical test, because the time, temperature, and equipment are specified. The essential features of the equipment and details of the procedure are given in A.S.T.M. Designation: D271-44.:2. According to the specifications, the following features should be incorporated in the equipment used: 1. Oven must have uniform temperature in all parts. 2. Oven must be constructed with minimum of air space. 3. Oven must have means of changing the air two to four times per minute. 4. Air must be dried over sulfuric acid (sp. f-7. 1.84). The analytical procedures governing most of the nation's coal purchases are those given in A.S.T.M. Standards referred to above. These standards are general arid of such scope as to cover all ranks and types of coal. In cases where only the moisture is required, a faster method than the standard procedure is desired.

Jan 1, 1948

By W. W. Adams

"A recent paper prepared by the writer summarized the results of an analysis of the accident records of 34 metal mines for the calendar year 1925. The present paper summarizes the results of a similar analysis of the accident records of 59 coal mines for the same year. This summary is based upon reports furnished to the Bureau of Mines, Department of Commerce, by operating companies that par¬ticipated in the National Safety Competition of 1925.The purpose of the Competition was to establish the lowest accident-severity rate, thus showing the smallest loss of time from accidents in proportion to total number of man-hours worked. The reports covered all lost-time accidents that occurred during the year, that is, all accidents that disabled an employee beyond the day or shift on which the accident occurred. Detailed information for each of the 59 coal mines is given in the appended table. Each mine employed at least fifty men underground; over half of than employed more than 200 men underground. Hence the accident records should be typical of those of large-scale mining operations in general where the company is devoting special attention to accident-prevention work. The mines covered by the reports are situated in eleven States: Alabama, Illinois, Indiana, Kentucky, Maryland, Ohio, Pennsylvania, Tennessee, Utah, Washington, and West Virginia.A tabulation of the reports covering the 59 mines showed an accident-frequency rate of 123 per million hours of ""exposure* and an accident-severity rate of 10.214 per thousand hours of exposure3. The total volume of exposure or employment was 29,117,561 hours, representing the equivalent of work of 12,000 men for three hundred 8-hour shifts. The records covered employment and accident above ground as well as underground, although they did not include stripping or open-pit mining. Accidents during the year resulted in 33 deaths, 1 permanent total disability, 28 permanent partial disabilities, and 3,510 temporary injuries. These accidents represented a loss of tine equal to 297,417 man days. In arriving at this lost-time equivalent, each fatality and permanent total disability was weighted at 6,000 lost days (see footnote 3), as specified in the scale adopted by the International Association of Industrial Accident Boards and Commissions; permanent partial disabilities were weighted according to nature of injury, in accordance with the scale adopted by the :Board; temporary injuries were weighted according to the actual number of calendar days during which the employee was incapacitated as a result of the injury."

Nov 1, 1926

By J. E. Berg

This paper3 describing the mining methods at the Page mine operated by the Federal Mining & Smelting Co., is one of a series being prepared by the United States Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. The Page mine is the most westerly of the producing lead-silver-zinc mines in the Coeur d'Alene mining district of Idaho, being situated 5 miles west of the city of Kellogg and at an elevation of 2,677 feet above sea level. It may be classed as one of the new active producers, of the district and owes its present activity largely to the development of floatation.

Jan 1, 1930

By P. G. Guest

"INTRODUCTION Need for More information on Spark IgnitionMany questions have yet to be answered more completely concerning the ignition of flammable gases and vapors by electric sparks. Among these one might mention the following: How do the mixture limits for ignition by sparks and by other means compare? Are the most explosive mixtures of the gases the most easily ignited? How ""hot"" must the spark be or what is the minimum energy required for ignition? Does the electric spark act merely as a source of thermal energy or do aggregations of ions, electrons, and metastable atoms formed during and just before the spark play an important part in promoting chemical reactions that ultimately lead to ignition? It is possible for ignition to occur as a result of a silent or brush discharge? How do the ignition energies with single and rapidly recurring sparks differ? What is the relative effectiveness of long, tenuous sparks in ignition as compared with intense, short-gap sparks of equal energy? What is the influence of the material, size, and shape of the spark electrodes? Does the energy for ignition change noticeably with moderate changes in pressure and temperature of an enclosed gas mixture? What order of lag exists between the occurrence of an incendiary spark and the first evidence of flame propagation? What part of a spark in space and time is most effective in producing ignition? Answers to these questions bear directly on the general problem of flame initiation and propagation and, if sufficiently comprehensive, should contribute much to an understanding of the actual mechanism of combustion."

May 1, 1944

By R. W. Huber, R. C. Wiley, V. C. Petersen

"Three arc- melted ingots, two of a t itanium-7 percent manganese all oy and the third of unalloyed titanium, were forged and rolled into 3/ 4-inch plate; comparative data were obtained on these processes. The finished plate, part of which was used by the Naval Bureau of Ordnance, was tested for mechanical and other properties.These properties were correlated with sponge purity, forging technique, rolling temperature, and cooling rate from the rolling temperature. For the alloy material, transformation data were obtained, and their age-hardening characteristics were studied. The temperature-impact relationship was established for rolled sections from all three ingots.INTRODUCTIONArc -melted ingots of unalloyed titanium and a titanium-manganese alloy were fabricated into plate under closely controlled conditions by personnel of the Metals and Alloys Section, Physical Metallurgy Branch, Bureau of Mines, College Perk, Md. This program was cosponsored by the Naval Bureau of Ordnance. Bureau of Mines interest lay in correlating the processing procedures with the mechanical properties of the finished plate.Considerable data have been published recently on constitution diagrams and properties of titanium-manganese alloys in genera1. 3/ 4/5/6/ However, little if any correlation between processing schedules and end results has been published, particularly with respect to the present commercial production of the proprietary titanium manganese alloys . Several factors in the production of titanium and titanium alloys have a pronounced influence on the physical and mechanical properties of the finished product: (1) The degree and nature of impurities in the base materials, ( 2) the amount of impurities introduced during the melting cycle and their distribution, (3) the homogeneity of the alloy, (4) forging, (5) rolling, and ( 6) final heat-treating cycles. All of these item£ are important from a metallurgical standpoint in producing the desired end properties in the metal."

Mar 1, 1955

By Townsend. James W.

"INTRODUCTION As a byproduct of its mineral investigation program, the Bureau of Mines has developed a number of operating devices and techniques worthy of note. This paper, prepared under the direct supervision of Paul T. Allsman, chief, Salt Lake City Division, Branch, and under the general supervision of Lowell B. Moon, chief, Mining Branch, reports upon one such device. A simple device has been developed for measuring angles of deviation from the horizontal as recorded on a glass tube by acid etching. The device has facilities, also, for measuring the angle between the long axis of the ellipse and the north-south reference points established by a Maas compass or from an established axial lamina, on the tube, which was ori¬ented to a specific direction in the hole by rod alinement.The device was found accurate within half a degree on repeated orientations of the same tube. However, the degree of accuracy is dependent on the accuracy of personal manipulation in orienting the tube to the correct plane."

May 1, 1947

By R. H. Jefferson

An electrochemical method to selectively determine sulfur dioxide in the presence of sulfur trioxide was investigated. A hydrophobic gas-permeable membrane separates the gas sample solution from an internal filling solution containing a fixed quantity of chloride ion and a sufficiently large excess of sodium bisulfite so that its concentration may be considered constant. Sulfur dioxide diffuses through the membrane to dissolve in the internal filling solution and liberates an equivalent quantity of hydrogen ions. The electromotive force between a precision-ground, flat-ended pH electrode, which acts as the sensing element, and a chloride sensing electrode, which acts as the reference element, gives a direct measure of S02 in the gas sample solution. Calibration curves in water, tetrachloromercurate (TCM) , and citrate buffer absorption solutions were closely parallel with slopes in their linear segments, ranging from 57 to 52 mv/decade of S02 concentration. The slopes compare reasonably well with the theoretically expected slope of 58 millivolts at 21° C. The water standard curve was linear with respect to the logarithm of S02 concentration from 1 to 1,000 ppm S02; the TCM standard curve was linear from 10 to 2,000 ppm S02; and the citrate standard curve was linear from 30 to 5,000 ppm S02' The high efficiency and nontoxicity of citrate favor it as a substitute for the conventionally used TCM in the absorption solution.

Jan 1, 1976

By Robert W. Smith

The Bureau of Mines is engaged in a systematic evaluation of the thermodynamic properties of combustion gases. These studies are designed to provide basic thermodynamic information of high accuracy, facilitating the theoretical study of flame and combustion phenomena. This report is the fourth of a series4/ presenting results of the study for particular fuel-oxidant systems. These calculations have as their objective the evaluation of the constant pressure flame temperatures of methane-air, propane-air, and ethylene-air mixtures for a range of pressures.

Jan 1, 1953

By A. Wahab Khair, N. P. Reddy

"INTRODUCTION The continuous mining machines which were introduced in the 1950's now account for more than half the production of coal from underground mines. Unfortunately, these continuous miners which were designed for increased productivity have also increased the concentration of respirable dust in mines. Inhalation of this respirable dust by miners causes the Coal Worker's Pneumoconiosis (CWP). Concern for CWP increased in the United States following a 1963-65 survey that showed definite x-ray evidence of CWP in 9.8 percent of working miners and in 18.2 percent of nonworking miners in the Appalachian bituminous coal region (Breslin and Niewiadomski, 1982).One of the major objectives of the Federal Coal Mine Health and Safety Act of 1969 was the prevention of CUP. This law initially limited the daily average exposure of coal miners to 3 mg/m3 of respirable dust. However, following the results of a probabilistic model developed by Jacobsen, et. al. in 1971, the limit was reduced to a mass concentration of 2 mg/m3 unless quartz content exceeds 5 percent, a rare occurrence in mines. Based on x-ray categorization prior to death it is believed that the mass concentration in the respirable fraction is a parameter of primary interest for hygenic evaluation of dust exposure. Morgan, Burgess and Jacobson (1973) suggested that the quantity of inhaled dust, although influential is not the only aspect of exposure which is significant in producing CWP. Miners working in higher rank coal (anthracite) mines are more susceptible to CWP (Morgan, Burgess and Jacobson, 1973). This also confirms the findings of the British (Bennett, Dick and Kaplan, 1979 and Hurley, et. al., 1979) and Germany (Reisner and Rubock, 1977). Based on the cytotoxicological evidence Reisner and Rubock (1979) suggested that when coal properties are similar, increasing quartz and mineral content increases toxicity. David, Ottery and Le Roux (1975) examined that as the severity of the CWP increased the retention of the coal dust content in the pulmonary region remained the same, while that of quartz content increased significantly. Leiteritz, Baur and Bruckman (1971) studied the various components of coal dust and showed that coal particles comprised a smaller fraction of the mass of fine dust than did particles of quartz and minerals. It is ironic that quartz and mineral matter both comprise smaller fractions of the higher rank coal dust (Dodgson, et. al., 1971 and Dwiggins, 1981). Results of a recent research revealed that quartz or any other mineral examined had no strong or consistent effect on the incidence or progress of CWP (Attfield, 1984) while Dodgson, et. al., (1971) concluded that high exposures to minerals such as illite, kaolinite and mica will retard the progress of CWP. Size and shape characteristics are believed to be important in the relationship between mineral particles and health effects (Shedd, Virta and Wylie, 1982)."

Mar 1, 1989

By Martin A. Elliott

The Bureau of Mines began its investigation of the use of Diesel engines underground to provide technical information necessary to assist this development in the United States. It was considered desirable to furnish such assistance because successful European developments/ in this. field had indicated that Diesel mine locomotives might be safer than electric trolley locomotives. The Bureau has recognized for some time the importance of eliminating the hazards associated with underground haulage systems using bare trolley wires. For example, each year 30 to 40 fatalities occur as a result of electrocution by contact with bare trolley wires. In 1943 and 1944, 101 men were killed and extensive property damage occurred as a result of mine fires started by falls of roof grounding the bare trolley wires.

Jan 1, 1948

By William L. Crentz

Pike County in the easternmost portion of Kentucky is one of the major coal-producing areas in the eastern Kentucky coal field. The county contains numerous coal beds, many of which are too thin to support mining. The commercially important beds are usually 4 feet or more thick, but selective mining at some places calls for removal of a much thinner section of the bed. The variation in quality of the beds from place to place and the large number of coal beds make correlation uncertain. Samples were collected from 14 different coal beds, of which the Elkhorn group is by far the most important. In addition to the Upper Elkhorn No. 3, Upper Elkhorn No. 2, Upper Elkhorn No. 1, and Lower Elkhorn beds that comprise the Elkhorn group, the Winifrede, Williamson, and Bingham beds constitute the principal coal deposits in Pike County.

Jan 1, 1952

By John W. Buch

Upon review of German World War II mining practices and equipment for planning coal, the Federal Bureau of Mines initiated research leading to the development of a pneumatic planer for anthracite. The results of tests are reported in this manuscript. It was demonstrated (1) that hard anthracite can be planed and (2) that the design and operating requirements are within the limits of present-day engineering and technology. For hard anthracite, the depth of cut indicated is 4 to 6 inches; with a chain pull of 20 to 40 tons and the speed of planer travel of 18 to 20 feet per minute, a 40-hp. motor will be required for the planer hoist. Compressed-air requirements for the planer will be 250 to 300 c, f, m, at 60 to 70 p. s, i. It was learned that the length of the 4 individual sections of the planer should not exceed that of the individual troughs of the armored chain conveyor (5 feet in this instance); otherwise, bottom coal will be left in synclines, and the planer will override the conveyor at anticlines. Pneumatic pushers should be operated from a separate compressed-air line fitted with a pressure regulator. Results indicate that additional development work is warranted.

Jan 1, 1957

Consumption and intensity of use trends for 12 metals, by industrial end use, were estimated for 1972 through 1982 by the Bureau of Mines and U.S. Department of Commerce. The trends were then forecast through 1993 using standard statistical methods. The intensity of use measure selected is the quantity of metal consumed per constant dollar output of a specific industrial sector. The metals studied were aluminum, chromium, cobalt, copper, lead, manganese, nickel, the platinum-group metals, tin, titanium, tungsten, and zinc. Average annual growth rates for the following 4 of the 12 metals increased from 1972 to 1982 as follows: aluminum, 1.00%; platinum-group metals (consisting of platinum, palladium, and iridium), 8.83%; titanium, 7.82%; and tungsten, 6.09%. Consumption for the remaining eight metals decreased at average annual rates ranging from 0.58% (copper) to 5.37% (manganese).

Jan 1, 1986

By Robert F. Chaiken

The Bureau of Mines is using model ducts lined with coal to study the nature of coal mine fires, their rate of propagation, their influence on ventilation airflows, and their response to sealing and other fire suppression measures. For scale-modeling purposes these studies are being carried out in various size ducts; eventually they will include a full-size mine entry in the Bruceton multiple-entry Experimental Mine. To date, work has been carried out in an insulated 9.l-m-long duct with a 5-cm thickness of coal leaving a 23-by 23-cm square opening for air ventilation. Fire propagation processes in this duct were mainly transient in nature owing to the relatively small length-to-diameter ratio. This report describes the experimental equipment employed and the results obtained to date.

Jan 1, 1979

By R. V. Lundquist

A method was developed by the Federal Bureau of Mines for evaluating viscosity data from slurries obtained in leaching sinters from the lime soda sinter process for extracting alumina from aluminous silicates. The logarithm of the viscosity was observed to be a linear function with time. The slope of the plotted line provides a means for evaluating viscosity behavior in a lime soda sinter blurry and also a means for comparing gelation characteristics directly with other variables in the lime soda sinter process. This report presents one aspect of a continuing study by the Bureau of Mines on methods for treating siliceous aluminum ores. It is one of the many programs of the Bureau concerned with conservation, development, and use of our domestic minerals resources. Previous investigations of lime soda processes, both by the Bureau4-7/ and industrial concerns, have demonstrated that sintered materials containing CaO, Na2O, A1203, and S102 in various combinations exhibit a tendency to gel or set when mixed with water or other extraction solutions. Gelling prevents satisfactory recovery of alumina and in extreme cases prevents operation of an extraction plant.

Jan 1, 1960

By M. E. Tyrrell, J. Koster

This work was undertaken to determine the feasibility of making mixed diborides of two metals directly from the metal oxides , boron carbide and carbon . The diborides (Ti , V ) , B₂ , (Ti , Cb) B₂ , and ( Ti , Ta ) B₂ were prepared in a crucible resistance furnace at 2,100 ° C , and X- ray- diffraction analyses showed each was a homogeneous solid solution containing approximately equal molar contents of the given diborides . The diboride powders were cold - pressed ; sintered to 2,300 ° C , and evaluated for mechanical strength , rate of oxidation , and resistance to molten metals . The diboride ( Ti , Ta ) B₂ exhibited the best mechanical properties ; the diboride ( Ti , Cb ) B₂ , the lowest cumulative rate of oxidation . The mixtures were stable in the presence of molten aluminum and copper but were attacked by molten Ti , Zr , and Cr .

Jan 1, 1964

By M. M. Fine

"INTRODUCTION One of the principal activities of the Bureau of Mines during the recent war was to help to increase the supply of strategic and critical minerals. Fluorite was one of the most critical of the nonmetallic minerals because of the increased demand for it as a flux in basic open-hearth and electric steel furnaces and as a raw material for the production of artificial cryolite used in the aluminum industry. Wartime developments in the technology of hydro-fluoric acid, such as the use of the anhydrous acid as a catalyst in high-octane-gasoline production and the use of organic fluorides as carriers for insecticides, also increased the demand for acid-grade fluorspar. 2/ In 1943 the consumption of acid-grade fluorspar was advancing at a more rapid rate than production and was only slightly less than production during the latter half of the year.The outlook for the postwar market for fluorspar is encouraging. Steel production is expected to remain high until the domestic demand for commodities not manufactured during the war is satisfied. The uses for hydrofluoric acid also are expected to increase under the impetus of war-initiated research. In consideration of these and other factors some authorities predict a new peacetime demand for fluorspar equal to 60 to 75 percent of the war production, 5/ 6/ and others believe that the fluorspar industry will be permanently expanded. 7/"

Dec 1, 1947