Search Documents

By Joan T. May

Federal Bureau of Mines studies showed that some organic amine hydrochlorides can be used as dehydrating agents for producing anhydrous magnesium chloride from hydrates and brines. Laboratory-scale tests showed that double salts are formed by reacting 35 percent magnesium chloride brine or spray-dried magnesium chloride with pyridine hydrochloride. Heating decomposed these double salts to anhydrous magnesium chloride and recycle pyridine hydrochloride. Pyridine hydrochloride also chlorinated any magnesium oxide in the spray-dried magnesium chloride. The anhydrous magnesium chloride obtained by the method described contained less than 0.8 percent oxygen. More than 98 percent of the organic amine hydrochloride was recovered.

Jan 1, 1978

The revised inspection standards or recommendations herein have been prepared for use in Federal inspection of bituminous-coal and lignite mines. They succeed a compilation of similar standards published as Bureau of Mines Information Circular 7268 in December 1943 and employed as a guide in Federal inspections since that time. Important alterations and additions have been made because of changes in mining, practice and temporary shortages of some safety equipment; moreover, several previous standards have been found not generally applicable and have accordingly been deleted. Mining methods and equipment continue to change, and new hazards and new safeguards are introduced. Consequently, these standards are subject to revision from time to time. Questions from the coal-mining industry regarding these standards and suggestions as to changes and additions thereto will be welcomed and considered carefully when the next revision is made. Many constructive criticisms from the mining industry have been considered in preparing this edition.

Jan 1, 1945

By Stephen C. Tadolini

The U.S. Bureau of Mines has developed ultrasonic measurement instrumentation capable of measuring strains and elongations on tensioned and untensioned mine roof bolting systems. This report evaluates the pulsed-phase-lock-loop and pulse-echo systems. The pulse-echo systems measure time of flight of a signal through the bolt. The ultrasonic instrument converts the measurement into elongations or stress. The most recent Bureau instrument development converts travel-time measurements directly into elongation, load, stress, and torque by simple data manipulation from the keyboard. Bolt preparation and instrument calibration are described in detail.

Jan 1, 1990

By M. M. Gilkey

Pegmatites in Colorado occur for 150 miles along the Front Range (eastern-most range of the Rocky Mountains) from Larimer County on the north to Canon City on the south, and west into the Gunnison area. Many of the deposits have been classified. Minerals found in the various dikes include beryl, scrap and possibly punch mica, lithium-bearing minerals, columbite-tantalite, feldspar, and several rare minerals. Pegmatites are abundant in the Crystal Mountain district in Larimer County. About 5 miles south of the Crystal Mountain district and often identified with that district is the Hyatt pegmatite area. The Hyatt Ranch deposit has attracted particular attention because of the comparatively high beryl con-tent of the upper part exposed in opencut workings.

Jan 1, 1960

By Alton Gabriel

During the fall of 1940, J. R. Thoenen of the Mining Division, Bureau of Mines, accompanied by the senior author, surveyed the more important domestic alunite deposits. Although the study was designed primarily as an economic survey, samples from a number of the deposits were collected to investigate the beneficiation of the lower-grade material.

Jan 1, 1942

By Alton Gabriel

During the fall of 1940, J. R. Thoenen of the Mining Division, Bureau of Mines, accompanied by the senior author, surveyed the more important domestic alunite deposits. Although the study was designed primarily as an economic survey, samples from a number of the deposits were collected to investigate the beneficiation of the lower-grade material.

Jan 1, 1942

By Mark P. Meyer

During 1991 through 1993, the U.S. Bureau of Mines (Bureau) -Alaska Field Operations Center (AFOC) in cooperation with the Bureau of Land Management (BLM) -Arctic District Office and the State of Alaska, Division of Geological and Geophysical Surveys (ADGGS), conducted exploration, geological, geochemical, geophysical, mineral resource, and mineral potential investigations in the 6.7 million hectare Colville Mining District (CMD) study area. This mining district study area, located in northern Alaska, includes the Colville River drainage basin as well as 0.35 million hectares of the southern part of the National Petroleum Reserve in Alaska (NPRA). This investigation was conducted as part of the Bureau's continuing Mineral Land Assessment (MLA) mining district program. The Bureau's MLA mining district program is designed to provide reliable and comprehensive mineral resource information that supports mineral resource policy and land use decisions made by Congress and Federal land management agencies.

Jan 1, 2011

By Jeffrey A. Aldinger

This U.S. Bureau of Mines report presents an analysis of surface coal mining accidents involving mobile equipment for the years 1989 through 1991. Mobile equipment is defined as haulage trucks, front-end loaders, bulldozers, scrapers, and road graders. These five pieces of mining equipment accounted for 20 pct of all surface coal mine accidents and 41 pct of the fatalities. The general discussion of these accidents covers the accident causes, the primary activity of the accident victims, and other contributing factors. A more detailed analysis of accidents associated with each piece of mobile equipment is also provided. This report will provide mine managers and mine safety personnel with a better understanding of the hazards associated with mobile mining equipment. It identifies where improvements in mobile equipment safety can be made and those areas requiring additional safety emphasis, such as safety training, work procedure changes, or engineering changes to the equipment or work environment. The analysis was performed by a team of researchers using accident data and narratives provided by the Mine Safety and Health Administration.

Jan 1, 1995

By C. O. Karacan, S. J. Schatzel, W. P. Diamond

In coal mining, longwall mining is a preferred method to maximize production by extracting large blocks of coal that have been outlined with a set of development entries. In U.S. mines, longwall panels are typically 305 m (1,000ft) wide (with a continual trend towards even wider panels), and usually over 3,050 m (10,000ft) in length. The increasing size of longwall panels, while helping to increase coal production, may also increase methane emissions due to the exposure of the mining environment to a larger area of fractured, gas-bearing strata. Thus, understanding the impact of increased panel widths on methane emissions, and designing gob gas ventholes and bleeder systems accordingly, can enhance the safety of the underground workforce by reducing their exposure to potentially explosive accumulations of methane/air mixtures. As part of its mine safety research program, NIOSH’s Pittsburgh Research Laboratory has initiated a reservoir modeling effort to better understand the interaction of the various geotechnical factors influencing gas flow within and to the underground longwall mining environment. A focus of this modeling effort has been 1) the prediction of the incremental amount of methane emissions to be expected due to increasing longwall panel widths, and 2) optimizing gob gas venthole completion practices to capture more of the gas in the subsided strata above longwall panels before it can enter the ventilation system of the underground workplace. The history matching phase of the study has been carried out on a 381-m (1,250ft) wide panel in the Pittsburgh Coalbed. Simulations have also been completed for a 442 m (1,450ft) wide panel to estimate the incremental increase in methane emissions and the performance of current gob gas venthole placement configurations. Additional venthole placement configurations were simulated to investigate options for optimizing methane capture from the subsided strata above the wider longwall panel.

By J. W. Paul, J. N. Geyer

"GENERAL STATEMENTThe purpose of this report, which is the first of a series of three covering mines in the Fairmont district of West Virginia, is to give the result of a' study conducted in seal mines to ascertain the nature of the safeguards employed to prevent injury to the workmen from falls of roof and coal. In presenting the subject matter, consideration must necessarily be given to factors, features, and conditions such as method of mining, timber regulations and practices, supervision and natural conditions; and, for comparative purposes, a certain amount of statistical matter bearing upon the relation of fatalities and injuries to their causes, tonnage produced, men employed, days worked, and time lost.Those features and practices found to promote safe protection are summarized and suggestions made for such additional safeguards and practices as appear to give greater protection against injury from falls of roof or coal.ACKNOWLEDGMENTSThis study of falls of roof and coal in mines in Harrison County has been conducted by the U. S. Bureau of Mines in cooperation with R. M. Lambie, chief of the Mining Department of the State of West Virginia who assigned L. W. Brown, a district mine inspector, to assist in the field work and in the preparation of individual reports on each mine visited in this study. The writers acknowledge the helpful suggestions and cooperation given by these officials, the latter of whom assisted in the field work and prop red most of these sketches for the individual reports which wore submitted to the operator by the chief of the department. Thin report is a summary of the contents of the individual reports heretofore furnished the individual operator."

Aug 1, 1931

By Richard L. Rains

The Bureau of Mines made a study of mines and prospects of the Benton Range RARE II area (No. 5056), Mono County, California in October and November 1980. The study area is west of Owens Valley and 30 mi (40 km) north of Bishop, California. The mineral deposits were evaluated by examination of mines, prospects, and mining claims by the Bureau of Mines. Geological, geochemical, and geophysical studies were conducted by the Geological Survey. The principal mineral commodities of the Benton Range RARE II area are gold and silver but tungsten deposits may also extend into the area. Properties with resources are listed in table 1; their locations are shown on figure 1.

Jan 1, 1982

By Sterling J. Anderson

Through the use of nondestructive testing techniques, the Bureau of Mines is pursuing a goal of improving the efficiency of the rock excava-tion process. Toward this end, 44 laboratory tests were conducted to identify a practical method of monitoring fracture development in rock, as caused by an excavation tool. An acoustic emission CAE) transducer was used to monitor the test samples as they were loaded. The signal from this instrument was recorded in real time along with the radial and axial loads generated by the fracturing device. Through the review of these signals on a common-time base, it was possible to see the relationship between the developing fracture and the loading conditions. As a part of the posttesting investigations, samples that were pletely fractured were sawn and ground to expose the fractures. examination of these samples allowed approximations to be made incom-Visual of the total surface created. Surface area approximations were also made for the completely fractured samples. Quantitative analyses· of the AE signals were conducted for comparisons with the calculated surface areas.

Jan 1, 1987

By Arel B. McMahan

The U.S. Bureau of Mines investigated 21 mines, prospects, and mineralized sites in and adjacent to a 38,713-acre portion of the 255,058-acre Kingston Range Wilderness Study Area in 1983. The study area is 35 miles north of Baker, CA in the Mojave Desert. Mineral deposits in and adjacent to the study area are in altered carbonate rocks intruded by diabase sills near monzonite porphyry contacts. Monzonite porphyry forms the core of the Kingston Range and underlies about 70 percent of the study area. Sedimentary carbonate rocks are exposed in bands on the north and east boundaries and as isolated roof pendants in the southeastern portion of the study area.

Jan 1, 1986

These proceedings consist of papers presented at Bureau of Mines Technology Transfer Seminars in December 1983 for the purpose of disseminating recent advances in mining technology in the area of mine ground control. The Bureau of Mines conducts several of these seminars each year in order to bring the latest results of Bureau research to the attention of the mining industry as quickly as possible.

Jan 1, 1984

By J. B. Rosenbaum

Prolonged laboratory and limited pilot plant tests have shown that the Bureau of Mines buffered S02 -H2S process is capable of removing 95 to 99 percent of the S02 from industrial waste gases. Most of the S02 is converted to elemental sulfur; only about I percent converted to sulfate The process comprises (1) washing the flue gas to remove particulates and S03, (2) absorption of the S02 in citric acid or other carboxylate solution, (3) reaction of the loaded solution with H2S in a closed vessel to precipitate the absorbed S02 as elemental sulfur, and (4) separation of the sulfur from the regenerated solution by oil flotation and melting. Two-thirds of the molten sulfur is converted to H2S for use in the sulfur precipitation step by reacting sulfur vapor with natural gas and steam in the presence of an alumina catalyst. The chemistry and mechanism of the process are described, initial laboratory and pilot plant data are summarized, and second-generation laboratory operation and pilot plant design are reviewed. Preliminary cost estimates are presented for recovering sulfur from copper smelter gas, powerplant flue gas, and Claus plant tail gas.

Jan 1, 1973

By William H. Pomroy

Fire on surface mining equipment is a serious hazard to life and property. The Bureau of Mines, through a program of contract and in-house research, has developed and in-mine demonstrated reasonably priced, reliable automatic fire protection systems to deal with this problem. This report reviews the development and subsequent testing of systems for haulage trucks, front end loaders, coal augers, dozers, drills, and shovels. A variety of fire sensors, extinguishing agents, and control systems arc discussed in the context of mine equipment designs and operating environments

Jan 1, 1980

By T. Bajpayee, J. Ellenberger

Microseismic monitoring and evaluation is one aspect of the National Institute for Occupational Safety and Health (NIOSH) research program. Roof falls are often preceded by a period of elevated microseismic activity, but not all periods of elevated activity result in a roof fall, nor do all roof falls occur after some amount of elevated activity. The objective of this study is to review periods of elevated microseismic activity and determine whether fracture activity rate can be used to anticipate the initiation of roof falls. The study was carried out at an underground limestone mine where major roof falls are associated with excessive horizontal stress. The progression of roof falls was detected by the microseismic signature produced by the rock falling from the mine roof onto the mine floor, which is termed a roof fall impact event. A total of nine elevated fracture activity periods that resulted in seven major roof falls were examined. It was observed that elevated fracture activity preceded the initial roof fall impact event in three out of four major roof falls. The initial impact event was not identified for the remaining three roof falls. Fracture event rates were analyzed and a roof fall alarm trigger of five fracture events in a ten minute time period was established for this test case. The fall alarm trigger was tested against six of the elevated activity periods. Four roof falls occurred in the six periods of elevated activity, and two would have triggered the alarm before the roof fall occurred, while two false alarms were generated. The results show that limited success would have been achieved by the microseismic system as a roof fall alarm trigger. However, the trigger would have been successful at warning of the onset of elevated activity, allowing mine employees to respond appropriately. The study highlighted some issues with implementing such a system in an operating mine, including the need for real time identification of fracture related microseismic signals among mining induced signals, and accurate location and identification of fracture clustering.

By R. H. Grau, S. B. Robertson, R. B. Krog, T. P. Mucho

Due to the difficulties of ventilating large opening stone mines, the effective dilution of diesel particulate matter and noxious gases has often been problematic. Since stone mines have large openings that develop low air resistances, and propeller fans are designed for low pressure-high volume applications, main mine propeller fans may be a feasible option for ventilating underground stone mines. This paper describes the results of a case study where researchers from the National Institute for Occupational Safety and Health have demonstrated that significant increases in total mine airflow can be achieved and the ventilation improved in a large-opening stone mine by replacing an axial-vane mine fan with two 12-ft diameter propeller fans and adding a line of stoppings. In this study, the use of the propeller fans more than doubled the air quantity from 300,000 cfm to 750,000 cfm, while operating at 50 horsepower less than the original axial-vane fan.

By Stephen C. Tadolini, Peter (Yunqing) Zhang

A unique circumstance created by monitoring a pre-driven longwall recovery room permitted measuring the stresses of a coal pillar throughout its entire life cycle in less than a week. A fender pillar, created in approximately the middle of a longwall panel at a depth of 650 ft, transformed from a solid barrier pillar - to a yielding pillar - to a residual pillar as 3 ft slices were methodically removed with the longwall shearer. The complete transformation, or life cycle, took place in less than 12 hours. The stresses were quickly transferred from the pillar onto the standing pumpable concrete supports and into the outby pillars. Roof to floor closure measurements, combined with the timing of the pillar behavior, provides a detailed look at the uncontrollable convergence of underground mine openings. Pillars remain the most important form of “primary support” and understanding these life cycles is vital for safe and efficient mine design, in both room and pillar and longwall panel extractions.

By R. Karl Zipf, Suresh Bhatt

Highwall mining is an important coal mining method. It appears that upwards of 60 highwall miners are presently in operation, and they may account for approximately 4% of total U.S. coal production. A review of the Mines Safety and Health Administration (MSHA) data over the 20 year period from 1983 to 2002 identified 9 fatalities attributable to auger and highwall mining of which inadequate ground control accounted for 1/3. In the past 5 years, 1 fatality occurred in highwall mining. Estimates of the manpower requirements in highwall mining suggest that its fatality rate is essentially the same as for surface coal mining, thus highwall mining appears to be a very safe modern mining method. Highwall stability is the major ground control related safety concern, and operators are required to develop and follow an appropriate highwall mining ground control plan. The plans usually specify the following geotechnical parameters: hole width, maximum hole depth, maximum overburden depth, seam thickness, web pillar width, barrier pillar width and number of holes between barriers. Calculated web pillar stability factor exceeded 1.3 for most designs evaluated. This study examined records from 5,289 highwall miner holes with a total completed footage of about 2,560,000 feet to understand the reasons for early pull out. Average lost footage is typically about 20% of planned footage. Only 35% of the holes reached planned depth, and 20% were short due to rockfalls. Water and adverse geology accounted for 15% of the losses. Mechanical/electrical problems, guidance, and slope stability problems accounted for the remaining 30%. Web pillar stability factor for these holes also exceeded 1.3 in 95% of cases. Best practices to avoid trapped miners include: avoid mining in stream valleys, avoid mining near outside corners, careful alignment of each hole and the use of an onboard guidance system. Several issues in highwall mining ground control require further investigation including highwall mining through old auger workings, highwall mining near old underground mines, multiple-seam and multiple lift highwall mining and finally the size and frequency of barrier pillars.