Search Documents

By J. A. Organiscak

Quartz dust is one of the most significant ongoing health concerns in coal mining today. Since the early 1980's, the U.S. Bureau of Mines has conducted numerous studies in underground and surface coal mines to identify the sources of quartz dust and its fundamental characteristics. This report presents data and conclusions obtained from these studies. The two most significant quartz dust sources were found to be the continuous miner excavating rock and the highwall drill operating in a rock overburden. The percentage of quartz was found to be higher in the smaller size fractions of dust when significant amounts of rock were mined by the continuous miner. Another factor theorized to affect quartz dust generation and size characteristics is the morphology of the quartz-bearing rock. Several laboratory studies were conducted to investigate capture efficiency of water spray technology and flooded-bed scrubbers with respect to the particle size of the dust. Water sprays and flooded-bed scrubbers were both found to be less efficient on smaller dust particles, and the scrubber was particularly less efficient on quartz dust. These results indicate that quartz control technology should be directed at controlling smaller sized dust particles.

Jan 1, 1990

By J. W. Adams

Measurements of surface magnetic field noise were made at various locations over the Geneva Coal Mine near Price, Utah, on June 12, 1973. The locations selected were on the surface over emergency locator beacons underground at depths between 3S0 meters (1150 ft.) and 488 meters (1600 ft.). The surface terrain where these measurements were made was mountainous, and access was difficult. There were no power lines within several miles, and the weather was clear; therefore, the magnetic noise levels were about as low as will normally occur. Results of measurements of distant sferics indicate rather sharp cutoff frequencies below which broadband, impulsive noise is attenuated. The mechanism of propagation for this noise above the daytime cutoff frequency of 3500 Hz and the nighttime cutoff frequency of 1700 Hz is deduced to be a waveguide formed by the D or F layers of ionosphere as an upper plane and the earth as a lower plane.

Jan 1, 1974

By L. B. Pankratz

Enthalpies above 298° K were determined for AgCl to 1,400° K and for AgBr to 1,200° K by copper-block calorimetry. Before melting, both compounds showed an anomalous increase in enthalpy, an effect associated with lattice defect formation. Melting points and heats of fusion were determined to be AgCl, 730° K and 2,945 cal/mole; AgBr, 700° K and 2,030 cal/mole. The heat capacity of both melted substances decreased with increasing temperature over the entire liquid ranges investigated. Enthalpies above 298° K were tabulated at even temperatures along with derived entropy increments and heat capacity values. The results were combined with the known heats of formation and entropies at 29.8.15° K to obtain values of the heats and free energies of formation over the range 298.15° to 1,400° K for AgC1 and 298.15° to 1,200° K for AgBr.

Jan 1, 1970

By J. K. Whyatt

The U.S. Bureau of Mines conducted an overcore stress measurement on the 5300 level of the Lucky Friday Mine, Mullan, ID, to investigate the stress regime around an experimental stope in a rock-burst-prone mine. The result indicated a stress field with unexpected magnitude and orientation [s 1 ?135 MPa (19,600 psi) oriented S 80° W). An unusual amount of rock-burst activity was encountered during subsequent excavation. A careful review of the overcore data suggested the overcore strain measurements were valid. Moreover, concentrated rock-burst activity suggested that the measured stress field did exist, but was localized and therefore did not represent the far-field in situ stress field.

Jan 1, 2010

By Alla D. Mah

The heats of combustion of three chromium carbides, Cr23C6, Cr7C3, and Cr3C2, were determined by combustion calorimetry. Heats of formation calculated from the results follow: ?Hf°298 (Cr23C6) = -94.7 ± 5.0 kcal/mole, ?Hf°298 (Cr7C3) = -43.3 ± 1.7 kcal/mole, and ?Hf°298 (Cr3C2) = -22.5 ± 0.8 kcal/mole.

Jan 1, 1969

By Daniel E. Sullivan

The recession of 1974 continued into 1975. Real gross national product (GNP), measured in 1972 dollars, declined significantly in the first quarter of 1975 but rose slightly in the second and increased sharply in the third quarter. Unemployment peaked during the second quarter and then declined slowly for the balance of the year. The inflation rate declined owing to reduced demand and smaller-than-1974 increases in energy and food prices early in the year. Recovery was clearly evident by yearend, though un-employment and inflation remained at high levels. Total output as measured by the GNP in current dollars rose 6.5% in 1975. Real GNP declined 2.0%, and inflation, as measured by the implicit price deflator, increased 8.7%. Real gross private domestic investment for residential structures declined 18.1% in 1975, which was a smaller rate of decrease than the 27% decline in 1974. Real State and local Government purchases increased 2.4%, and real personal consumption expenditures for services rose 1. 7 %. The Federal Reserve Board (FRB) index of industrial production declined 9.7%.

Jan 1, 1977

By D. A. Buckingham

The Bureau of Mines evaluated potential availability of domestic nickel from 23 deposits, Evaluations included an estimation of in situ and recoverable resources, applicable mining and processing technologies, and capital and operating costs. Discounted cash flow analysis with a 15-pct rate of return was used to determine the average total cost of production of each operation, Identified in situ resources contain 9.0 million metric tons (t) of nickel; 5.5 million t is recoverable as nickel metal or ferronickel. Demonstrated in situ resources contain 8.2 million t of nickel; 4.8 million t is recoverable as nickel metal or ferronickel. No nickel is available at a total cost of production equal to the January 1983 market price of $3.24 per pound. Analyses indicate that potential annual production can only meet current consumption levels at a total cost of production of $7.60 per pound of nickel, Nickel's availability is contingent on (1) successful adaptability of nickel processing methods to domestic resources, (2) location of a smelting facility, and (3) marketability of byproducts and coproducts. Analyses were performed on the effects of byproduct and coproduct revenues, energy, labor, and transportation costs, and metallurgical recoveries on nickel's availability.

Jan 1, 1984

By Peter K. Mathison

The U.S. Bureau of Mines has developed a hydrologic monitoring system for in situ leaching operations. This system records and displays flow and pressure information from sensors located in leachant injection and recovery wells. Continuous monitoring of hydrologic conditions is important during leaching operations because hydrologic factors such as aquifer permeability, solution injection rates, injection pressure, and solution recovery rates interact and change over time. This hydrologic monitoring system has been tested in an underground setting at the Cyprus Casa Grande copper mine. The system consists of hardware and computer software components and includes two Bureau-developed software applications. This publication describes the implementation of the hydrologic monitoring system and the software developed at the Bureau in support of in situ leaching research.

Jan 1, 1994

By A. C. Fieldner

In preparing this paper, an attempt was made to obtain results of plant-scale carbonization tests on washed and unwashed coal from the same mine. A letter. in which the following questions were asked was sent to some 50 coke-oven superintendents and others who might be interested; "What is the influence of washing coal on: (1) The chemical and physical properties of coke, as for example, the size the amount of breeze, the fracture, strength, cell-structure, etc. (2) The quantity and quality of gas and by-products. (3) The capacity of the ovens. (4) The composition of the coal. "Your general opinion, as well as any specific data or results of tests, on this important subject will be arc greatly appreciated."

Jan 1, 1930

By F. S. Crawford

Interesting data on electric blasting and sinking of the Montreal No. 5 shaft of the Montreal Mining Co., Montreal, Wis., were obtained during the sinking of the last 877 feet of this shaft. Several unusual features and safety practices are also to be found in the Montreal mine. The Montreal shaft was sunk 2,156 feet from August 16, 1921, to May 1, 1924, and 877 feet from October, 1927, to June, 1928. The first section of the shaft was supported with steel sets spaced 5 feet on centers; and instead of lagging the walls were covered with three-eighths of an inch of gunite where Greenstone was encountered, and where quartz-slate was found (from the surface to the 12th level) the walls were lagged with tamarack lath treated with carbolineum, a preservative.

Jan 1, 1929

To improve the level of hearing protection by providing workers with an inexpensive, easy-to-use device to check earplug fit. Background Approximately 30 million workers are exposed to hazardous noise on the job, placing them at risk of permanent hearing loss, tinnitus, and other disorders. Although the preferred solution is to eliminate noise through engineering controls or to reduce noise exposure through administrative controls, hearing protectors are critical when noise is unavoidable. Studies of hearing protector users have shown that average protection values in the real world are much lower than the labeled noise reduction ratings determined in laboratories with trained and motivated subjects. Even worse, many hearing pro­tector users get virtually no protection at all because of poor fit. The studies also show that users have a harder time achieving adequate protection levels with earplugs than with earmuffs. It?s difficult for users to tell if earplugs are working well just by looking at them. A more accurate approach is to check how much they block or ?attenuate? noise. Earplugs vary in their attenuation characteristics, with most providing a maximum of 20?35 decibels of noise reduction when worn correctly. Any earplug that?s suitable for use in noisy settings will attenuate noise by at least 15 decibels. Personal fit testing is an effective way to help hearing protector users improve the fit and protection levels of the devices. However, existing fit-testing systems are expensive and unsuitable for use at many industrial worksites.

Dec 1, 2008

By Alphonso Cornejo, Galen H. Clevenger

This bibliography was compiled in connection with an investigation of the Caron process for the treatment of manganese - silver ores , conducted by the T. S. Bureau of Mines in cooperation with the Netherlands East Indies Government . The object of this investigation was to develop a practicable method for treating the refractory manganese- silver ores found in these two countries . The results of the work will be published as a bulletin of the Bureau of Mines . This bibliography summarizes the available information on the subject previous to the investigative work embodied in the forthcoming bulletin, and may be useful to those metallurgists or others conducting work along this line .

Mar 1, 1923

By Theodore Kessler

The purpose of this Bureau of Mines investigation was to determine what new organic compounds or high concentrations of a particular organic species can be formed by exposure of coal derivatives to ultrasonic energy. Tetralin, l-methylnaphthalene, and pyridine were used as model compounds. Gaseous and solid reaction products resulting from the ultrasonic irradiation of these coal derivatives were determined using mass spectrometry. Products from the irradiation of tetralin were studied as a function of time, atmosphere, and sample size. The sonolysis (chemical reactions produced by ultrasonic energy) of tetralin and l-methylnaphthalene produced C2H2, HCN, CH4, H2, CO, and CO2, depending upon the experimental conditions. The ultrasonic irradiation of tetralin also produced diacetylene under certain experimental conditions. The cleavage of organic chemical bonds by ultrasonic cavitation in the absence of water was also observed in this study.

Jan 1, 1967

By William R. Roy

Seven coal-related waste samples (mining, cleaning, and gasification) were characterized chemically and mineralogically. Laboratory extracts of each sample, using a variety of different extraction methods, were used in both acute and chronic bioassays. A coal slurry sample (coarse fraction) and two coal cleaning refuse samples were chemically and mineralogically similar, and generated acidic water-waste systems, both in the laboratory and in the field. Acidic laboratory extracts and field samples of acid mine drainage in the area where the solid samples were collected, tended to be in equilibrium with some type of CaSO4 phase and with maghemite. The chemical composition of the extracts was sensitive to the method used to generate the extracts, but generally had the same prevalent chemical character as the field samples. The acidic wastes contain appreciable quantities of soluble Al, Mn, Ni, SO4, and Zn as indicated by both laboratory extraction and field data. Long-term extractions suggest that some constituents (Al, Fe, SO4) continued to be released by the acidic wastes after 22 weeks with no apparent associated change in pH. Two mine spoil samples, essentially shale, tended to generate water-waste systems that were neutral in pH and consequently released lower quantities tit potential pollutants than the acid wastes. The gasification residue was compositionally similar to coal-fired power plant slag and fly ash and generated moderately alkaline extracts with low concentration of soluble potentially toxic constituents. All of the solid wastes contained a variety of organic compounds, many of which are on the EPA Priority Pollutant List. However, these compounds were essentially insoluble in aqueous media. Each extract was tested for acute toxicity with tour species of freshwater aquatic organisms; green sunfish (Lepomis cyanellus), fathead minnow (Pimephales promelas), a crustacean (Daphnia magna), and a snail (Physa anatina). The extracts of the two mine spoil samples and of the gasification residue were not toxic to any of the organisms while the extracts from the acidic refuse and slurry samples were acutely toxic to all of the organisms. For all cases, pH was significantly correlated to mortality while Al, Fe, Mn, Ni, and Zn were significantly correlated to mortality in specific instances. Data from 96-hour LC-50 determinations showed that dilutions up to 1:1000 were necessary to eliminate mortality. The most toxic extracts were those with the lowest pH which necessitated the largest amounts of dilution to eliminate mortality. Chronic bioassays with the same test organisms were investigated with leachate samples from a relatively unweathered refuse sample and an older, more weathered refuse sample. The unweathered refuse sample generated a leachate that was acutely toxic while the leachate from the weathered refuse sample was not acutely toxic. No detrimental chronic effects were noted in organisms exposed to dilutions of the non-toxic leachate while low concentrations of the acutely toxic leachate produced lower hatchability for the Lepomis cyanellus and Pimephales promelas eggs, increased mortality with chronic exposure for Lepomis cyanellus, Daphnia, Physa, and reduced weight gain for Physa. Dilutions of a toxic, high-Fe leachate resulted in the precipitation of ferric hydroxide that was implicated as the major causative factor accounting for the physical and physiological toxic effects exhibited by all of the test organisms in these acutely sublethal concentrations. The toxicity of this leachate demonstrates the potential effects that these types of wastes can have on the aquatic ecosystem if they enter a receiving water in a natural setting.

Jan 1, 1984

By J. J. Sammarco

Light emitting diodes (LEDs) are emerging as viable replacements for incandescent-based cap lamps used in mining. The photometric and energy characteristics of these light sources differ in important ways. The present paper describes the performance of LED and incandescent sources in cap lamps in terms of correlated color temperature, color rendering, light output, electric power, ambient temperature and airflow, and light source aging. Importantly, these characteristics can influence a miner?s ability to spot mining hazards thus impacting safety. Secondly, some of these characteristics interact with the operating life of the cap lamp?s battery power, such that differences between LED and incandescent sources can be magnified toward the end of a 10­hour battery discharge cycle. Empirically, we have determined that after 8 hours at an ambient temperature of 25 °C, the average light output of an incandescent cap lamp can decrease to about 69% of its initial value when powered by a lead-acid battery and it can decrease to about 65% of its initial value when powered by a nickel-hydride battery. An LED-based cap lamp using a constant current drive circuit can maintain about 96% of its initial value when powered by a nickel-hydride battery. Real-world tests addressing the effects of ambient temperature and airflow on the light output of an LED and incandescent cap lamp were conducted in the NIOSH Safety Research Coal Mine (SRCM). The LED cap lamp yielded a vertical average illuminance improvement of approximately 9.5% and the INC cap lamp yielded a vertical average illuminance degradation o f approximately 4%. The differences between LED and incandescent cap lamps were further quantified by the calculation of ?mesopic luminance? data that indicated for the same photopic luminance (i.e., as measured using a conventional light meter) the LED cap lamp could be up to 38 % more efficient than the incandescent cap lamp with a lead-acid battery at the end of the 10-hour driving cycle. Lastly, accelerated life tests were used to empirically determine light output depreciation as the incandescent light source age approached its useful life. There was about a 35% decrease in light output. This is quite considerable, especially given that the light output will decrease an additional 30% to 45% over the period of a 10-hour shift. The implications of the differences between LED and incandescent sources are discussed. This information is crucial in determining how visual performance could be affected for real-world conditions where batteries discharge during the work shift and as the light source ages. To date, only idealized conditions have been used for LED and incandescent cap lamp visual performance research.

Jan 1, 2008

By Mary S. Esfandiary

U.S. scientists attempting to maintain continuous surveillance of scientific information are confronted with two acute problems: The steady, even spectacular; increase in the volume of such information and the fact that much of it is published in unfamiliar foreign languages, According to the National Science Foundation, almost one-third of the world's scientific literature is published in languages that are read by less than 5 percent of U.S. scientists. Most scientists in the United States must rely on abstract journals and translations to obtain information on developments in research and investigations conducted in the non-English-speaking countries. However, there are problems involved in procuring suitable abstracts and translations and in obtaining such information as cheaply and rapidly as possible.

Jan 1, 1961

By Frank J. Wiebelt

Under a general program to extend the resources of mineral deposits, the Bureau of Mines examined the Quien Sabe antimony mine in October 1948. The preliminary evaluation demonstrated that a diamond-drill program was warranted co establish the tenor and persistence of the veins and permit an estimation of antimony reserves. The Bureau of Mines conducted a diamond-drilling program on the property from December 1949 to May 1950. Ten holes aggregating 2,483 feet were drilled. Nine of the holes encountered antimony-bearing vein material.

Jan 1, 1956

By John A. Burgess

The Carson Hill mine of the Carson Hill Gold Mining Corporation is at Melones, Calaveras County, Calif. It is one of the numerous mines on the Mother Lode of California. The property extends for 8,400 feet along the outcrop of that important vein system. The elevation at the haulage level is about 1,000 feet above sea level. ACKNOWLEDGMENTS Acknowledgment of assistance in the preparation of this paper is made to Frank Wagner, underground superintendent; Max Petersen, engineer; and Homer Mann, assistant engineer. The geology of the Mother Lode has been described by Adolph Knopf in Professional Paper 157 of the United States Geological Survey; references to general geology have been abstracted largely from Knopf.

Jan 1, 1937

By Mayer G. Hansen

A series of papers dealing with diamond drilling practices, compiled in accordance with an outline prepared by engineers of the United States Bureau of Mines, is to be published as information circulars by the bureau. This paper, the first of the series, describes the general practice at the United Verde mine during the last ten years; specific instances cited in the paper refer to 1930, the last year of full operation. The United Verde copper mine is located at the town of Jerome, Yavapai County, north central Arizona.

Jan 1, 1933

By Thomas L. Ochs

The Bureau of Mines is investigating the fundamental behavior of electric arcs in electric furnace operations. The electric arc is a poorly understood phenomenon. If the arc in a steelmaking furnace can be more carefully controlled, it should be possible to increase heat transfer to the melt, reducing both electrical and acoustical noise. As a first step toward a better understanding of the are, voltage and current signals from operating furnaces were analyzed. The results of the initial analysis show that instrumentation used in monitoring and controlling furnaces, such as meters and strip-chart recorders, gives incomplete or erroneous information to the operator and therefore leads to less than optimal control. Advanced instrumentation and analysis techniques, such as the waveform analysis used in these investigations, can improve the understanding of operation and the control of electric furnaces. This report describes the instrumentation and the numerical analysis methods used and compares these methods with standard metering and recording techniques.

Jan 1, 1986