Search Documents

By Robert J. Evans

The Hopper-Feeder-Bolter (HFB) is a prototype multifunctional machine designed to improve productivity by minimizing continuous miner place changes. It is designed primarily to work beside a two-pass continuous miner, bolting on one side and then place changing to bolt the other side while simultaneously providing a surge car and lump breaker located directly behind the continuous miner. Surface testing was conducted at the Bureau of Mines Mine Equipment Test Facility (METF) to evaluate overall system performance and reliability. Tests were conducted to evaluate place changing, tramming, lump breaking, roof bolting, drawbar pull, conveying, temporary roof-support (TRS) capacity, lighting, and noise. Surface test results indicate the HFB is ready to be tested and evaluated underground in a production mode.

Jan 1, 1988

By Stephen W. Lambert

The Bureau of Mines examined the wellbore of a vertical gas drainage well in the Mary Lee coalbed to determine the results of specific completion procedures in coal. A jet-slotting tool was used to cut four vertical slots through the casing about 1 ft below the coalbed. Even though stimulation treatment pressure was excessive, hydraulically induced channels were contained entirely within the target coal zone. Sand-filled, induced channels were horizontal, inclined, and vertical, and were propagated in directions similar to bedding planes, rock joint, and coal cleat directions measured in the mine. Variable gas flow rates, recorded during the productive life of the well, were attributed to chronic downhole pump malfunction and the slotted casing below the production zone.

Jan 1, 1978

By Heinz W. Sternberg

The literature on electrochemical treatment of coal is reviewed, and possible avenues of further research in this field are discussed in this report. Electrolytic reduction of finely distributed coal resulted in the addition of as many as 9 atoms of hydrogen to 100 atoms of carbon. Reduction of coal extracts at controlled potentials indicated the presence of condensed aromatic hydrocarbons and reducible quinones in coal. As much as 65 percent of low-rank coal can be made alkali soluble by electrochemical treatment. Higher rank coals gave smaller yields of alkali-soluble products. However, the nature of this reaction is not clear. The difficulty of reducing coal electrolytically is probably due to the insolubility of coal and not to any structural peculiarity. Reduction of coal by electrolytically generated radical anions appears to be a promising approach for further research.

Jan 1, 1962

By J. G. Donaldson

A bench-scale method for recovering lead and zinc from slimes and mill tailings from the Tri-State District of Missouri, Oklahoma, and Kansas was developed by the Bureau of Mines. Dilute hydrochloric acid, containing sodium chloride, and chlorine gas were used to decompose the mineral constituents. Lead was electrolyzed from the pregnant acid solution, and zinc was precipitated from the depleted electrolyte by neutralization with lime. Up to 98 percent of the lead was recovered in an impure lead electro- deposit assaying approximately 85 percent lead. Zinc recoveries up to 90 percent of the total were attained in a precipitate assaying approximately 40 percent zinc.

Jan 1, 1963

By Kevin Malone

Chrysotile asbestos occurs in many counties in California, and a small production had been reported at times, but development of deposits had been disappointing. A reconnaissance survey by the Bureau of Mines indicated that several deposits in the serpentine belt in Shasta, Trinity, and Siskiyou Counties might contain enough asbestos of filler grade to supply the growing demand on the west coast. Accordingly from 1956 to 1958 parts of the Mount Eddy and Shasta View deposits were investigated by trenching and diamond drilling to determine their potential. The work comprised construction of roads, bulldozer trenching, excavation of areas for diamond drilling, sampling, and upping. The trenches were excavated to expose the surface extent of some of the asbestos-bearing areas, To determine the downward continuation of asbestos-bearing sections and to secure samples for test purposes, six diamond drill holes, totaling 1,738 linear feet, were drilled in two selected areas. The trenching and core-drilling indicated that the asbestos-bearing material occurs as ribs and lenses of varying thicknesses in a broad belt of serpentine, about 600 feet wide and several miles long,

Jan 1, 1962

By Elizabeth A. Johnson

The vaporization thermodynamics of the aluminum-silicon carbides Al4SiC4 and Al8SiC7 were studied by the Bureau of Mines over the temperature range of approximately 1,500 to 1,700 K. Vapor pressures were measured by a Knudsen effusion-mass spectrometry technique in which powdered samples were effused from graphite crucibles through small orifices. For each compound, a total of six orifice diameters was tested to verify equilibrium within the cell. Aluminum, mass number 27, was the only vapor species detected over the range 4 to 200 amu. Experimental results are based on the following equations for incongruent decomposition: A14SiC4(cr) - 4A1(g) + SiC(a,hex) + 3C(gr); Al8SiC7(cr) - 8A1(g) + SiC(a,hex) + 6C(gr). The observed vapor pressure-temperature relationships determined with a cell orifice area of 2.0 x 10-3 cm2 for Al4SiC4 and 1.81 x 10-3 cm2 for A18SiC7 are the following: Log P - (-18,682/T) + 12.476, for Al4SiC4 (1,550 to 1,643 K) and Log P = (-19,308/T) + 12.421, for Al8SiC7 (1,526 to 1,784 K), with P in pascals and T in kelvins. Third-law analysis of the data provided the following heats of formation: A14SiC4 ?H at 298.15 K - -50.0 kcal/mol and A18SiC7 ?H at 298.15 K - -92.1 kcal/mol.

Jan 1, 2011

By M. R. Geer

This report presents the results of washability examinations of seven coals from the principal coal-producing fields of Montana. A complete performance test of the Baum-type jig operated at one of the mines is included, as are the results of cleaning tests made on two of the coals in a dense-medium pilot plant. The coals examined from the Red Lodge, Bull Mountain, and Forsyth fields are comparatively easy to clean. Ash contents of 5 to 10 percent can be obtained at yields of washed coal ranging from 90 to 95 percent. The coal from the Great Falls field, however, could not be cleaned readily to less than 14 percent ash, and the rejection of impurity would amount to over 25 percent. The two coals treated in the dense-medium pilot plant were characterized by sharp separation of impurity, high recovery efficiency, and satisfactory reduction in ash content.

Jan 1, 1955

By Michael Hood

High-volume, low-pressure water jets have been employed for erosion of loosely consolidated rocks for centuries. This excavation method finds application in specialized circumstances even today. The use of high-pressure, low-volume water jets for rock cutting is more recent and was made possible by the development of high-pressure water pumps. Despite the benefits often claimed for these systems, high-pressure water jets still have not found widespread application. In this report, the U.S. Bureau of Mines has reviewed the various methods that have been employed using water jets to break rock and has focused on one method, termed "jet-assisted cutting," which was determined to be the closest to commercial development. The current state of knowledge based on laboratory and field experiences using this cutting method is reviewed, and possible future developments for this approach to excavation are assessed.

Jan 1, 1990

By W. H. Coghill

Numerous investigators have studied grinding. Each has contributed his bit to a literature that is difficult to correlate. Too many of the results have been transformed into curves with so many "inflection points" and "counterflexures" that they obscure the issue. Some of the investigators have neglected the very essence of the problem, namely the power and the amount of material to which a known amount of work was applied. The purpose of this paper is to show the ease with which results can be interpreted when these quantities are duly recognized. Some grinding tests will be given for illustration. Grinding studies are of two kinds: (1) Study of the character of the ore and (2) study of the performance of the machines. Several ores may be crushed by a given machine, or several machines may be used on a given ore. The illustrations given in this report cover both objectives.

Jan 1, 1934

By Geoffrey G. Huggins

Discussions are presented of the three phases of the noise reduction program on flight-type coal conveyors. The three phases are identification of noise sources, evaluation of potential noise reduction concepts, and implementation of noise reduction which is intended to reduce conveyor noise to less than 90 dB(A) in the underground mining environment. The major noise sources are impacts of the chain on the tail roller and on the top and bottom decks. A total noise reduction of 11 dB(A) was achieved by using techniques which are applicable to retrofit. These are a vibration isolated tail roller and an isolated wear strip on the return deck. A theoretical model of isolation provided by the isolated tail roller is developed. Appendices are presented which contain information on other potential concepts and additional data generated.

Jan 1, 1976

By H. F. Yancey

The Baum-type jig used so widely to clean bituminous coals has not been adopted for anthracite. If proved suitable for anthracite, its use might lower preparation costs in some plants. Cleaning trials on a Pennsylvania anthracite in a laboratory-size Baum-type jig were undertaken by the Bureau of Mines to provide indicative information that would be helpful in determining whether the cost of a full-scale installation would be justified. Clean coal surpassing standard anthracite specifications was obtained in all sizes from Stove through No. 5 Buckwheat. Recovery effi¬ciencies were acceptable down to 3/16-inch size, but there was excessive loss of coal in the finer sizes. Thus the fine refuse produced in a commercial plant might re¬quire retreatment. A comparative cleaning trial in a dense-medium pilot plant provided a recovery efficiency only l percent higher than obtained in jigging.

Jan 1, 1957

By John W. Frey

Although there are certain general uniform provisions in the laws ... of the several Provinces of Canada the differences are so great that it is considered advisable to present digests of separate mining laws rather than a digest of Canadian mining law as an entity . This analysis , accordingly , has been divided as follows : Nova Scotia , New Brunswick , Quebec , Ontario , British Columbia , and a group of Provinces under Dominion Law .

Sep 1, 1930

By A. H. Roberson, F. S. Wartman

For many years , it has been the common practice at most copper mines to recover copper in solution in effluent mine water by precipitating the copper with scrap iron.4/ The technique employed varies from simply throwing scrap iron or tin cans into the waste ditches to passing the water through elaborate launder systems containing detinned scrap and baled cans . In general , a considerable amount of low - cost copper has been recovered that otherwise would have been lost . Iron consumption usually varies from 1 to 1-1/2 pounds of iron for each pound of copper recovered . The grade of the precipitate may be as much as 90 percent copper.4/ ,5/ Where the consumption of iron is materially greater , its cost is likely to be the determining factor of profit . In times of emergency, when the demand for scrap iron for remelting increases the cost of the iron sharply, and the supply of tin cans is not large enough to meet requirements , recovery of the copper might not be economical . The three principal reactions that take place when an acid mine water containing iron and copper salts in solution is brought into contact with metallic iron are : (1 ) Copper is precipitated and an equivalent amount of iron is dissolved , CuSO4 + Fe Cu + FeSO4 ; ( 2) ferric salts are reduced to ferrous salts , Fe2 (SO4 ) 3 + Fe = 3FeSO4 ; and (3) the free acid in the solution reacts. with metallic iron to produce ferrous sulfate , H2SO4 + Fe = H2 + FeSO4 . = Because of the reported high.consumption of iron (5 to 6 pounds per pound of copper precipitated ), when copper in water from the Hornet mine of the Mountain Copper Co. ( California ) was precipitated upon scrap iron , a series of tests was made to determine . the . optimum treatment, time , and consumption of iron .

Feb 1, 1944

By M. M. Kirk

Forced-air cooling of cold-mold arc furnaces for melting zirconium and similar metals has been investigated and found to be practical from the stand-point of heat transfer. It is believed that this technique offers a significant reduction in explosion hazard from that inherent in water cooling, the current industrial practice. A copper crucible, with longitudinal, integral-type fins and with an outer jacket to confine the airstream, appears to be the best general design for air-cooled operation. Cutting the fins into short segments and bending the segments to produce a herringbone effect increased the airstream's turbulence and was found, on test, to increase the heat transfer up to 35 percent.

Jan 1, 1959

By E. H. Denny

This paper discusses accident experience and costs in 150 Colorado coal mines for the 5 years 1929-33; these mines produced 62 percent of Colorado's coal tonnage during this period. This and similar studies by the United states Bureau of Mines in other States (listed in the appendix to this report) make available comparable information on mine-accident costs and bring out clearly the importance of accident reduction from the humanitarian as well as from the economic standpoint. Compensation insurance costs constitute a considerable part of the cost of coal output. The tendency toward greater liberalization of workmen's compensation laws and increased benefits thereunder may mitigate to some extent the seriousness of an accident to a worker and his dependents, but no compensation is paid ultimately, not by an insurance fund but by the mine operator and the general public, which includes the miner. The one really effective method of reducing compensation costs is to reduce the number and severity of accidents.

Jan 1, 1935

By W. L. Crentz

Before Korea was partitioned along the 38th parallel following World War II, the coal fields of South Korea, with the possible exception of the Samchok area, were not considered important to the industrial needs or Japan or Korea. Much of the demand for electric power in South Korea was met by hydroelectric installations north of the 38th parallel. Following cessation of hostilities between Japan and the' Allied nations in 1945, hydroelectric power continued to flow into South Korea from the north until 1949, when the North Koreans severed the power lines into South Korea, thereby forcing that section of the country to depend almost entirely upon coal to generate electric power.

Jan 1, 1953

By Leland E. Paulson

This investigation examined the feasibility of altering the inorganic component of North Dakota lignite by ion exchange. Lignite of specific size consist was washed with various ionic solutions and examined for evidence of exchange. Ions of higher valance substituted preferentially at equivalent concentrations. Results indicate that a major portion of the inorganic material associated with lignite is combined in exchangeable form with the organic component. Particle size of the treated coal is a critical factor in determining the rate of exchange. The data indicate that monovalent ions are easily replaced by divalent and trivalent ions, and the presence of ionic material in slurries containing finely divided lignite significantly increases filtration rates.

Jan 1, 1968

By James P. McGee

Use of nuclear reactors to furnish high-temperature heat is a field that has not received as much attention as propulsion and electric power production. Investigations are being conducted under a joint Atomic Energy Commission (AEC)--Bureau of Mines research program to determine the feasibility of using nuclear heat for chemical processing. A part of this process-heat-reactor program is the study of a system in [hich] helium transfers heat from 8 nuclear reactor to a chemical processing [essel]. This requires construction of (1) a nuclear reactor to operate with helium exit temperature of 2,500° F. and with pressures in the range of 250 to 500 p.s.i.g. and (2) a processing vessel (heat exchanger) to convert the enthalpy of the helium into chemical process reaction heat. Neither component exists at present, and development of each promises to be a formidable task. To aid in the study of such a system, the Bureau of Mines has designed and constructed a vessel heated by electrical induction to simulate a source of nuclear fission heat. This vessel is undergoing preliminary testing. Gasification of coal and reforming of hydrocarbons are promising uses for nuclear heat. It appears that a higher price per unit of nuclear heat can be tolerated for chemical processing than that allowable for power generation.

Jan 1, 1960

By L. M. Demers, R. E. Edelson, M. P. Rose, D. T. Superdock

The pulmonary alveolar macrophage is a major defensive cell which counteracts the invasive properties of bacteria and particles when these substances invade the pulmonary environment. Pulmonary exposure to coal dust particles is believed to activate these macrophages to release a host of d1emical mediators which can neutralize or contribute to the harmful effects of these dust particles. Our efforts have been concerned with assessing a specific family of mediator substances produced by the alveolar macrophage from arachidonic acid when these cells are in contact with activating substances such as coal dust. Metabolites of arachidonic acid produce a vast array of effects which can impact significantly on pulmonary function both with normal pulmonary events and with pathologic processes of the lung. Our studies demonstrate that isolated alveolar macrophages obtained from rats or guinea pigs cultured in vitro release appreciable amounts of the cyclooxygenase products prostaglandin E2 and thromboxane A2 and release significant amounts of the lipoxygenase products .5-HETE and LTB4. In the presence of l x 104 -1x10·7 g/ml of a coal dust suspension, alveolar macrophages from the rats and guinea pigs alters their pattern of arachidonic acid metabolite release. In the rat, exposure of alveolar macrophages in vitro to the higher concentrations of coal dust causes a significant reduction in PGE2, TXB2 and LTB4 in a 4 hour time course study. In contrast, macrophages from the guinea pig in response to coal dust had little change in TXB2 release, only a slight inhibition in PGE2 production and an initial stimulation in LTB.t release over the 4 hour time course. Cells from guinea pigs released considerably more TXB2 than the rat under these conditions while rat cells formed considerably more LTB4 than guinea pig alveolar macrophages. These findings support the following conclusions.

Mar 1, 1989

By Robert J. Timko

Because of leakage through and around permanent stoppings in underground mines, more air must be forced into a mine than would otherwise be required for ventilation. As power costs increase, costs resulting from air leakage add increasingly to the operating costs of mining. The Bureau of Mines evaluated four different stopping construction techniques based on the ideas that (1) airtightness could be enhanced by brushing rather than troweling on mortar sealant and that (2) modified mortars (mortars containing glass fibers and other additives for increased strength and adhesion) would improve sealing performance. Air leakage tests comparing conventional to modified stoppings were done when the stoppings were built, after 6 months, after 1 yr, and following simple maintenance. It was found that stoppings can be built and maintained better if-- The area where a stopping is to be built is properly prepared. Stoppings are constructed using the techniques devised by the Bureau. Stoppings are periodically examined for leaks. Stoppings found to be leaking, especially at the perimeters, are resealed.

Jan 1, 1983