Search Documents

By James Spiers

This paper describing the mining practice at the Central-Eureka mine is one of a series of similar papers being prepared by the United Staten Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. The mining practices described in this paper are illustrative of the methods employed in the exploitation of comparatively low-grade gold ores under the extremely heavy and swelling ground conditions which occur in the Mother Lode belt of California. The Central-Eureka Mining Co. comprises a group of adjoining mines in Amador County near Sutter Creek. The principal mines of the consolidated group are the Central-Eureka, formerly known as the Summit mine, and the Old Eureka mine, which is also known as the Hayward Quartz mine. The group is situated in the most productive part of tae main Mother Lode belt, the 10-mile portion which lies between the towns of Plymouth and Jackson. The three largest producing mines of the entire belt at the present time are the Argonaut, Kennedy, and the Central-Eureka; these lie within a radius of less than 1-1/2 miles.

Jan 1, 1931

By L. C. Brichta

During a study of the Badger-Peacock area from October 1950 to June 1953, the Federal Geological Survey and the Federal Bureau of Mines completed nearly 98 miles of resistivity profiling and drilled 96 test holes aggregating 17,628 feet of bore, In addition, seismic profile measurements were made along 8 traverse lines for an aggregate length of about 16,600 feet. The geophysical surveys were conducted by the Geophysics Branch of the Geological Survey; the drilling was done by the Bureau of Mines. Electrical-resistivity measurements disclosed 21 low-resistivity anomalies and 1 high-resistivity anomaly. Correlation of the resistivity data with the geological information revealed by the drilling disclosed that the low-resistivity anomalies indicated either slumped shale deposits in limestone sinks or undisturbed deposits of shale lying in erosional depressions in the limestone. The high-resistivity anomaly indicated hard, undisturbed limestone at or near the surface.

Jan 1, 1958

By Charles A. Seitz

This Bureau of Mines report describes a chromatographic method for analyzing impurities in helium that utilizes a helium carrier gas contain-ing 25 to 30 ppm Ne. An example of the effect of trace amounts of nitrogen, methane, and moisture on the detector's response is shown. The added neon in the carrier does away with irregularities of the analysis which were experienced when the carrier contained up to 3 ppm Ne. The addition of 25 to 30 ppm Ne causes a loss of sensitivity, but the re-maining sensitivity is adequate for routine analyses. The high-neon carrier allows positive and more linear responses for eight impurities: neon, hydrogen, argon, oxygen, nitrogen, methane, carbon dioxide, and ethane. Neon concentration levels of 0.02 to 125 ppm in helium carrier gases were studied. The high-neon carrier has been in successful rou-tine use in Bureau of Mines helium facilities since October 1981.

Jan 1, 1985

By J. H. Field

Synthesis of hydrocarbons by the Fischer-Tropsch reaction in a hot-gas- recycle system was demonstrated to be technically feasible. This project was undertaken, by the Bureau of Mines, to determine if the system was operable and to ascertain the optimum conditions for the production of gasoline. Carbon steel turnings packed with a void volume from 88 to 90 pct. were satisfactory catalysts, but steel catalysts with greater void volume, either turnings or steel wool, were not as active. Good temperature control with a pressure drop of less than 0.5 pounds per square inch (p.s,i,) per foot of catalyst bed of turnings was obtained by operating with a recycle to fresh feed ratio of 20 and by splitting the total gas flaw and injecting portions into the reactor at different entry ports.

Jan 1, 1961

By Ginger S. Evans

This report documents a preliminary hydrologic investigation of an area where longwall mining methods are to be used. The scope of work includes: determination of physical and chemical characteristics of major soil types in the area; determination of physical and chemical properties of surface water bodies; collection of geologic characteristics, including stratigraphy, structure, and detailed aquifer descriptions; collection of 10 years' meteorological data and installation of a weather station; and a detailed ground-water investigation that includes completion of observation wells, aquifer testing, water quality sampling, and analysis using a 3-D computer model. The Trescott model developed by USGS was used to simulate steady-state aquifer conditions. Input data from 8 multiple-completion monitor wells were used to model an area of approximately 10 square miles. Two layers, coal and overburden, were simulated, both confined. Model results showed good agreement with know piezometric data, desaturated areas, and flow from springs. The study area was found to have very low-yield bedrock aquifers with transmissivities ranging from 5 to 320 ft2/day for the coal (depths from 500 to 1,200 ft) and from 499 to 576 ft2/day and fractured sandstone units (depths less than 100 ft). Annual precipitation and recharge are very low, 10 to 11 inches and 0.25 inch respectively. The area has very high relief and large areas of rock outcrop. No perennial streams are present on the site.

Jan 1, 1983

By Paul M. Tyler

"In preparing this paper the writer has perforce depended mainly upon published information, including the catalogs and pamphlets issued by importers and dealers such as the Diamond Drill Carbon Co. and J. K. Smit & Zonen. Special acknowledgment is made to various articles published by S. H. Ball. The writer of this paper, however, is alone responsible for statements herein contained and since he has often found it necessary to rationalize apparently conflicting opinions of recognized authorities on this little-known subject, he will welcome constructive criticism from the trade.Two types of diamond are extensively used for industrial purposes. One type, known as bort or bortz (boort, boart, bowr, etc.), consists of diamonds of the gem variety but unfit for cutting into gems. They may be colorless, yellow, brown, or gray. The other type, carbonado, known in the trade as ""carbon"" or ""black diamond,"" differs greatly from the white diamond, being opaque and apparently amorphous or noncrystalline. Actually, instead of forming a large single crystal as in a gem stone, carbon diamond comprises a mass of microscopic crystals that interlock to form a tough, homogeneous material with no planes of cleavage. It is found in various colors -- black, dark green, brown, and gray -- but usually it has .a dark lustrous black surface, with a resinoid or submetallic appearance, often resembling fine-grained steel. Upon exposure to the air the broken surface gradually darkens to an ash-gray color. Ballas is a special type of carbonado in which the crystals are definitely-oriented around a central nucleus. They are harder and tougher than ordinary carbonado but are much scarcer. The Cape ballas is reputed to be not quite so tough as Brazilian ballas but tougher than carbon or bort.The diamond crystals are isometric and take a variety of forms. The cleavage is octahedral and well marked. A crack is easily -started parallel to an octahedral face, and bort or gem diamonds are notoriously brittle, especially when subjected to sudden shock. Even carbonado, while it has a high resistance to slowly applied pressures, may be chipped or broken by a sharp blow.Exposed to radioactive rays, the diamond becomes phosphorescent; this property is often utilized to distinguish it from quartz, topaz, or glass. The unusually high refractive index likewise aids in its identification in the case of a more or less transparent stone. At the temperature of the electric arc, diamond is converted into graphite, another form of Carbon but one of the softest mineral substances. At a much lower temperature, as low as 1,5620 F., the diamond may be burned like ordinary carbon in an atmosphere of oxygen, and according to some authorities there is danger of burning a diamond if overheated even in air."

Mar 1, 1932

By Albert E. Long

During the summer and fall of 1948 the Bureau of Mines, in cooperation with the U. S. Geological Survey, conducted 6xperiments in diamond core drilling in the Phosphoria formation in southeastern Idaho and southwestern Wyoming. Nearly all of the diamond core drilling in the Phosphoria formation has been done by mining companies interested in finding and developing phosphate-bearing beds amenable to stripping. The recovery of sludge; and enough core (usually 30 to 60 percent) to identify certain marker beds produced by current drilling practices meets both the primary requirement of mining companies in determining depth of overburden and their secondary need to determine the phosphate content of relatively thick minable units whose general composition and nature are already fairly well established.

Jan 1, 1949

By Robert Bottge

When a company develops a mineral property in a remote area of Alaska, it must consider how best to house its personnel. This Bureau of Mines report examines the economics of two options: company towns and company camps. The price required to maintain a 15% discounted-cash-flow rate of return (DCFROR) was derived for hypothetical 1,000-st/d cut-and-fill mines and 50,000-st/d open-pit mines located in three different regions of the State, One set of hypothetical mines utilizes a townsite; the other utilizes a relatively new concept, a fly-in camp or commuting operation, in which two shifts of employees operate the mine and all associated facilities for 1 week before being replaced by a second crew. The study shows that operating costs were higher for mines employing the commuting option than for mines having a company town because of the additional wages paid for overtime hours; however, the price required to obtain a 15% DCFROR for the single-product copper concentrate, f.0.b. the mill site, was significantly lower owing to the lower investment costs for the camp-type operation. The economic advantage for those mines utilizing the camp increases from south to north and from the coast toward the interior.

Jan 1, 1986

By C. Q. Cupps, R. F. Zaffarano, J. Fry

Reservoir oil analyses from seven wells in the Greater Clareton area have been included in a study of the original characteristics of oil in the Newcastle sandstone reservoir . These data correlated with areal location of the wells show an increase of saturation pressure in a general north - south or downdip direction . The increase amounts to about 500 psi in more than 17 miles , which corresponds to a depth increase of about 1,600 feet . To facilitate application of the data to engineering analyses , average characteristics are given for arbitrary north and south divisions of the 22 - mile - long producing area . The downdip increase of saturation pressure is taken as evidence of updip diffusion of solution gas from a somewhat higher concentration at the bottom of the reservoir . This effect is opposite to that previously observed in two prominent high- relief reservoirs in the Rocky Mountain area . The increasingly greater saturation pressures southward or downdip in the Greater Clareton area suggest a continuing migration of fluids into the structure .

Jan 1, 1964

By William J. Krisko

This contract final report summarizes the design, fabrication and testing of a "line brattice air curtain" device under Bureau of Mines Contract H0357097. The purpose of this program was to develop the concept of using an air curtain for coursing ventilating air parallel with the air curtain From the last open crosscut to the face in exhausting ventilation systems to replace the line brattice cloth in room and pillar coal mining operations. The final design of the air curtain device consists of a 10-foot long closed end pipe with c: slot cut along its length. Pressurized air is delivered to the open end with a hydraulically-driven blower. A sheet of air emanates from the slot and is directed toward the mine roof. An invisible sheet of air is thus created between the top of the machine and mine roof and acts a an extension of the existing conventional line brattice.

Jan 1, 1977

By D. Harrington

As no cure is known for silicocis after it has developed, prevention is the only effective remedy. There are two main lines of approach to the problem of dust-disease prevention in industry - the engineering, through control of dust production, and the medical, through selection of workers by examination; success probably depends upon a combination of the two. Hatch (146) considers the following measures essential to a complete, well-balanced program of control of the dust hazard in industry: 1. Selection of workers by means of physical examinations in order especially to eliminate those with tuberculosis and other disorders of the respiratory system. 2. Reduction of the duct concentration below the standard of permissible dustiness through adequate moans of dust control and good housekeeping. 3. Limiting the frequency and duration of employment in the dusty occupations, thus reducing the rate of deposition of dust in the lungs. 4. Routine measurement of the effectiveness of the dust-control program by means of periodic medical examinations and duct surveys.

Jan 1, 1935

By William S. Roberts

The Bureau of Mines has initiated a program to determine the availability of land for mineral exploration and development in Alaska. Researchers involved in this pro-gram are comparing land availability, based on ownership and government policies and regulations, to the distribution of known mineral deposits and terranes. This report on southeastern Alaska presents the findings of the first of six regional studies that will cover the State. The study consisted largely of data compilation and analysis using various mapping techniques. Summary land availability data are presented on copies of U.S. Geological Survey (USGS) quadrangles at a scale of 1:500,000. Five categories of land availability were identified: open to mineral exploration and development (approximately 9.4 million acres, or 38% of the 24.8-million-acre study area), open but with possible use restrictions (4.2 million acres, or 17%), selected (0.5 million acres, or 2%), patented (0.74 million acres, or 3%), and formally closed to mineral exploration and development (10 million acres, or 40%). Of the 1,187 known mineral deposits in the study area, approximately 38% are on land in the open category. Mineral terranes comprise approximately 6.7 million acres, or 27% of southeastern Alaska. Approximately 34% of these terranes are on open land.

Jan 1, 1985

By L. H. McGuire, L. B. Berger

"During the period October 31 to November 4, 1944, tests were conducted by the Bureau of Mines in the Cascade Tunnel of the Great Northern Railway Cc. to determine the effects upon the tunnel atmosphere of the use of a Diesel freight locomotive through the tunnel. These tests were conducted at the request of the company to ascertain whether undesirable conditions might be caused by the discharge of Diesel engine exhaust gas in the tunnel, which was constructed for an electric haulage system and is not provided with equipment for mechanical ventilation. The use of Diesel locomotives on the division that includes the Cascade Tunnel was under consideration as a means of augmenting haulage facilities for the abnormal freight tonnage that must be handled during wartime.As the Bureau of Mines has received requests for information on the extent of contamination of the air of railroad tunnels by Diesel locomotives, this report was prepared to make available for general information the data obtained during the tests in the Cascade Tunnel. As the test locomotive is of a type used on other railroads, and as the bore and grade of the tunnel and the tonnages moved are comparable to such factors on other roads, the data should be sufficiently representative to be of general interest. The exceptional length of the Cascade Tunnel made it an excellent location for obtaining information on the composition of the tunnel air and on the movement of air induced in the tunnel by the passage of trains.The writers are indebted to C. O. Jenks, vice president of the Great Northern Railway Co., who arranged for the tests, and to the following personnel of the railroad who cooperated in the conduct of the tests: I. E. Clary, superintendent, Spokane Division, J. L. Robson, superintendent of motive power, oil and gas equipment, J. F. N. Gaynor, superintendent of electric operations, William Lowney, master mechanic, Spokane Division, and D. F. Marston and Verne Nelson, assistant superintendents of electric operations.The Cascade Tunnel is on the Spokane Division of the Great Northern Railway and pierces the Cascade Mountains some 49 miles west of Wenatchee, Wash. The west end of this division is electrified from Appleyard Station, 2 miles east of Wenatchee, to Skykomish, Wash., a distance of 73 miles. Until the described tests, only electric haulage had been employed through the tunnel since it was first opened to traffic in January 1929.The Cascade is the longest railroad tunnel in the United States - 7.79 miles. The tunnel is single-track, perfectly straight, concrete-lined, and is on an essentially uniform grade of 1.56 percent, ascending from west to east. The cross-sectional area of the tunnel is 314 square feet, the dimensions being shown in figure 1. Elevation of the east portal is 2,880 feet and of the west portal, 2,240 feet."

Jun 1, 1946

By John M. Gomes

A two-phase molten halide-silicate technique for extracting tungstic oxide (WO3) from scheelite (CaW04) and wolframite [(Fe, Mn)W04] was investigated. The halide phase extracted over 99 percent of the was, whereas the lower silicate phase retained about 90 percent of the calcium, iron, or manganese oxides. The most efficient extraction and separation of tungsten from scheelite was accomplished at 1,080° C in a molten system containing, in mole-percent, 9 calcium tungstate (CaW04), 42 sodium chloride (NaCl), 28 sodium fluoride (NaF), 17 sodium metasilicate (Na2SiO3), and 4 alumina (Al2O3). Wolframite was also treated at 1,0800°C; the molten system contained, in mole-percent, 11 (Fe, Mn)W04, 74 NaCl, and 15 Na2 SiO3.

Jan 1, 1968

By Daniel G. Di Canio

A computer based accident cost indicator model (ACIM) for estimating tangible costs of occupational injuries, illnesses, and fatalities in the U.S. mining industry is described. Studies performed to expand the scope of the ACIM to all mining sectors are presented. Validation of ACIM cost element estimation algorithms with actual costs of mining-related injuries and illnesses are presented. A study of the effect of a fatal accident on production in surface coal and metal/nonmetal mines is presented. The study is based on a sample of 15 fatalities in underground and surface mines. Evidence of significant long- term decline in postfatality production at 6 of 8 underground samples is presented. The average loss is shown to be 1.8% of annual mine production. A study of accident costs in U.S. mining from 1975 through 1981 using the ACIM is presented. The study shows that total annual costs increased from $180,000,000 in 1975 to $379,000,000 in 1981, a 15% annual increase after adjusting for inflation, with mining companies bearing 45% of the total and expected wage losses to mining families accounting for 42%. The study shows total costs of $12,400 per accident and $674,000 per fatal accident for 1981.

Jan 1, 1983

By G. W. Jones

Explosion hazards that may exist when air becomes polluted with combustible gases and vapors are extremely dangerous, particularly if the volume of gaseous atmosphere is large, and an explosion under such circumstances could do tremendous damage to persons and property. The hazard is even greater if explosive mixtures are confined under high pressure, as the pressure could increase to tremendous proportions just before the container would rupture. Because of its interest in safety in the mining and allied industries, the Federal Bureau of Mines has investigated the flammability (explosibility) of various types of combustible atmospheres and published its findings. The explosibility of natural gas has been studied, and the limits of flammability have been determined and published. Other investigations have shown how explosions of natural gas-air mixtures may be prevented by the addition of nitrogen and carbon dioxide.

Jan 1, 1949

By E. G. Davis

The Bureau of Mines made laboratory-scale experiments to examine the technical possibilities of reclaiming manganese from slags produced by oxygen lancing of high-manganese pig iron. Ferromanganese was added to molten pig iron to yield a 4-to 5-percent manganese hot metal, which simulated a product obtainable from the blast furnace. This was injected with oxygen to reduce the metal to 1 percent or less manganese and form a slag containing about 40 percent manganese. The molten slag was water-quenched, treated with H2SO4) roasted at 660° C, and water-leached to give soluble manganese and iron sulfates. The sulfates were precipitated as hydroxides, converted to the oxide form, and smelted to produce a standard ferromanganese containing 74.6 percent Mn and 0.01 percent P. As an alternate method of manganese recovery, a manganese cell feed was prepared from the leach solutions and electrolytic manganese was produced. Direct smelting of the high-manganese slag resulted in 74.2 ferromanganese meeting ASTM specifications except for phosphorus content. The high phosphorus content of the metal and high slag-to-metal ratio obtained made this approach unattractive.

Jan 1, 1966

By R. O. Dannenberg

The Bureau of Mines investigations described in this report were undertaken to devise a process to economically recover precious metals and copper from low-grade, complex electronic scrap generated in large quantities by military and civilian electronic operations. Leaching with various media is applicable to certain selected items of electronic scrap but cannot be practically applied to complex mixtures of scrap. A process comprising incineration, caustic leaching to remove aluminum, smelting with a siliceous slag, and electrolysis recovered 99.9-percent-pure copper metal and anode slimes assaying more than 7,000 ounces per ton of combined precious metals. Silver, gold, and copper recoveries were 93, 95, and 87 percent, respectively. Cost analysis indicated that an alternative process using direct smelting of the scrap to make assayable products for sale to a custom smelter would provide better overall financial returns.

Jan 1, 1972

By H. R. Wells

The Blackbird district, Lemhi County, Idaho, has long been recognized as a potential source of cobalt and copper. However, the comparatively low grade and small size of the known ore bodies, the small demand for cobalt, and. the lack of adequate roads throughout the region precluded extensive exploration of the early discoveries in the area. Recent advances in alloy metallurgy, accentuated by wartime activities, greatly increased the demand for sources of domestic cobalt. Beginning In 1941, engineers of the Bureau of Mines conducted an examination and exploration program in the Blackbird district. This work was supplemented by an exploration program by engineers of the Howe Sound Mining Co., 730 Fifth Ave., New York 19, N.Y.

Jan 1, 1948

By R. L. Grayson, L. L. Probert

"A three-year project focusing on the depth profiling of respirable coal mine dust particles using scanning electron microscopy coupled with energy dispersive X-ray analysis resulted in the development of statistically classified particle-behavior models. The models depict the changing silicon fraction for particles at 5-, 7-, 9-, and 11-keV accelerating voltages, thereby giving a clear indication of the nature of various types of mineral particles. This paper focuses on the results for respirable quartz particles sampled from five underground coal mines across the US. Through statistical analysis of results the relationship between the fraction of surface available quartz in respirable dust samples and coal rank is established for three Pennsylvania coal seams. IntroductionThis is the last in a series of papers detailing the results of SEM/EDX-based analyses of respirable coal mine dust particles collected from field sampling. Previous papers have detailed preliminary results and the statistical validity of the methodology (Grayson, Andre, and Simonyi, 1990; Grayson, 1991). This paper presents the final results of the analysis of respirable dusts from five coal seams with a range of coal rank:• Lykens Valley seam (anthracite), eastern Pennsylvania• Brookville (A) seam (mid-vol bituminous), central Pennsylvania• Pittsburgh seam (high-vol B bituminous), western Pennsylvania• No. 6 seam (high-vol C bituminous), Illinois• Wadge seam (sub-bituminous A), ColoradoSEM/EDX-based techniques were applied to try to clarify the role of quartz as an etiologic agent in coal workers' pneumoconiosis (CWP). It was hypothesized that previous studies were hampered by the restrictions of bulk analysis techniques and that particle-level analyses were needed to answer a number of questions concerning the role of quartz in CWP and its progression.Since 1985, a large number of the respirable dust samples submitted to MSHA are analyzed for free silica (Tomb, Parobeck, and Gero, 1986). Our reasearch shows that conventional bulk analysis techniques may not give a true indication of the biologically available, or active, quartz in mine dusts. Analytical evidence indicates that respirable dust samples may contain many quartz particles that are occluded, or coated, resulting in a bulk analysis for ""free silica"" that may not be indicative of the biologically available quartz surface."

Dec 1, 1996