Search Documents

By J. R. Thoenen

This paper outlines briefly results of seismic measurements recorded in the vicinity of quarry blasting under practical operating conditions. The data cover field work done from January to the middle of August 1930, during which time records were made of 61 blasts in 19 quarries. Of the tests made, one was in biotite-gneiss, two in dolomite, two in a flintlike volcanic complex, three in gabbrodiorite, five in trap rock, and six in limestone. One quarry was in Alabama, two were in South Carolina, two in New York, four in Kentucky, five in Connecticut, and five in Massachusetts. Explosive charges ranged from 0.30 pound to 41,900 pounds, and the method of shooting varied from mud caps through hammer and wagon drill holes to churn drill holes and coyote tunnel shots.

Jan 1, 1937

By G. L. Oldright

In the first paper of this series (R. 1. 4333) on the cooperative work with the Eagle-Pitcher Mining & Smelting Co., changes in the nature of the sinter feed were measured by corresponding changes in the retorting temperatures necessary to distill zinc at the best rates; the firing schedules summarized such changes. In this paper, third of the series, are noted same of the changes in practice that were brought about by the need to treat more fused, glassy, and "hard" sinter, as the operators qualify it. Losses of uncondensed zinc were increased by adding zinc-bearing materials from which? the zinc was readily distillable to hard sinter requiring higher-temperatures for zinc distillation. The rates of zinc distillation were increased by grinding the fuel finer; there were few benefits and loss of dust on grinding the sinter finer, unless the fine ?coal and fine sinter were brought into contact by pelletizing, and the pellets made but little dust.

Jan 1, 1948

By W. P. Yant

This report describes result of a study of the carbon monoxide and particulate matter in the air of the Holland, Tunnel and metropolitan New York made by the Bureau of Mines (which had participated in the development

Jan 1, 1941

By R. L. Grant

During the last decade or more , experimental research on commercial detonators used for initiating the detonation of dynamite and other high explosives has led to important improvements . Developments , especially in the United States , have been directed toward improvement in the construction of detonators to make them safer to manufacture and use . More suitable and safer initiating charges also have been found . Although for many years mercury fulminate was unrivaled as the initiating charge for dynamite , during the last decade it has been replaced to a large extent by less sensitive , more efficient, and cheaper combinations of ignition , priming , and base charges . Commercial detonators were once of relatively simple construction and almost universally identical . Today they are technically complex, with special nodifications for particular uses ; they have developed along different lines n various countries and even among the several manufacturers within any one country .

Apr 1, 1943

By A. G. Loomis

Although secondary-recovery methods have not been applied widely in California, it is apparent that increasing attention and effort must be given to this phase of recovery if the State is to maintain its high rank as a petroleum producer. Steadily increasing demands for petroleum products and decreasing rates of discovery of new oil fields and rapid depletion of existing reserves emphasize the prospect of an adverse situation of supply and demand in the not-far-distant future. If the trend of discoveries becomes more favorable or if more complete economic recovery of the oil in place can be obtained by secondary recovery, this situation can be averted. Not only are these reserves of economic importance to the petroleum industry to meet increasing market demands, but economic reclamation of such reserves is an important conservation measure, which will prolong the productive life of many fields" Accordingly, progressive operators in California are alert to the possibilities of secondary recovery and have done much to implement such operations wherever feasible. Most of the operations are of the pressure-maintenance type} in which the reservoir pressure is maintained or partly maintained by injecting natural gas to increase oil recovery. The possibilities of recovering additional oil from stripper fields by gas drive and water flooding (including water disposal) also are being tested in experimental field projects. Table 1 summarizes gas and water-injection projects in California.

Jan 1, 1952

This publication contains four papers presented at a seminar on mine subsidence control held in Pittsburgh, PA, on September 19, 1985. The seminar was designed to keep the mineral industry informed of new technology developed by the Bureau of Mines that permits reliable and accurate prediction of mine subsidence. The papers describe actual field studies undertaken by the Bureau to monitor surface subsidence over longwall panels. Topics discussed include the efects of subsidence on water table levels, the development of subsidence pre calculation methodology suitable for use with the specific lithological conditions of the Pittsburgh coalbed, an engineering comparison of technologies used in surveying for longwall mine subsidence, and a comparison of the process of subsidence over two different longwall panels.

Jan 1, 1985

By E. O. Binyon

"Corundum and andalusite were discovered in August 1944 on what is now known as the Blue Metal group of claims. The property, comprising five unpatented lode claims, is situated 20 Miles northwest of Yerington in the Buckskin Mining District, Douglas County, Nevada, An engineer of the. Bureau of nines examined the property on November 1, 1944, and recommended a small: amount of drifting and crosscutting to determine more definitely the extent and character of the ore deposit. The work that had been done by the owners was for sampling purposes only and was confined to a few small pits on the outcrop, and no effort had been made. to delimit the ore zone. Samples taken from the best surface showings were sent to the experimental station in Salt Lake City for beneficiation tests. The results of the preliminary test work appeared favorable, and upon the strength of them and the recommendations made by the Bureau, 2.5 miles of access road was approved and completed early in 1945. Exploration was started on June 24 and completed September 26, 1945.In its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mines resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director.This paper is one of many reporting on various aspects of the Bureau of Mines program initiated in August 1939 by passage of the Strategic Minerals act, the scope of which was. greatly expanded by subsequent legislation.Some of these papers were published as war minerals reports, others as bulletins, technical papers, reports of investigations, and information circulars of the Bureau of Mines or• in, technical journals.The Bureau's program at first included separate investigations by the Mining and metallurgical Divisions, but these were consolidated under Assistant Director R. S. Dean beginning July 1, 1942. Mining and metallurgical investigations carried on in three regional organizations more closely integrated thereafter by a staff of specialists, who reviewed findings made in the field and in Bureau Laboratories, considered proposals for additional work, revised reports for publication, and served as advisors to the assistant director."

Aug 1, 1946

By Matthew N. Plis

This U.S. Bureau of Mines report presents the documentation for COALVAL, a coal property evaluation software package developed on Lotus 1-2-3,4 version 2.2, spreadsheets. The software is compatible with version 3.1 as well, and may provisionally be run on the earlier 2.01 version. COALVAL is a menu-driven program that produces a prefeasibility-level cost analysis of mine-planned coal resources. The package contains cost models for each of five coal mining methods commonly employed in Appalachia: auger, contour strip, mountain top removal, continuous miner, and longwall. Other models, such as a dragline cost model, will be incorporated as the Bureau's Coal Recoverability Program matures. COALVAL allows mine operators, evaluators, consultants, and Government entities to input resource data and the various production, operating, and cost variables that pertain to their property. The program can evaluate up to 25 seams, each to be mined with up to five different mining methods, within a given area. Summary spreadsheets listing the cost per clean ton to mine the resources, f.o.b. the tipple, are produced for each property, seam, and mining method/seam combination.

Jan 1, 1993

By A. G. Loomis

METHODS for measuring relative permeability as a valid function of saturation were compared by the. Bureau of Mines, using core samples from representative oil-productive California formations, from the Bartlesville sand in Oklahoma, and from synthetic samples. Measurements for gas-oil systems were made by steady-state dynamic, unsteady-state displacement and two stationary-phase methods. Measurements for water-oil systems were made by the unsteady-state displacement method. As the ratio rather than individual relative permeabilities is measured by the last method, three methods for calculating individual relative permeabilites from their measured ratio were compared for gas-oil systems and two methods for water-oil systems. Errors arising from capillary discontinuities, such as the end effect and stabilized-zone flow, are discussed and evaluated; possible errors rocs arising from turbulant flow are also examined. The inapplicability of non-steady-state methods for water-oil systems that are not definitely oil-wet is discussed in detail. Measurements of relative permeability to both gas and oil can be made quickly and accurately by the steady-state dynamic method when rates of flow of the two phases are sufficient to minimize the capillary discontinuity at the outflow end of the sample. At such rates relative permeability-saturation measurements are essentially independent of the rate of flow. The steady-state method wits modified by a dispersion section at the inflow end of the sample acid designated tie dispersed-feed method.

Jan 1, 1962

By Leo A. Schrider

A prediction for oil recovery from a pilot waterflood in the Kane oil- field, located in Elk, Forest, and McKean Counties, Pa., was made and compared to actual field performance. Water-injection and production histories, well logs, other field data, and results from laboratory tests of core material were used in this analysis. Performance of the pilot waterflood, initiated in January 1963, was predicted using a modified Craig, Geffen, and Morse calculation technique. Maximum recovery from this low permeable, preferentially oil-wet formation was predicted to be about 22,500 barrels of oil after 300,000 barrels of water had been injected into the pilot waterflood area. After additional field data were collected it became necessary to reevaluate the pilot waterflood area. The gas saturation prior to the waterflood was estimated to have been 20 percent, based on an assumption regarding the required volume of water injected to initiate oil production. In view of the actual field performance, a gas saturation of 13 percent is indicated. When this gas saturation and the method originally proposed by Craig and others are used) the predicted results are more representative. In December 1965, field performance was further analyzed using a hyperbolic-decline curve as presented by Arps. Based upon this evaluation method, the pilot water flood in the Kane sand should produce 37,000 to 42,000 barrels of oil with the injection of 300,000 barrels of water into the pattern. By continuing this secondary-recovery project to a reasonable economic limit, ultimate oil recovery may be as much as 50,000 to 55,000 barrels, or 129 to 142 barrels per acre-foot from 36.5 acres.

Jan 1, 1967

By Stephen M. Jasinski

The development and industry adaptation of advanced technologies have led to many important uses for bismuth and its compounds. Bismuth-base alloys are essential for manufacturing jet engine turbine blades, lenses, and various safety devices, such as fire-protection sprinklers. The addition of bismuth to iron, steel, and aluminum imparts properties to these metals that makes them useful in diversified applications. Bismuth is also used widely in medicine, pigments, and electronics. The United States relies heavily upon imports from South America and Europe to meet its demand for bismuth, which is recovered chiefly as a byproduct of lead processing.

Jan 1, 1992

By Jeffrey A. Shibe

A prototype Fire Safety Evaluation System has been developed and is ready to be evaluated by a Peer Consulting Panel and for performing field tests. The system can be used to determine combinations of widely accepted fire safety equipment and under-ground coal mine features that provide a level of safety equivalent to those required by the Code of Federal Regulations-Title 30 for underground coal mines. In this evaluation, equivalent safety performance is gauged in terms of overall level of safety provided rather than by a component by component comparison.

Jan 1, 1987

By Michael Rieber

This study is an extension of our previous work in the area of coal transportation Its subject is the comparative costing of competing transport erodes. A wide range of costs and aspects of costs are dealt with in terms of engineering - economic analyses of the cost of the components which make up the facility and operating system descriptions of each coal transport mode. The cost comparisons, though analyzed, are not meant to be statements of policy but, rather, an input to decision making. The technical material presented in the succeeding volumes, alone with the earlier work cited above, forms the basis for the analyses. This material may also broaden the general understanding of coal transportation issues and problems. The project is divided into two main sections: (1) lone distance coal transport and (2) gathering and distribution systems. Within each section economic and technological comparisons are made of the available modes. These are used as the basis for comparisons among the modes. Inter-modal compatibility is studied with respect to both mixed trunk line shipment anti with respect to feeder to trunk line and trunk line to distribution systems. The engineering and technological data form the bases for the costing and economic analyses.

Jan 1, 1977

By Paul C. McWilliams

This Bureau of Mines report analyzes data on the physical properties of quartzite rock from the Crescent mine, Coeur d?Alene mining district, Kellogg, Idaho, to demonstrate the use of multivariate techniques. After regression, factor, component, cluster, and discriminant analyses are discussed, these techniques are applied to the Crescent mine data. Three appendixes contain some of the required mathematical and statistical detail plus heuristic examples of three multivariate techniques --component, cluster, and discriminant analysis.

Jan 1, 1978

By D. E. Shanks

The Bureau of Mines surveyed a variety of inorganic ion-exchange materials to determine their suitability for removing valuable accessory elements and troublesome contaminants from metallurgical process and waste streams. Most of the materials, which included molecular sieves, heteropolyacid salts, and hydrous metal oxides, did not give adequate separations, did not have the necessary stability in strong acids or bases, or were not in a physical form suitable for ion-exchange use. Many of the suitable inorganic materials, especially the hydrous oxides, were capable of cation exchange with high capacity only in basic conditions, which caused hydrolysis of most of the cations tested. Multivalent anions, such as arsenate and phosphate, were easily removed from acidic solutions by hydrous oxides. Hydrous zirconia was the best material for this purpose. Multivalent anions were not easily des orbed because of compound formation; therefore, conventional ion-exchange techniques could not be employed. As an alternative approach, hydrous ferric hydroxide was used as a filter material to remove arsenate and phosphate from acid solutions. One gram of arsenic was removed from solution for each 20 g of ferric hydroxide. Ferric hydroxide is preferable to hydrous zirconia for use as a filter material because of low cost.

Jan 1, 1983

By Ralph Husack

The Bureau of Mines investigated the effect of gamma radiation on reactions between Pennsylvania anthracite and fluorine and chlorine. In the tests with fluorine about 90 percent of the coal reacted at 350° C to form volatile products whether or not irradiation was employed. Up to 0.8 ml of liquid products per gram of anthracite was collected. Among the 25 com-pounds indicated by gas chromatography, fluoroform and l,l-difluoroethylene were tentatively identified from their relative retention times and perfluoro-cyclopentane from its infrared spectrum. In addition, a clear, hard, wax, probably a fluorocarbon, was formed at 45° C in both the presence and absence of radiation. With chlorine there was no significant difference due to radiation, and preliminary tests indicated that the chlorine reacted more with the organic matter of anthracite at 200° C than with inorganic matter. At 400° C the results were inconclusive because of excessive corrosion in the reaction vessel.

Jan 1, 1966

By R. J. Kuczynski

The U.S. Bureau of Mines Reno Research Center investigated, developed, and patented a high-temperature cyanide leaching process for recovering platinum-group metals (PGM) from automobile catalysts. A batch pilot plant was constructed at the center and operated to demonstrate this technology to industry. Approximately 1,600 kg of used pellet, monolith, and metal support catalysts containing 1,700 g (54 tr oz) of PGM was processed. Forty-five-kilogram batches of used catalysts were leached with sodium cyanide solution at 160°C for 1 h in a countercurrent processing sequence. This selectively dissolved the PGM. Average extractions from the used pellet catalyst were 96 pet Pt, 95 pct Pd, and 73 pct Rh. Average extractions from the used monolith catalyst were 84 pct Pt, 81 pct Pd, and 66 pet Rh. Heating the pregnant leach solutions to 275°C for 4 h destroyed the PGM-cyanide complexes, causing over 99.7 pct of the PGM to precipitate from solution. The PGM precipitate was predominantly a metallic powder concentrate, typically analyzing greater than 50 pct PGM. Heating destroyed the cyanide to less than 0.2 mg/L free and total cyanide. Both the pellet and monolith residues were evaluated for disposal using the toxicity characteristic leaching procedure developed by the U.S. Environmental Protection Agency.

Jan 1, 2010

By E. Chin

Although Japan is a major producer of crude steel, it is poor in industrial raw materials. This Bureau of fines report describes Japan's raw material needs for chromium, cobalt, manganese, nickel, and tungsten to produce ferroalloys and alloy steels. Japanese imports of these ores or metals by quantity and source are given for 1972-81, inclusive, to indicate (1) the changes in the consumption and supply pattern, and (2) the degree of Japan's dependence on foreign sources. This report also describes measures implemented by Japan to reduce the risk- of supply interruption, and discusses the possible implications of supply shortages.

Jan 1, 1983

By W. W. Adams

Two important facts stand out as features of the metal- and nonmetal-mining4 industry of the United States in 1941 as compared with 1940: First, the number of employees and man-days of employment increased; second, accident-frequency rates, both fatal and nonfatal, decreased. Reports from mining companies to the Bureau of Mines covering underground, open-pit, and surface operations for 1941 re¬vealed the largest number of men employed since 1926 and the largest number of man-days worked since 1929. The combined fatal and non¬fatal accident-frequency rate for 1941, calculated on a basis of one mil¬lion man-hours of exposure to hazard, was (except for 1931 and 1932) the lowest since 1911, the earliest year for which figures are available. During this 31-year period, only 1938 and 1939 showed lower fatality rates, and only 1931 and 1932 had lower nonfatal-injury rates. Operating companies reported that 9,620 mines were active during all or some part of the year. These employed 125,290 men, an increase of more than 4 percent over 1940. The total volume of work performed at all mines, measured in terms of man-shifts, increased to nearly 32 million, a gain of 10 percent; man-hours of employment rose to almost 254 million, an increase of 10 percent over the 231 million man-hours worked in the previous year. The year's operations resulted in an average work-year of 255 days per man, an increase of 13 days per employee over the average working time in 1940. Although the 8-hour day prevails generally at most mines, the industry as a whole averaged 7.94 hours per shift, as in 1940.

Jan 1, 1944

By K. K. Kelley

Sodium-aluminum and potassium-aluminum silicates are among the more important rock-forming minerals of the earth's crust. They also appear as constituents of some metallurgical slags and of some refractory materials. Consequently, knowledge of their thermodynamic properties is interesting and valuable from several viewpoints. This paper reports experimental determinations of the low-temperature heat capacities and entropies at 298.16° K. of albite, jadeite, and nephelite it the sodium-aluminum silicate series and of adularia, ferriferous orthoclase, leucite and kaliophilite in the potassium-aluminum silicate series. Also high-temperature heat-content and entropy increments about 298.16° K. are reported for albite, jadeite, nephelite, and carnegieite in the sodium-aluminum silicate series. Except for a few high-temperature heat-content values for albite, all these data are available for the first time.

Jan 1, 1953