Search Documents

By Glenn A. Shirey

The objective of this contract as to prepare a detailed, readily usable handbook on dust control techniques for longwall mining operations. Information was gathered from available literature, and through contacts with industry and government personnel. The handbook describes those methods of dust control applicable to today's longwall mining systems, and contains sufficient design elements to assist operators with problems in testing or implementing new control procedures. Complete reference lists are presented at the end of each chapter to direct the reader to additional information.

Jan 1, 1985

By C. M. Harrer

This paper describes the location, features, qualities, extent, and potential of iron occurrences and some associative resources -limestone and dolomite, coal, petroleum and natural gas, power, and water - in New Mexico. Reconnaissance investigations were made of 118 iron occurrences to deter-mine their extent, attitude, and potential; character samples were analyzed to determine their quality and impurities; and pioneer metallurgical investigations were made on character samples to present their metallurgical problems. Some factors influencing past and potential iron markets are discussed. The most abundant iron minerals are magnetite and hematite. The higher grade deposits are extensive contact-metamorphic and pyrometasomatic replacements in calcareous Paleozoic rocks associated with intrusives. Low-grade deposits of considerable potential are the extensive Cambrian oolitic hematites of sedimentary origin and the Precambrian magnetite-hematite taconite iron formation. Iron occurs also as extensive colluvial and alluvial concentrations. A wide variety of accessory elements are indicated and these pose metallurgical and economic problems.

Jan 1, 1963

By C. M. Harrer

This paper describes the location, features, qualities, extent, and potential of iron occurrences and some associative resources - limestone and dolomite, coal, petroleum and natural gas, power, and water - in New Mexico. Reconnaissance investigations were made of 118 iron occurrences to determine their extent, attitude, and potential; character samples were analyzed to determine their quality and impurities; and pioneer metallurgical investigations were made on character samples to present their metallurgical problems. Some factors influencing past and potential iron markets are discussed. The most abundant iron minerals are magnetite and hematite, The higher grade deposits are extensive contact-metamorphic and pyrometasomatic replacements in calcareous Paleozoic rocks associated with intrusives. Low-grade deposits of considerable potential are the extensive Cambrian oolitic hematites of sedimentary origin and the Precambrian magnetite-hematite taconite iron formation. Iron occurs also as extensive colluvial and alluvial concentrations. A wide variety of accessory elements are indicated and these pose metallurgical and economic problems.

Jan 1, 1963

By Philip C. Tully

This bibliography contains 2,072 citations to technical and scientific literature about helium and alpha-particles abstracted by 12 abstract service publications during 1962. Citations are listed by 16 major subject classifications with several subclassifications to minimize areas of literature search. Automatic data processing was used to reduce the time and labor required to compile the bibliography.

Jan 1, 1969

By Robert S. Becker

The results of a laboratory investigation of coal cutting mechanics and noise is presented. These experiments were performed using a linear cutting apparatus that operates over a broad cutting speed range. The influence of several coal cutting parameters on the noise, force, productivity, and specific energy associated with linear cuts is ascertained. Some basic theoretical aspects of coal cutting mechanics and noise generation are discussed, and the results of the laboratory experiments are used to Formulate analytical models of the coal cutting forces and noise. The analytical model For coal cutting noise is then generalized to account for the more important effects of rotary cutting. Based on the generalized model, an estimate of the sound pressure level at an operator's position is made for a typical continuous mining machine. It is concluded that by employing linear rather than rotary cuts, using deeper depths of cut, slower cutting speeds, and more efficient cutting tools, it is possible to reduce the level of coal cutting noise, as well as Provide benefits to other important areas of underground health and safety.

Jan 1, 1980

By H. C. Carpenter

This literature study of methods for desulfurizing residual fuel oil was conducted by the Bureau of Mines at the request of the Department of Health, Education, and Welfare. The sulfur compounds in residual fuels are believed to consist chiefly of condensed thiophenes and other polycyclic sulfur compounds. Hydrodesulfurization appears to be the most promising method for desulfurizing these oils and is the only method applicable to all types of sulfur compounds. There are indications in the literature that hydrodesulfurization without hydrocracking of residual oils may require higher pressures than used in present desulfurization processes, but no cost data and little experimental data are available on the higher pressure operation. Literature proposals for hydrogenating residual oils and heavy crude oils are exclusively for hydrocracking the oils to lower boiling products with accompanying partial desulfurization of the residual fuel fraction. Costs of the hydrocracking operations appear the closest available to probable costs of hydrodesulfurizing the oils, and have been reported (in 1955 to 1957) as $500 to $840 investment cost per daily barrel of capacity, with total operating costs of 70 cents to $1.10 per barrel.

Jan 1, 1963

By D. Harrington, W. J. Fene

Explosions are a type of mine accident that can be prevented by known methods ; however , they continue to occur because some mining people are still negligent in adopting and using the known and , in general , readily available measures for avoiding these disasters . Although the frequency and severity of explosions have decreased during the past 5 years there is still much room for improvement . Pennsylvania is an excellent example of what may be done to prevent explosions ; this State had an explosion record by no means good during the decade before 1930 , but by the adoption of readily available and not very expensive safety measures it now has almost entirely eliminated explosions . Pennsylvania bituminous mines now have the enviable record of not having had a major explosion disaster in considerably over 4 years . fact , many of our mining States are showing definite progress in working mines without explosions ; and some of these , like Alabama , West Virginia , Wyoming , and others now operating with few if any explosions , have had anything but a favorable record in the past .

Jan 1, 1934

By R. D. Rosenkranz

The Bureau of Mines has investigated the availability of copper from 272 deposits in market economy countries. The deposits studied have demonstrated resources totaling 413 million metric tons of contained copper and account for more than 90 pct of the reserve base for market economy countries. Using data gathered as part of its Minerals Availability Program, the Bureau performed geologic, engineering, and economic evaluations in order to determine the copper production potential of each deposit. At the 1981 copper market price of $0.85/lb, the deposits studied could economically produce an estimated 88 million metric tons of copper (allowing for profit computed at a 15-pct rate of return), primarily from mines operating at the time of the study (1981). At this price, producing mines in market economy countries could economically produce only 2.1 million metric tons of refined copper per year. However, actual 1981 production was 6.2 million metric tons, indicating that many mines continued to operate even though they were unable to cover all production costs. For U.S. producing mines, the estimated average cost of production per pound (including profit at a 15-pct rate of return) was $0.15 higher than the average cost in other market economy countries.

Jan 1, 1983

By H. F. Yancey

The development, manufacture, and sale of small coal stokers suitable for domestic use has provided a new industry in the United States at a time when badly needed. Sales of domestic stokers have doubled each year for the past 4 years, until in 1936 probably more than 80,000 such units were put into use, According to reports of the Bureau of the Census 75,543 residential stokers mere sold in the first 10 months of 1937 by 108 manufacturers. This rapid expansion has made itself felt in the coal-mining, industry. The smaller sizes of coal, either in a sized or slack condition, are in greater demand; as a result, preparation practices at the mines have had to be revised so that, in many instances, lump coal is being crushed to meet the demand for stoker coal. This situation in turn has necessarily resulted in a realignment of price schedules for the different sizes. One of the first underfeed stokers small enough for domestic use was developed at Seattle, Wash., in 1912 in 1916, a small overfeed stoker was developed at Seattle. These two types are generally considered to represent the beginning of tie present domestic stoker industry in the United States. A careful inquiry as to the number of domestic stokers now installed in the Seattle area, made by C. R. Pate, who was detailed to this duty by the Works Progress Administration, indicated that probably 7,000 domestic stokers are being used in this area for residential heating. Most of these stokers axe of the overfeed type, although in the past 2 years the underfeed type has made rapid gains.

Jan 1, 1938

By Richard W. Knostman

A study was made of the factors affecting lead and zinc production in the Pacific Northwest. Costs, ore reserves and potential resources, and domestic demand were analyzed. It was concluded that a projected 3.1-percent average annual increase in U.S. demand for zinc through 1975 and a corresponding 2.5-percent rise for lead will be supplied mainly from mines in the Eastern and Central States. Annual Pacific Northwest mine production of lead is estimated to fluctuate around 82,000 tons, while zinc output may average 135,000 tons through 1975. Measured, indicated, and inferred reserves in the Pacific Northwest, containing 1.56 million tons of lead and 2.59 million tons of zinc, are more than sufficient to maintain this level of production. Annual production from Pacific Northwest electrolytic zinc plants is expected to increase to over 300,000 tons of slab zinc by 1975. Lead smelters may experience difficulty in maintaining output at 1964 levels.

Jan 1, 1967

By Henry M. Harris

A study was made by the Bureau of Mines to determine if shapes of oxide-glass compositions could be roll-formed at high temperatures, and to find the conditions required for adequate formability. A unit with directly connect' furnaces and heated rolls that allowed forming of most of the compositions developed. Glasses of the feldspar type were chemically unreactive with the alumina grains, and allowed the best roll forming. Optimum forming was attained at temperatures of 1,400° to 1,530° C, with compositions containing 30 or 40 percent feldspar and 60 or 70 percent alumina. Formability was better when compositions contained minus 325-mesh materials, rather than coarser or finer powders. In many cases, roll-formed shapes had physical properties equal to or better than the normally sintered shapes of the same composition.

Jan 1, 1967

By Walter E. Lewis

The Cuyuna iron range in Crow Wing County, Minn., is the principal producer of manganiferous iron ore in the United States. The ore is mined from a manganiferous iron formation in the bedrock of the Cuyuna district. This iron formation is divided into two general lithologic types-thin-bedded and thick-bedded. The unoxidized, thin-bedded iron formation is composed of iron silicate with associated fine-grained carbonates of iron and manganese. The thick-bedded iron formation carries iron and manganese oxides with intimately associated silica. Oxidation and leaching of the original iron formation have been the most influential factors in producing manganiferous iron-ore concentrations in quantities large enough to exploit on a commercial basis. The unoxidized and the partly oxidized and enriched iron-formation materials are suitable as a source of ferrograde manganese ore. These materials have been classified according to their amenability to mineral dressing and degree of oxidation and leaching.

Jan 1, 1958

By Noel N. Moebs

This report summarizes a U.S. Bureau of Mines study on the application of geotechnology to identify and minimize ground control hazards in talc mining operations in northwest Georgia. The major ground control hazard is pillar sloughing attributed to the steeply dipping orientation of a pronounced foliation in the talc ore body. The sloughing problem, which gradually reduces the effective support area of a pillar through attrition, can be minimized by appropriate artificial support, as determined by a rock classification system, and by a more uniform pillar design. A boundary element model confirmed the advantages of using a uniform pillar design to avoid excessive loads on portions of irregular pillars. Instrumentation to measure roof convergence and pillar loading was installed at selected locations in an active talc mine but failed to detect any significant changes, suggesting that the gneiss hanging wall constitutes a strong roof that probably can support large spans between pillars and permit high extraction ratios. This interpretation also is supported by a rock classification of the hanging wall gneiss.

Jan 1, 2010

By F. F. Netzeband

This report relates to the sulfur industry of seven States--Arkansas, Kansas, Louisiana, Mississippi, Missouri, Oklahoma, and Texas--and is part of a national study of the sulfur industry by the Bureau of Mines. Markets as used in this report are divided into two components for individual analysis-- (1) supplier markets which include regional Frasch and byproduct sulfur producers and (2) consumer markets which include processors and manufacturers requiring sulfur in their operations The term sulfur as used in this report includes brimstone, native sulfur, elemental sulfur, or sulfur equivalents.

Jan 1, 1964

By Sarkis G. Ampian

Crystalline silica (quartz, cristobalite, and tridyrnite) is regulated by the Mine Safety and Health Administration (MSHA) and Occupational Safety and Health Administration (OSHA) because of its potential for causing debilitating but nonmalignant lung diseases. In 1987, the International Agency for Research Against Cancer (IARC) conducted a review of the health literature and concluded that crystalline silica was a probable human carcinogen. As a result of this finding, OSHA was required to regulate crystalline silica under its Hazard Communication Standard (HCS). The standard requires that all materials handled by OSHA-regulated facilities be labeled according to the requirements of RCS and that workers receive proper training on the handling of the material if the crystalline silica content equals or exceeds 0.1 weight percent (0.1 %). MSHA currently is considering enacting its own RCS. This will be similar to OSHA's RCS. If the standard is enacted, most mineral producers will have to determine the respirable monitor filter and bulk crystalline silica contents of their ores and products so that workers and/or customers will know whether they are in compliance with the 0.1% HCS and/or the OSHA permissible exposure level (PEL) of 50 µg for an 8-hour workday for respirable crystalline silica as determined from monitor samples. Two major concerns with the RCS are the widespread occurrence of crystalline silica in nature and the suitability of current technology for routinely determining crystalline silica concentrations at the 0.1 % RCS level. Most ores are extracted from silica-bearing deposits and it is a common constituent of rocks and soils. OSHA's RCS will have the greatest impact on the producers of crushed stone, diatomite, dimension stone, gravel, industrial sand, perlite, pumice, pyrophyllite, sand, and talc because these materials frequently are shipped directly from the mill to the customer. MSHA's RCS would affect nearly all mineral producers. Those producers that have crystalline silica present in concentrations near the 0.1 % cutoff point will have the most difficulty with the analysis. Crystalline silica can be quantified at the 0.1 % level by X-ray diffractometry in simple systems containing one, two, and possibly three minerals if (1) none of the accessory minerals has X-ray diffraction reflections that coincide or overlap with those of crystalline silica and (2) the standard has a particle size distribution and crystallinity similar to those of the sample. In some instances, it may not be possible to determine the crystalline silica content of a sample with any degree of certainty using the recommended regulatory protocol. In all cases, it is recommended that a qualified mineralogist identify the minerals in a sample prior to any regulatory analysis. Additionally, the uncertainty as to whether some silica polymorphs should be classified as crystalline or noncrystalline and the suitability of metastable high-temperature standards, such as cristobalite and tridyrnite, for regulatory analysis at ambient temperatures should be addressed further. This overview is written both to highlight these problems and to serve as a guide for analysts, regulators, and industry personnel who are involved in the crystalline silica issue. It also covers some of the difficulties and/or shortcomings in quantifying crystalline silica, such as the ubiquitous mineral quartz, in the workplace.

Jan 1, 1992

By Pamela J. Watson

The U.S. Bureau of Mines has demonstrated in laboratory tests that drilling with surface-charge-neutralizing concentrations of polyethylene oxide (PEO) polymer solutions simultaneously improves penetration rates and extends bit life. The applicability of this additive to improve drilling performance in coal measure rocks was demonstrated under field conditions at an abandoned mine land site in Pennsylvania and a producing coal mine property in Ohio. Penetration rate improvements ranging from 15 to 50 pet were obtained when core drilling through a variety of coal measure lithologies. Drilling cost analysis indicates that the small added cost of using the polymer is more than offset by the savings that result from demonstrated increased drilling penetration rates, which translate into drilling cost savings of about 10 to 30 pct. This report also gives chemical analyses of a variety of coal measure rocks and some corresponding local drilling water samples, obtained from a wide geographical base, along with threshold concentrations of PEO required to effect the improved drilling performance in these rocks. From these data, the threshold PEO concentrations needed to ensure improved drilling performance can be estimated for any coal measure rock suite. Proper techniques for mixing PEO solutions are also presented.

Jan 1, 2010

By Milford L. Skow

This report summarizes the principal activities and results of 15 years of research by the Bureau of Mines, U.S. Department of the Interior, on methane control in coal mines. This research has investigated fundamental factors regarding the occurrence and movement of methane in coal beds, removal of methane prior to mining, and control of methane during mining. The report includes a bibliography listing the more than 150 publications resulting from the Bureau's methane control program as well as numerous other references, a section on methane recovery and use, a look at the upcoming Bureau of Mines research program, and a brief review of methane drainage practices in other coal-producing countries.

Jan 1, 1980

By E. A. Ziemba

The modified in-situ process is one of the methods being considered for extracting oil from oil shale. One of the questions to be answered for this approach is the environmental consequence of underground retort abandonment. This report outlines a study which addresses the question in terms of a grouting solution. It covers the development of a spent shale ash based grout which will fulfill the environmental requirements in terms of strength, stability, and impermeability. In addition, it will allow the reinjection of up to 50 percent of material mined and surface retorted as part of this process.

Jan 1, 1982

By Paul Biggs

This Bureau of Mines report contains information on 63 water flood projects in Colorado. Water was injected in 10 formations located in 58 oilfields. Specific field data presented include location, discovery, development, water supply, fluid injection, oil and water production, oil reserves, and oil recoveries by primary and secondary methods. An estimated 3.5 billion barrels of water has been injected to recover approximately 533 million barrels of oil, a ratio of 6.57 to 1. Most of the injection water is from alluvial deposits, although produced water is used in many fields. Injection water treatment is not a major problem. Appraisal of project success or failure in this report is based on technical, rather than economic, information.

Jan 1, 1974

By D. R. Tweeton

The U.S. Bureau of Mines, the University of Arizona, Sandia National Laboratories, and Zonge Engineering and Research Organization, Inc., conducted cooperative field tests of six electromagnetic (EM) geophysical methods to compare their effectiveness in locating a brine solution simulating in situ leach solution or a high-conductivity plume of contamination. The brine was approximately 160 m below the surface. The testsite was the University's San Xavier experimental mine near Tucson, AZ. Geo- physical surveys using surface and surface-borehole, time-domain electromagnetic (TEM) induction; surface controlled-source audiofrequency magnetotellurics (CSAMT); surface-borehole, frequency- domain electromagnetic (FEM) induction; crosshole FEM; and surface magnetic field ellipticity were conducted before and during brine injection. The surface TEM data showed a broad decrease in resistivity. CSAMT measurements with the conventional orientation did not detect the brine, but measurements with another orientation indicated some decrease in resistivity. The surface-borehole and crosshole methods located a known fracture and other fracture zones inferred from borehole induction logs. Surface magnetic field ellipticity data showed a broad decrease in resistivity at depth following brine injection.

Jan 1, 2010