Search Documents

By J. M. Singer

This study was undertaken to obtain some fundamental information about hazardous mixtures of coal dust and methane (firedamp) likely to occur in mines. Fuel concentration limits for ignition of mixtures of coal dust, methane, and air have been determined by a hot-gas ignition method. The limiting concentration of each of the two fuels was usually less than that corresponding to its lean flammability limit in air. The lean limits of flammability of coal dust vary with the type and size of the dust; in this study coal dust concentrations were less than 80 mg/liter. Ignition jets were turbulent pulses (emerging from a channel of 0.5 cm diam) resulting from explosions of stoichiometric mixtures of methane, oxygen, and nitrogen, Temperatures of the ignition jets were varied by changing the oxygen index (OI) = O2/(02 + Nj2) of the primary methane-oxygen-nitrogen mixture (adiabatic flame temperatures from 2,000° to 3,000° K). The objectives of the study were to establish quantitative relations between concentrations of each fuel at ignition limits of hybrid mixtures and to study the mechanism of ignition of these hybrid mixtures by hot turbulent gases, Empirical equations were fitted to concentrations for four coals, namely) Pittsburgh Seam (sizes A, B, and C), Sewell No.2 Seam, pocahontas No.3 Seam, and anthracite. Equivalences of coal dust to methane were computed from these equations; equivalence being defined as -Ac/Am, where c is the coal dust concentration and m is the methane concentration, each in milligrams per liter of air. It was found that the equivalence increases as the temperature of the hot-gas jet decreases. In general, the equivalence is also an inverse function of volatile content of the coal and a direct function of the particle size, However, volatile con-tent in itself is not a sufficient correlating variable, nor is the specific surface area of the coal dust.

Jan 1, 1967

By John R. McWilliams

The technological and economic pattern of the U. S. mining industry has undergone a rapid and continuing change since World War II. To provide realistic up-to-date cost data and to disseminate knowledge of technical developments, the Federal Bureau of Mines, with the cooperation of individual mining companies, is presenting a series of mining methods and costs reports similar to those it issued before 1939. Shaft sinking has always played an important part in mine development and [ration] and is an appropriate subject for this series of reports. Shafts [are] especially important in areas such as the Coeur d'Alene district of Idaho, where every major mine is served by one or more shafts and shaft sinking is in progress at one mine or and her almost continuously.

Jan 1, 1960

To address the safety of programmable electronics-based mining systems before this technology proliferates in the mining industry.

Jan 1, 1999

By Alla D. Mah

THERMODYNAMIC data for manganese and its inorganic compounds have not been critically surveyed since the work of Maier (31) 3 in 1934. At that time data were lacking or inadequate for many of the important metallurgical compounds. Experimental work, conducted during the intervening years, has supplied so many new thermodynamic values that it is again desirable to examine the available data and compile them into a single publication for handy reference. This paper consists of three main sections. The first summarizes the basic metallurgical thermodynamic data for manganese and its compounds, including heat capacities, entropies, heat contents, temperatures and heats of phase changes, vapor pressures, and heats and free energies of formation. All data available to May 1959 have been considered. The second section contains heats, free energies, equilibrium pressures, and equilibrium constants of reactions of manganese compounds, with special emphasis on metallurgical reactions. The third section supplies basic thermodynamic data for other elements and compounds encountered in metallurgical reactions of manganese, thus making it possible for the reader to conduct thermodynamic calculations without recourse to other literature.

Jan 1, 1960

By John C. Machisak

The thirty-fifth consecutive National Safety Competition sponsored and conducted annually by the Federal Bureau of Mines, Department of the Interior, closed with several noteworthy accomplishments to its credit. Some of them are: 1. A record low injury-frequency rate of 18.293 disabling work injuries per million man-hours equal to that established in 1957. 2. The third lowest injury-severity rate (4,335). 3. The second highest number of mines and quarries participating (672) 4. A record number of participants finishing the competitive year without a disabling work injury. 5. All recipients of Sentinels of Safety trophies free of disabling work injuries for the first time since 1952.

Jan 1, 1961

By O. C. Blade

This report on the properties of motor fuels sold through service stations in the United States was made in accordance with a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. By agreement with the American Petroleum Institute, identification of the items is confidential. It presents analytical data for 4,954 samples, representing the products of 93 companies. The samples were collected during December 1955, January and February 1956. As in previous surveys, the gasolines covered by this survey include those from both large and small suppliers. The data were obtained by laboratories of various refiners, motor manufacturers, and chemical companies and submitted to the Bureau of Mines for compilation. A list of the National Motor Gasoline Survey reports published during the post 10 years is given on page 5.

Jan 1, 1956

By Jerry Olson

The Bureau of Mines (Bureau) conducted a mineral resource investigation of the French Creek-Patrick Butte study area, in west central Idaho during 1989. No mineral resources or significant occurrences were identified. Other than small scale placer gold, no mineral production is known or recorded. At least 100 lode and 150 placer claims have been located in the study area. Most of the area was examined by ground or areal surveys, and 110 lode and 60 placer samples were taken. Four lode prospects were examined in detail, and all placer claim locations were sampled.

Jan 1, 1991

By William W. Adams

A general increase in employment prevailed in the stone-quarrying industry of the United States during 1941 compared with 1940. Likewise, more accidents occurred to men working in and about the quarries, with the result that the accident-frequency rate for the industry as a whole was higher in 1941 than in the previous year. Reports from operating companies to the Bureau of Mines, covering open and underground quarries, as well as rock-crushing and rock-dressing plants, cement mills, and limekilns at or near the quarries, showed a total of 86,123 men employed and a total of more than 22 million man-days of labor performed during 1941. The total working time of the industry averaged 260 days per man. Measured in man-hours, the volume of work equaled 173 million, an average of 2,011 man-hours per employee.

Jan 1, 1943

By B. R. Mohal, S. Chander

"The adsorption and wetting behavior of freshly ground and aged coals has been determined in the presence of a nonionic surfactant. The amount of surfactant adsorption changes with the concentration and ""age"" of the coal. The freshly ground coal has smaller amounts of adsorption at lower surfactant concentrations than the ""aged"" coal whereas at large surfactant concentrations, the order is reversed . In the latter case, more surfactant is adsorbed on fresh coal than on the ""aged"" coal . . It is proposed that at low concentrations, the surfactant adsorbs through both hydrophobic and hydrophilic interactions with the molecule lying parallel to the· surface, whereas at higher concentrations surface micelles form at the hydrophobic sites. The wetting behavior correlates well with the adsorption behavior.INTRODUCTIONNonionic surfactants have many applications in the coal and mineral processing industry. They can be used as dispersing agents to modulate flotation, flocculation and filtration of particulates (1). They can also be used to increase the wettability of hydrophobic solids such as coal and can hence be used as dust suppressants (2,3). Although the adsorption of representative nonionic surfactants such as Triton N-101 (an ethoxylated nonylphenol with 9.5 moles of ~thylene oxide and HLB equal to 13.4) have been studied extensively on substrates such as calcium carbonate (4), silica (5) carbon black (6) and graphite (7), very few studies are available for coals. Coals differ from other substrates with respect to two important characteristics: 1) coal are porous and 2) coals consist of a patchwork of hydrophobic and hydrophilic sites (8). Since the adsorption characteristics of a surfactant are influenced significantly by the nature of the substrate the characteristics of the coals must be taken into consideration."

Jan 1, 1989

By James L. Elder

The Bureau of Mines and the Alabama. Power Co. jointly conducted a first experiment in underground gasification of coal at Gorgas, Ala., during the fall and winter of 1946-47. This preliminary experiment showed that it was not difficult to maintain combustion of coal underground, and that coal in place could be completely gasified. It was noted that the high temperature developed by the gasification of coal in place brought about changes in overlying strata that appeared to be favorable to the process. The high temperatures caused the roof rock to become plastic, to expand, and to settle down on the mine floor directly behind the reacting coke face. These results were promising enough to warrant further investigation of the process. It was believed that if this action could be controlled properly with roofs of similar composition, it would tend to force the gas-making fluids underground against the coal faces. Plans for the second experiment were based in part on this favor-able roof action, and the successful operation of the planned initial straightline passages depended on this fact. Gorgas was chosen as the site for the second experiment for the following reasons: A tract of coal land of sufficient size was available and isolated from the main body of coal; the roof rock was similar in composition to that encountered in the first experiment; and the overlying strata were thick enough to eliminate some of the operating difficulties that had been encountered, In addition, power, water, and machine-shop facilities as well as an adequate supply of labor were available in this area, and the friendly cooperation of the Alabama Power Co. further recommended this site for the planned experiment.

Jan 1, 1951

By G. W. Murrie

A geologic study of the Mary Lee Group of coalbeds in the Black Warrior coal basin was undertaken to examine coal stratigraphy and determine regional trends and extent of the coalbeds. The area investigated encompasses 835 square miles in Jefferson, Walker, and Tuscaloosa Counties, Ala. More than 700 core logs were used to construct a structure map, coal, interval, and overburden isopachs, and cross sections. There is evidence that structure affected sedimentation. Coalbed isopachs indicate the Mary Lee Group was deposited in fluvial-deltaic and low-lying coastal plain environments. The Mary Lee coalbed is the only coalbed which is continuous throughout the area, commonly with two benches which have a combined thickness of 2 to 12 feet. The Mary Lee coalbed changes rank in the basin from high-through medium-to low-volatile coal. The methane gas potential of the Mary Lee Group coals is estimated to be greater than 1 trillion cubic feet. There is an excellent correlation between the orientation of surface cleats with those measured underground in the Mary Lee coalbed. The face cleats roughly parallel the axes of the area's folds and trend northeast-southwest.

Jan 1, 1976

By Robert E. Wood

The compressibility factors, Z, of helium, nitrogen, and helium-nitrogen mixtures in the three-dimensional space of temperature, pressure, and gas composition have been related to the Leiden form of the virial equation of state. The dependency of virial coefficients through the fifth on temperature and gas composition has been established for the temperature range 133.15° to 748.15° K. Compressibility factors, Z, have been computed from the equation of state and tabulated as functions of gas composition, pressure, and temperature. Tabular values of Z are presented for 30.00 through 100.00 percent helium for temperatures from 240° through 700° R for pressures from 14.696 through 3,050 psia and for temperatures from 720° through 1,300° R for pressures from 14.696 through 1,500 psia. Tabular values of Z are presented at increments of 5.00 percent helium and 20° R, and, for pressures greater than 50 psia, at increments of 50 psi.

Jan 1, 1967

By Lewis A. Smith

This circular presents a summary of the domestic chromium industry, and discusses the salient features of the world situation , reflecting the literature of the subject . The United States Bureau of Mines has in its files additional detailed information on many subjects briefly discussed in this paper and desires to assist the industries and the public by giving further data in response to individual inquiries . It will welcome comment and criticism and any contributions that would assist in making future editions of this circular more accurate . Unlike most common metals , chromium is rarely marketed as a pure metal . The chromium industry deals mainly with chromite , the principal ore of chromium , and with ferrochromium , the basic alloy in which chromium enters the metallurgical industry.

Apr 1, 1932

By C. Babcock

When a flat-lying mineral deposit such as a coal seam is mined, some coal is left to separate the roof and floor so that miners and machines can safely mine the seam. The mineral left is in the form of mine pillars. If too much is taken, support problems and unsafe working conditions result. If too little is taken, the mining operation will be unable to compete economically with other mines. Therefore, one must select pillars of the optimal size to maximize mining recovery and minimize risk to miners and equipment. Later, if the pillar support is no longer needed and the surface can be allowed to subside the thickness of the coal seam, then the pillar support can be removed to increase mining recovery, and initial pillar size is not as critical. Only a small part of the information available on pillar design can be presented here. The purpose of this report is to summarize some of the work done by the U.S. Bureau of Mines and others on pillar design, which is reported in the literature from 1833 to the present, and present rock mechanics test results that aid in understanding mine pillar behavior. The variable names used are those of the authors cited. This results in multiple use of some variable names.

Jan 1, 1994

By G. B. Shea

Among the many engineering problems directly related to conservation in the petroleum industry, that of crude-oil emulsions continues to be important. Emulsions of water and oil always have constituted one of the most serious forms of waste in the oil fields, and the necessity of dehydrating emulsified crude petroleum to obtain marketable or pipe-line oil confronts operators in many fields with a major operating problem. In 1926 the Bureau of Mines published a comprehensive treatise s on oil-field emulsions dealing with field conditions, practical methods of dehydration, and physicochemical characteristics of the formation and resolution of emulsions. Although this bulletin is still available and may be obtained from the Superintendent of Documents, Washington, D. C., and although its contents are a valuable reference on the subject of emulsions, knowledge regarding the physical properties of emulsions and the phenomena of dehydration has increased greatly within the last decade. With the information gained through continued scientific research, substantial improvements have been made in the art of resolving petroleum emulsions. Moreover, in recent years there has been a growing realization of the importance of emulsion-preventive measures that has led to more critical examination of the causes of emulsions and methods of eliminating or at least reducing the degree of emulsification. Conditions causing agitation and commingling of oil and water and the formation of "cut oil" often are within the control of the producer, thereby making it possible to utilize preventive or remedial measures by which emulsification may be minimized or avoided. In fact, many companies have materially reduced their treating costs as a result of careful studies in emulsion prevention and proper handling of "wet" production. Of course, in many instances preventive measures or the correction of conditions causing emulsification cannot be achieved practically or economically, and the emulsions that form must be treated regardless of the care exercised or the money spent in attempting to prevent their formation.

Jan 1, 1939

By Richard N. Spencer

Electric-furnace smelting for simultaneous recovery of zinc spelter and lead bullion from complex lead-zinc sinter was investigated. Reduction of lead and zinc was satisfactory. Condensation of lead and zinc vapor to pyrophoric metal powder in a water-cooled, shock-condensing system produced excellent recoveries. Metal-splash condensation to produce zinc spelter was unsatisfactory. Special smelting experiments differentiated the effects of several smelting parameters on zinc metal recovery. The principal cause for unsatisfactory zinc metal recovery was transfer of iron to the condenser and subsequent degradation of zinc in a mixture composed of lead and an iron-zinc intermetallic compound. Limitations of the process were determined. Slag-resistance open-bath electric smelting of complex lead-zinc sinter is not considered feasible.

Jan 1, 1967

By H. A. Schrecengost, H. R. Gil, Alfred Clarkson, E. H. McCleary

Much has been written and many discussions have been held concerning the prevention of accidents in coal mines , and considerable progress has been made in eliminating hazards to the health and safety of underground workmen . Although much progress has been made in the reduction of injury rates in the Pennsylvania anthracite field , the injury rates for the anthracite mines of Pennsylvania are generally higher than the average for coal mines in the United States as a whole , because the mining conditions , including the safety problems , in the Pennsylvania anthracite fields are more complex than in other coal fields of the United States . Several factors contribute to this extremely difficult problem , among which are : Multiple - vein mining , steeply pitching measures , folds or faults , hard smooth floors underneath the veins , and the remining or reclaiming of pillars in severely crushed , broken ground . In the early days of the Pennsylvania anthracite industry , only the more productive veins were mined , and this resulted in bypassing those veins that were relatively thin and those containing considerable proportions of impurities . However , the development of modern coal - preparation equipment , improved marketing conditions , and the adoption of mechanical equipment , such as the various types of conveyors and scraper loaders , have made possible the recovery of the thinner and poorer veins . Furthermore , in the early days , little or no attempt was made to recover the coal pillars , usually owing to the great amount of virgin coal available . Consequently , much of the anthracite produced within the last few years has been recovered by second and third mining and frequently by fourth mining - in areas where operations had been suspended for many years . In such areas , the coal veins and intervening strata are usually crushed as the result of gradual subsidence , which intensifies the hazards incidental to roof control , haulage , ventilation , and mine gases . Moreover , the use of coal - cutting equipment is not practicable in most anthracite mines because of. the inclination of the veins and because , in crushed -ground areas , the faces must be advanced slowly and for short distances at a time to permit the erection of timber sets and the placing of forepoles to support the roof and sides . Thus , the slow process of mining brought about by these conditions has resulted in the production of only 0.424 ton of anthracite for each man- hour worked , as compared with 0.753 ton? for each man - hour worked at other coal mines in the United States . A summary contained in Bulletin 462,8/ a publication of the Federal Bureau of Mines , reveals that the rate of fatal injuries in the Pennsylvania anthracite industry was improved from 13.47 deaths per million tons produced in 1870 to 3.88 deaths per million tons mined in 1942. During the period March 16 , 1942 to January 1 , 1947 , the fatality rate was reduced from 3.88 to 2.87 deaths for each million tons mined . On the million man-hour basis , the rate of fatal injuries was reduced from 1.643 to 1.130 and the nonfatalinjury rate was lowered from 119.01 to 83.12 during the same period . The improvements made in both the fatal- and nonfatal - injury rates have required the cooperation of the workmen , the mining companies , and the State and Federal inspection departments . Many individual mines and companies have achieved commendable safety records which contributed greatly to the over - all average for the industry , particularly during the 1942-47 period . One of the most outstanding of these is the Continental mine of the Continental -Archbald Coal Co. , a member of the Moffat Co. Interests .

Jun 1, 1948

By Michael S. Miller

The U.S. Bureau of Mines (USBM) conducted mineral investigations in the 1,227,000-acre Emigrant Trail study area of Nevada during 1992. During the USBM investigation of 25 areas of development interest, 190 mineral localities were identified and 260 rock and 50 alluvial samples were taken. At least 0.5 million troy ounces of gold, 2.3 million troy ounces of silver, 3.3 million pounds of copper, 10.9 million pounds of lead, 2.4 million pounds of zinc, 500 tons of alunite, 40,000 tons of sulfur, 9,000 pounds of mercury, and 21,000 pounds of tin have been mined from the area and vicinity. Adjacent to the study area, gold is being mined at large, open-pit gold mines, the Hog Ranch and Hycroft Resources, Inc., Sulphur mines, and new production is planned at the Rosebud LAC/Equinox. Hog Ranch mine is nearing depletion, but resources of more than 0.5 million troy ounces of gold and about 5 million ounces of silver are estimated for the Rosebud LAC/Equinox project and more than 0.4 million ounces of gold for the Hycroft Resources, Inc., Sulphur mine. Significant investigations are occurring at SP Ridge and other sites near Scossa and at the Dan claims in the Southern Calico Mountains. Precious opal, placer gold, and geothermal energy resources occur in the study area and vicinity.

Jan 1, 1993

By R. A. Cattell

Progress of Bureau of Mines research related to oil and gas during the past fiscal year has been marked by the publication of more than 40 reports on the various phases of the work . These include papers dealing with the production of oil and gas , transportation of gas , chemistry and refining of petroleum , thermodynamic properties of hydrocarbons , and the processing and utiliza- tion of helium . As an additional service to Pennsylvania oil operators , a new suboffice was opened in Bradford , Pa . , during the year . With this addition , the work of the Petroleum and Natural Gas Branch of the Bureau of Mines is now conducted in two large stations , the Petroleum Experiment Station , Bartlesville , Okla . , and the Petroleum and Oil Shale Experiment Station , Laramie , Wyo . , and three field offices and laboratories at San Francisco , Calif . , Dallas , Tex . , and Franklin, Pa., and two suboffices, Wichita Falls, Tex., and the newly opened suboffice at Bradford, Pa. In addition, this Branch operates large-scale helium-production plants in Texas, Kansas, and New Mexico, and maintains ex- tensive helium-bearing gas reserves in Texas and New Mexico. All helium opera- tions are supervised from headquarters at Amarillo, Tex. A small headquarters staff is in Washington, D. C. A backward glance at the road traveled during the past several years by the Petroleum and Natural Gas Eranch of the Bureau of Mines brings out a general background for the events of the fiscal year 1949. Throughout the fiscal year 1945, the activities of the Branch were still mainly concerned with such war activities as making special field studies for the Petroleum Adminis- tration for War, finding ways of increasing rates of production, and supplying data pertaining to the manufacture of aviation and jet-propulsion fuels. A period of adjustment came in 1946, characterized by a turning from war to peace procedures and efforts to give wide distribution to technical facts ob tained in wartime research; also, there came a realization that the demands of war had broadened the horizons of research. This was emphasized in 1947, when a peacetime program was restored, based upon the long view of the Bureau's place as a research agency in oil and gas. Close attention was given to tech- nical detail in 1948, and emphasis was placed on maintaining a balance between the industrial need for technical knowledge and Governmental-research possi- bilities in the fields of (1) withdrawal of petroleum from natural deposits, (2) utilization of petroleum and its products, and (3) commercial utilization of helium. Studies of petroleum production and utilization and helium production and utilization are the normal functions of the Branch. These functions (sometimes expressed in different words) have been the mainstay of this organization since initiation of the work. The details of approach vary with changing conditions, but, fundamentally, the functions have been the same in both peace and war. The work of the past fiscal year has emphasized the advantages that accrue when Government and industry join in a wise use of technical and scientific knowledge gained through research. Outstanding evidence of the beneficial results of cooperative effort by the Bureau of Mines and various organizations is found in the following typical examples, the details of which are discussed in the body of this report. Working in close cooperation with operators along the Gulf Coast, the Natural Gasoline Association of America, and the National Association of Cor- rosion Engineers, the Bureau found, through field testing, that corrosion protection by means of chromates in high-pressure gas-condensate wells costs less than $1 per million cubic feet of gas produced. Laboratory experiments to measure the corrosion effects of carbonic and propionic acids on various steels and alloy steels gave data that will serve as guides in the selection of new. materials for the construction of well equipment to be tested by industry under actual service conditions.

Feb 1, 1950

By Russell J. Foster

Public awareness of, and involvement in, recycling has increased significantly in recent years. Nevertheless, recycling is generally perceived as a new development, and is familiar only in the context of municipal solid waste management. The actual magnitude and scope of metals recycling in the United States have gone virtually unnoticed. Over time, both the quantitative and qualitative aspects of secondary metals recovery and reuse have changed substantially, while the attendant regulations have become increasingly stringent. This U.S. Bureau of Mines report examines trends and developments in major metal demand and recycling, and analyzes the possible impacts of regulations with regard to recycling activities.

Jan 1, 1994