Search Documents

By J. J. Forbes

The investigation of major and minor coal-mine disasters has been a routine function of the Bureau of Mines since its inception in 1910, and the facts obtained during such investigations have been used as a basis for determining the precautions that the managements and employees of many mines are observing to forestall similar occurrences. The Bureau has conducted research on roof-control and other mine problems, but a comprehensive study of other fatal accidents was not attempted until February 10, 1950, when the policy of investigating all coal-mine fatalities in the United States was approved by Bureau of Mines Director James Boyd. The investigations are being conducted by Federal coal mine inspectors functioning under the provisions of the Coal Mine Inspection and Investigation Act of May, 1941, Public Law 49; and reports covering the investigations are distributed to management, the State mine-inspection agency, and representatives of the mine workers' organization have jurisdiction at the mine.

Jan 1, 1951

By John W. Buch

Safety and cost in mining coal beds under the extreme pressures found at depth, full extraction to conserve resources, and even surface subsidence to minimize damage of improved areas have directed much well-deserved attention, in the United Kingdom; to roof-control methods. Because the effects of pressure will be felt intensely as our Pennsylvania anthracite mines grow deeper, the senior author took advantage of an opportunity afforded by a mission to Europe3/ to observe, to a limited extent, the effects of pressures found in deep mines and the manner in which they are con trolled. Organized research relating to strata control has been carried on in Great Britain for nearly 25 years. These activities have been ably outlined by Dr. D. W. Phillips.4/ Physical properties of coal-measure rocks, movements of roof and floor, and types of face and roadway supports have been investigated. Same of the forces induced by the extraction of coal have been measured. The results of this research have been publicized and openly discussed, and much progress has been made in establishing a better factual understanding of roof-control problems and their solution.

Jan 1, 1951

By L. A. Morley

Volume IV of the final report examines the problem of indirect contact of overhead high-voltage power lines by mining personnel. This refers to the contact of energized lines by workers through some intermediate conductor such as a metallic tool or a piece of high-reaching mobile equipment, thus the term "indirect contact." The shock hazard presented by such contact has been a major cause of electrical fatalities associated with mining operations. The report volume is divided into three major areas. The first gives a general background of overhead lines, basic characteristics, and associated hazards, and continues to describe presently used techniques and devices which attempt to alleviate the contact problem. The second area narrows the discussion to the mining industry by presenting a detailed analysis of 39 overhead-line contact accidents in mining since 1970. The third major section uses the information from the first two areas to formulate recommendations to prevent these accidents and subsequent electrocutions at mining operations.

Jan 1, 1982

By Joseph Grumer

The range of composition of gases synthesized from solid fuels which are exchangeable with natural gas on current gas appliances was evaluated by theoretical principles. These principles consider primarily the flashback, blowoff, and yellow-tipping characteristics of air-entraining burner flames. It was found that complete identity between the synthetic and natural product is not necessary. Gases such as may be obtained by hydrogasification of coal and other solid fuels without the removal of unreacted hydrogen offer advantages in flame characteristics. Between 25 to 37 percent hydrogen can be tolerated in the sendout gas.

Jan 1, 1965

By L. B. Pankratz

Thermodynamic data on the halides were reviewed, evaluated, and compiled at the Bureau of Mines Albany Research Center. Values for Cp°, S°, H-H°298, -(G°-H°298)/T, ?Hf°, ?Gf°, and log Kf are given in tabular form. CP°, H-H°298, ?Hf°, and AGf° are also expressed algebraically.

Jan 1, 1984

By William Seymour

"INTRODUCTION Byproduct-coke manufacture is one of our country's most essential in¬dustries; its importance was strikingly accentuated by the demands of World War II. This paper reviews recent progress in various phases of byproduct-coke operations for the production of metallurgical coke particularly that used as blast-furnace fuel.In the early days of the by-product-coke industry in the United States high-grade bituminous coking coals, both high-volatile or gas coal and low-volatile Pocahontas coal, were plentiful, and the selection and mixing of coals for coke-oven use were minor problems.The demands of World War I for the production of iron, steel, and coke aroused and stimulated new interest in the investigation of the reserves, characteristics, and properties of our coking coals. During that war the increased demand for coke reached a critical stage, and the shortage of high-grade coking coals necessitated the use of cols of inferior quality and of different coking characteristics than those previously used.The period of prosperity following World War I brought much progress and development in the by-product-coke industry. Methods of testing coal and coke were improved. The search for satisfactory coking coals was continued, and construction and design of byproduct ovens were improved."

Jun 1, 1946

By R. W. Geehan

The Bureau of Mines has been investigating deposits of critical and essential minerals in the United States since 1939. Bureau engineers made a preliminary examination of the Morefield mine early in 1943 and recommended investigation by trenching and diamond drilling, The Bureau of Mines conducted work from August to December of 1943, which indicated that the Morefield mine was a favorable location for an experimental mining program. The Bureau of Mines carried on such a program from September 1947 to March 1949. The property investigated is 30 miles southwest of Richmond in Amelia County, Va. (fig. 1). During World War II mica and beryl were shipped from the Morefield mine, but after the high prices and premiums paid during the war years were not available the mine was closed.

Jan 1, 1953

By T. T. Tomimatsu

This? Bureau of Mines paper discusses the corporate structure dynamics, methods of financing, and financial assessment approaches that should be utilized to evaluate the economic health of the coal industry. It suggests rates of return and other measures of corporate economies necessary to attract capital required to finance emerging coal demand, plus impact of coal sales to total revenues. The study illuminates the activities of 30 selected coal-producing companies, including their subsidiaries or affiliates, that were responsible for approximately 60 percent of the total U.S. production in 1974. The selected firms are not all primary coal producers; many of the larger producer's are classified by the financial institutions as petroleum, metal, and steel producers, public utilities, or chemical industries. The bituminous coal industry is highly competitive as to price, service, and quality of pronuct and is subject to competition from other noncoal energy sources. The top 15 bituminous coal-producing companies mined about 46.6 per-cent of the Nation's total production in 1974, and the balance of approximately 3,885 companies were responsible for the rest of the production. Thus, the U.S. bituminous coal industry is not an oligopoly. Today, about 65 percent of the Nation's total coal production is consumed by electric power utilities and 26 percent by steel, space heating, and other industries; the balance of 9 percent is exported.

Jan 1, 1976

By E. C. Foster

The project objective of this contract is to design, develop, and demonstrate a dust collecting system for auger head miners, used in coal seams 40 inches or less in height, which will reduce respirable dust below the limits established by the Federal Coal Mine Health and Safety Act of 1969. This system was to be incorporated into 3 Wilcox Mark 20 continuous miner. In order to accomplish this, the objective was divided in three main areas. First: To develop a dust control system which would remove by isolation, respirable dust from the face area and areas where miners work. Second: To develop a dust scrubbing system to remove and collect float dust before the air reaches the return airway. Third: To reduce the overall noise levels to which the miners are exposed.

Jan 1, 1974

By C. A. Taylor, C. E. Munroe

"In blasting the explosion of the high explosives charge is initiated by means of a detonator. Consequently the successful operation of the whole system is, ab initio dependent upon the suitability and efficiency of the detonator used. A considerable number of methods for testing the efficiency of detonators have been devised. In a previous publication*** of the Bureau of Mines many of these were discussed after having been classified as direct and indirect methods.In 1910, W. O, Snelling, then explosives chemist of the Bureau, devised a direct method which depends on the extent to which a hard brittle material of uniform granulation, such as quartz sand, is pulverized by the explosion of the detonator when imbedded in it, and, as a container in which to carry out the tests, he devised the vessel known as the Bureau of Mines sand-test bomb No. 1. A brief mention of his work was made in a paper presented to the Engineers' Society of Western Pennsylvania.****Later Storm and Cope made a very extended investigation of this method using sand-test bomb No, 1. Their paper***** contains a detailed, illustrated, description of sand-test bomb No. 1, with precise specifications of the sand and a minute account of the technique followed, together with a discussion of the data they obtained from the tests in this bomb of 112 detonators representing each of the grades from We, 3 to No. 10, inclusive. The average of results obtained by them are set forth in the following table."

Dec 1, 1923

By Charles V. Jude

This U.S. Bureau of Mines report presents a review and evaluation of existing and new backfilling materials and methods for their applicability to the problem of gate road stress reduction in deep retreat longwall coal mines. Candidate backfill materials include pulverized coal combustion fly ash, flue gas desulfurization, and fluidized bed combustion by-products from coal-fired electric power generation plants. Properties of both backfill and its component materials are presented, with particular emphasis on the unconfined compressive strength and elastic modulus of backfill mixtures. Hydraulic mix designs discussed in this report include high-water content slurry and low-water content paste fills. Three gate road stress-transfer-modification concepts are proposed to reduce abutment stresses in gate road systems. The first concept, packwalling, involves packwall construction behind the headgate shield inby the face and adjacent to the headgate pillars. The second concept, gob-filling, involves infilling a strip of gob inset from and parallel to the headgate using paste injection methods patterned after a technology recently developed in Europe. In the third concept, entry-filling, slurry fill methods are used to fill abandoned gate roads and crosscut entries inby the face.

Jan 1, 1995

By Lewis C. Karrick, Martin J. Gavin

"Introduction.The theory of fractional ""education"" of oil from oil shale has been used by several inventors as the basis for the design of retorts for the production of oil from the oil shales of the United States. The term fractional ""education"" gives expression to the rather common belief that when an oil shales is heated it produces light, low-boiling oils as low temperatures, and increasingly heavier, higher-boiling oils as the temperature of retort¬ing rises. The theory evidently had its origin in the fact that crude petroleum may be fractionally distilled, yielding light oils at low distillation temperatures, and heavier oils as the distillation temperature increases is as, gasoline is produced from petroleum at relatively low temperatures, kerosene at higher temperature, and heavier products such as gas-oil and lubricating distillation at still higher temperatures.The writers have examined several oil-shale retorts designed to take advantage of the belief that crude, and in some cases refined, gasoline can be recovered from the shale at low temperatures; kerosene at higher temperat.res, and so on. Such retorts are usually designed to operate continuously and have several vapor-pipes lending from them at differing intervals and passing to separate condensers. Designers of such retorts repeat that the distillate from the low-temperature parts of the retort will be gasoline, and that as the shale passes to zones of increasingly higher temperatures, the vapor lines lending from these zones rill remove increasingly heavier products such as kerosene, gas-oil etc."

Mar 1, 1924

Toward the goal of maximizing minerals and metals recovery from domestic resources, the Bureau of Mines, U.S. Department of the Interior, has conducted in situ corrosion studies at the Salton Sea Known Geothermal Resources Area (KGRA) in the Imperial Valley, Calif., to evaluate and characterize materials of construction for geothermal resources recovery plants. General-, pitting, and crevice-corrosion characteristics of 13 commercially available alloys were investigated for periods of 15 and 30 days in seven process environments expected to be found in typical geothermal resources plants. Stainless steel alloy 29.4, Inconel 625, and the Hastelloys G, S, and C-276 were the most resistant to general corrosion, did not pit, and exhibited little susceptibility to crevice corrosion. Stainless steel alloys 430, E-Brite 26-1, and 6X had low general corrosion rates, but pitted and were susceptible to crevice corrosion. Stainless steel alloy 316 L had a low corrosion rate, but corroded intergranularly, pitted, and was susceptible to crevice corrosion and to stress-corrosion cracking. Titanium-1.5 nickel and TiCode-12 had low corrosion rates, did not pit, and were not susceptible to crevice corrosion. Carbon and 4130 steels had high corrosion rates, pitted, and had high susceptibilities to crevice corrosion. The major scale-forming mineral on the corrosion samples in most of the process environments studied was galena mixed with lesser amounts of other minerals.

Jan 1, 1979

By Barton K. Cross

The objectives of this effort were to: 1) Develop and validate start-of-shift operational inspection procedures to be used by operators of mobile, self-propelled equipment used in surface mining operations; 2) Evaluate user acceptance of the developed procedures; and 3) Recommend methods and media for presentation of the developed procedures to the user population. Mobile, self-propelled surface mine equipment requiring start-of-shift inspection was identified. Subsystems amenable to operational inspection were identified. The procedures addressing all safety critical subsystems on each equipment type were then developed and validated. The inspection procedures developed were those that could be performed largely from the operator's station. User acceptance was evaluated during on-site data collection visits to surface mines. Representatives of the user population reviewed the procedures and were then interviewed. Recommendations for the methods and media of presentation to the user population were developed from information obtained in: 1) Review and analysis of instructional technology literature applicable to this area; 2) On-site data collection; and 3) Analysis of the working environment and characteristics of the user population.

Jan 1, 1977

By Frederick Bloetscher

Means of improving the U.S. Bureau of Mines Brattice Window Method have been investigated by Goodyear Aerospace Corporation (GAC). An extensive series of laboratory tests at GAC and a series of tests in three operating coal mines of the Bethlehem Mines Corporation were conducted. The GAC laboratory tests defined the window coefficients and the accuracy of the method using different measuring techniques for a range of window sizes and shapes with window areas from 0.0873 to 4.0 square feet for flow velocities through the windows of from 100 to 1000 FPM. The results indicated that for the range of window sizes and window flow velocities investigated a single window coefficient value can be used with little error for each window size and for each flow direction, for the investigated range of window flow velocities. The mine tests developed techniques for quickly erecting the Temporary Test Stopping (TTS) in a cross-out, making the measurements, taking down the TTS and moving it and the test equipment to the next cross-cut. The time period for the total cycle ranged from 15-45 minutes depending on the properties of the cross-cut's surfaces. The total weight of the TTS and test equipment carried by the two miners conducting the tests was approximately 40 pounds. Correlation was obtained between the sum of the leakage values past 10 consecutive individual stoppings using the brattice window method and the value for the difference in the airway flow values before and after the 10 consecutive stoppings when the value for the sum of the leakages for the 10 was significant when com¬pared to the airway flow values. The mine tests reiterated the importance of using the largest TTS window(s) consistant with making accurate anemometer measurements for the best results with the brattice window method.

Jan 1, 1978

By Robert A. Miller

This computer program determines the price per ton of coal needed to obtain a profit of 12 percent discounted cash flow. From a predetermined equipment and manning list, the program calculates all costs and prints seven tables, Including the equipment and manning tables and the discount cash flow table. Forty-four of the input variables may be readily changed to study their effects upon the final price per ton of coal or upon individual cost items. The method is adaptable for any type of mining and with additions, for beneficiation processes. This program was written in Fortran IV for use on the IBM 11302 and with few modifications can be used on other computers.

Jan 1, 1971

By G. H. Wigton

This paper, describing the concentrator practice of the Chief Consolidated Co., is one of a series being prepared by the United States Bureau of Mines. The concentrator adjoins the town of Eureka, Utah, in the Tintic mining district. The Chief Consolidated, Eureka Lilly, Plutus, and Grand Central mines, all of which are owned or controlled by the Chief Consolidated Mining Co., are the principal sources of milling ore. The ore is transported from mines to mill by railroad. Although all the mines are within 3 miles of the mill, the railroad distance varies from 1 mile to 12 miles.

Jan 1, 1930

By Robert C. Merritt

This report describes laboratory as well as pilot heap leaching investigations of low-grade sandstone ores from Wyoming, New Mexico, and Colorado. Sodium carbonate-bicarbonate solutions containing sodium hypochlorite extracted up to 86, 54, and 16 percent U308 from Wyoming, New Mexico, and Colorado ores, respectively. Ammonium carbonate-bicarbonate solutions containing sodium hypochlorite were less effective at leaching these ores. Acid leach in replicate pilot plant testing resulted in U308 extractions of 96, 88, and 81 percent from the Wyoming, New Mexico, and Colorado ores. The development of cost-effective processes for extracting uranium from low-grade ore is essential to the assurance of a continuing domestic supply of uranium.

Jan 1, 1977

By Allan M. Johnson

Case histories were used to document and evaluate deficiencies in underground mine closures which have resulted in post-operation problems such as subsidence shaft failures, acid or toxic water drainage and others. Three different underground mining districts in the United States were investigated; 1) an iron mining district in Michigan 2) coal mining districts in eastern Ohio and southern Illinois and 3) three metal mining districts in central Colorado. Previous work in the Michigan district on problems with subsidence and acid water drainage provided the background from which the concept for this project was developed Student investigators working towards their MS degrees in Mining Engineering did the work on the eastern coal and western metal districts. The combined studies show that problems from acid water drainage, subsidence and inadequately protected mine shafts are the most severe and widespread. Suggestions of a technical nature are presented as partial solutions to some of these problems. It was determined that pre-closure evaluations could result in the identification of some potential problems that may occur after the mine is closed. Early recognition of these problems would be an advantage for at this time more options are available to the mine operator to either prevent them or to plan for their occurrence. Mine closure and reclamation should be considered as a part of mining and be incorporated in the mining plan. This would result in reduced environmental impact and would be achieved at a lower overall cost to the mining companies and to society. The role of water in the occurrence of several types of subsidence during mine flooding was significant at some mines in the Michigan district. These mechanisms which involve, friction reduction, gravity loading, overburden transport and hydraulic forces in a flooded mine probably have a broader effect than is currently recognized. Control of these processes may offer some interesting options during mine closure. It is recognized that technical solutions alone cannot provide all of the answers to problems associated with underground mines. Education, modified attitudes on the part of regulators and operators, and a more realistic perception of the importance and value of mining by the general public are also needed.

Jan 1, 1983

By P. M. Sullivan

A physical beneficiation flowsheet was designed by the Bureau of Mines for reclaiming and recycling metal and mineral values contained in municipal incinerator residues, and a continuous processing plant was installed. Residue samples collected from incinerators located in various parts of the country were processed at a rate of 1/2 ton per hour. Continuous screening, shredding, grinding, magnetic separation, and gravity concentration techniques were applied to produce metallic iron concentrates, clean nonferrous metal composites, clean fine glass fractions, and tine carbonaceous ash tailings. Research to develop systems for refining and upgrading the reclaimed metals and glass into marketable products is also underway. From the engineering data developed in the continuous processing plant, evaluations of the capital and operating costs for plants with capacities of 250, 400, 670, and 1,000 tons of dry incinerator residues per day were made. Research on a parallel system to separate and recover the metals, minerals, glass, paper, and plastics from raw, unburned refuse it currently underway, as are studies on the use of air classification to separate the refuse into organic and inorganic fractions.

Jan 1, 1971