Search Documents

By Rapheal Trousselle

For over 5 years, Davey Bickford has been developing and testing an electronic detonator blasting system. These new-technology detonators provide more accurate timing than conventional systems that rely on the combustion speed of a pyrotechnic composition.

Jan 1, 1997

By Richard J. Mainiero, Michael J. Sapko, Marcia L. Harris

Since 1988, there have been thirteen documented incidents in the United States and Canada in which carbon monoxide (CO) is suspected to have migrated through near surface strata into structures or other enclosed spaces as a result of nearby trench blasting or surface mine blasting. From these incidents, there are thirty suspected or medically verified CO poisonings and one fatality associated with these incidents. To better understand the variables contributing to this hazard, the National Institute for Occupational Safety and Health (NIOSH) carried out a small- scale field study to identify key factors that may contribute to the migration of CO through the ground. NIOSH conducted single- hole heavily confined experimental test shots to measure the radial pressure pulse as it propagated through surrounding monitoring holes to determine if a relationship existed between the pressure pulse and resulting CO measurements afterwards. NIOSH also monitored blasts at an airport construction site. Following the detonations, the concentrations of CO, nitric oxide (NO), and nitrogen dioxide (NO2) were monitored for several days in the surrounding satellite holes. The peak CO measurements relative to distances from the shots were compared. Pressure histories and peak particle velocities (PPV) were measured at monitoring boreholes. It was found that the differential pressures recorded within the boreholes give some indication as to the likelihood of CO appearing, whereas the PPV measurements do not seem to be as good an indicator for potential CO migration. In this limited study, changes in barometric pressure had very little influence on removing the trapped detonation products, whereas applying a vacuum to the monitoring holes was effective in reducing the entrapped CO concentration.

Jan 1, 2005

By L C. Taylor, H U. Lesiste

This is a preliminary study of the statistical variation of the pressures on a target above a buried explosion. The data were taken at various distances from the charge centerline for three heights of the target above the soil and one charge depth of burial. All tests were conducted in saturated sand. They show that peak pressures and times of peaks are neither repeatable from shot to shot nor rotationally symmetric within a single shot. The peak pressure and time of peak at each location can be represented by cumulative normal distributions. The paper describes the means and standard deviations of these distributions at eight distances from the charge center for each height of target. These are used to determine the change in standard deviation of the distribution with distance from the charge centerline and height of target. The effect of scale on the mean peak pressures and times of peaks and on their standard deviations at a single scaled distance from the centerline of the charge are explored using various charge weights.

Jan 1, 2010

By Unknown

Blast Site Security Involves: * Clearing the area * Controlling Access * Warning Signals

Jan 1, 2003

By Don Z. Painter, Gordon F. Revey

Frontier/Traylor Joint Venture is presently constructing a section of the Tri-County Metropolitan Transit District of Oregon's (TRI-MET) Westside Light Rail system. This new section will extend Portland's existing transit system to the western suburbs of Beaverton and Hillsboro. The drill-blast excavations at this project include 10,000 feet of 20 foot tunnel, 18 cross passages, three shafts, an underground railway station, and a U-wall open cut. From a blast designer's perspective, this job has been extremely challenging. Blast vibration is limited to 0.5 ips at 200 feet or at the nearest structure, and airblast is limited to 129 dB -- linear peak and 96 dB -- C scale. The tunnels pass under heavily built up areas and have top of tunnel to surface cover distances as low as 70 feet. Surface blasting in the 26,000 cubic yard U-wall excavation was limited to five short nighttime periods due to its proximity to the very busy highway 26.

Jan 1, 1995

By David Miller, James Santoro

Blasting is often required in urbanized areas to allow for economical execution of construction, demolition, and mining. Several examples of operations that require blasting in built up areas include: rock blasting for foundation and utility excavations; surface and underground mining for mineral extraction; and explosives demolition. Although explosives demolition is an engineering discipline, not at all like rock blasting, it still uses explosives for the felling of structures that have outlived their usefulness. Through the use of modem technology and implementation of extra safety precautions, explosives are used safely in congested areas to make the performance of critical work economical and feasible. This paper discusses several precautions required when undertaking various types of rock blasting and explosives demolition in congested areas. It also presents the adverse effects that must be considered when blasting in congested areas. The effects identified include flyrock, vibration and airblast, fumes, and non-elastic (permanent) ground deformations/overbreak. Measures for mitigating and controlling these adverse effects to provide on-site and public safety are presented.

Jan 1, 2000

By Scott Rosenthal, Logan Connolly

Butte, Montana holds a prestigious place in the history of mining, deemed “The Richest Hill on Earth,” containing a plethora of underground mines. The Orphan Boy/Orphan Girl underground mines, on the western side of Butte, operated from 1895-1956 producing zinc, lead, silver, and manganese. Today, the Orphan Boy mine is part of Montana Tech’s Underground Mine Education Center (UMEC) and the Orphan Girl mine houses the World Museum of Mining. Underground development in the Orphan Boy mine continues to progress as students from Montana Tech receive hands-on underground training; in addition, the UMEC is a multi-disciplinary research facility. Repeated underground blasting occurs in close proximity to old mine workings (wood supports installed circa 1950 or earlier). Research began to determine the impact of underground blasts on nearby pre-existing structures. Using the ISEE Field Practice Guidelines for Blasting Seismographs, one seismograph monitors the predominately-wooden structures to measure their response during each underground blast and one seismograph positioned on the surface to monitor surface structure response to the blast. This paper presents the findings of the research conducted to date for the project. The paper includes analysis of the research data, and conclusions determined from the research. Recommendations for the future work are included as well.

Jan 1, 2018

By Dominic Orf, Gregory Poole

On December 12, 2018 at 4:14 AM EST, an earthquake registering a 4.4 magnitude on the Richter Scale occurred in central Tennessee. According to a survey posted on the USGS website, this earthquake was felt throughout the southeast and even as far away as Arnold Nebraska. That’s over 900 miles (1,448 kilometers) from the epicenter. We recorded the vibrations from this earthquake on 44 different seismographs that were set up with remote access to continuously monitor vibrations from blasting activities. Having this data gave us an opportunity to compare the vibrations caused by earthquakes and blasting. A simple observation of the amplitudes, frequencies, and durations is enough to notice that vibrations from earthquakes are very different than vibrations caused by blasting in mining and construction. We were also able to observe the dissipation of the vibrations from the earthquake and see if the low frequencies, that are typical of earthquakes, dissipate at a consistent rate. Regression calculations were performed in order to see if there was a good data fit and if a specific vibration prediction could be made based on the magnitude of an earthquake. “How does quarry/mining/construction blasting compare to the Richter Scale?” This is a very common question that we get from homeowners when discussing vibrations due to blasting activities. This paper is intended to provide some simple answers for such a complicated question. Both the Richter and Mercalli scales are compared to the particle velocities as they were recorded from this earthquake.

By Gungor Tuncer, Ali Kahriman, Abdulkadir Karadogan, Mehmet Aksoy, Kagan Ozdemire

With increasing environmental constraints on the levels of disturbance induced by blasting operations upon nearby residents, there is an increasing need to be able to design cautious blasting with greater precision. Therefore, determination of maximum amount of explosive per delay for a certain distance especially in large blasts is of great importance for the elimination of these environmental problems. Although too many research studies had been carried out in the past in order to eliminate environmental issues produced from blasting unfortunately a general approach or formula has not been established yet because of the complexity of the matter. In addition to the wave and ground motion characteristics, the complexity of blasting parameters and site factors restrict the developing a general criterion. So experimental site-specific studies should be still done in order to predict and control blasting effects. This paper presents the results of ground vibration measurements carried out in Espey Open-Pit Boron (Colemanite) Mine located on the west side of the central Anatolia near Kütahya province in Turkey. Within the scope of this study, ground vibration components were measured for 13 shots during bench blast optimisation studies in order to predict peak particle velocity level for this site. In blasting operations; ANFO and Powergel Magnum 600 (blasting agent), Powergel Magnum (priming) and delay electric detonators (firing) were used as explosives. Parameters of scaled distance (charge quantity per delay and the distance between the source and the station) were recorded carefully and the ground vibration components were measured for all blast events using 4 different types vibration monitors (3 White Mini-Seis and 1 Instantel Minimate Plus Models). Then, the data pairs of scaled distance and particle velocity obtained from the 38 record events were analysed statistically. At the end of statistical evaluation of the data pairs, an empirical relation which gives average line at 95% confidence level and upper bound 95% prediction line with a reasonable correlation coefficient was established between peak particle velocity and scaled distance.

Jan 1, 2005

By Kurt Oakes, Paul Worsey, Braden Lusk, Tony Brasier, Scott Crabtree, Randy Wheeler

Theoretical description of destructive wave interference and the use of sacrifi cial holes is included and is supported by data collected at Springfi eld Underground. Finally, the process by which the reduction in vibration was achieved in practice is described. Results are discussed for several production blasts taking place over a one year period.

Jan 1, 2008

"Rock falls involving a relatively small amount of material are a leading cause ofinjuries in underground mines in the United States. A contributing factor is unwantedblast damage and over-break. A goal of the United States National Institute forOccupational Safety and Health is to reduce the number of ground fall-related accidents by improving drift driving practices through the introduction of perimeter control blast designs. This paper presents a blast design technique based on a hydrodynamic method. Using commonly available explosive and geometry data, the theoretical particle velocity is calculated as a function of distance away from a cylindrical charge. A calibration factor is introduced to account for actual conditions by comparing the predicted values to a set of field data. The calibrated curve can then be applied for design. The paper introduces modifications to account for different explosives from those used in a calibration test. The application of the approach is demonstrated with respect to a data set from a large-scale concrete block test."

Jan 1, 2009

By Joshua Taylor Drake

This report answers specific questions concerning underwater blasting considerations, and blasting safety. The blasting considerations discussed consist of basic blasting principles, and new variables to be accounted for. Blasting safety will include the safety of personnel and structures. The environmental considerations will also be discussed with mitigation methods. To be most effective, this document requires the reader to be familiar with key fundamentals of explosive engineering. In order for a blasting professional to benefit from this report, the following questions will be asked:

Jan 1, 2015

By Brian Micke, Mick Gavrilovic

The problem of rock hang-ups in underground mining operations has been a continuing one since the days of the “hang-up man”. This position commanded the highest pay of any underground worker in many historical Western U.S. underground bulk-mining operations, due to the occupational hazards of the job. Although underground mining techniques and especially work practices have changed greatly since then, the hang-up problem is a continuing one in many mines which use gravity flow of coarse rock in their transport systems or in those mines where stressed ground causes rock slabs to spa11 and bridge rock passes and stopes. In addition, with mechanized underground open-stoping mining methods now being used in many different types of ore deposits worldwide, this problem has again emerged as a very significant one in many of these highly mechanized operations. This is especially so where the remote operation of loaders is used for removing blasted rock from underground open stopes.

Jan 1, 1999

By Larry Schneider

Are you one of the thousands of hunters, fisherman, or hikers who purchased handheld GPS systems over the past several years and then been disappointed in their accuracy and performance. Or maybe you are one of the hundreds of blasters who have attempted to use GPS as a method for locating the exact position of their blast and measure distances from the blast to nearby structures. If so, you may have found that the accuracy of the handheld GPS systems left much to be desired. It may be time to get the units back out of storage and give them another try. As of midnight, May 1, 2000, the federal government has turned off the “error” built into the system known as “selective availability.” Here is a brief explanation of what that means in a question and answer format.

Jan 1, 2001

By James A. McGrath

"The predominant key word associated with all commercial blasting methods is “safety”. Safetyshould take precedent over all other aspects of the entire explosives industry which on a wholehas had an excellent track record as to number of injuries per unit of hours worked at all blastsites throughout our country."

Jan 1, 1999

By G. Hames, A. Drake, B. Sampson

The Timbarra opencut gold mine is located about 30 km(19 miles) southeast of Tenterfield in northern NSW some 4 hours by car from Brisbane, the capital city of Queensland in Australia. It was a small operation designed to produce about 40000 ounces of gold per annum utilising contract mining and company owned crushing plant feeding heap leach pads. This is a standard setup except that the mine owner was in charge of all aspects of drill & blast design even though a contract drilling & blasting (shotfiring) service was being provided. The major problem was that the blasting operations were yielding massive amounts of oversize due to the jointed partially weathered nature of the granite. This was adversely affecting all downstream aspects of the operation as well reducing gold output as ore boulders were being dozed over the side of the mine as they were impinging on mining productivity. The oversize problem had to be solved as the mine was struggling to achieve design gold output. Significant design & trialing effort using minesite resources were utilised to reduce the oversize but this failed even when powder factors up to 1kg/bcm(1.68lb/yd) were used. Dyno Consult from Dyno Nobel were therefore called to investigate, review & trial options to reduce oversize from the top flitch.

Jan 1, 2003

By C. Sawmliana, P. Pal Roy

Near-field blast vibration response of restrained pipelines either buried or exposed was studied during rock excavations at sensitive locations for Stage-II (4x500 MW) commissioning work in a super thermal powerplant of the National Thermal Power Corporation Ltd. (NTPC) of India. The existing running plant of capacity 1000 MW has many important installations including pipelines of varying diameters. These pipelines were very close to the blasting locations (mostly within 12m). Blast optimization and consequent monitoring of vibrations were carried out simultaneously for more than 250 experimental blasts conducted by the authors. This paper emphasized, particularly, on the safety of pipelines and their responses due to repeated blasting impacts. A few guidelines supported by theoretical derivations are provided for futuristic research.

Jan 1, 2001

By Seokbin Lim

In the design of explosives devices, an understanding of the behavior of explosively propelled matter is one of the most important steps in maximize the performance of these devices. For instance, an explosively driven metallic liner in LSCs (Linear Shaped Charges) creates its functional effect of penetration after a finite distance of travel (before collapse), thus the detailed study of the projection mechanism of the flat liner after detonation helps in the optimization of the design of LSCs. In a typical metallic flyer driven by explosive detonation, the detonation gas propels nearby matter including flat flyers. After a certain degree of expansion in the detonation gas, the flat flyer reaches its maximum velocity and slows down afterward. These typical behaviors are well investigated and numerically studied by many researchers. However, the rarefaction intrusion (detonation gas expansion) near the surface of the explosive charge creates significant deformation of the flat flyer , and produces U-shaped bending or deformation near the edge of the flyer during projection, creating unexpected behavior in explosive devices of interest. In this paper, a preliminary investigation of a localized Ushaped deformation of flat metallic flyers during projection is studied utilizing a theoretical approach and computational modeling facilitating an understanding of a general tendency of the deformation behavior.

Jan 1, 2010

By Adrian J. Moore, Alan B. Richards

Airblast overpressure levels can commonly be increased by up to 20 decibels (dBL) by the effects of meteorology, due to inversions and wind shear. Existing atmospheric refraction models can provide a good evaluation of the effects of meteorology, but have been limited in the accuracy of their outputs by the accuracy of the meteorological data that is available for input. This paper uses case histories from open-pit coal mine blasting in the Hunter Valley area of Australia to provide examples of increases in airblast due to inversions, wind shear, and a combination of both. It gives details of our experience of the accuracy with which predictions and assessments can be made using meteorological data of various levels of accuracy, and on the design buffer that is required to prevent the exceedence of airblast limits. The accuracy of meteorological prediction and assessment will shortly be improved by the use of sounding equipment that gives continuous measurements of temperature and wind velocity at significant levels above the ground. The paper also gives details of an industry funded research project that aims to permit the effective use of this data at distances many kilometres (km) (miles) from the location of the sounding equipment, and to develop a short term predictive model that will permit the amount of meteorological reinforcement that will occur at firing time to be determined before a decision is made to tie up a shot.

Jan 1, 2005

By Kristen Dunlap

There are several thousand remote stream crossing structures in the Tongass National Forest in need of removal. In 2007 thirty-three collapsing log bridges, log culverts, and metal culverts no longer in use were removed with explosives. Species of salmon, trout, char, and sculpin are present in the project area. Blasting overpressures may injure or kill fish in streams and ground vibrations can damage salmonid embryos in streambeds. Regulatory agencies offer guidelines with limits for blasting induced overpressures and vibrations. However, there has been no quantification of blast overpressures in shallow streams. Methods used to predict lethal levels for various blasting applications have not been completely validated. This research provides guidance for analyzing ground vibrations and water overpressures during blasting activities in or around fish streams.

Jan 1, 2009