Search Documents

By Zhou Jiahan Wang Feng

This paper introduces the mechanism and the operating process of dike building by silt squeezing blasting. DBSSB (dike building by silt squeezing blasting) has the following advantages: shorter construction period (the construction period is decided only by the speed of rock materials filling)greater consolidation of the body of the dike, more structural stability, smaller settlement. Therefore by conventional standards the same dike can be designed with a smaller cross section than other construction methods, and at a reduced cost when enough rock materials can be provided in site.

Jan 1, 2006

By Dirk van Zyl

Rock fabric information is often available from drill hole information and bench face mapping. An approach is presented to predict fragment size distribution of blasted material from this information as well as that obtained after the blast. The following information available from a mineral exploration drilling program was used in the prediction of fragment size distribution: largest piece, percent particles larger than 1 inch and RQD. Photographs of bench faces were used to estimate the fragment size distribution. Fracture spacings were evaluated along a series of parallel lines on the photograph. Photographic techniques were also used to obtain the grain size distribution of blasted material. m is paper describes the methodologies applied in some detail.

Jan 1, 1986

By Kenneth Eltschlager, Steven V. Crum, David E. Siskind

The Bureau of Mines was funded by the Office of Surface Mining (OSM) to determine how blast vibrations from a local surface coal mine were affecting homes in the towns of Daylight and McCutchanville, located in southwestern Indiana near Evansville. Although Daylight was about two miles from the blasting and McCutchanville four to five miles away, many residents claimed that blast vibrations were damaging their homes. At least one citizen felt that the vibrations worsened at the time the mine began cast blasting.

Jan 1, 1992

By Richard A. Dick

On August 3, 1977 the 95th Congress passed Public Law 95-87, the Surface Mining Control and Reclamation Act of 1977. This Act created the Office of Surface Mining Reclamation and Enforcement (OSM), which was given the responsibility of formulating regulations to implement the Act. This paper explains the rationale behind the specific provisions of the final blasting regulations, which were published in volume 44, No. 50 of the Federal Register, dated March 13, 1979. The major items covered by the regulations include preblasting surveys, blasting schedules, protection of the public, ground vibration limits, the scaled distance equation, airblast limits, blasting procedures, and record keeping. The regulations are designed to protect the safety and well-being of the public and to protect buildings and structures such as wells, pipelines, and storage facilities from damage.

Jan 1, 1979

By K Uenishi, H P. Rossmanith, N Kouzniak, A Daehnke

This contribution presents an introduction into that part of the field of elastic wave propagation which is relevant to blasting of boreholes and addresses briefly borehole breakdown and the formation of the fracture network around a borehole which ultimately leads to the disintegration of the rock mass. Phenomena of this kind are encountered in mining and quarrying. Numerical as well as experimental work referring to stress wave expansion from a detonating borehole is addressed.

Jan 1, 1998

By Kamal Wadhwa

Ever since the introduction of Liquid oxygen explosives in India in 1927, these explosives are being extensively used in the various mining industries such as coal, ironore, limestone, bauxite, magnesite etc. The earlier LOX compositions were based on cellulosic material of Weberlox series of French origin. They contained the basic ingredients of saw dust with an admixture of cork dust, some hydrocarbons and some metallic powders. However, there were some inherent defects in the soaking characteristics of these compositions, in as much as, absorption and retention of liquid oxygen in the cartridges were not properly regulated in the fine pores and in the inter-granular spaces inside the ingredients in a uniform manner.

Jan 1, 1989

By Brian Wingfield, Rick Givens, Greg Williams

Many technological advancements have been made in explosive products and applications over the last 15 years resulting in productivity and cost gains. However, the applications of total energy (engine horsepower) in the majority of rotary drilling technology, has remained virtually unchanged over that period. While advancements have been made in components, efficiency, and types of hydraulic systems used on drills, the application of current hydraulic technology to improve drilling productivity has not been interactive with end users. This paper will investigate how traditional design assumptions, regarding typical application of horsepower in current rotary drill systems, can actually limit productivity.

Jan 1, 1996

By Tassilo Baur

Explosives are used in the entertainment industry in a wide variety of applications. Live performances such as automobile races, air shows and the like have incorporated the use of explosives into their programs. Even art work has been created employing explosive materials and techniques. The primary entertainment use of explosives, however, remains in motion pictures, television, theater and related fields where it comes under the auspices of special effects. Much of it falls roughly into the category of demolition, though the object being demolished may range from a cigarette in a person's mouth or clothing worn by actors to large objects such as automobiles, aircraft, or boats. This paper will attempt to provide an overview of the materials and methods by which these special effects are created as well as highlight the unique problems encountered in this field and their often equally unique solutions.

Jan 1, 1992

By Jeffrey N. Deisher, H Y. Fang, Richard P. Scheller, Robert M. Koerner

The need to adequately quantify cracking in structures in the vicinity of blasting activity becomes more important each year. This urgency comes about through a growing number of complaints and lawsuits between the various parties involved, i.e., operator/owner, government, and complaintant. It is felt that existing rules and regulations (mainly based on peak particle velocity of the soil or rock adjacent to the structure in question) fall short of such quantification and lead to confusion in adequately assessing structural damage.

Jan 1, 1977

By Keith L. Bockelman

The Colowyo mine is a unique surface coal mining operation because it is a multiple seam pit. Using a combination of a shovel-truck and dragline operation, Colowyo mines 8 seams of coal to a depth of 400 ft. Over the past 3 years a number of operational changes have occurred, one of which is the implementation of blast casting. Through this implementation Colowyo has been able to eliminate over one million cubic yards a year, which would have had to be removed by the shovel-truck operation. This has also brought about a significant decrease in the stripping cost per ton within the dragline operation.

Jan 1, 1985

By Sanjay Sengar, Nabiullah Pingua, Saurabh Sahay

In India, more than 80 percent of the total of 557 million metric ton coal production comes from open-cast mines involving large overburden removal with average 1:3.5 stripping ratio which is going to in-crease in future. This operation consumes nearly 0.5 million metric ton explosives consisting of 80-85 percent bulk explosives and remaining 15 to 20 percent non-permitted large diameter explosives. Quali-ties of bulk explosives play an important role in rock blasting. Post blast results like poor fragmentation, tight mucking, toe problems, improper muck profile and lower productivity of mine may require chang-es in explosive loading factor (amount of explosive used per unit of rock blasted ). The explosive load-ing factor is an extremely important index to assess the economy of blasting operation.

Jan 1, 2014

By Dadan Munawar, Benny Gunawan

Blasting at Sebesi in Central Tutupan Pit area in South Kalimantan, Indonesia is planned to be using emulsion, where used oil makes up 50% of the total emulsion fuel. The significant amount of used oil from various mining operation units had been of deep concern since it might be reused to implement environmental programs by substituting 50% of fuel with used oil in emulsion, thus decreasing fuel consumption and increasing efficiency by reducing fuel cost. Used oil must pass laboratory test to meet the Indonesian National Standards (SNI) No. 7642:2010 of used oil specification. Other considerations include the location which is adjacent to the mine office facilities with a radius of <1,750 meters (5,741 feet). Thus, appropriate methods must be performed to meet the SNI No. 7571:2010 of vibration threshold in order to implement safe blasting technique and prevent potential damage.

Jan 1, 2015

By Leslie Taylor, R. Reed Skagga, William Gault

The ultimate aim of our overall task, of which the effort described in this paper is a part, is to be able to model the impulsive output of buried charges and the response of targets of interest. It is not practical or cost-effective to determine the response of all targets of interest to buried charges of all sizes by testing them. In order to have confidence in our models, however, they must be validated by a modest number of tests. A critical element in modeling the response of a target is the ability to model the loading function. The load a buried charge applies to a target above it when the charge detonates can be characterized in terms of the vertical impulse. The vertical impulse is a function of the size of the charge, its depth of burial, and the properties of the soil in which it is buried. The primary objective of the effort described in this paper is to determine the load a known charge places on a non-responding target so the data can be used to validate our models.

Jan 1, 2005

By Chad Ducey

The proper utilization of energy in an explosive column is of paramount importance to the success of any blast. Historically, Powder Factor (the weight of explosive per mass or volume of material to be blasted or its inverse), has dictated the blast design. The concept of Energy Factor is a more effective method to design a blast. In order to utilize explosives efficiently, the energy contained in any given product must be quantified. The Powder Factor method, although historically successful, assumes that a pound of cast pentolite affects the material to be blasted the same as a pound of ammonium nitrate / me1 oil (ANFO.) Years of experience and scientific testing have led the blaster in the field to believe otherwise. The next logical technological step is Energy Factor. The Energy Factor method that will be discussed in this paper takes into consideration not only the weight of the explosive, but also the weight strength (Cal/g) and the density (g/cc) to yield a constant relative Energy Factor. The result of such a method is a factor that can be used in the field exactly the same as Powder Factor, but that reflects the relative energy of any given product in terms that will reflect the relative cost benefit of that explosive selection. The Energy Factors associated with different available explosives make it possible to compare the difference in the amount of energy per loaded pound in each unit length of borehole. This paper will examine the concept of Energy Factor in an in depth manner and also compare this quantification method to that of Powder Factor. It will also demonstrate the value of using Energy Factor and how it can improve the efficiency of a blast design. The misconceptions that come along with using Powder Factor will be examined and comparisons will be made between boreholes loaded using Powder Factor and those that are loaded using Energy Factor. This paper will clearly define the differences between these blast design methods and allow the reader to realize the production, quality, and economic advantages of using the Energy Factor method.

Jan 1, 2000

By W Russell

The Hercudet Non-Electric Delay Blasting Cap System provides a means of achieving greater flexibility in the use of delays, using totally enclosed gas detonation circuits which eliminate the concussive effects of detonating cord trunklines in the confinement of access tunnels beneath pillars of ore. This is an account of one such pillar blast.

Jan 1, 1985

By Jason M. Ryan, T Michael LeBlanc, John H. Heilig

"Drill trajectory deviation is a recurring problem in vertical retreat stoping operations. As a result of thisdeviation, 60 kilogram (165 millimetre diameter) and 103 kilogram (203 millimetre diameter) explosive charges are routinely detonated beyond ore/waste contact zones. Consequently, there follows a reduction in finished stope wall stability and an increase in ore dilution."

Jan 1, 1996

"In order to increase control over blasting, it is important to identify the imperative mechanismsand to quantify their participation during the rock fracturing process. The useful energyreleased by the detonation of an explosive is split into shock and gas energies. The relativeimportance of these two energies in the rock fracturing process is still an area of active debate."

Jan 1, 1999

By P. Katsabanis

Numerical modelling was used to examine damage in wall control operations. Decoupled charges appear to create larger damage zones than fully coupled low density charges with similar charge distributions: Air was shown to be a very efficient coupling medium, while water coupling resulted in significant damage. However, Mach stems are formed when air is used as a decoupling medium, leading to compression of the charge ahead of the detonation wave. Air decked charges generate two damage zones, one close to the charge and another close to the air-deck/stemming interface, where pressure pulses are reflected. The extent of the latter depends on the length of the air-deck.

Jan 1, 2001

By Chantale Doucet, Yves Lizotte, Alan Cameron

A joint Federal Government-Industry research project on the effect of geology on the fragmentation of rock excavated by blasting in underground developments was conducted at the CANMET Experimental Mine, near Val d’Or, Quebec. A total of thirteen (13) blasts were studied from November 1994 to February 1995. The analysis of each blast was divided into three stages: pre-blast characterization, including structural mapping, assessment of Rock Mass Ratings (RMR), Tunneling Quality Indices (Q), blast design documentation; blast characterization comprising blast vibration monitoring and analysis; and post-blast assessment comprising fragmentation assessment by digital photoanalysis, calculation of half cast factors and measurements of bootlegs.

Jan 1, 1996

By V R. Sastry, D P. Singh, N R. Thote

Rock parameters which are uncontrollable impose restrictions on the procurement of desirable fragmentation. Blast design parameters which are controllable prove to be important tool in blasting operations. An attempt was made by the authors to investigate parameters which causes big oversize boulders in overburden blasting. A case study of coal mine is discussed in this paper.

Jan 1, 1995