Search Documents

By Minoru Kawamora, Koichi Kurokawa, Kenji Hashimoto

We developed concentrated remote control blasting system to blasting simultaneously at a large number of sites in a mine of large scale. This system is consisted of three parts, the first part is a control station with high voltage power source units, the second part is a relay terminal with relaying and branching units, and the third part is a blasting machine with charging and discharging units. The control station is connected with the blasting machine by mean of control bus wire. The blasting machine adopts MBS(electromagnetic induction blasting system) for the reason of safety and good handling.

Jan 1, 1990

By David Kosnik

This paper describes the technology and methods deployed in the continuous autonomous remote monitoring of cracks in interior and exterior walls of a residence near a limestone quarry. The objective is to quantitatively compare crack response due to blast-induced ground motion to that induced by diurnal temperature changes, weather fronts, occupant activity, and other phenomena. The remote monitoring and communication technology developed to obtain and disseminate crack response data for this study may provide the means to mitigate the effect of public concerns about potential impacts of ground vibrations inherent in construction and production of raw materials; it is critical to address these concerns because subsequent litigation may result in delays and increased costs.

Jan 1, 2009

By Andrew F. McKown

This paper will discuss the mechanisms of potential damage from close-in construction blasting, concentrating on two mechanisms: elastic ground vibrations and non-elastic (permanent) ground deformations. The latter will be shown to be the most dangerous for close-in blasting. With respect to elastic ground vibrations, discussion will center on the differences in vibration frequencies and impacts between typical close-in construction blasting and typical mine and quarry blasts, and how using vibration criteria derived for residential structures near mines can lead to very conservative criteria for close-in construction blasting. The effects of high frequency vibrations seen in close-in blasting will be commented on. Factors affecting the magnitude of ground motions will be discussed. Simple, practical techniques will be presented to minimize the potential for damage from close-in blasting, by minimizing the potential for rock block movement or ground heave. Case histories will be presented to illustrate some of the techniques discussed, and give examples of successful close-in blasting projects.

Jan 1, 1991

By Carl Hendricks

AQUILA Mining Systems Ltd. is the world leader in drill monitoring, control and GPS based drill navigation systems for the mining industry. This paper will review the general design and application of AQUILA.s drill systems currently in use throughout the world and the key benefits that derive through their use.

Jan 1, 2002

By Michael McDougall

"Suncor Inc. Oilsands Group, Mining Operation in Northern Alberta, Canada, has beenblasting to loosen the oilsands to increase production and decrease maintenance of the hugebucketwheel excavators for over twenty years. In 1991 an area of the mine wasencountered which had a working face in excess of 130 feet. In order to maintain theproduction objective, the blasting department took on the task of providing as much of ablasted face to work with as possible. In doing this Suncor has exceeded several knownrecords in production blasting."

Jan 1, 1993

By Peter N. Calder, John N. Tuomi

The development of a successful control blasting program for an open pit iron mine in hard jointed rock is described. The objectives and mechanics of control blasting are discussed. Design and implementation procedures, which should have wide application, are given. Small diameter angle hole pre-split blasting, buffer blasting with production holes in front of pre-split lines and in front of strongly defined rock structures, and vibration control of production blasts are dealt with.

Jan 1, 1980

By Michael Noy

Current image based systems used to measure fragmentation are measuring the two dimensional presentation of a set of three dimensional objects. A two dimensional measurement of fragmentation restricts both sampling and particle size classification and hence provides a different evaluation of the fragmentation to that of a conventional sieve analysis of the same sampled material. Many modern image based fragmentation measurement systems attempt to convert this two dimensional analysis to a three dimensional analysis in order to deliver a "real" measurement of the fragmentation distribution. This paper questions the necessity and validity of this transformation and lays down the framework for the establishment of a standard in fragmentation measurement based on a two dimensional analysis. The results of image based measurements of laboratory prepared samples indicate that differences in mass distributions (3D distribution) can be mapped by an appropriate image based analysis which provides area versus particle size information.

Jan 1, 1997

By Richard J. Mainiero, Michael S. Wieland, Harry C. Verakis

The Bureau of Mines, U.S. Department of the Interior, has been conducting research on delay blasting in underground coal mines in support of the efforts of Mine Safety and Health Administration (MSHA), U.S. Department of Labor, to revise coal mine blasting regulations. Part of the research centered on developing an understanding of the factors that lead to misfires of permissible explosives. Research was conducted to determine whether frequency of misfires was related to borehole spacing. For a wide variety of permissible explosives, misfires were observed for about 50 X of the holes at 45-cm (18-in) spacing. Misfires were also observed for 60-cm (24-in) spacing, but the frequency of misfires was much lower than observed for the 45-cm (18-in) spacing. The Bureau has recommended that hole spacings of less than 60 cm (24 in) be prohibited.

Jan 1, 1986

By Ashlin Pillay, Osamu Iwata

Hong Kong is ranked as the world’s third most important international financial hub and attracts significant growth and development annually. The city is also known as the world's most vertical city, the most common view from your window in Hong Kong city centre is probably the window of another 30 storey skyscraper. The increasing demand for real estate in this bustling Metropolis has placed immense pressures on its transportation infrastructure because whilst the construction continuously grows upward with larger and larger skyscrapers, it leaves the transportation planners with very little choice but to go underground. As a first world city, interrupting daily business operations is simply not an option; however, of even greater concern is the safety of these 8 million residents. Blasting Regulations are under the strict control of the Mines Division showing zero tolerance to the breaching of safety standards. The Ho Man Tin Station (HOM) excavation, a part of the Kwun Tong Line Extension (KTE) project situated in Hong Kong began in June 2012 and is one such project that is under strict regulations from the Mines Division. The HOM project is a cross cut interchange station between the Kwun Tong Line Extension (KTE) and Shatin Central Link (SCL).

Jan 1, 2015

By Gungor Tuncer, Ali Kahriman, A. Kadir Karadogan, Savas Gorgun

The environmental problems arisen from ground vibration and air blast have been faced and discussed frequently in various industries such as mining, construction, quarry, pipe line etc. where blasting is unavoidable operation. Structural damage due to ground vibrations creates great socio-economic problems for mine and quarry management as well as for the people residing in its vicinity, therefore in bench blast design, not only the technical and economical aspects, such as block size, uniformity and cost, but also the elimination of environmental problems resulting from ground vibration and air blast should be taken into consideration. With the general trend towards larger blasts in mining and infrastructure excavation, ground vibration and air blast problems and complaints have significantly increased. With increasing environmental constraints on the levels of disturbance induced by blasting operations upon nearby residents, there is an increasing need to be able to design cautious blasting with greater precision, therefore determination of maximum amount of explosive per delay for a certain distance especially in large blasts is of great importance for the elimination of these environmental problems. In another word, prediction of ground vibration components is extremely important for the minimisation of the environmental complaints. Estimating of particle velocity and other components of ground vibration with reliable approaches will give important facilities to the blasters. Although many studies had been carried out to isolate environmental problems induced by blasting in the past, a general reliable formulae has not been established yet. Due to restrictions on the complexity of ground motion, blasting and test site factors, experimental studies are still necessary for each site to minimise environmental issues. This paper presents the results of ground vibration measurements carried out during the excavation activity for contruction of an organised industrial region located nearby Istanbul in Turkey. The major rock type is granite that is encountered at this site. Within the scope of this study, in order to predict peak particle velocity level and produce a site-specific propagation curve for this site, ground vibration components were measured for blast events during bench blast optimization studies over a long period. In blasting operations; ANFO (blasting agent), gelatine dynamite (priming) and delay detonators (firing) were used as explosives. While the parameters of scaled distance (charge quantity per delay and the distance between the shot and the station) were recorded carefully, the ground vibration components were measured by means of two different vibration monitors for every event. Then, the data pairs of scaled distance and particle velocity were analyzed. The equation of scaled distance extensively used in the literature was taken into consideration for the prediction of peak particle velocity. At the end of statical analysis and evaluations an empirical relationship with good correlation was established between peak particle velocity and scale distance for this site.

Jan 1, 2000

By J R. "Dick" Daniel

Over the past several years, the Hercules Technical Service Group for the Explosives Department has produced a series of programs for the TI59 programmable calculator dealing with explosive application problems. These programs have been made available to both our internal staff and to the Hercules explosives distributor organization. Several of these programs have found good acceptance and wide usage.

Jan 1, 1984

By Calvin Konya, Janos Foldesi

A bridge over a main line railroad system was scheduled for demolition. The bridge was made of reinforced concrete and spanned three mainline railroad tracks which could not be shut down due to blasting or demolition. To further complicate matters, the mainline tracks had high tension power lines running above the tracks, but below the bridge. These high tension wires provided the electricity for electrically powered trains. The tracks could not be damaged or disrupted, nor could the power line be broken.

Jan 1, 1992

By Jerry R. Wallace

This project consisted of blasting for expansion of a major interstate natural gas transmission pipeline pump station. The pump station handled 400-500 million cubic feet (11-14 million cubic meters) of gas per day.

Jan 1, 1996

By Joshua Hoffman, Catherine Johnson, Braden Lusk

The practice of dual initiation using precise timing from electronic detonators in boreholes is thought to be beneficial for increasing fragmentation at a desired location in the rock strata. This increased capacity for fragmentation is understood to be a product of both the collision of detonation waves in the explosive column and an increased energy liberation rate, each resulting from dual initiation. In addition, the collision of shock waves from two adjacent blast holes is suggested to improve fragmentation at the location the two shock waves meet, which can be controlled with precise timing. This paper presents the results from scaled laboratory experiments where converging detonation waves and shock waves were studied.

Jan 1, 2014

By Bob de Raadt

For a long time industrial underwater blasting has stood in need of a calculation method, for the determination of shockwave-proof as well as shockwave-effective charge distances to objects in water. After a brief discussion of the physical background of the shockwave mechanism in water, the author discusses an empirical theoretical computing method based on the "Bubble boundary" concept. The practical application of this model is finally shown in an account of a few underwater blasting operations in which charge weights of c.1-1000 kg were involved.

Jan 1, 1980

By L. O. Souza, J. F. Gewher, M. P. Scussiatto, C. S. Mendonca, R. A. McClure, B. T. Kuckartz, J. Kloeckner

Blasting is the most effective and economical tool available to fragment and move rock for most applications. If properly executed, it can improve down-stream operations such as loading, hauling and crushing. It is not possible, however, to have full control over the energy released by the explosives when a poorly designed blast pattern is used. A poorly designed blast can produce serious damage to equipment and create a potentially hazardous condition to people. Advanced mining technology has been developed to address these potential hazards and optimize the blast pattern. This profiling technology can assist with blast planning and provide quick, precise data about the condition of the rock structure to be blasted. The 3G BlastMetrix system presented here uses three-dimensional (3D) stereo photogrammetry to model the rock mass in a fast, practical and safe manner. Through the image overlapping method, a 3D model is created with thousands of points that provide a significant amount of data regarding geology, geometry and topography conditions. The blasting plan can then be made in a way to optimize the rock fragmentation and avoid areas that could create flyrock. This paper is a case study concerning usage of stereo photogrammic surveying and borehole survey systems in a blasting operation at the Brazilian Quarry, Incopel. One 3D image of a drilled bench was generated using photogrammetry survey technology and the borehole survey data collected using the rodded Boretrak borehole survey system. Utilizing the minimum burden profile reports, explosive loading could be done accurately, resulting in an optimized blast with good heave and fragmentation as well as increased safety.

Jan 1, 2013

By Minoru Kawamura, Koichi Kurokawa, Yukio Kato, Kenji Hashimoto

It is well known that ground vibration by blasting is mainly related to a distance and charge weight. However, it is not known the correlation between ground vibration and performances of explosives; for example, shock wave energy, bubble energy, detonation velocity and ballistic mortar value etc..

Jan 1, 1991

By D K. Joyce, B Mohanty

In a previous paper, it was shown that a lack of clear understanding of the role of initiation mode on detonation characteristics often leads to under-utilization of the explosive system in blasting. This is of particular significance since the very large number of explosive initiation practices currently in use implicitly assumes that the blasting performance of an explosive is largely independent of the exact mode of initiation. This paper deals specifically with bulk-loaded and pneumatically-loaded ANFO under various initiation modes in small diameters. These include initiation by booster and detonating cords of various strengths, and combination of cords and boosters. The nature of energy release and energy partitioning between shock and gas energy have been studied in the underwater test as a function of charge diameter. The paper describes the relative merits of various initiation modes for specific charge geometries and confinement, under end- and side-initiated conditions. Guidelines have also been formulated for use in the field to match initiation practice with blasting requirements.

Jan 1, 1994

By Doug Anderson

Two quantities, Peak Particle Velocity (PPV) and Scaled Distance (SD), have controlled aspects of many blasting projects and operations for a long time. Vibration criteria typically use both PPV and SD because they are simple to measure, and simple to calculate. Their use in regulations worldwide is fairly ubiquitous, in efforts to limit damage to structures in the neighborhood of a blasting operation. PPV and SD are also used to determine likely blast damage effects in mining operations.

Jan 1, 2018

By Lina Lopez, Jose Sanchidrian, Manuel Lopez, Pablo Segarra

Previous work in which rock properties and blasting parameters (geometry, charging and timing) were reported together with truck filling times, is taken as a starting point for a thorough analysis of the influence of the former on the mucking velocity. The experimental set was composed by 11 blasts made in an open pit mine. Non-parametric, distribution-free statistics is applied. The mucking rates (in bank cubic meters per unit of bucket volume and per hour) appear to be clearly dependent on the explosive energy and powder factor, both magnitudes combined as energetic powder factor (energy per unit of rock volume). The mucking rate is a non-monotonic function of such factor in the range of the blasts analyzed. The determination of the function is optimum when the fraction of the explosive below grade is not considered and when the explosive energy is qualified as that delivered at a partial detonation regime. Different types of loaders seem appropriate for different energy levels. At low levels both front loaders and rope shovels obtain small productivities without a statistically significant difference in their performance. At high energy levels, front loaders qualify higher than rope shovels. Mucking velocities can be equally small at low energy powder factors and at high ones if rope shovels are involved.

Jan 1, 2008