Search Documents

By D. W. Lui

Tangdan copper oxide deposit, the largest independent copper oxide deposit in China so far, is located in the northeast of Yunnan province, southwest of China. The ore from this deposit is characterized by: low grade, high oxidation ratio, and fine-grained disseminated, resulting in poor flotation recovery. The analysis of plant flotation data reveals that the loss of copper minerals into tailings is mainly with coarse size fraction due to insufficient liberation and fine size fractions, especially minus 10 microns fraction, which proved to be very difficult-to-float with conventional flotation. In order to improve the performances of plant flotation of this ore, laboratory flotation tests were conducted with the pure malachite, which was the principle copper oxide mineral in Tangdan copper ore deposit. The results obtained suggested that a finer grinding (up to -325 mesh or even -400 mesh) be needed to decrease the loss with coarse size fraction, and vacuum flotation is a promising way for the recovery of the fine malachite effectively.

Jan 1, 2014

By Y. S. Song

Flotation separation of galena, sphalerite with pyrrhotite in ethanoic acid + sodium acetate sys-tem was studied in this paper. The flotation tests show that galena and sphalerite can float but pyr-rhotite can hardly float in the pH range of 3.6 to 5.6 in ethanoic acid + sodium acetate system. The flotation tests also show that galena can be separated efficiently from pyrrhotite and sphalerite can be separated on the whole from pyrrhotite, but the separation efficiency of the former is much better than the latter. The flotation results have been investigated by ultraviolet spectrum and XPS analysis, and explained by theory of hard and soft acid and base (HSAB), hydrogen bond and galvanic coupling.

Jan 1, 2014

By V. Sheikhzadeh, M. Saghaeian, R. Hejazi, A. Abazarpoor

Green pellet strength including drop number and green compression is highly depended on particles size and shape. The used grinding method, ball mill or high pressure grinding roll (HPGR), directly vary the particle size and shape. Considering mode of pellet crack, green pellet is composed of particle-binder-moisture system. Different type of forces existed in such a system to create a stable green pellet: solid particle interaction, magnetic, binding and cohesive forces in the interface of particle-moisture. The pellet failure can occur at solid-liquid interface and/or through liquid phase. Pellet crack occurs when crack passed through entirely the plane failure. In this research, the effect of particle size and shape of pellet feed on green pellet strength has been investigated. It was deduced that green pellet strength highly improved by increase of specific surface area. The drop number and green compression strength of pellets prepared by HPGR was higher than ball mill. It was found that the main reason responsible for this difference was the particle shape. Capillary force is responsible for part of pellet force and improves by decrease of particle size. Also more elongated shape of HPGR particles resulted in higher capillary force due to thinner interface layer between particles. The less circular shape of particles lead to improvement of capillary force as can be occurred for HPGR particles. The rougher shape of HPGR particles resulted in higher wettability of particles and better diffusion of water among particles. In fact the rougher particles means lower connection angle. Aspect ratio of particles was of great importance of crack growth because the required energy of pellet failure increases directly. The required energy for pellet failure increases by increment of particle aspect ratio. The relationship among crack failure force, roughness and aspect ratio has been modeled considering 3 shape descriptors.

Jan 1, 2018

By Mohammad Noaparast, Hamed Haghi

"In this research work, it was attempted to reduce the iron contents (Fe2O3) in relatively low grade silica sample which was obtained from Shenin silica mine, using magnetic separation. The prepared sample contained 93.75%SiO2, 0.44%Fe2O3, 2.78%Al2O3, and 0.08%TiO2 and the Fe2O3 had to be reduced to less than 0.08%. Mineralogical studies and XRD analysis indicated the presence of Hematite, Pyrite, and Goethite as the major iron impurity phases. Mineralogical studies of polished and thin sections demonstrated that the degree of freedom of silica is more than 80% in -300+212 ?m size fraction. After primary stages including crushing, milling, scrubbing and de-sliming, various methods such as low intensity magnetic separation (LIMS), high gradient magnetic separation (WHGMS) and dry high intensity magnetic separation (DHIMS) were applied to find out that which process would be appropriate for the elimination of iron impurities from this sample. Different experiments were carried out on the product of wet rod mill and scrubber. However the magnetic field intensity of WHGMS was increased down to 2Tesla, and there was not any acceptable result in reduction of Fe2O3 content lower than 0.08%. Thereafter the product of wet rod mill and scrubber were dried and reported to DHIMS. In these experiments, maximum magnetic field intensity was 1.4Tesla. In this case very significant results were achieved, and Fe2O3 content of final product were reduced to less than 0.05% which meets glass manufacturing standards."

Jan 1, 2014

By Y. H. Tang

For its surface features, micro-sized hematite is usually difficult to recover by magnetic separation; especially, the existing high gradient magnetic separator in industry can not utilize collecting matrix with thin silky rods for its property of being easily blocked; the lower size limit for recovery of micro-sized weak magnetic minerals is about 0.019mm, some even is 0.037mm. This paper introduces the application of the combined new technique of water-air joint discharging of concentrate and collecting matrix with different diameter silky rods in the field of recovery of micro-sized hematite by high gradient magnetic separator. The commercial test result for recovery of a certain hematite with size about ?0.037mm shows that the recovery can be promoted by 16.81% with basically same concentrate grade.

Jan 1, 2014

By Ventsislav Stoilov, Angel Angelov, Ivan Korolev, Antti Remes, Todor Pukov, Stoyan Gaydardzhiev

"The process modeling and simulation studies aim for better process operation and favorable environmental impact. The objective of this work is to set up a simulation model of the Assarel copper flotation circuit for planning and optimization of the process with the aim of increased metal recovery. The model is parameterized based on laboratory flotation tests of ore samples from the Assarel mine together with mineralogical studies by X-ray diffraction (XRD) and Mineral Liberation Analysis (MLA). A combination of several techniques allows reliable identification of mineralogical composition of the selected samples. The changes in the proportion between sulfide minerals in various products along the circuit have been also documented. Further, this information is used in the simulation model and in data reconciliation procedures for establishing mass balance. The simulation accuracy is studied by comparing the simulations with the plant survey based mass balance. Constructed simulation model can be used to run alternative process scenarios. As an example, the flotation circuit performance with different reagent regimes is simulated based on data from batch flotation tests. Two reagents were considered for this purpose, dithiocarbamate-based one and xanthogen formate/mercaptan blend. It has been revealed that these reagents do not have the same influence on the selective flotation. The one improves flotation of gold and overall recovery but without notable selective action. In contrast, the other showed better selectivity towards copper, rejecting more gangue and lowering gold recovery. The model is also applicable for process optimization studies with different feed compositions, flowrates and circuit configurations. INTRODUCTION In the pursuit for elevated technological indicators, finding an optimal set of process parameters fully utilizing the potential of the equipment is a key factor to success. Over the past decades, there has been a substantial development in flotation circuit optimization through performance benchmarking using metallurgical modelling and steady-state computer simulation. Practical simulation engineering tools are based on experimental data obtained from laboratory tests and from plant surveys and operation data. With the help of flotation models, it is possible to study grade-recovery response with different feed compositions and throughputs, and with various cell-operating parameters, as well as to evaluate and design different flowsheet configurations. Outotec’s HSC Chemistry® software, which incorporates simulation and mass balancing modules alongside with several other tools, can assist with this optimization (Mattsson et al., 2015)."

Jan 1, 2018

By Bertil I. Pålsson, Sture V. Persson, Kent T. Tano

"Grinding is one of the most energy consuming unit operations and is also a very inefficient and costly process. Therefore, it is of great importance to run the grinding process as efficiently as possible. The most common way today to control grinding processes is by measuring the power draw of the mill and try to keep it at a maximum level. However, some studies (Kawatra, 1989, Koivistoinen, 1989, Moys, 1989) have shown that this measurement doesn.t reflect everything that takes place inside a mill. Among other parameters like slurry rheology, temperature and charge behaviour, the volumetric filling of a grinding mill seems to have a large influence on the grinding efficiency (Herbst, 1988, Koivistoinen, 1992, Vermeulen, 1988). A problem in attempting to measure those parameters has been to get a sensor that is both robust and sensitive enough for continuous on-line measurement.This paper presents a method for the measurement of the apparent filling level in a pilot ball mill equipped with the Metso Continuous Charge Measurement system (CCM). In this technique a strain gauge sensor is mounted on a flat steel spring which is fitted into a recess underneath a lifter bar. In addition, a conductivity probe, the Boliden Grinding Measurement System (GMS), is mounted in another lifter bar with the purpose of comparing the two measurements. To visualise the behaviour of the charge a DEM modelling technique is used.The results indicate that the system is capable of following the normal variation that occurs in the mill. The signal also very well reflect changes in operating variables such as ball charge level, pulp density and rotational speed. By studying the nature and different features of the signal one can get a better understanding of milling circuit dynamics. Another feature of the technique is the possibility for an operator to continuously follow the grinding process and thereby run the process under optimal conditions."

Jan 1, 2003

The ultimate goal of a mineral processing plant is to recover as much of the target mineral(s) as possible from the ore being treated to achieve the best economics. Selection of the mineral processing techniques is the most important step in achieving this goal. However, due to the complexity of the ore, the recoveries of valuable minerals may be not satisfactory even when the mineral processing technique(s) are well chosen. In other words, minerals of interest can be lost to the tailings for mineralogical reasons. For example, gold is mainly extracted from the ore by gravity, flotation, cyanidation, or a combination of these processes, and high recovery (>90%) can be achieved when gold occurs as coarse grains. However, when a refractory ore is being processed, gold extraction will be challenged by mineralogical factors, which often cause gold losses to various tailings. Mineralogical factors affecting gold recovery mainly include grain size, shape, surface coatings and rimmings, presence of cyanicides, oxygen consumers and preg-robbers, presence of slow-dissolving gold minerals and the refractory nature of submicroscopic gold. Among these factors, locking in sulphide, silicate and other minerals as fine-grained gold inclusions and/or as invisible submicroscopic gold is by far the most common factor leading to poor gold recovery encountered in gold ore processing. Processing of PGE ores faces the same challenges as gold. Small grain size and locking of PGM in sulphide and non-sulphide minerals often cause PGM losses. When silver ore contains significant amounts of pyrargyrite, proustite and stephanite, silver recovery by cyanidation can be very low because of the slow dissolving kinetics of these minerals. In the processing of base metal ores, high content of pyrite, intergrowth of chalcopyrite with sphalerite and presence of clay miner-als may cause problems in recovering Cu-, Pb- and Zn- bearing minerals. Process mineralogy helps address all issues and problems related to mineral processing with predicting and trouble-shooting being two major objectives. It provides useful information on process selection, flowsheet development, recovery improvement and reagent consumption optimization. The information acquired from a process mineralogical study can be used as a guide for a metallurgical testwork program for process design or optimization.

Jan 1, 2014

By X. Q. Ma

The beneficiation test on low grade phosphate ore from a state of Russia is carried out. The rougher-cleaner ? re-cleaner system is used in the flotation process, The fineness of grind is 39.07% minus 200 mesh. The result indicates that concentrate containing 31.25% P2O5 can be obtained from the flotation feed assaying 6.18% P2O5, with 93.54% P2O5 recovery. The test result is also a guideline for further development of some currently operated phosphate beneficiation plants.

Jan 1, 2014

By V. Hudecek

Problems of sudden outbursts of rock and gas present in deep mine mining ones of the most complicated interrogation. It is searching for the methods of prediction and prognosis that can be most useful for the government of these phenomena. Till now the pressure and the desorption of gas in bore holes was consider to be the decisive criteria. By the work of authors with using of statistical date was verify that for considerable reliability of forecast and prevent outbursts is necessity investigate characteristics of workplace and other indicators. These indicators were analyzing and assemblage into mathematical dependences which represent active and passive force asserting with in the process of rush. It was validated by using the equations which are presented in the manuscript that the accuracy of pre-diction of the phenomena is higher and methods of preventions are better also.

Jan 1, 2014

By C. G. Anderson

Industrially proven and applied nitrogen species catalyzed (i.e. NSC) acidic pressure leaching has been utilized to treat a number of ores, concentrates and recycled materials. This versatile technology offers many advantages including low temperatures, low pressures, low capital costs, low operating costs, faster throughput and less costly materials of construction than conventional pressure oxidation. This paper will elucidate the application of this technology for production of gold, silver, palladium, rhodium, zinc, germanium, gallium, cobalt, copper, molybdenum, rhenium and nickel. Recycled material applications will also be elucidated. In addition, details of an application for treatment of a refractory chalcopyrite copper and gold bearing ore will be presented and pertinent economics discussed.

Jan 1, 2014

By Jie-Liang Wang, Yongdan Cao, Zhao Cao

"The effect of ethylenediamine tetraacetic acid (EDTA) on flotation separation of fluorite from bastnaesite and its selectively depression mechanism on fluorite were studied by single mineral flotation, artificial mixed minerals flotation, solution chemistry analyses, Zeta potential and XPS measurements.The results show that fluorite can be deeply depressed by EDTA while the flotation of bastnaesite is almost unaffected when octanohydroxamic acid (OHA) is used as a collector. The separation index (SI) between bastnaesite and fluorite increases with the dosage of EDTA, SI can be raised from 1.18 to 12.66 when EDTA dosage increases from 0 to 2×10-3mol/L.Solution chemistry analyses show that EDTA is able to convert the Ca(OHA)2 hydrophobic precipitation on fluorite surface to a soluble Ca-EDTA complex but cannot complexly dissolve the Ce(OHA)3 precipitation on bastnaesite surface. Therefore, the Zeta potential of OHA conditioned fluorite can be reduced significantly by EDTA while the reduction degree to Zeta potential of bastnaesite is relatively low. XPS measurement shows that EDTA removes the chemically adsorbed OHA from fluorite surface but has little effect on the adsorbed OHA on bastnaesite surface. As a result, fluorite can be selectively depressed by EDTA in bastnaesite flotation, which behaves an important industrial application prospect in rare earth ore flotation.INTRODUCTIONNowadays, Rare earth elements (shortened as RE) and compounds are of significant importance for a range of rapidly expanding industrial applications including catalysis, metallurgy, renewable energy, and special materials due to their unique electrical, magnetic, optical and chemical properties [1]. The seventeen RE elements, including the lanthanide-group fifteen elements, yttrium and scandium, could be divided into three groups, i.e., light, medium and heavy RE elements based on the different solubility of RE sulfates [2]. Bastnaesite ((Ce,La)CO3), containing approximately 75% REO, is one of the most important light RE minerals [3]. Flotation is the common method to recover basetnaesite [4-6]. Nonetheless, basetnaesite is often associated with calcium-bearing gangue minerals such as fluorite, and the separation of basetnaesite and fluorite by flotation is usually difficult due to their similar surface properties and therefore floatability [7-9]. Therefore, research on high selective flotation reagents of bastnaesite over gangue minerals has attracted a lot of attention [10]."

Jan 1, 2018

By Peter M. Solozhenkin

Considering the main idea of the paper, namely that the interaction energy of reagents serves as a criterion used for their selection, as well as due to their insufficient study, the authors have therefore considered studying the aspects of computer modelling and molecular dynamics of largely used collectors for the flotation of nonferrous and precious metal ores. Three-dimensional molecular models for sulphydric reagents have been created, studying as well the distribution of the partial charges on their atoms. It has been shown that the value of the partial charge on the phosphorus atom in diethyldithiophosphinate and diethylmonothiophosphinate is high positive. The value of the partial charge of the sulphur atom is negative, strengthening its bond with the metal cations from the mineral surface. The molecular orbitals for the sulphydric reagents have been created determining as well the energy of their level. The computer modelling key parameters have therefore been defined. The new reagents have been tested for gold, copper and rhenium ore flotation. Gold recovery has increased with 4.2 - 4.7 %, copper recovery with 3.3 % and rhenium recovery with 15.5 %. A number of new flotation reagents have been recommended, such as: diethyldithiophosphate, (C2H5)2NCH2CH2OC(S)SNa, (C4H9NH)2P (S)SNa and also (C2H5)2P(S)ONa and (C2H5)2 P(O)S Na. Keywords: flotation, molecular modeling, design, orbital?s

Sep 1, 2012

By K. Anand Rao

Extensive exploration for uranium metal by the Department of Atomic Energy in India led to the discovery of new carbonate host rock uranium deposits Tummalapalle and Gogi, which are located in southern part of India. Alkaline leaching at elevated temperature and pressure using autoclave is the central unit process in the overall strategy for extraction of uranium from these new ore deposits. Autoclave leaching is affected largely by intrinsic nature of the ore and by the process variables and the equipment settings. In order to understand such a complex process and also to be able to predict the process performance under randomly (ore grade, uranium mineralogy, gangue mineralogy etc.) and consciously perturbed variable settings (partial pressure of oxygen, temperature, concentration of leachant, stirring speed and time), sound and robust mathematical models are needed with analytical and/or numerical solutions. Present investigation attempts to develop a variant of kinetic correlation based on shrinking core model for batch alkaline leaching process in an autoclave. The leaching model incorporates particle size distribution according to popular Gates-Gaudin-Schuhmann equation, rather than assuming a single mean size for all the particles participating in the leaching reaction. Kinetic experimental data generated in autoclave leaching of Gogi uranium ore was used to evaluate various constants of the model developed. The ore sample used for experiments assayed 0.21 per cent U3O8. The partial pressure of oxygen was varied between 0.15 to 6.5 atm, temperature from 343 K to 438 K, concentration of sodium carbonate leachant in the range 0.47 g mol/L to 0.94 g mol/L, and the stirring speed from 573 rev/min to 900 rev/min in the experiments. The goodness of fit of the leaching process model is found to be >0.95. Morphological studies carried out on leached and unleached particulate matter using Scanning Electron Microscopy with Energy Dispersive X ray analyses are included in the present study.

Sep 1, 2012

By Yuliy Rubinstein

"The paper presents a analysis of the history and the trends of development of flotation apparatus. The laws of their evolution are stated and the place and role of column flotation are indicated. It is demonstrate development and different design of column apparatus. The major parameters of column cell such as diameter and height are discussed. Options are proposed on optimization of hydrodynamic characteristics of columns with large-capacity cells. High efficiency of columns with cell height of 4-6 m is shown on examples of coal preparation. A new generation of multi sectional column cells has been developed. In the cells are zones with different aerohydrodynamic parameters: combined in the machine are co-and counter- counter flows of phases. The transition from single-chamber column to multi-sectional apparatus makes it possible to create favourable hydrodynamic and aeration regimes in each section of the column dependent on the pattern of material distribution by floatability. Efficiency of application different designs column apparatus uses shown on the example of enrichment of various non-ferrous metals ores and coal. The principles of mathematical simulation of the flotation process are developed. A scaling-up procedure for column cells was based on flotation macro- and micro- dynamics simulation.INTRODUCTIONColumn flotation is considered to be one of the most significant achievement in the field of mineral processing in the end of last century. We cannot but agree with this statement but would like to understand what underlies this success. History of the flotation column can not be considered in isolation from the development of flotation apparatus on the whole. It can be argued that the first attempt to switch from oil flotation to the use of bubbles during flotation was performed Bessel brothers in 1877 (Berlin patent 42 class 22, July 2) and in 1886 (Berlin patent 39,369 May 12). According to these patents, the crushed ore was mixed with oils , hydrocarbons and water. Then the pulp received in this way was heated up to boiling . Air bubbles and steam formed during boiling facilitate the flotation of ore particles coated with oil (first patent) or bubbles been generated by the reaction of lime with acid (second patent). The evolution in the design of the flotation apparatus incorporates the following key stages. Further development is connected with the Francis Elmore’s idea to use gas bubbles received at water electrolysis (UK, 13578; 1904). This method was not introduced then, but much later, in our time and on the essentially new technical basis it found a use for sewage treatment (electroflotation). Gas bubbling under vacuum patented also by Elmore (UK, 17816; 1904) obtained a practical use. It should be noted that the method did not lose its importance till now. The design of the camera has been surely optimized (Glembotskii etal, 1963). A year later A. Macquisten (UK, 26712) developed pressure (compression) flotation. Thus, the H.Sulman, H.Picard, D. Bell’s (US, 853120, May 29, 1905) basic patent and the adjoining T. Goover’s patent 1910 (US, 953746) formed the basis of the first and most important element of modern flotation: flotation with air bubbles sucked in from the environment. In 1914, J.Callow received a patent for on an apparatus where air was sparged through the porous false bottom of the cell ( US, 1104755). Woolen fabric folded four times was fixed on a perforated metal frame to be used for air sparging (Gaudin, 1932). The following year Durrel created the prototype of the injection (ejector) apparatus. The jet aerator made it possible to significantly reduce the size of the bubbles, in comparison with the filter cloth. An apparatus with slurry pre-aeration in an airlift prior to feeding into separation cell was developed Wagner in 1917 (US, 1235083). And finally, the first column apparatus with a counter-current of slurry and air was developed by M. Towne and S. Flynn in 1919(US, 1,295,817). ("

Jan 1, 2018

By R. S. C. Smart

Surface chemical factors, including the balance of hydrophobic (e.g. collectors) and hydrophilic (e.g. oxidation products, precipitates) species, are major control determinants in flotation rates of specific minerals and therefore grade and recovery. There are a number of challenges involved with the surface analysis of different mineral phases from process streams in a flotation facility. The first is to collect samples that are representative of the process and retain their surface chemistry prior to introduction into the instrument. The second challenge in studying the surface chemistry of specific minerals is to find reliable methods of mineral phase recognition. In surface analysis of mineral particles, confident mineral selection can be difficult with many multi-metal minerals and with precipitated, adsorbed, reacted and contaminant species in the outermost molecular layers. The third challenge is to provide a statistical surface analysis of multiple grains of the same mineral. Methods to achieve these aims are described. Principal component analysis (PCA) of ToF-SIMS data provides improvement in phase recognition, particle selection and associated variations in surface species. Specific examples from both lab and plant operations, demonstrate that this technique can be utilized to differentiate surface chemical factors promoting (hydrophobic species) or inhibiting (hydrophilic species) flotation. A study of copper ion transfer (inadvertent activation) from chalcopyrite to pyrite and sphalerite clearly identified a statistical difference in copper intensities between the sphalerite and pyrite phases corresponding to their flotation response. The PCA analysis applied to concentrate and tails samples collected from the Inco Matte Concentrator demonstrated extensive CuOH and NiOH transfer between chalcocite and heazlewoodite minerals. The statistical analysis has been able to identify mechanisms controlling recovery and selectivity. High intensity conditioning (HIC) tests in which sphalerite was separated from a complex sulfide ore gave a 5% increase in the overall Zn recovery. The PCA/ToF-SIMS statistical analysis revealed the discriminating depressant action of adherent aluminosilicate (gangue) fine particles and adsorbed ions on the surface of sphalerite grains. HIC conditioning resulted in the removal of these gangue fines improving surface collector attachment efficiency.

Jan 1, 2014

By P. Bevilacqua

In this paper the possibility to complete the copper recovery and to enrich in PVC a mixture of plastic granules obtained by grinding electrical cables are investigated. The recovery of a large part of the copper still present among the plastic granules was possible by means of a mechanical screening, the finer polymeric fraction was collected, at the same time. In order to complete the copper polymer separation the following techniques were employed. Counter current separation in water, static dense medium separation with zinc chloride solution and copper extraction with nitric acid and subsequent electrolytic deposition. A Tri-Flo® dynamic dense medium separator was employed in order to separate the lighter polymeric fraction, from the heavier polymeric fraction, mainly PVC. Water or a salt-water solution was employed to feed the separator device.

Jan 1, 2014

Deposit of Jinbaoshan platinum group metals (PGMs) ore ranks the second in Yunnan province, China. Study on process mineralogy shows that the grade of copper and nickel in the ore is just 0.16% and 0.20% respectively. Moreover, the impurities magnesium and iron and silicon are rich in the ore. The copper and nickel sulfides in the ore, especially the minerals of PGMs, are finely disseminated with the gangues like serpentine. Fine grinding is necessary, and high content of MgO in the concentrate is inevitable through traditional flotation technology on the basis of process mineralogy studies. Achievements on process mineralogy studies are applied to guide the flotation tests successfully. Progress on flotation has been made through comprehensive studies. Suitable grinding by two stages is required for the finely disseminated PGM sulphide ore to achieve the liberation of valuable minerals. Stage grinding and stage separation shall be conducted for a better recovery of valuable minerals. The oxidation state of mineral surface of sulphides has a profound effect on flotation of the ultra-fine sulphides, especially the pentlandite. The combined use of collectors enhances the selective collecting on the ultra-fine and low-grade valuable minerals, is of critical importance.

Jan 1, 2014

By M. M. Kulkarni1

Kaolin clay is used as a filler and pigment in various applications such as paper, paint, rubber, plastics, adhesives, ink and ceramics etc. Major mineral content in crude kaolin clay is kaolinite along with some accessory minerals as quartz, hematite, mica, feldspar, anatase, rutile, illemnite etc. The Fe and Ti bearing minerals play very important role in determining quality of the kaolin, as these minerals impart yellow, pink or darker color to the white kaolin. Conventional beneficiation methods used in kaolin processing are de-gritting, classification and sodium dithionite bleaching, which improves the optical properties of kaolin, wherein reduction of color imparting constituents such as Fe2O3 and TiO2 is marginal. In the present study, these coloring impurities are separated using selective adsorption of water-soluble polymers. Degritted kaolin samples after passing through 45 micron sieve is used in the study for selective flocculation by polyacrylamide based polymers. The effect of pH, zeta potential, and polymer dose on the reduction of impurities is studied. Analytical tools such as XRF, XRD, SEM, and TEM techniques are utilized and results are discussed in detail.

Sep 1, 2012

By G. G. Dong

This paper presents BF flotation machines in brief which are manufactured by Beijing General Research Institute of Mining & Metallurgy (BGRIMM). Dimensional analysis and similarity criteria have been used to scale up BF flotation machines. These scale-up criteria can be used to determine mechanical structure and hydrodynamic parameters including mixing, solids suspension, air transfer and power and so on. Similarity criteria are used to design 40m3 flotation machine being based on data from 1.2 m3 to 20 m3 flotation machines. Hydrodynamic tests of 40 m3 flotation machine in water are discussed.

Jan 1, 2014