Search Documents

By Tasuma Suzuki

Electrokinetic/permeable reactive barrier system is a promising in situ soil and ground water remediation technique to reduce toxic NO3- into less toxic NH4+. Using granular zero-valent iron (Fe0) as a reductant, the first objective of this study was to investigate the influence of the solid-liquid ratio and aqueouspHon NO3- reduction. The results obtained from a series of batch experiments showed that NO3- reduction was enhanced by either increasing solid-liquid ratio or decreasing aqueous pH. Based on insights obtained from batch experiments, the second objective of this study was set to design the remediation conditions of the electrokinetic/Fe0permeable reactive barrier system to maximize the NO3- reduction efficiency. Experimental results showed that the effectiveness of the system strongly depended on the Fe0 percentage in the reactive barrier, the pH in the anode reservoir, and the applied voltage, which were consistent with the results obtained from batch experiments. Under optimized treatment conditions, nearly 100 % NO3-was reduced into NH4+ in the permeable reactive barrier and collected in the cathode reservoir. Insights obtained from this study provided fundamental information on roles each of remediation design parameters plays, and will be useful to optimize the remediation conditions. Keywords: electrokinetic remediation, permeable reactive barrier, zero-valent iron, nitrate

Sep 1, 2012

By L. A. Vaisberg, E. V. Shishkin, S. V. Kazakov

"This research is targeted at finding solution to the problem of reduction of specific energy consumption during disintegration of solid materials with the help of machines, operating in a quasiresonant mode. The objective of the research is the development of an energy-saving method of disintegration of supestrong rock and by-products on the basis of vibrational units with two movable crushing elements, operating in a rigorous synchronous-antiphase mode without stringent kinematic links. In the course of investigations a mathematical analysis of the dynamics of vibrational units was performed to determine required mechanical parameters, allowing for adjustment of the machine actuating elements to high-frequency synchronous-antiphase oscillations in the quasiresonant frequency range. As a result of performed pilot tests, the reliability of desktop studies was confirmed and the dependency of process parameters on the machine regulated parameters in the quasiresonant frequency range was identified. The analysis of obtained data showed that during machine operation with cone-shaped crushing elements in the quasiresonant frequency range, the yield of the high-quality finished product (WFA grits of -3+1 mm grain size class) in one pass reaches 35%, whereas the form of the particles corresponds to the grain form with sharp edge. The quasiresonant operation mode of the vibrational unit with two freely suspended crushing elements (without stringent kinematic links) provided substantial reduction of energy intensity during crushing down to 0.16 kWh/t, which shows reduction of power consumption for crushing by more than 15% compared to conventional equipment.INTRODUCTION The most common and energy-consuming processes in the mining industry are the crushing and grinding of various solid materials. Such large energy costs are due to the fact that the capabilities of the existing crushing and grinding machines are based on traditional methods of destruction, and are limited by their kinematic features, which do not allow to reduce the energy intensity of processes, to lower the irreversible loss of useful components, to improve the quality of marketable products. In connection with the foregoing, the task of energy costs reducing for disintegration is one of the most important issues in the enrichment of both minerals and processing of man-made raw materials. The solution of this problem is possible only through the creation of a fundamentally new highly efficient technique and technology for processing raw materials [1, 2]. It seems that the greatest prospects in this respect are the vibration methods of disintegration, in particular, the vibratory cone crusher based on a two-mass system without rigid kinematic connections between the crushing bodies, with vertical vibrations of the working bodies. In this machine, the principle of rational material destruction is realized – crushing without re-grinding [3-5]."

Jan 1, 2018

By Paul W. Cleary

"DEM application in mineral processing has for many years been heavily focused on simulating mills of various types. This method can be used to simulate many other aspects of mineral processing operations and can be used both to enhance understanding of the underlying flows and of issues such a breakage, wear, blockage, product degradation, segregation and mixing. The application of DEM to four important classes of non-comminution problems and equipment commonly found in or near mineral processing plants are described. These are:- Particle transport (examples include a conveyor belt and an inclined screw conveyor)- Sampling (assessment of sample bias for cross-stream samplers)- Separation (the efficiency of vibrating screens)- Storage and reclaim (discharge from a multi-port hopper and segregation in a splitter bin with asymmetric ingoing and outgoing conveyor belts, apron feeders and impact plate)."

Jan 1, 2003

By Vladimir E. Vigdergauz

"Bubble-mineral complexes could be formatted by an attaching of hydrophobic particles to the surface of air bubbles or by an evolution of bubbles from solution onto hydrophobic surfaces. Measurements of contact angles, detachment forces (DF), induction times (IT), evolution pressures (EP) and flotation recoveries (FR) for the studying of minerals wettability at various pH and electrochemical potentials were used. An analysis of the obtained IT results show that a process of bubble attachment to a mineral surface is a rather slow one and it will scarcely be enough for bubble-mineral complex formation under the conditions of real flotation.The ranges of adhesion potentials obtained by DF measurements, Figure 1, correlate with the data of floatability-potential for pyrite. The ranges of adhesion potentials obtained by DF measurements for galena (-1 ÷0.2V) and chalcocite (-0.5÷1.2V) correlate with the potential ranges of floatability for galena (<0.2V) and chalcocite (>-0.4V). An increase of the DF and the cathodic limit of the adhesion potential with increasing length of the hydrocarbon chain were observed. EP-pH curves for sulfides are a mirror-like to the DF-pH curves, Figure 2. Structure of solid-liquid and liquid-gas borders has a determinative importance for formation of bubble-mineral complexes and subsequently flotation results. Under vacuum on the mineral surface there are produced micro bubbles and preferably they will be appeared on the hydrophobic sites. Water structure breaks near a hydrophobic surface facilitate water mass destruction and formation of gaseous phase embryos under decompression in the impeller zone. It simultaneously reduces a probability of produced micro bubbles dissolution as a result of pressure increasing owing to constant fluctuation of liquid densities into impeller zone. Comparison of Taggart’s evaluation of the suction behind blades of the impeller of an agitation-froth machine and ABEP data on galena, Figure, shows that gas evolution will be observed in the range of 1300-2700 revolutions of impeller per minute for hydrophobic and hydrophilic surfaces successively."

Jan 1, 2003

By Martin Rudolph

"Flotation is without a doubt one of the major processes for the separation of fine minerals and it has been applied for more than a century. A key task of a successful flotation separation is to find the proper chemical treatment to selectively hydrophobize and thus float a certain mineral phase using molecules or ions referred to as collectors, depressants, regulators and frothers. Commonly floatability is determined by microflotation tests using the Hallimond tube with pure mineral phases. This method however requires the pure mineral phase which is very often not even taken from the same deposit which is going to be processed. In this paper we present a new approach to in-situ determine and even map the floatability of finely disseminated mineral phases within cross-sections of an ore. It is based on measuring hydrophobic effects using colloidal probe atomic force microscopy with a hydrophobic polystyrene probe based on force spectroscopy with a lateral resolution of only a few nanometers. Coupled confocal Raman spectroscopy on the same locality enables the identification of the mineral phase. We present the working principles of the method and show which signals in the force spectra characteristic for hydrophobic interactions can be used to define floatability and which can then be mapped as single quantities, e.g. jump-into-contact events due to nanobubble occurrence or parameters of the long range interaction curves most probably due to capillary effects. A finely grained silicate ore containing the valuable rare earth mineral eudialyte from southern Sweden as well as pure samples of magnetite are presented as substrates to demonstrate the capability of this new approach. This method will not only help to find the proper flotation chemistry but it can furthermore help in researching and unravelling problems of floatability within similar mineral phases."

Jan 1, 2014

By Reuter M. A., R. D. van der Weijden, W. F. C. van Wageningen

"Copper(II) can be recovered or removed from acidic copper sulfate solutions as cuprite or metallic copper powder by reduction with carbohydrates. The copper powder characteristics, such as size and shape of particles, determine the tendency to adhere to reactor walls and to agglomerate. In order to make this process suitable for a commercial scale pipe reactor, process conditions and the reactor configuration were varied in order to influence the copper characteristics in a positive way. The aim was to achieve proper particle throughput in the pipe reactor and to obtain a well defined copper powder.In this paper the effect of both, chemical and physical parameters on the shape and size of particles were systematically studied in a number of autoclave experiments. These parameters include mixing, Cu(II) concentration, pH, temperature, seeding, use of additives and reactor materials. Additionally, Monte Carlo simulations of copper growth inside a Kenics static mixer were made. Results show that the use of additives and the use of static mixers influence particle characteristics the most."

Jan 1, 2003

By D. Chakraborty, Neeraj Kumar

"The study provides the comparative analysis of the performance of water only cyclones and hydrocyclone for iron ore fines processing at Joda Iron ore processing plant, Tata Steel. Joda iron ore deposits have higher proportion of kaolinite in the finer fractions and are meant to be separated with cyclones. The iron processing flowsheet of Joda comprises of water only cyclone for beneficiation of iron ore fines. Water only cyclones are used for the beneficiation of fines in the iron ore processing industry and have a larger cone angle compared to that of conventional hydrocyclones to enhance the density effect in the separation. They are aimed to achieve better product quality of underflow however; the desired result could not be achieved at the Joda processing plant. The water only cyclones were operating at the corrected cut-size of about 60 micron with an imperfection of 0.40 and water split to underflow was approximately 10%. The overall Fe recovery from the water only cyclones were 60%. Since the quality of fines produced from the water only cyclone couldn’t be improved, an attempt was made to process the fraction in the conventional hydrocyclone to achieve the desired product quality. The trial results indicated better product quality with the Fe recovery of 72% at corrected cut-size of 70 microns and imperfection of around 0.29. In view of above results it was recommended to replace the water only cyclones with hydrocyclones to achieve higher product quality of about 60% Fe content.INTRODUCTION Water only cyclones were installed at wet plant, Joda to process the classifier fines where the cyclone underflow is considered as concentrate and overflow is discarded as slime. Because of the lower capacity of the cyclones 30% of the classifier overflow was bypassed directly to thickener. Apart from this the quality of fines produced from the water only cyclone couldn’t be improved further hence an attempt was made to process the fraction in the conventional hydrocyclone to achieve the desired product quality and quantity. Hydrocyclone was installed at Joda after replacing stub-cyclone and came into operation on 23rd Aug’ 2017.The process variables of water only cyclones and hydrocyclones are tabulated below:"

Jan 1, 2018

By M. Nonaka

An attempt to produce fuel from biomass waste by hydrothermal treatment has been made with expectation to effectively utilize a renewable source of energy and an unexploited energy resource. In this paper, we have used empty fruit bunch (EFB) that is a residue after recovery of crude palm oil from palm oil trees in a plantation in a tropic country. A hydrothermal treatment was conducted using a 500 mL autoclave, with alkali (K2CO3) catalyst. EFB was decomposed more by alkali catalyst of lower alkali content and rather polymerized in higher catalytic region. The functional group composition of the solid phase oil is similar independent of alkali content, however its burning characteristic became more incombustible with increasing alkali content.

Jan 1, 2014

By T. Suzuki

Acid leach liquors from spent lithium-ion batteries employing lithium cobalt dioxide (LiCoO2) as a cathode active material contain valuable metals such as cobalt and lithium, as well as common metals such as aluminum and copper. The objective of this study was to develop a hydrometallurgical process providing a high selectively between aluminum, cobalt, copper, and lithium from hydrochloric acid solutions. Batch experiment results showed that selective hydroxide precipitation approach was not suitable because a significant amount of cobalt and lithium was co-precipitated with aluminum and copper hydroxides. In contrast, batch experiments and the subsequent data analysis indicated that the sequence of solvent extraction circuits using PC-88A, Acorga M5640, and tri-n-octylamine (TOA) extractants effectively separates four metals of interest. In the first circuit of the proposed process, copper was selectively extracted by Acorga M5640 at the pH 1.0-2.0. Aluminum, cobalt, and lithium remain in the aqueous phase. In the second circuit, aluminium is selectively extracted by PC-88A at pH 2.0-2.5. For the separation of remaining cobalt and lithium, Acorga M5640 provided higher separation efficiency compared to PC-88A single extractant and PC-88A/TOA mixed extractant. However, the stripping efficiency of cobalt from the Acorga M5640 organic phase was found to be low (less than 10 %). Therefore, PC-88A/TOA mixed extractant rather than Acorga M5640 is an advisable choice for the separation of cobalt and lithium. Keywords: spent lithium-ion secondary batteries, solvent extraction, lithium, cobalt

Sep 1, 2012

By Y. Nahmad- Molinari

We present a novel on line inductive sensor for the determination of the quality of the concentrates of iron ores. This device is coupled with a cheap USB Data Acquisition System that makes it versatile enough to simultaneously control up to seven fluxes at a very low cost (< $300 US dollars), and achieves a resolution better than 0.5 % on the determination of the magnetic iron content in the concentrate. A RLC circuit with its inductive element placed surrounding a sample of pure magnetite concentrate is tuned at its resonance frequency, by means of adjusting, the feeding voltage of a voltage-controlled oscillator (VCO) and several samples with mixtures of different contents of silica and magnetite are placed in order to get a calibration curve. After some signal conditioning, a National Instruments USB-DAQ NI-6008, acquires the amplitude of the signal via USB port on a PC using a Lab-View program designed for such purpose, in which the calibration curve is used for on-screen data presentation directly in percent of magnetite content. The implementation of this device for control purposes on line directly placed on the concentrators would allow better efficiency of the process and higher quality of the final concentrate by con-trolling; the rotation speed, the rising or dilution water fluxes or bypasses towards milling recirculation cycles.

Jan 1, 2014

By A. T. Sutaone

"In the Dongri Buzurg Manganese Mine of M/s Manganese Ore (India) Ltd., high grade lumpy manganese ore required for iron and steel industries is produced through multi-stage crushing and screening. This has resulted in accumulation of 50,000 tonnes of low grade fines over the years. This production of such fines is still going on. The fines create environmental problems, like air and water pollution and siltation in adjoining fields. Besides containing lot of manganese values, they occupy large space which is very scare in mining area.The Indian Bureau of Mines under one of its statutory functions has suggested the company to explore the possibility of recovery of additional values under conservation and environmental aspects. Hence the company has sponsored a bulk sample for beneficiation studies in the Modern Mineral Processing Laboratory and Pilot Plant of Indian Bureau of Mines at Nagpur, India. The main manganese minerals present in these mine rejects have been identified as pyrolusite and psilomelane. The purpose of this study was to explore the possibility of evolving a suitable beneficiation flowsheet to obtain manganese concentrates assaying over 72% MnO2 to be used as raw material for the manufacture of dry cell batteries.The sample/material was subjected to characterisation studies in terms of chemical analysis, granulometry and mineralogical compositions. Based on these characterisation studies, the beneficiation process developed comprised of desliming, jigging and low intensity magnetic separation mainly to reject quartz, silicates and jacobsite. The manganese concentrate thus produced assayed 70.2% MnO2 with MnO2 recovery of 78% and weight per cent yield of 63.5. This natural concentrate could be mixed with the electrolytic manganese dioxide produced by the company and this blend can thus be used as a raw material for the manufacture of dry cell batteries by the end users. The paper deals with the details of test work carried out in evolving the process flowsheet."

Jan 1, 2003

By Tim Suljada, Mary Stewart, Jim G. Petrie, Damien Giurco

"The minerals industry is being challenged to reduce the amount of virgin ore that is mined, and to replace this material through the recycling of used commodity items and scrap, or by the reprocessing of waste materials. It is argued here that the existing technology base of minerals processing and refining offers real potential for handling these secondary resources. The challenge is to develop tools by which the most preferable recycling routes (both economically and environmentally) can be identified from a list of feasible alternatives, taking into account any operational constraints of these technologies.This paper describes an heuristic approach to developing the family of all technically feasible flowsheets to address this challenge, from which a preferred option may be selected according to a set of decision criteria (economic and environmental). Our approach uses conventional flowsheeting techniques of selecting flow variables and splitter functions, supported by design performance information for each unit operation. This set of design decision variables is augmented by knowledge of the suitability of a particular waste or scrap stream for a given unit operation within a flowsheet. We achieve this by comparing the composition of the scrap stream with the range of mineral streams for which the unit operation was designed initially. This is inspired by the “overlap” approach proposed by Legarth, where an “overlap” of 1 would suggest that there is high degree of compatibility between a given secondary resource stream and a primary mineral stream as inputs to a specific technology. The “overlap” concept has been extended to include information about the physical characteristics of secondary resource streams, as well as information relating to synergistic / antagonistic influences of minor elements present in the waste stream. A flowsheet which delivers a product of acceptable quality from a given secondary resource material is built up from a progression of unit technologies. The exercise is repeated to generate the family of all feasible flowsheets from combinations of acceptable unit technologies."

Jan 1, 2003

By Pawel Strzalkowski, Marta Baszczynska, Urszula Kazmierczak

The paper presents issues related to interference of mining activities with the environment. Exploitation of mineral resources causes primarily a modification of the landscape. All of the negative impacts on environment are short-lived and last as much as it takes to exploit the raw material. After the mine closure reclamation is necessary during which all aspects that reduce harmful effects of the mining activities on the environment must be taken into account. Current ways of reclamation allow recreating natural environment, which is different from the original and enriched in diverse new values. This requires propositions of new forms of converted land development through a detailed analysis of technical, natural, planning, economic and social sphere requirements. Before making final decisions regarding selection of direction of reclamation, a thorough analysis of the key factors has to be carried out. All steps related to the implementation of the reclamation project are shown in the paper using Limestone Mine "Górazdze" located in the south-western part of Poland as an example. This paper also presents an analysis of current ways of post-mining reclamation towards agricultural and forestry landscape, along with our own suggestion for their extension in order to preserve biodiversity. For choosing optimal solutions the most relevant criteria were considered: existing natural values and possibility of their protection. Taking into account the economic and social aspects, supported by natural potentials, implementation of tourism and recreation in this area were proposed. It was shown that this proposition would not interfere with the current trends of the natural landscaping. Finally, after completion of reclamation and land development in the considered mine area, creation of a geo-park was proposed along with appearance of geotourism in the area. To illustrate the proposed forms of post-mining land development in the form of maps, an ArcGIS(ESRI) software was used.

Jan 1, 2014

By Robinson Irarrazabal, Edison Collinao, Rodrigo de Carvalho, Patricio Davila, Marcelo Tavares

"In recent years, DEM (discrete element method) softwares, along with 3D laser measuring equipment, have become powerful tools to describe mill charge behavior, as well as forces acting on the liners of SAG mills. With the aim of contributing to streamline this application of the advanced technologies ME Elecmetal and Universidade Federal do Rio de Janeiro, UFRJ, proposed a new approach to improve the design of mill liners using elements from mechanistic modeling of grinding. The paper presents a methodology for continuous improvement of liner design, which uses information from the DEM collision energy spectra in the mill discriminated for the different components (ore and steel balls), as well as information on the breakage properties of the ore being ground. From these it proposes the concept of "effective collisions", which corresponds to the collisions that are of sufficient magnitude to cause breakage, thus allowing to discriminate from impacts that do not cause breakage either in a first impact or after repeated loading. It also tracks the collision of steel balls against the shell in order to assess their potential damage to the liners. An industrial case study is presented of a 38’ diameter SAG mill, which was experiencing challenges associated to liner breakage and low efficiency with the old liner design. Through a modification of the liner design, simulations demonstrated the potential benefit associated to reduction in ultraprojection and improvement in mill capacity. Implementation of the new design in the SAG mill was carried out, resulting in increase in daily throughput from 6 to 12%. Further, the time spent in liner change was reduced by 47% given the reduction in the numbers of parts. This operation also benefited from having no stops due to unplanned shutdowns to replace broken tiles. These demonstrate the benefit of coupling advanced computational tools to sound engineering principles in continuous improvement of liners."

Jan 1, 2014

By I. Blayda

The purpose of this work is to study and make comparative analysis of germanium extraction and related valuable components of the sublimates from the burning of domestic power coals (product 1) and germanium sulfide materials, which are a waste of lead-zinc production (product 2), by traditional chemical methods (distillation of germanium in the form of tetrachloride from raw and preliminary burning source) and by microbial bioleaching of sulfur-oxidizing bacteria. The dependence of the germanium extraction by chemical methods from phase composition of the initial raw materials was installed. The germanium tetrachloride extraction from products 1 and 2 were 78.50 and 19.52%, respectively. Such difference in indexes on extraction, is caused by germanium confinement as concomitant trace component to the basic phases to carriers. The share of acid-non-soluble compounds (tetragonal modification GeO2 and silikogermanaties) in the product 1 account for 21.5 % of germanium. Ratio between acid-soluble and acid-not -soluble germanium forms are 19.52 and 80.48 %, respectively, in the product 2. Our experiments have shown, that implementation of restorative firing (with addition of 30-40 % carbon at 1150 0?) of sulfide product 2 considerably impacted on the extraction of germanium tetrachloride (91.76 %) in comparison with its low enough extraction at straight distillation of hydrochloric acid (19.52 %). The results are confirmed by a set of physical methods. The results of processing the same so-called hard phase?s material (product 2) with the help of microorganisms are presented. It Has been established, that selected strains of bacteria are capable of extracting from initial raw materials not only macro components (iron, zinc, lead, manganese, aluminum, nickel), but also micro impurity of rare metals (gallium, germanium, zirconium). It is important that these metals were not extracted by traditional chemical methods (with application of aggressive conditions and heats) independently of the phase composition of the source. Almost complete extractions of germanium in solution using sulfur-oxidizing bacteria take place in the first day of the process independently of the phase composition of the source and the type strain. The results have practical significance and can be the basis for developing a unified biotechnological method of technogenic waste processing with a purpose of their sterilization and detoxification with simultaneous obtaining concentrates of valuable metals. Keywords: germanium, extraction, sublimates, bioleaching, sulfur-oxidizing bacteria.

Sep 1, 2012

By Buks Kruger

"After the milling and flotation of the platinum bearing ore, the flotation concentrate is electrically smelted in 6-in-line electric arc furnaces and the resulting furnace matte treated in Peirce Smith converters to remove the iron sulphide. The iron free (less than 1% Fe) converter matte is then granulated and sent to the Base Metals- and Precious Metals Refineries for further processing.During the smelting and converting processes two distinct gas streams are produced.The Peirce Smith converter off gas contains 4% - 9% SO2 which is treated in a conventional Sulphuric Acid Plant to produce sulphuric acid (H2SO4).The electric furnace off gas contains 0.9% SO2 and was (until September 2002) vented through a 91 meter high stack to atmosphere.Off gasses which contain less than 3% SO2 is difficult to handle and quite a few processes had been developed over the years to cope with this gas. A broad spectrum of process suppliers and technology approaches is available and the different technologies can be divided into a few main approaches i.e.Scrubbing of the off gas with an alkaline solution to produce an environmentally friendly and stable waste product which can be discharged onto a tailings dam or permanent landfill site.Physical absorption of the SO2 into a chemical solution to produce high quality chemically pure process chemicals.Catalytic reaction of SO2 with O2 to produce SO3 which is absorbed in water to produce sulphuric acid of less than 90% strength.In October 2002 Impala Platinum commissioned a Sulfacid Plant at its Smelter in Rustenburg which recovers the SO2 from the electric furnace off gasses into a weak sulphuric acid solution.The Sulfacid Plant technology is widely used in the paint pigment industry. This is, however, the first application of the technology on electric furnace off gas.The furnace off gasses contains flue dust which is removed in electrostatic precipitators. The gas exiting the precipitators normally still contains between 40 mg/Nm3 and 60 mg/Nm3 dust and passes through a quench-scrubber before entering the reactors. The quench-scrubber cools the electric furnace offgas down from ± 200 °C to 60 °C and act as a final dust removal stage."

Jan 1, 2003

By Arkady Senchenko, Sergey Rybkin, Svetlana Lagutina, Alexander Aksenov

"The application of autoclave leaching technology for sulfide concentrates containing base and precious metals is spreading nowadays. In the process of concentrate leaching silver accumulates in the forms of jarosite compounds, transforms into passive chemical state and is mostly found in solid phase. Effective technology development for silver recovery from solid phase of concentrate autoclave leaching raises the necessity for comprehensive research of silver forms of occurrence and their properties in this product. The possible form of silver presence in solid phase of concentrate from autoclave leaching is argentojarosite. This article is about the study of physical and chemical properties and structure of synthetic argentojarosite - AgFe3(SO4)2(OH)6. A method of argentojarosite synthesis has been developed under conditions simulating the process of autoclave leaching of sulfide concentrate, and includes silver dissolution in the form of Ag2SO4, Fe3+ sulfate hydrolysis, AgFe3(SO4)2(OH)6 build-up. X-ray data of synthesized argentojarosite completely correspond to those of natural mineral. The structural formula of this complex compound has been studied and confirmed. The chemical properties of synthetic argentojarosite, its solubility in acids and alkalis have been investigated. Phase changes when heating argentojarosite with the build-up of iron oxide and silver sulfate stop at the temperature equal to 650 ºC. Based on the results received the technological solutions for solid phase of autoclave leaching of concentrate have been developed with silver recovery of 95-98%."

Jan 1, 2014

By Naoki Hiroyoshi, Hajime Miki, Tsuyoshi Hirajima, Masami Tsunekawa

Acidic solutions for chalcopyrite leaching contain cupric, ferrous and ferric ions, and the oxidizing power of the solutions is indicated by a redox potential, determined by the concentration ratio of ferric to ferrous ions. This paper reviews our previous studies on the redox potential dependence of chalcopyrite leaching in sulfuric acid solutions. Leaching and anodic-polarization experiments showed that coexistence of cupric and ferrous ions activate anodic dissolution of chalcopyrite, causing faster copper extraction at the potentials below a certain value (critical potential). The analysis of the AC impedance spectra for chalcopyrite electrode indicated that a high-resistance passive layer grows on the chalcopyrite surface without cupric and/or ferrous ions, and that coexistence of these ions causes a formation of another product layer and inhibits the passive layer growth at low potentials. These results are explained by a reaction model assuming the formation of intermediate Cu2S due to chalcopyrite reduction and the subsequent oxidation of the Cu2S. The critical potential corresponds to the redox potential of the Cu2S formation and the predicted values matched with the experimental results. Catalytic effect of silver ions on chalcopyrite leaching was also discussed based on experimental results and the above model.

Jan 1, 2003

By Markus A. Reuter, Jacques J. Eksteen

"The modelling of bath type furnaces tends to be either fundamental in nature or total empirical ""black box models"". While models of the first kind are robust, they tend to lack accuracy, in cases where they are to be used for process control, and may take an overly long in development time. On the other hand, black box models tend to lack robustness of prediction for all circumstances and tend to be limited to interpolate based on historical data. While this may very often provide short-term accuracy, the models may have problems with stability in the long term. Moreover, the model structure may not reflect any of the fundamental properties of the system and remains opaque to fundamental analysis. The aim of the model development is in obtaining a model that have robustness, high accuracy, a short development time and which is adaptive to a changing environment. The models are specifically developed for on-line decision support or control of furnaces. The modelling approach is evaluated for a chromite bath smelting furnace. The role of systems analysis, mass balance smoothing, thermodynamic analysis are integrated into one generic algorithm for bath type furnaces. Not only are fundamental process relationships such the mass and energy balances satisfied through a scientific method of data reconciliation; the proposed modelling approach allows adaptive prediction, the first step towards predictive control or metallurgical decision support.It is shown that neither an ARMAX model only, nor a purely equilibrium model only, could predict the dynamics of the process very well. However, a combination of the two approaches more than doubled the accuracy as measured by the R2. It was noted for carbon dissolved in the alloy, that the improvement in R2 in using a hybrid modelling approach was more than the sum of the R2 of the individual traditional approaches. Similar improvements in modelling performance were noted for all other species.It shows further that process dynamics may totally overshadow the effect of thermochemical equilibrium (even when the thermochemical equilibrium prediction includes the recycled alloy and slag heels as additional feeds). The exclusion of process dynamics therefore leads to erroneous results."

Jan 1, 2003

By Sanggono Adisasmito

"The quality of the higher education in Indonesia is being improved by implementing a program financed by the World Bank under a project named QUE (Quality for Undergraduate Education). The investments are provided to selected study programs through a competitive selection process. The grant finances staff development, the purchase of equipments, textbooks, consumables, technical assistance, and incentives for outstanding faculties such as teaching grants, project grants, lecture note awards, and educational policy studies. These additional investments are provided to produce chemical engineering graduates that will compete beyond the national market.Chemical Engineering Department of Institut Teknologi Bandung in Indonesia has been selected to receive the QUE grant beginning the year 2000 and ending the year 2004. The department is actively involved in the mineral processing issues, particularly in the aspects of energy supply and the environmental protection. The activities are distributed in different laboratories and areas of expertise, such as: thermodynamics and utility systems, process equipment, chemical reaction and catalysis, microbiology and bioprocess engineering, process control, ceramics, as well as polymer and membrane technology. The main objectives of the QUE project are to improve the undergraduate program in the following aspects: Relevance, Academic atmosphere, Institutional management and commitment, Sustainability, as well as Efficiency and productivity, or abbreviated as RAISE. At the end of every fiscal year, the progress of the program is evaluated to measure the effectiveness of the project.The achievement of the QUE project objectives were assessed using performance indicators developed during the program design. There are six indicators to measure the performance of the individual program of study, such as: (1) Admission Test score, (2) average students' Grade Point Average (GPA), (3) average graduates' length of study, (4) graduates' waiting time before getting first job, (5) Test of English as Foreign Language (TOEFL) score, (6) Graduate Record Examination (GRE) score. Essentially, the RAISE evaluation criteria will be used to perform three main functions, such as (1) to measure the achievement through the six quantitative performance indicators, (2) to support the progress of evaluation and reporting throughout the implementation of the program, (3) to provide a universal framework for qualitative evaluation."

Jan 1, 2003