Search Documents

By Shaw-Shong Liew

This paper presents the design concept using floating piles to support 2500Ton oil storage tanks on a very soft alluvial clayey soil of about 40m thick in Riau Province of Sumatra, Indonesia. The floating piles of various penetration lengths were designed to support seven numbers of such storage tanks seating on a 20m diameter and 500mm thick reinforced concrete (RC) circular raft. The pile points have been strategically located at the RC raft. Varying pile penetration lengths have been designed to minimize the angular distortion of the thin RC raft and the out-of-plane deflection at the tank edge. Vibrating wire strain gauges were installed at different levels inside the ø350mm prestressed reinforced concrete piles to measure the load transfer profile during the static load tests and water-loading test. The installation and interpretation of the instrumentation are described and discussed. Boreholes, in-situ tests like piezocones, vane shear tests and standard penetration tests, and laboratory testing were carried out to obtain geotechnical parameters for the pile designs. Static load tests were also carried out on the spun piles of varying lengths of 24m, 30m and 36m respectively. It has been demonstrated that the floating pile system can be a cost effective design to support heavy structures on very soft compressible deposits with satisfactory performance. Finally, the design concept validated with the results of instrumentation is discussed.

Jan 1, 2002

By David B. Paul

"ABSTRACTThe US Army Corps of Engineers (USACE) has 704 dams in their inventory and over 100,000 miles of levees with a capital value of over $150 billion. Currently, there are 319 dams that are classified as high hazard and have actionable failure modes that will require structural modifications. The most frequent actionable failure mode associated with the inventory is seepage and piping. One of the most effective engineering solutions is the installation of a cutoff to limit seepage. Currently, USACE has over $1.5 Billion of cutoff wall projects under construction and/or design. Given the magnitude of the dam and levee safety issues, USACE is developing a new Engineering Manual (EM) titled “Seepage Control Cutoffs for Dams and Levees.” This EM covers all of the methods to construct cutoff walls. USACE has partnered with the Deep Foundation Institute (DFI) in preparation of the EM to ensure that it is comprehensive and draws from the expertise of the specialty foundation engineering companies that design, manufacture, and construct seepage control cutoffs around the world. The EM contains case histories as well as a comprehensive project statistical summary and guide specification paragraphs. The goal of USACE was to make the EM a state of the art document for use by Districts.HISTORYSlurry wall construction techniques were developed in the late 1940’s in Italy by ICOS. The first use of the slurry trench method of construction in the United States was by the USACE Memphis District in September 1945, to form a partial cutoff along the Mississippi River levee on the Arkansas side of the river just below Memphis, Tennessee. The idea for the project probably evolved from the use at that time of puddle clay trench cutoffs combined with the use of drilling mud for advancing borings. A paddle wheel mixing device was constructed for making slurry from native clays. Trenches were dug to a 20-ft depth using a trenching machine and to a 35-ft depth using a dragline with a 100-ft boom and 2-cu-yd bucket. Backfill was mixed in windrows at the site from hauled-in clay gravel and native materials and pushed into the trench by a bulldozer when the length of the trench was equal to about twice the trench depth. It is amazing that after almost 70 years, the technique is still about the same as it was when first developed by the Memphis District. A soilbentonite cutoff was constructed under the Kennewick Levee adjacent to the Columbia River as part of the McNary Dam Project in Washington by the Walla Walla District in 1952 The first application of a soil-bentonite slurry trench cutoff for control of underseepage at a major earth dam was at Wanapum Dam on the Columbia River in Washington in 1959.The first cement- bentonite cutoff in the United States was constructed at the Tilden Tailings Project to store tailings from the Tilden Mine in Michigan in 1976. The first cement-bentonite cutoff constructed at a dam on a river retaining a reservoir in the United States was completed in 1978 at the Elgo Dam (formerly the San Carlos Dam) in Arizona.The USACE has designed and constructed some of the deepest and most complex cutoff walls for dams since the 1970’s. The first major concrete panel cutoff wall constructed in a dam in the United States was at Wolf Creek Dam (Nashville District) by the ICOS Corporation between 1974-77. The dam has a long history of seepage issues associated with the karst geology that comprises the foundation. In 1968, about 17 years after first being impounded, wet areas, muddy flows in the tailrace and sinkholes in the downstream toe adjacent to the switchyard occurred."

Jan 1, 2014

By Li Keqiang

This paper discusses the pile foundation of tall buildings in Shenzhen region. For 156 constructed tall buildings exceeding 18 storeys, about 86. 5 per cent of the sum. The two main types of foundation used are the semi?machine?bored/slurry drilled cast?in?situ pile and the excavation pile (hand ?dug caisson). The engineering geologiical condition in Shenzhen was analysed. In general, the bed rock level is not too deep. It belongs to hard rock, but the geologic structure is more complex and the tectonic fissures is plenty. According to experiences of the researches, tests, designs and constructions of pile foundation, we present the basic design principle of pile foundations for tall buildings as follows; (1) pile strength control to select the pile type and to choice the cross sectional dimen­sions, must be in compliance with the strength of the pile. (2) bearing stratum strongly weathered, moderartely weathered and slightly weathered rock may be used as the bearing stratum. (3) bearing pile bored /drilled cast-in-situ pile designed as an end bearing pile. (4) friction pile precast concrete pile, prestressed concrete tubular pile and driven cast-in-situ pile designe as a friction pile. In case, pile design is in compliance with these principles, it may be safe, economical and reasonable.

Jan 1, 1991

By Emöke Imre

A point-symmetrical linear coupled consolidation model with displacement boundary condition is suggested for the description of the consolidation around the pile tip after pile penetration. Analytical solution is given. Main features of the solutions are predicted by the analysis of the system of differential equations and, the boundary conditions.

Jan 1, 2002

By Gary Kuhns

Central Florida is among the fastest growing urban areas in the United States, and its rapid development has required the steady construction of various types of civil engineering works. The karst geologic terrain and variable geotechnical conditions, however, present special challenges to the design and construction of deep foundations. The subsurface profile can be idealized as a surficial layer of Pleistocene sands, underlain by the highly variable Miocene-age Hawthorn Group, consisting of various combinations of sand, silt, clay, phosphate and highly weathered limestone. The Hawthorn Group is underlain by Eocene-age limestone that comprises the Floridan aquifer. Vast networks of solution cavities are present throughout the Eocene limestone, sometimes allowing downward raveling of the overlying soils and the creation of sinkholes. In some cases, the relic sinkholes can be filled with soft compressible organic soils extending to depths greater than 100 feet (30.5 m). Driven piles are frequently employed as a deep foundation alternative, although occasionally cast-in-place piles/shafts have also been used. Piles are often driven for bearing in the weathered limestone within the Hawthorn Group, but are sometimes installed as friction piles in the upper soil and intermediate geomaterials. Dynamic pile testing is routinely performed during pre-construction test pile programs, or during production for quality control and assurance purposes. This paper presents discussions on the design and construction aspects of deep foundations unique to Central Florida subsurface conditions and local practice. Foundation issues such as subsurface variability, soil setup, pile damage, negative skin friction, and sinkhole conditions are discussed with the aid of demonstrative case histories.

Jan 1, 2003

By W. Sondermann

"AbstractWith the increasing demand in reuse of inner city areas and the urgent need for deeper foundation pits under cramped circumstances, adjacent structures close to and high ground water level, the well-known established technologies especially with small to mid-sized dimensions are often too time consuming and occasionally not economic to install lateral support systems. The alternatives for these specific cases could be the usage of the deep mixing technology to create lateral support systems in reinforcing the deep mixing elements additionally to transfer the horizontal loads from earth – and water-pressure.With increasing demand in depth and water tightness, verticality and overlapping of single column solutions are becoming the key in execution. In addition, for some applications subsoil-conditions were not ideal for wet deep mixing technologies. The tubular soil mixing system (TSM) as a combination of mechanical mixing and support of hydraulic cutting by jet grouting can provide solutions toovercome these challenges.1. Current market conditions and trendsThe present financial crisis and the efforts not only to consolidate national budgets, but also to rescue certain banks, have not left the building industry unaffected either. Some drastic cutbacks to public budgets, along with the increasingly restrictive granting of credit for the financing of construction projects, have led to enormous over-capacities in the building sector, with purely negative impact. As a consequence of these negative developments, many companies are experiencing the pressure to restructure more quickly and to reduce costs but at the same time to keep the consequences of all activities, both externally and internally, within limits acceptable to employees, owners and finance institutions and last but not least consumers."

Jan 1, 2014

By Karl A. H iggins, James P. Racine

"Displacement Cast-in-Place (DCIP) piles are not a common deep foundation type in the Washington, DC Metro Area market. As a result, less regional data is available for these foundations compared to other alternate deep foundation types. Displacement cast-in-place piles (DCIP) differ from traditional Auger Cast-In-Place (ACIP) piles in that the pile annulus is formed by pushing a partially-flighted, auger bit to depth via a large mandrel. The auger bit includes a displacing body near the bottom of the tooling. Therefore, little to no spoils are generated during installation and the soil around the annulus is largely densified in-place due to the displacing body being slightly larger than the mandrel it is attached to.Due to this densification, one would expect that the theoretical DCIP capacities (compression or tension) would be greater than an ACIP pile (assuming a pile of similar length and diameter). After 20 static load tests and the installation of over 6,000+ piles on the MGM National Harbor Casino Project, the differences in pile support characteristics between DCIP and ACIP piles of same size and depth was small. The performance of both pile types depended on the density and type of soil within the bearing stratum. In some early cases of DCIP use, the performance exceeded expectations and appeared to be more in line (or better) than typical capacities obtained from driven displacement piles. Other times, the tip elevations could not be achieved or were so difficult to achieve that installation delays occurred and/or significant additional engineering effort was required to address piles short of their requirement embedment.This paper will discuss the limitations of DCIP pile installation in dense Coastal Plain soils and will present the lessons learned during this project. The paper will also compare the DCIP pile type to both conventional ACIP and driven displacement piles utilizing regional and site-specific load test and installation data."

Jan 1, 2017

By Ali Ameli

Design loads are limited for piles relying upon toe stresses in rock due to uncertainty about the rock quality over the whole pile diameter because of rock mass properties or construction effects. The paper discusses the use of video images to evaluate rock quality at the bottom of piles socketed into graniodorite bedrock in a steel pipe pile project. Skillful interpretation was required to assess the 3D properties of the rock from video images. It is necessary to observe the rock mass characteristics near the project site for better perception of the rock features from the images. Video image interpretation skills were established by the evaluation of the cores drilled under the socket base and the results of pile loading tests. Correlations were found between rock appearance in the images and the rock socket drilling records. Rock socket acceptance criteria were developed through monitoring the drilling operations for the specific site procedures. Video images then served as one of the quality-assurance tools together with probing and pile loading test. Lessons and methods learned from video inspection in this project could be used to evaluate rock quality in similar cases.

Jan 1, 2006

By John P. Davis

The use of conventional, circulatory air rotary and fluid rotary, cased and uncased drilling methods in the vicinity of sensitive infrastructure can have deleterious effects on the ground conditions surrounding and supporting structures and the structure itself. Furthermore, the use of these conventional methods offers the engineer or contractor little information about the condition of the subsurface during geotechnical applications. Conversely, sonic drilling measurements and samples can be used to evaluate actual conditions during the progress of exploration and construction across a given site. This paper will discuss the history and properties of sonic drilling and explore case histories of geotechnical applications for the advancement of boreholes within vulnerable structures and on sensitive sites for several recent infrastructure projects ? a tunnel and railroad project, a dam grout curtain project, a bridge micropile exploration project and a tunnel instrumentation project. Project summaries will discuss the advantages realized when the application of sonic drilling techniques demonstrated superior accuracy, quality control, efficiency, productivity, penetrability, waste minimization and adaptability when drilling adjacent to or within existing infrastructure. Finally, the discussion will address the current testing and application of sonic drilling to the installation of micropiles, earth retention anchors, grout injection and instrumentation installation where the quality control benefits provided by the inherent soil cores, measurement while drilling systems, accuracy and non-destructive production drilling features will be advantageous.

Jan 1, 2006

By Martin J. Kenwright

Within the famous Harrods department store, a new lift shaft has been constructed, servicing a depth of 22m below ground level as well as the existing 6 storeys of the store. The shaft will connect with a new goods tunnel which is to be excavated beneath the shop, as well as new floor space above ground level which has resulted from the infilling of a previously existing lightwell within the store. The construction of the deep shaft while maintaining uninterrupted use of the store by the Client led to a number of innovative solutions being undertaken. Empirical assessments were made of settlements anticipated from the construction process, which took place within a congested environment of existing foundations. Various elements were designed and installed to mitigate the effects of the inevitable ground movement on the surrounding overlying structure, which supported sensitive high quality finishes and mechanical and electrical installations. The reinforced concrete lining of the shaft was contained within a cofferdam of minipiles. The minipile placement accuracy (1 in 150) was vital as it could not interfere with the subsequent tunnelling works. As the scheme progressed this became even more critical since the minipiles were needed as support for parts of the permanent works. This paper describes:- the high quality placement and control of the minipiled cofferdam, the methods employed in assessing ground movements and the techniques used to mitigate against the effects of these movements.

Jan 1, 2000

By Michael W. Oakland

Deer Island is the site of the Massachusetts Water Resources Authority (MWRA) wastewater treatment plant which, when completed in 1999, will serve 43 cities and towns in central eastern Massachusetts. Deer Island is located in the Boston Harbor, as shown on Figure 1. The existing wastewater treatment plant on Deer Island is being upgraded to include secondary treatment to comply with Federal require­ments. The new treatment facilities will process an average of 455 million gallons of sewage per day; total capacity will be about one billion gallons per day. The new treatment facilities will cover virtually the entire island. [ ]

Jan 1, 1994

By R. Stenne

This paper deals with a complementary soil investigation which being part of the contract helped understand the behavior of a softened clay and adjusted the design of a retaining structure accordingly. The investigated softened clay proved to have lost its original strength but had maintained some characteristics of its stress history and in particular high horizontal stress. Pressuremeter tests and flat dilatometer tests were of interest to estimate the at rest earth pressure. A design consisting of a T-shaped slurry wall in conjunction with transverse walls was the most effective solution to cope with high active pressures and low passive pressures.

Jan 1, 2000

By Y. X. Tong

The simplicity off Ø=0 analysis has been taken advantage of to evaluate the geotech­nical problems of open caissons, slurry trench walls and piles in Shanghai. Undrained shear strengths obtained by various testing methods are correlated with case record and experimental data. Some problems posed by the construction of tall buildings are briefly discussed. Comments on applications are made to help engineers deal with practical problems.

Jan 1, 2010

By B. Broms

The "Bawang Pile" (in english "onion" pile) described in the article consists of a cased concrete shaft and an expanded base. The steel casing is first driven by an internal drop hammer and then the base is formed in-situ by the raming the concrete at the bottom of the slitted casing. This new type of pile can be used for underpining (small head room) of buildings and as foundation for transmission towers or lamp posts. Full-scale load tests in compression and in tension on the Bawang pile and on steel pipe piles demonstrate the dramatic increase of the ultimate capacity due to the expanded base. Guidelines for the design of such piles are proposed.

Jan 1, 2010

By D. Michael Holloway

The California Department of Transportation (CALTRANS) evaluated several pile foundation schemes for supporting the structures along the realignment of Interstate 880. The project replaces the double-decked (Cypress) viaduct collapsed in Oakland, California during the 1989 Loma Prieta Earthquake. Structural support demands led to the selection of steel pipe piles (16-, 24-, and 42-inch-(406-, 610- and 1067-mm-)diameter), filled with concrete and steel reinforcement. Deep penetrations required through layers of very dense/cemented sands in some locations, caused serious drivability and pile integrity concerns. The need for large pile driving hammers and large diameter steel pipe piles pushed the engineers well beyond local experience. Such questions as the feasibility of driving the pipes closed-ended through dense upper strata and quantifying the effects of installation on the long-term capacities of the piles led Caltrans to develop a comprehensive pile test program to address the design and construction issues effectively. The results were furnished to prospective bidders on the production stages of the ensuing contracts.

Jan 1, 1995

By B. C. Slocombe

A large derelict inner city site was regenerated for use as a distribution warehouse. Difficult topography and soils conditions required the adoption of a combination of specialist geotechnical processes. Particular attention was paid to the preparation of the site, programming and capabilities of each technique as additional soils information became available.

Jan 1, 1989

By D. Arentsen

Changing environmental laws, new operating requirements and the increasing accuracy with which the bearing capacity of driven piles can be calculated have all led to the development of hydraulic piling hammers, some very primitive, others very advanced. Users find it difficult to decide which model is the most suitable, because the specifications are neither uniform nor unamiguous. There are no standard specifications and, moreover, the majority of hammers are suitable only for a limited range of applications. For the user, however, it is important to choose a hammer which will meet future as well as current requirements and will not quickly become obsolete or be unsuitable for a particular job.

Jan 1, 1987

By Patrick J. Hannigan

A comparison of 40 statically and dynamically load tested piles was performed to evaluate the variation between testing methods. This evaluation indicated an agreement of 10% to 15% could be obtained when the available static resistance is fully mobilized by both methods and when time dependent capacity changes are minimized. Dynamic pile testing recommendations for minimum induced impact force, ram weight to pile weight ratio, and considerations for time dependent capacity changes are presented.

Jan 1, 1987

By Rüdiger Wunsch

The new high speed Vienna - St.Pölten line and the Lainzer tunnel are to be connected to the existing Western railway line in Vienna. This involves building an underground cut and cover branching tunnel which will be connected to the Western railway line by ramps. A key structure is the Herzmansky Street tunnel, which has a length of some 820m. It is to be constructed as a cut and cover tunnel using the top down method. The walls of the tunnel are designed as a water resistant structure consisting of double walls, an outer wall of bored piles and an inner reinforced concrete wall. The bored pile wall will be used as a temporary retaining wall during the construction phase and will also be a structural part of the per­manent tunnel wall. The retaining walls of the open pit, which will have a depth of up to 14m and a width of 12m, were investigated as a non-contiguous bored pile wall and overlapped bored pile wall. Preventing ground water from penetrating into the pit is of paramount importance. The high ground wa­ter level is the determining factor for the dimensioning of the bored pile wall and results in the require­ment for a water resistant concrete structure. It has been necessary to adopt adequate measures, therefore, in order to reduce the hydrostatic water pressure during the construction phase, assuming economical pile dimensions.

Jan 1, 2000

By Peter Faust

The foundations for the new South Viaduct Bridge in San Francisco were extremely challenging due to the requirement for very large and deep piles installed adjacent to historic structures. Drilled shafts up to 12? foot in diameter were constructed to a maximum depth of 200? feet in alluvial soils and Franciscan Bedrock using an oscillator system for the installation of the permanent steel casing. This paper provides an overview of the construction techniques, the equipment, and the challenges associated with constructing 12? foot diameter shafts on this very complex project in one of the nation?s nicest landscape setting.

Jan 1, 2011