Search Documents

By Jeff Starchuck, Harald Kullmann

"In 2005, an inspection showed that the Deception Bay Wharf in the Canadian Arctic was at the end of its service life. Although Deception Bay is closed with landfast ice up to 5 ft thick, shipping operations continue year-round, with additional voyages in the summer open-water season to supplement mine supplies. The rehabilitation scheme that allowed minimal interruptions to shipping involved concrete caissons cast on barges and an ingenious placing system.WorleyParsons Westmar of Vancouver, B.C., performed the inspection under contract to the owner, Xstrata Nickel, Montreal, Quebec. The wharf, on the coast of the Nunavik region of Quebec, was originally constructed in 1971 for an asbestos mine, and is now used to support Xstrata’s Raglan nickel mine, importing fuel for p o w e r g e n e r a t i o n a n d general mine supplies, and exporting nickel concentrate to smelters in the south. Emergency repairs were essential to allow operations to continue at the site, while the parties considered permanent rehabilitation options and secured funding. The repairs were done in the openwater seasons, and included reinforcing the failed interlocks above water level with steel patch plates and injection grouting of the cell fill below the port crane in 2005. In 2006, workers installed a circumferential belting system below water level.Westmar held critical planning sessions with the mine operation personnel to find ways to stretch the limits of the mine supplies and nickel storage facilities. In the end, the parties agreed to shut down construction activities four times during the ice-free season to allow access to the dock site.Westmar developed a plan that allowed mine operations to continue during construction, and Xstrata approved the plan and budget in September 2006, for execution in 2007. Rapid construction was essential. To accommodate the short construction season and maintain minimum levels of service for the mine, the work was radically different from conventional Arctic deep-sea port construction. Like the original Deception Bay Wharf, construction practice was to use steel sheet pile circular cells with the consequential heavy support services for the labour force. Construction duration was typically two seasons. The plan for Deception Bay was executable in one season based on a concrete caisson structure. Only a modest amount of schedule float was needed."

Jan 1, 2009

By Richard Stone, Rouzbeh Afsharhasani, Moses Karakouzian

"Caliche, a hardened sedimentary deposit of calcium carbonate that occurs worldwide, generally in arid or semiarid regions, is frequently encountered in Las Vegas, Nevada. The presence of a caliche layer in a soil profile affects the response of deep foundations to axial load. This paper studies the stiffening effect of caliche layers on the elastic settlement of a pile foundation. In order to evaluate the response in a layered soil-caliche profile, finite element analyses were performed on a typical-sized single pile and a pile group, both having constant diameter and length of the pile. The results indicate that the stiffening effect from the caliche is noteworthy, and a layer with a relative thickness of at least one pile width, regardless of its location, reduces the pile settlement for both single piles and group of piles systems by at least 50%.IntroductionThe presence of cemented materials in the soil profile influences the settlement response of foundations. One type of cemented material that can be found in arid places around the world is a sedimentary deposit of calcium carbonate called caliche. Caliche, a hardened sedimentary deposit of calcium carbonate, is common in arid and semi-arid urban areas, such as Las Vegas, Nevada (Wyman, et al. 1993).Caliche is mostly observed in lacustrine, river, and alluvial fan deposits (Jr.C.C 1970). It is also found in Central and Western Australia, the Kalahari Desert, the High Plains of the Western U.S., and the Sonoran Desert of the U.S. and Mexico.Some conditions required for the formation of caliche are that country or basement rocks must be a carbonate type, carbonate must be present in the soil zone of the area, climate regime is semi-arid to arid, there exists widespread capillary activity, and carbon dioxide (CO2) is present in the environment. As a result, caliche occurs as a product of the carbonization process (Atabey, Atabey and Kara 1998). In such areas where foundations are constructed on thin rock layers (caliche), special geotechnical design conditions should be considered, particularly if the supporting rock layer is underlain by a weaker material."

Jan 1, 2015

By David T. Farber

"Stabilization of an existing cellular tower foundation system without dismantling the tower or compromising the existing foundation system was accomplished by installation of a jet grouted pile system. The tower was originally designed to be placed on a steep hillside and to be supported by a mat foundation founded on existing bedrock. The as-built conditions of the tower foundation system showed it to be constructed on a combination of loose fill of varying thickness and native stiff silts and gravel material. To avoid the potential of differential settlement, a jet grouted pile foundation system was installed to the top of bedrock. The jet grouted pile system was rapidly installed over a two-day period so as to not delay operational permitting of the tower.INTRODUCTIONA tri-legged lattice cellular communication tower was constructed on the side of a steep hill located in a mature hard wood forest. Access to the site as well as available work area was limited to small track type drill rigs and equipment. The original tower design required the tower to be supported by a mat foundation bearing directly on bedrock. Based on a review of the foundation construction and results of a subsurface investigation, it was discovered that the foundation was built directly over a loose fill material that varied in thickness from 0 to 4.27 meters (0 to 14-ft). Because of the uncompacted nature and varying thickness of the loose fill materials, the tower would be susceptible to differential settlement which, could lead to tower instability.The objectives of this project included the following:• stabilize the mat foundation against differential settlement without removing the existing tower structure or foundation system• rapidly complete stabilization activities to allow operational permitting of the towerSOIL CONDITIONSThe subsurface soil conditions that the tower mat foundation rested on were evaluated by installing three borings in a row from the inward slope portion of the mat foundation (B-1) to the outward slope portion of the mat foundation (B-3). Figure 1 illustrates the subsurface soil stratigraphy. The three borings encountered the following subsurface conditions:"

Jan 1, 2005

By Adnan A. Malik, Tadashi Maejima, Jiro Kuwano

"The use of steel screw piles has greatly increased in recent years because of the advancement in the installation mechanism and its performance under compressive, uplift and lateral loads. In a steel pile system, the strength of pile material limits the end bearing resistance of the pile due to strong subsurface conditions. The installation mechanism of screw pile can reduce the end bearing resistance due to the torque and axial force. However, if the installation mechanism does not reduce the bearing resistance of the pile, another important factor that can reduce its performance is the strength of the helix/wing plate. In this study, the effect of wing plate deformation on the performance of single helix/wing plate pile bearing resistance investigated. A model ground was used to investigate the effect of wing plate deformation. Dry Toyoura sand was used as a ground material and was compacted to denser states of 80% and 92%. The shaft and wing plate material of the pile was the same to actual piles that are used nowadays in Japan. A series of load tests were performed with different wing plate diameters and thicknesses. It was observed that deflection in the wing plate reduces the bearing resistance of the pile. The increase in the thickness of the wing plate was seen to restore the reduced pile resistance due to deflection. It was also observed from the experimental results that the ratio of wing plate diameter to shaft diameter (Dw/Ds) greatly affects the deformation of wing plates, which ultimately affects the end bearing resistance of the pile. The results obtained in this research suggest that the outstand length (Lw) of wing plate should be less than 5.6 times the thickness of wing plate for piles having a large Dw/Ds ratio under strong ground conditions.INTRODUCTIONThe first use of screw pile was almost 180 years ago by Alexander Mitchell. He patented his invention in 1833 with the name “Screw Pile”, and used it for ship moorings. The use of screw piles has since been adopted in various areas such as lighthouses, fencing for agriculture and marine structures. The use of screw piles in civil works started in 1985, after the invention of the hydraulic torque motor, as it eases the installation process. Nowadays, screw piles are used in the foundation of transmission towers, elevators, buildings and many other civil structures.Screw pile has an edge over other steel pile systems due to its high bearing, uplift and lateral resistance. The end bearing resistance of screw pile depends on installation, strength of subsurface material and the pile material. The screw pile is installed by applying torque and axial force. The pile torsional strength should be more than the applied torque and axial force to avoid deformation before reaching the final depth."

Jan 1, 2015

By Toshio Yonezawa, Helmut Florian, Herbert Kuh, Masamichi Aoki, Takao Koono, Franz-Werner Gerressen

"To increase the bearing capacity of the ground, soil improvement technique is often adopted. One advantage of soil improvement techniques is the fact, that the impact to the environment is low, as the system utilizes the existing soil. Recently, compressive strength of soil improvement gets more into the focus for the use of building foundation. To prevent brittle fracture, which is a weak point of soil improvement, fiber reinforced soil improvement has been developed. Laboratory tests were conducted to examine the fibers suitable for reinforced soil improvement, and examine the optimum mix design for fiber cement slurry. Based on the laboratory tests, polypropylene fiber and cellulosic viscosity admixture was selected. For the laboratory tests a scaled model of CSM mixing head was used to examine the dispersion of the fibers in the ground. Using the CSM mixing head, the outer periphery fibers of soil improvement seemed to be arranged in the vertical direction, toughness performance of the soil improvement could be improved. Furthermore, full scale field test was performed using actual CSM unit, modified to enable the use of fiber mixed slurry. The validity of the material as well as the toughness performance of the soil improvement, determined from lab test results, was confirmed. In addition, it was confirmed that fiber reinforced soil improvement can be constructed appropriately by CSM method.2 INTRODUCTIONSoil improvement technique to improve the strength and deformation performance of ground has been used for a long time. Cement improved methods, with the increase of the deep Mixing Method, which has been disseminated since the 1970's, was often used since. Cement used soil improvement technology has been utilized to stabilize excavations, slopes in embankment and much more. Recently, it can be used for preventing liquefaction by building soil improvement in a grid (Suzuki et al. (1996)), and also as basis of the structure by increasing the compression strength of soil improvement (Yamashita et al. (2011)). Cement used soil improvement method, a technique for mixing the in-site soil and cement, can effectively utilize natural resources, and it can be expected that its use will increase further in the future. Therefore, soil improvement technique will be able to minimize the impact on the environment. Cement improved soil is a mixture of soil particles and cement with high compressive strength but low tensile strength. Since tensile strength of soil improvement is low, brittle destruction occurs. Therefore, it is not possible to use soil improvement in conditions acting with bending stress. If a horizontal impact force occurs in the improved soil, the width of the soil improvement needs to be increased to reduce the bending stress. If preventing the brittle fracture of soil improvement, the width of soil improvement could be reduced, then less resources would be needed. In order to increase the tensile strength of the soil improvement, several studies for the mix of fiber and soil were performed. Victor (1992) indicates cracking deterrent effect by fiber based on laboratory tests. Moreover, based on laboratory tests, Hayasaki (1982) illustrated the effect on the tensile strength of the fiber types, the type of fiber, the diameter of and the length of fiber."

Jan 1, 2015

By Md. Nafiul Haque, Murad Y. Abu-Farsakh, Chris Nickel

"This paper presents the results from a pile load testing program for a bridge construction project in Louisiana. The testing includes two 54-inch open-ended spun cast concrete cylinder piles (OECP), one 30-inch open-ended steel pile (OESP), and two (30-inch and 16-inch) square prestressed concrete (PSC) piles driven at two locations with very similar soil conditions. All the test piles were instrumented with vibrating wire strain gauges to measure the load distribution along the length of the test piles and the skin friction and the end bearing were derived from strain gauge measurements. High strain dynamic load tests (HSDLT) were performed on all test piles at different times after pile installations to quantify the amount of setup with time. Static load tests were also performed on the PSC and open-ended steel piles. Due to expected large pile capacities, the statnamic test method was used on the two open-ended cylinder piles. The pile capacities of these piles were evaluated using various CPT methods (such as Schmertmann, De Ruiter and Beringen, LCPC, COFS methods). The result showed that all the methods can estimate the skin friction with good accuracy; but not the end-bearing capacity. Setup was observed for all the piles, which was mainly attributed to increase in skin frictions. The setup rate parameters “A” [The “A” parameter is defined as the rate of increase of pile capacity ratio (Rt/Rto) per log cycle of elapsed time] were back-calculated for all the test piles and the values were between 0.31 and 0.41.INTRODUCTIONDue to greater efficiency (capacity to weight ratio) of the pipe piles, open-ended piles are a viable option to solid piles. However, the behavior of open-ended piles is more complicated compared to the close-ended piles owing to possible formation of “soil plug” inside the open-ended pile. Many researchers have analyzed the behavior of both types of piles for different purposes; however, very few studies in the literature offer the side-by-side comparison of the close-ended and open-ended piles."

Jan 1, 2017

By Daiki Takano, Naoki Takahashi, Hidenori Takahashi, Ikuo Towhata, Yoshiyuki Morikawa

"The method in this study, in which cement-treated piles are installed into the ground to decrease the amount of liquefied lateral flow, has been studied. The authors are also investigating the most effective arrangement of piles to optimize cost-effectiveness. In their investigation, they propose shifting the position of the piles to prevent lateral flow in various directions. The present study conducted centrifuge model tests to clarify the improvement effect of piles against the lateral flow of liquefied soil and the effect of the pile arrangement. Then, numerical fluid analyses were conducted to consider the improvement mechanism. As a result, the model tests and numerical analyses showed that the pile improvement dramatically reduced the lateral displacement and that the average total flow velocity decreased in the irregular case.INTRODUCTIONLiquefied ground subjected to seismic motion loses its stiffness and strength, and lateral flow often occurs in sloping areas and backfill areas behind collapsed quay walls. In the Hyogoken–Nanbu Earthquake in 1995, the reclaimed island that was surrounded by collapsed quay walls expanded toward the sea and the amount of displacement reached a few metres (Hamada et al., 1996). Two countermeasures can be considered to guard against lateral flow: preventing liquefaction and reducing lateral displacement. The former method is ideal; however it is costly and time-consuming. Based on these considerations, the authors (Takahashi et al., 2013; Morikawa et al., 2014) are currently studying a method in which cement-treated piles are installed into the ground (see Fig. 1) to decrease the amount of liquefied lateral flow. The countermeasure cost using this method is relatively low because of the low replacement ratio. The authors are also investigating the most effective arrangement of piles to optimize cost-effectiveness. It has been proposed that the position of the piles should be shifted so that lateral flow can be prevented in various directions, as described in Fig. 2."

Jan 1, 2015

By Dan Brown

Improvements in construction equipment and techniques in recent years have made possible the use of drilled shaft foundations in diameters and lengths not previously considered practical or feasible. Many highway bridge and other structures are now routinely founded on drilled shafts which are 2.5 m to 3.0 m (8 to 12 feet) in diameter and extending over 60 m (200 feet) in depth below grade. There are unique challenges associated with constructing such large and deep cast-in-place foundations and engineers should be aware of the special needs associated with site investigation, construction specifications, material requirements, and quality assurance. This paper outlines a number of special considerations for these foundations, along with strategies that may be employed to improve the reliability and quality of large drilled shaft foundations.

Jan 1, 2008

By Chengcan Wang, Jin-Tae Han, Young-Eun Jang

"The waveform micropile is a newly developed foundation type for increasing the bearing capacity with the created shear keys on the pile’s shaft. Analyzing the increment of resistance at the shear key zone is a crucial factor in the design of the waveform micropile. Hence, centrifuge tests were carried out employing six different models, including a waveform micropile in the axial loading condition. The analysis results of the load-settlement curves showed that the waveform micropile achieved a higher bearing capacity compared to the micropile without shear keys. In addition, the test results revealed that the load-settlement relationship was affected not only by the pile shape but also by the locations of the shear keysINTRODUCTIONA micropile is a small-diameter pile, typically constructed with a less than 300 mm diameter. Generally, the micropile’s construction involves drilling, grouting, and insertion of a reinforcement material, such as a thread bar. The micopile can be utilized in a variety of fields for reinforcing the foundations of existing structures. It also has advantages for accessing challenging areas like limited-access construction sites, including those with a low headroom space and adjacent structures, due to the small size of the construction equipment. Thus, since it was introduced in 1950 in Italy, the micropile has become one of the preferred solutions when other deep-foundation methods are not applicable to the site.Federal Highway Administration (FHWA) gives the micropile design implementation guideline of neglecting the end bearing due to its small diameter but considering the frictional resistance if the bond zone of the pile is in the soil or on a weak rock. The bearing capacity is considered primarily only if the micropile is founded on a high-quality sound rock (FHWA, 2005). Micropile design in South Korea is currently being performed based on the FHWA manual and taking into consideration the frictional resistance for the design as the pile generally sockets into a weak rock or soft rock. Moreover, the frictional resistance within the soil layer has usually been ignored, considering only the shaft resistance of the rocksocketed length in the conservative design. The design concept excluding the frictional resistance in the soil layer, however, may lead to an extension of the pile socket length, which will increase the construction cost. Hence, many researches have attempted to provide better design and construction methods to increase the bearing capacity in a cost-effective way (Juran et al. 2001; Sadek and Isam 2004; Tsukada et al. 2006; Finno 2002; Gomez et al. 2003; Seo et al. 2013)."

Jan 1, 2016

By Jim Bruce

This paper presents details of a slope stabilization scheme built in late 2003 at a 16m-high railway embankment in southern Ontario, Canada. The owner, faced with continuing maintenance and safety issues arising from numerous nuisance slides, and residential neighbors in close proximity to the slope, sought new proposals to replace a previous recommendation to cut down all trees and undertake a deep soil nailing scheme. A non-reticulated micropile array with surface cap beam was proposed and built on the south side of the embankment with no tree removal required. A detailed FLAC analysis was completed, using multiple iterations to arrive at the eventual, optimized micropile depth and spacing. Analysis predicted an 18% increase in the factor of safety. Short term inclinometer monitoring and performance evaluations in the months since construction so far corroborate the prediction.

Jan 1, 2004

By Joseph T. Coe, Siavash Mahvelati, Philip Asabere

Characterization of existing foundations remains an important issue as foundation reuse and rehabilitation continue to garner increased attention. In the case of unknown foundations, geophysical and nondestructive testing (NDT) methods have been utilized in the past to evaluate foundation geometry and could serve as useful tools in the case of foundation reuse. A comprehensive study was initiated in the late 1990’s and early 2000’s that evaluated the effectiveness of the available geophysical and NDT technologies to characterize unknown foundations for scour evaluation purposes. At the time of that study, the Multichannel Analysis of Surface Waves (MASW) geophysical method was in its infancy and not widely used. Since then, MASW has become increasingly prevalent in geotechnical applications as the method presents a number of potential advantages when characterizing the subsurface, including rapid testing, increased signal to noise ratio, and ability to resolve velocity inversions. This paper presents a case study that explores the abilities of MASW as an unknown foundation characterization tool. MASW was applied to determine subsurface stiffness at a bridge foundation site in the Philadelphia metropolitan area. One MASW survey line was performed immediately over the foundation of interest and another was performed over a control zone adjacent to the foundation to establish a baseline site profile. The purpose of this testing was to examine whether MASW could establish the geometry of the foundation at this site. This paper presents the site conditions and MASW testing procedures, followed by a discussion of data analysis and interpretation.

Jan 1, 2016

By Fredrik Sarvell, Harald. Ihler, Veli-Matti Uotinen, Jukka Rantala

"Many of the valid international building codes state that the lateral support provided by the soil is sufficient to prevent buckling of fully embedded piles. However, the development of small diameter micropiles and especially the use of high strength steel have evolved to applications including high capacity elements. The ultimate structural load bearing capacity of a pile in a cohesive soil is decided by examining which gives the lowest value, the peak buckling load and the resisting moment provided by the surrounding soil medium or the structural capacity of the pile cross section. In both cases, the initial deflection of the pile is a significant factor when the axial load bearing capacity of the pile is determined. Steel micropiles are joined commonly with mechanical splices. A less rigid mechanical splice is often a weaker hinge that allows the pile to bend and deflect more during installation increasing the initial deflection of a pile. In addition the less rigid splice element decreases the bending capacity of a jointed pile section and the ultimate axial load capacity of the entire pile. A series of FE analysis performed for various pile sizes suggest that the steel pipe piles including separate pile sections and mechanical splicing elements should have the combined bending stiffness of EIshaft = 0,75 × EIpile. This requirement yields to the buckling resistance of at least 96 % of the solid reference pile with the sameinitial eccentricity in similar soil conditions.IntroductionMany of the valid international building codes state that the lateral support provided by the soil is sufficient to prevent buckling of fully embedded piles. However, the development of small diameter micropiles and especially the use of high strength steel have evolved to applications including high capacity elements. The potential buckling of these very slender high capacity piles in soft soils may in many cases be the controlling design factor of the pile, especially with end bearing micropiles.A typical sequence of soil strata in Nordic countries, such as Norway, Finland and Sweden, constitutes of friction soil or dry crust clay on top of soft clay followed by till. This soil stratum often rests on solid bedrock of granite or gneiss. Conditions like these are suitable for slender end bearing piles subjected to buckling and especially steel pipe piles where most of the material is located at the edge of the cross section. Other reasons for using slender steel pipe piles are for example fast installation with minimal waste, efficient manufacturing and relatively well established design and execution procedures. Minimum quality criteria’s regarding splices for steel pipe piles are recommended to be set as national provisions to ensure quality and comparable procurements in foundation business."

Jan 1, 2014

By James P. Hambleton, Sam A. Stanier

A perceived advantage of screw-type foundations is the ability infer aspects of foundation performance from quantities measured or observed during installation, especially the installation torque. A particular concept widely used in practice is to correlate installation torque to ultimate capacity. This notion has proven useful as a field verification technique despite the absence of validated models that relate key variables of interest, such as installation torque, axial (crowd) force, geometrical parameters, and soil strength. This paper considers previous work by the co-authors and collaborators on analytical, numerical, and physical modelling of screw piles to relate the quantities measured or controlled during installation (e.g., installation torque) to the ultimate capacity and soil strength. Attention is given to saturated clay as a particular soil type amenable to simplified analysis. An analytical model for a single-helix pile is considered as a means of directly relating the ultimate capacity and undrained shear strength to the installation torque, crowd force, plate pitch, plate diameter, shaft diameter, installation depth, and surface roughness. The connection between the installation variables and ultimate capacity—and the sensitivity to crowd force in particular, a quantity that is typically not measured during field installations—is also discussed. The theoretical predictions are compared against data obtained from small-scale laboratory experiments that suggest the installation torque relates to the remolded strength of the soil. INTRODUCTION Screw piles are deep foundations that are twisted into the ground through an applied torque. Advantages over driven piles or drilled foundations include the relative silence of the installation, with low ground vibrations, and the possibility of being easily decommissioned by reversing the direction of twisting. Screw piles are now routinely encountered as a flexible, low-cost solution for numerous applications (Figs. 1 and 2), and they are also being considered for applications in offshore energy production due to limitations being imposed with respect to decommissioning and underwater noise. Also known as “screw anchors,” “helical piles”, or “helical anchors,” screw piles consist of helices or helical plate elements attached to a central shaft. Figure 3a shows the components of a single-helix pile and key variables. The diameters of the shaft and helix are denoted by d and D, respectively, and p is the pitch of the helix. Variable H denotes depth of the helical plate, and T and N denote the torque and axial (crowd) force applied during installation. In typical applications, the pile includes multiple helical plates, and the shaft is composed of segments that allow for it to extend to large depths into the soil.

Jan 1, 2019

By Kessi E. Zicko, Eric A. Hackenberg, Paul J. Lewis

"Following snow melt and spring rains in 2011, a landslide measuring approximately 600 feet long and 300 feet in slope length occurred within the southbound roadway embankment of a heavily travelled 2-lane divided highway in North Central Pennsylvania. Driven steel piles were designed to stabilize the embankment slope. Factors affecting the selected stabilization technique included an adjacent reservoir, wetlands, the length and depth of the failure plane, extent of glacial lake deposits, excess pore pressures in the foundation soils, and an area of archaeological interest. Field reconnaissance and subsurface explorations including borings, instrumentation, geophysics, and laboratory testing indicated that glacial lake deposits were present in the toe region of the embankment. Instrumentation proved key in measuring excess pore pressures and in locating the failure plane, and geophysics was utilized to estimate the extent of the soft glacial lake deposits and to estimate pile lengths. The existing condition of the embankment was modeled in computer slope stability analyses, which were also used to help assign soil parameters. Significant costs were associated with constructing a berm due to the impacts on adjacent site features. Therefore, multiple rows of driven steel H-piles were designed for installation along the toe of the embankment. The design lateral load in the piles was based on slope stability analyses, and the pile size and number of piles were based on lateral pile computations with modified p-y curves to account for installing piles in an active landslide. The relationship between the factors of safety from slope stability and the LRFD pile design was significant in determining pile loads for lateral analyses.INTRODUCTIONA landslide developed along the lower portion of the southbound embankment of State Route 15 in Tioga County, Pennsylvania. The road passes through a steep valley and is located along the southern extent of the Tioga Reservoir. Although no damage to S.R. 15 was attributed to this landslide, the close proximity of the slide to the road posed a concern for the long-term stability of this section of roadway.This paper presents a summary of the site history; the subsurface conditions based on borings, instrumentation, a geophysical survey, and laboratory testing; slope stability analyses including alternatives assessment; and the pile design.SITE HISTORYS.R. 15 was originally located in the valley along the Tioga River and traversed through the towns of Tioga and Mansfield. Although the reason is unknown, it is interesting to note that Old S.R. 15 curved away from the river in the area of the landslide. In the mid 1970’s, S.R. 15 was relocated to the eastern hillside prior to construction of the Tioga-Hammond Reservoir by the U.S. Army Corps of Engineers. The relocated highway was constructed in stages. Two lanes of relocated S.R. 15 were initially constructed to carry one lane of northbound and one lane of southbound traffic. At this same time, the majority of the fill was placed for two future lanes immediately to the west, which would eventually allow for two lanes in each direction. The two eastern lanes would then carry northbound traffic after completion of the two southbound lanes to the west."

Jan 1, 2015

By Massimo Poggio, Gabriele Balconi, Andrea M. R. Pettinaroli, Mario Ruggiero, Riccardo Castellanza

Grouting technologies are ground treatment techniques used for modifying the behaviour of a mass of soil or rock by injecting a mixture. The sleeved port pipes (also called Tube A Manchette) are highly diffused for grouting treatment of coarse soils and fissured rocks. This paper describes a combination of jet grouting and rock grouting with MPSP (multiple packer sleeve pipe) technique that has been used to realize waterproof curtains under fluvial structures for a cascade hydro-power plant. This is composed by five mini hydro-power plants, placed along the Iskar River, in Bulgaria, and composed by a penstock followed by the power house, a spillway, and an earth dam containing the reservoir. The geology of the site is characterized by an upper alluvial deposit lying over the bedrock. In each site, similar treatments were carried out: an impervious curtain along the plant section, obtained by executing jet-grouting columns in the surficial alluvial layers and grouting the underlying fractured rock by means of port pipes. The temporary embankment, built during the works for protecting each site from the possible river floods, has been waterproofed and stabilized by reinforced jet-grouting columns. The grouting processes have been controlled and monitored by a computerized system. INTRODUCTION The Iskar river cascade hydropower plant is situated northern of Sofia, Bulgaria, and it is composed by nine plants. Actually five of them have been built and produce energy. Each plant is composed by a penstock followed by the turbine building, a spillway, and an earth dam that contains the reservoir. The Iskar rivers runs in a narrow valley characterized by diorite or diabase rocks, with an upper deposit of alluvial soil, composed mainly by gravel and sand. Each plant requires an impervious curtain under the structures and in correspondence of the earth dam: this has been obtained by means of a jet grouting treatment of the alluvial coarse soil, and a grouting treatment with cement mixtures of the underlying rock using the MPSP technology. During the construction of the structures, the site has been shielded from the river water by a temporary earth embankment that has been statically improved and waterproofed by jet grouting columns reinforced with steel tubes; this allowed to work without interruption even in case of flood of the Iskar river.

Jan 1, 2019

By Armin W. Stuedlein, Jim Zammataro, Bernie Hertlein, Daniel Belardo, Qiang Li, Antonio Marinucci

"An experimental program focusing on four drilled shafts was conducted to determine the effect of high strength steel reinforcement bars on lateral resistance, steel casing on axial and lateral resistance, and steel casing without internal reinforcement on lateral resistance. Thermal Integrity Profiling (TIP) Thermal Wires and crosshole sonic logging (CSL) access tubes were installed in each shaft, and thereafter the corresponding non-destructive testing (NDT) was performed on each shaft to assess the integrity of the shafts and to compare the results from the different NDT methods. The results of the CSL tests using scored PVC tubes are compared against those conducted in 73/56 fully-threaded steel hollow bars, whereby the results indicated that the threaded bars served as a good host for performing the CSL tests. The data from the TIP Thermal Wires is compared against the results from the CSL tests for each of the four shafts, and the similarities and discrepancies between the two methods are discussed. This paper will serve as a reference to those interpreting the measurements and data obtained by performing nondestructive integrity tests on drilled foundations.INTRODUCTIONNon-destructive tests (NDTs) embody a set of critical tools for the evaluation of the integrity of constructed deep foundations, particularly for cast-in-place foundation elements. Construction defects may require the rejection of the foundation element by the owner’s representative, resulting in costly repairs or replacements and delays to the project schedule. The use and appropriate interpretation of the results from the NDTs provide the information required when evaluating the integrity of these constructed elements. A cooperative research program was conducted to assess the effects of various construction variables on the axial and lateral performance of drilled shaft foundations, which provided an opportunity to compare the established Crosshole Sonic Logging (CSL) test method to the newer Thermal Integrity Profiling (TIP) Thermal Wire method. This paper presents an overview of the experimental program performed at the geotechnical test site at Oregon State University (OSU), details of the CSL and TIP installation and testing methods, and the results of the NDTs on the constructed drilled shafts. Because one of the shafts was constructed with fully-threaded longitudinal steel hollow bars, this experimental program also allowed the assessment of the use of the hollow bars as access tubes for the CSL tests. Both the CSL and TIP test methods indicated that the shafts were of good quality and free from defects or anomalies; the data obtained using the TIP method also provided an estimate of the as-constructed shaft diameter and the reinforcement cage alignment, which will prove helpful when back-calculating axial and lateral load transfer during future loading tests."

Jan 1, 2016

By Adel M. Hanna, Ibrahim M. Mashhour

"Collapsible soil is known as one of the difficult soils, which possesses considerable strength when it is dry and significantly reduced when inundated. In practice, in case of a thick layer, pile foundations are often used to penetrate the collapsible soil to firm soil/rock strata. Inundation of collapsible soil is accompanied by a large and sudden settlement, which may significantly increase the negative skin friction and accordingly the drag loads on the pile’s shaft. Inundation may take place from the running surface-water or raising the groundwater. In case of surface water, the amount of settlement varies, depending on the extent of the wetted zone and the degree of saturation in the soil, while rising groundwater will produce full saturation in the ground and accordingly larger settlement.In the literature, there is lack of reports dealing with the prediction of the drag load on piles in collapsible soils subjected to inundation. This is due to the complexity of modeling collapsible soil analytically. Alternatively; the results of a sophisticated experimental investigation may guide the researcher to develop a model to predict the drag load on these piles.This paper presents the results of a small-scale experimental investigation tailored to measure the soil collapse during inundation and the associated drag load on an endbearing pile’s shaft. Based on the results of the present investigation, the effect of the soil collapse potential and the pressure acting on the soil during inundation on negative skin friction is presented.INTRODUCTIONCollapsible soil is a metastable material, traditionally defined as unsaturated soils that experiences a radical rearrangement of particles and significant reduction of volume upon wetting with or without loading (Bara 1976; Houston et al., 1988). A wide range of soils fall into the category of collapsible soil, including naturally existing types of soils such as: Alluvial flood plains, mud flows, residual soils, colluvial deposits, fans, aeolian or wind-blow deposits sands and silts (loess), volcanic tuffs, gypsum, dispersive clays, loose cemented sands , sodium rich montmorillonite clays (Clemence and Finbarr 1981).Soil wetting and soil saturation may take place as a result of urbanization or natural causes, such as: groundwater level rise, landscape irrigation, broken water pipelines or sewer lines, poor surface drainage, groundwater recharge, cut/fill construction, and moisture increase due to capillary rise. The severity of the outcome depends heavily on the so called collapse potential of the soil, which depends mainly on; soil type, compaction effort, initial water content and stress level at soaking (Houston and Houston, 1997; Ayadat and Hanna, 2007)."

Jan 1, 2015

By D. Dreher Whetstone, Paul M. Blakita, Christopher M. Reith, Ravi P. Malviya

"Micro-piles are small diameter (5 to 10 inches), cast-in-place piles which can develop high load capacities by bonding with soil or rock. Micro-piles are particularly well-suited for moderate to heavily loaded structures requiring deep foundations in difficult subsurface conditions, such as karst, bouldery mine spoil, or unsuitable fills with concrete debris or other obstructions. Attempts to install conventional deep foundations including driven piles, drilled piers, or auger-cast piles are likely to be fraught with construction difficulties and disputes, delays, cost overruns, and may be unfeasible in some cases. Micro-pile installation equipment is very effective in installing foundations through such overburden or rock materials.This paper presents case histories of Micro-pile installations on two projects with difficult soil/rock materials. The project sites are located in Charles Town, West Virginia and Masontown, Pennsylvania.Charles Town, West Virginia ProjectThe Charles Town project entailed construction of a four-story pre-cast concrete garage. Triad Engineering, Inc. performed a geotechnical investigation for this project (Triad, 2001). The subsurface, geologic, and project specific information described in th is paper are largely based on the aforementioned geotechnical report.Ground ConditionsThe project site is located in Jefferson County, West Virginia, and is mapped to be underlain by the Elbrook Formation. This formation is described as argillaceous, dolomitic limestone with beds of dolomite and aphanitic and algal limestone (Dean, et al. , 1990). The carbonate rocks at the site were characterized as ""moderately solution-prone, highly calcareous and weathers differentially to produce a pinnacled or ""sawtooth"" top of rock profile. (Triad, 2001 )"" Overburden soils consist of low to high plasticity, fine grained residual soils formed by weathering of the parent carbonate rock. The residual soils include variable proportion of sand and rock fragments."

Jan 1, 2005

By Brian W. Wilson

A case study is presented that describes the design and implementation of a combined blast densification and deep dynamic compaction program which was undertaken to improve the foundation soils for a proposed tailings dam raise in Ontario, Canada. Based on the results of the geotechnical investigation it was determined that the foundation of the dam would be situated on tailings of both variable thickness and density, much of which would be susceptible to liquefaction under the design earthquake for the region and type of facility. Blast densification trials were completed by the owner and the results of these made available to prospective tenderers in response to a call for a fixed price contract for the design and implementation of a densification program for approximately 800,000 m3 of foundation tailings. The variation in tailings gradation and the impacts of such on the ground improvement program are discussed, as are details of both the additional blast densification field trials completed by the contractor, and the selected blast pattern and explosive charging used for production blasting. The applicability of the various ground improvement techniques to the actual conditions encountered, and the results obtained are also discussed.

Jan 1, 2010

By Raffaella Granta

Mosul Dam is an earth fill dam located on the Tigris River, approximately 40 km (25 mi) northwest of Mosul, Iraq. The construction of the dam was completed in 1984. It is one of the largest multipurpose dams in the Middle East, and the largest dam in Iraq. The dam provides flood control, irrigation, power generation and water supply. At 113 m (371 ft) high and 3.65 km (2.3 mi) long, the reservoir has a storage capacity of 11.1 billion m3 (392 billion ft3) of water. The main hydroelectric power station has four turbines for an installed capacity of 750 MW. The discharge system includes two bottom-outlet tunnels of 10 m (33 ft) diameter, a five-gate service spillway and an emergency fuse plug spillway.

Oct 1, 2022