Search Documents

By Sandra L. Mesa-Espitia, Gretchen T. Lapidus

Gold present in arsenopyrite matrices is refractory and requires highly oxidative pretreatments in order to obtain acceptable degrees of extraction. However, these release many byproducts that are harmful to the environment. In the present work, a high-grade arsenopyritic ore was pretreated with different solutions, containing hydroxide ion, EDTA, oxalic, tartaric, or citric acids, to improve gold extractions in a posterior leaching step. The pretreatments were carried out at room temperature for 24 hours with a respective ligand concentration of 0.25 M. Once completed, the residue was leached in a thiosulfate solution to quantify the effect of the pretreatment on gold extraction. Only 29% of the gold content was leached, with very slow kinetics, in the untreated mineral. However, after pretreatment with tartaric or citric acid, the kinetics improved, although the percentage of gold extraction only reached 42-45%. The highest gold recovery, with very rapid kinetics, was found with the oxalic acid or the hydroxyl ion pretreatment (70 and 62%), respectively, but also corresponded to the most arsenic co-dissolution.

Jan 1, 2014

By Bradford P. Simser

The theoretical capacity of various ground support components can be misleading, especially in bursting ground where the failure mode is often in the retainment system. Wire mesh screen seams often peel open rather than breaking the wire strands, fractured rock often un-ravels around the bolts rather than breaking the bars. If a weak link(s) in the system fails prematurely, then the potential capacity of the system may never be fully realized. Underground observations are used to show how some support systems behave in the field. Various combinations of wire mesh screen with friction bolts, rebar, modified conebolts, cablebolts, shotcrete and mechanical rockbolts are considered. A short case history is used to contrast the performance of ?just-intime? development in a high stress faulted area versus a tunnel subjected to multiple stress changes in a similar environment. The latter proved to be a serious ground support problem when the well developed fracture zone around the opening was subjected to dynamic loading from a large seismic event causing a severe rockburst. In such cases an improved mining strategy may be more relevant than higher capacity support systems.

Feb 1, 2008

By Hani S. Mitri

Strainbursts in brittle rock are common to deep underground mines. The state of stress at the boundary of mine openings is dictated by a biaxial stress/loading condition. This paper reports the results of a series of biaxial compression tests carried out on 100 mm cubic samples of norite rock, under different horizontal-to-vertical stress ratios. The results indicate that the biaxial compressive strength is considerably higher than the uniaxial one. It is found that the norite sample behaviour under biaxial loading mirrors field behaviour where shearing and progressive spalling of the opening boundary are observed prior to strainbursting. Sample failure is initiated by rock spalling at the sample free faces, i.e. in the plane of biaxial loading. Finally, it?s the out-of-plane shear failure mechanism that causes the sample to collapse. Shear failure takes place violently and abruptly and is accompanied with considerable audible noise.

Apr 1, 2005

By D. Nie, M. Ren, T. Mo

This paper studied the phenomenon of room temperature creep deformation at crack tip and its effect on fatigue crack growth rate of a X-70 pipeline steel using compact-tension (CT) specimen on a MTS 810 testing machine. Time-dependent deformation at the crack tip under constant load was observed in this steel at room temperature and the amount of deformation produced was seen to depend on loading rate and the magnitude of stress intensity factor. It is found that there exists a critical stress intensity factor below which the deformation decreases with time when the applied load remains constant. It is also found that the occurrence of room temperature creep obviously affects the subsequent fatigue crack growth rate. The observed behavior was explained based on dislocation theory.

Jan 1, 2005

By Zhang. L.

Ordered intermetallic PtSb had been synthesized by arc-melted and then sintering treatment. The electro-oxidation of formic acid on PtSb was investigated at room temperature by cyclic voltammetry and chronoamperometry. The results are compared to those at a polycrystalline platinum electrode surface. It was found that PtSb intermetallic was catalytically more active than pure platinum according to the onset potential and current density. XRD and XPS technologies had been used to investigate the crystal structure and electron effect. We think formic acid decomposition on PtSb favors the reactive intermediate route and is not very much affected by the CO intermediate as compared to Pt.

Jan 1, 2005

By P Kovacs, D. L. Flock

For the purpose of reservoir-performance calculations a balance can be made between the materials with-in the reservoir and the production from the reservoir. The material balance equation, a relationship which holds under or near equilibrium conditions, has been used in many forms by the Petroleum Engineer for the determination of initial oil-in-place in the reservoir and the calculation of performance into the future. One of the more recent methods developed by Tracy, utilizes a modified form of the Schilthuis material balance. In the latter case, values of incremental production are assumed for a particular pressure drop, a value of the gas-oil ratio found and a check of this estimate made by calculation"' the initial oil-in-place. Tracy's method utilizes an estimation of the instantaneous gas-oil ratio and by trial and error a value of the gas-oil ratio is

Jan 1, 1961

By Q. B. Li, B. Gonçalves da Silva, J. T. Germaine, H. H. Einstein, Z. Moradian

"Shale gas and oil production has grown rapidly in recent years, and consequently there are increasing demands to understand the mechanical and microseismic properties of shale. Acoustic emission (AE) monitoring provides useful information on the fracture mechanisms of shale rocks, and provides a basis for interpreting field seismic observations. While there have been attempts for microseismic monitoring of conventional hydrocarbon reservoirs, shale presents a large number of issues that require further investigation. For this purpose, experiments were conducted to understand the characteristics of the AE waveforms propagated through Opalinus shale rock in the time and frequency domains. Frequency range, arrival time, first arrival amplitude and other parameters such as counts, duration and energy of the waves generated from artificial and natural sources in the shale specimens were detected and compared with AE characteristics of granite, a brittle rock that has been extensively investigated. The experimental tests showed that there are some important factors that influence the analyses and interpretations of seismic surveys and microseismic monitoring of shale compared to granite. One of these factors is the anisotropic behavior of shale that causes the wave to propagate with different velocities in different directions. Also bedding planes and micro-discontinuities in the shale cause attenuation of the waves. Thus the AE waveforms that arrive at the sensor are a distorted and attenuated versions of the source waveform.INTRODUCTIONMonitoring microseismic activity from hydraulic fracturing of shale provides vital information for mapping injection paths and fluid migration in order to check the effectiveness of the hydraulic fracture stimulation. Analysis of microseismic source locations can be used to identify fracture networks induced or mobilized during the hydraulic fracturing operation (Rotherd and Shapiro, 2003). On the other hand, by monitoring and assessing detected signals from hydraulic fracturing one can evaluate the induced seismic impact of the stimulation operation.While there have been attempts to monitor microseismic events in conventional hydrocarbon reservoirs, shale presents a large number of issues that require further investigation. For this purpose, experiments were conducted on Opalinus shale to understand its acoustic emission (AE) characteristics in the time and frequency domains."

Jan 1, 2015

By Ahmad Abdollahi

Many factors affect mechanical properties of hypoeutectic Al-Si alloys. As examples the presence of impurities such as Mn and Fe due to the formation of intermetallic phases, additions of small amounts of alkaline earth metals and cooling rate in consideration of Si formation, they all have an impact on mechanical properties of hypoeutectic Al-Si alloys. In this investigation, the effect of Fe content into the specification range of A357 alloy, the addition of different modifiers consisting of Na, Sr and Ca for the alloy of A356 and different mounting techniques for separately cast test coupons of hypoeutectic Al-Si alloys using the lost wax method were studied. The results showed that using material with lower Fe content and addition of modifiers improve mechanical properties. Also different mounting techniques resulted in different mechanical properties.

Jan 1, 2004

By David McMullen

Radiation plays a critical role in the thermal behaviour of hydrometallurgical process equipment. This effect is particularly important when designing refractory lined equipment used in pressure leach/oxidation processes. In order to simplify this non-linear mode of heat transfer, the effects of radiation had previously been incorporated in an equivalent convective film coefficient in finite element methods (FEM). This prior method omits the effects of radiosity, a critical aspect of radiation heat transfer, which affects the design of refractory lining systems in autoclave vessels. Given that 60% of the heat loss in actual plant practice of an autoclave is due to radiation, reliability in the FEM is therefore impacted. This study validates the use of radiosity in FEM through thermal loading using a combination of simple geometries to be applied to complex environments such as vessel nozzle clusters. The added benefits of using a radiosity load includes an increase in confidence in thermal distribution results, greater accuracy in determining appropriate refractory lining systems, weld overlay sizing, and increased accuracy in structural analysis.

Jan 1, 2014

By Ferri P. Hassani, Riadh Bouzaïene

"Selected methods of pressure loss predictions in horizontal slurry flow in pipelines are presented. For a given combination of flow velocity, solids concentration and particle size, the slurry and its flow conditions are described, and an appropriate method of pressure loss prediction is outlined. The wide range of conditions treated in this paper may be found in practice in areas varying from the hydraulic transport of low concentration slurries to dense-phase conveying of paste backfill in underground mines.IntroductionThe hydraulic conveying of solid particles in pipelines is a major component of the mining and mineral processing industry. Whether the objective is to transport ore to the processing plant or to make use of mill tailing as backfill material; the need for well designed, economical hydraulic conveying systems is recognized.The contribution of this paper is part of an on-going research program at McGill University involved in optimizing and developing techniques for total mine waste disposal. One of the main concerns in the conveying of solid-liquid mixtures is the prior knowledge of the pumping power input required. This energy requirement is directly proportional to the pressure losses incurred in the pipeline system. Understanding the sources of such pressure losses and predicting their magnitudes should enable the system designer to make informed decisions regarding the optimum mode of hydraulic transportation commensurate with the over-all requirements of the operation.This paper is an attempt to classify pressure loss prediction methods encountered in the literature for solid-liquid mixtures. In spite of the large number of publications spanning thirty years of research in the field of slurry transportation, it is sometimes difficult to correctly identify the appropriate methods applicable to a given situation. This is partly due to the inherent complexity of the mechanics of slurry flow and the ensuing uncertainty about the nature of the flow regime under investigation.Our approach is to use three fundamental parameters, namely: flow velocity, solids concentration and particle size (for solid particles with a given density) to characterize the slurry and the flow conditions, and to match them with an adequate pressure loss prediction method. For each combination of flow velocity, solids concentration and particle size, a description of the most likely prevalent flow conditions and some known methods of dealing with them will be presented. Qualitative definitions of ""high"" and ""low"" magnitudes of the aforementioned parameters will be given as a general guide to the classification scheme presented in this paper."

Jan 1, 1992

By G. Kollberg

"IntroductionThe SALA Caravan Mill system represents a proven concept for the design and operation of mobile and semi-mobile ore dressing plants.The Caravan Mill has been developed to meet the demand for a flexible processing plant to be used for small and medium-sized orebodies or for pilot investigations of deposits directly at the mine site e •The first Caravan Mill installation was put into operation in 1970 and a number of plants have been delivered world-wide since then.The Caravan Mill system has great flexibility both in capacity, ranging from 50 to 1000 tons per day, and in process combinations. The process modules available are:• crushing by jaw and cone crushers;• pre-concentration by the Dyna Whirl Pool dense media system;• grinding by wet rod or ball mills;• separation by gravity, magnetic, flotation or leaching-CVP adsorption methods;• dewatering by lamella or conventional thickeners and vacuum filters.To form complete plants, auxiliary equipment is also available, such as:• bins, feeders and conveying systems;• power generator units;• water tank and pump for process water;• interconnecting piping and cables;• erection and service tool kits;• set of spare and wear parts.For mine sites with rainy or winter conditions, a plastic tent with air heater can be supplied to cover the ore dressing equipment. Each module is workshop assembled complete with slurry pumps, internal pipe work, electric wiring with plug-in connections, hoses, etc., all arranged for quick and simple connection between the units. Before delivery, each unit is tested in the workshop."

Jan 1, 1982

By D. A. Trotter

"Low-pressure sodium light sources have been available for several years, but have not received wide acceptance in underground mining. This is because they are difficult to operate using DC power, they are not an intrinsically safe light where explosive gases may be encountered and they give poor colour rendition.With the need for energy conservation, several Canadian hard-rock metal mines are now changing their lighting to low pressure sodium, as it has the highest efficacy of any light source in terms of lumens per watt. Studies have pointed out several other advantages as well. Glare can be controlled, they penetrate fog well, they are easily maintained, they have a long life and they give the highest visual acuity when compared to other types of lighting. As well, in an underground mine, contrast is much more important than colour for task identification. For close work, the colour problem is alleviated with the use of cap lamps.Case studies are presented from Canadian practice. These show how the lights are modified for underground use, calculations preceding light installation, and how and where the lights are installed in the underground environment. Mention is made of worker reaction to the lights and possible physiological effects.IntroductionThe importance of good underground lighting to the total environment of mining cannot be overemphasized. In addition to the obvious benefits of improved worker morale, available studies show that good lighting practices reduce accident severity and frequency as well as increase production."

Jan 1, 1982

By J. G. Speight

Laboratory studies indicate that autogenous heating of low-rank coal can be prevented by a prior treatment which involves immersing the coal for short (5-15 min.) periods in an inert liquid at temperatures between ~ 350° and 400°C. Such "carbonization" effectively reduces the accessible pore volume of the coal to levels at which heat generation through subsequent sorption of moisture and oxygen is too slow to cause significant temperature rises in a stockpile. In addition, this treatment also irreversibly removes most of the moisture held in the raw coal and raises its calorific value by as much as 10-12%.

Jan 1, 1973

By R. G. Gillies, C. A. Shook, W. H. W. Husband

"The current state of knowledge concerning pipeline transport of coal in water slurry form is summarized for the four categories: coal-water fuels, conventional fine coal slurries, coarse coals and stabilized mixtures of coarse and fine particles. Surface chemistry is of dominant importance for coal-water fuels and considerable progress in understanding the role of surfactants has been achieved in recent years. Little generalized research on the flow of conventional fine coal slurries has been done in the past 17years, although innumerable conceptual designs and feasibility studies have been undertaken. Coarse coal slurries are fairly well understood but the model which explains their flow requires more data to be established fully. Stabilized flow mixtures should probably obey the same model as coarse coal slurries but experimental results for stabilized mixtures have not yet been incorporated in a comprehensive theory.IntroductionPipeline transportation of coal in a water vehicle has been employed for many years in coal washeries. It has been used less frequently in hydraulic mining and thermal power station fuel supply systems. The suitability of coal for pipeline transport arises from its moderate specific gravity relative to the carrier fluid and the fact that throughputs are often large and steady over long periods of time."

Jan 1, 1990

By C. D. M. Chisholm

Introduction The Sullivan orebody is a sulphide replacement deposit in beds of argillaceous quartzites. The general strike of the vein is north and south, with rather an abrupt change to northwest in the north limits, and a pronounced steepening of the dip in the same area. An east-west section across the orebody in the vicinity where the change in strike occurs will show the dip-to the east-to be about 10° to 20° above the 4500 level, 20° to 30° between the 4500 and 3900 levels, and 35° to 45° between the 3900 and 3500 levels. It is this last section, averaging 75 feet in thickness, that is being mined by the blast hole method discussed in this paper. Typically, the mineralization throughout this section follows the same general pattern between footwall and hanging-wall, there being solid sulphides for a width of 30 to 50 feet, above which lie quartzite beds of varying widths separated by ore bands which also vary in width and in grade. This banded part of the vein usually extends for 30 to 40 feet above the solid sulphides, with commercial ore terminating on reaching a siltstone bed. Development is generally carried to the highest ore band which, when averaged with the underlying quartzite band, will assay about the marginal limit in lead and zinc. When wide stopes are opened, sloughing to the siltstone usually occurs and, although the values are too low to carry the cost of developing and mining, the caved muck can be handled profitably with only haulage and treatment to be considered.

Jan 1, 1946

By Kai Zhang, Aijun Huang, Jeremy H. Rao, Xinhua Wu, Paul Rometsch

"As one of the most typical additive manufacturing (AM) technologies, selective laser melting (SLM) removes many of the shape restrictions that limit materials design, thereby allowing computationally optimised and high performance structures to be directly produced and tested. Due to the high reflectivity and lower absorptivity of Al alloy A357 powder during high temperature laser melting, one of the issues SLM might bring is the surface roughness and defects present on the parts. In this regard, this study investigates the surface roughness – fatigue property relationship for a heat-treated aluminium alloy A357 after SLM. Via the adjustment of SLM parameters, an ultrafine microstructure can be obtained due to the fast solidification rate. Therefore, comparable or even better mechanical properties can be achieved with respect to traditional A357 casting counterparts. Meanwhile, the surface roughness conditions of the SLMed Al alloy are also influenced by various processing parameters, raw powder properties, and sample building methods. For selective laser melted Al alloy A357 specimens, a dense part with a smoother surface would be expected to correspond with a good fatigue performance.INTRODUCTION Additive Manufacturing (AM), also known as 3D printing, is a process in which a complex part is fabricated layer by layer from a digital design package (Martin et al., 2017). AM has the potential to conserve raw materials, reduce the energy consumption, part cost, and fabrication time. Furthermore, as a typical additive manufacturing (AM) process, selective laser melting (SLM) was originally developed from selective laser sintering (SLS) based on higher quality lasers (Rao, Zhang, Fang, Chen, Wu, & Davies, 2017b). Different from conventional casting consuming valuable time and energy, SLM is now used as a cost effective method for the manufacturing of metals, such as Al-Si alloys, to produce almost full density parts using fine metallic powder and high power laser beam (Tang & Pistorius, 2017)."

Jan 1, 2018

By S. H. Seyedein

A mathematical model was developed to study fluid flow and solidification in a single-roll casting system. Fluid flow coupled with energy equations were solved numerically using a finite volume method. A body-fitted coordinate transformation technique was adopted to handle the irregularly shaped domain. In order to couple the continuity and momentum equations, a SIMPLEC algorithm was used. A fixed-grid enthalpy method was considered to model the solidification in the system. The turbulence effect on flow field was modeled using a low-Re k-e model The model developed in this work was further run under various conditions to optimize the operating parameters of the process.

Jan 1, 2004

By C. Blawert

In spite of various corrosion studies on HPDC AZ91, there is no clear indication which microstructure gives the best corrosion performance. The skin with its fine microstructure is sometimes reported to have the best corrosion resistance, but there is no clear definition of the skin. If the skin is the outermost part of the casting and nothing is removed from it, then it is contaminated and the corrosion resistance is low. If the outermost skin is removed (about 25 µm) then a better corrosion resistance can be obtained. However this does not automatically mean that there is no other region in the bulk of the casting which could have a similar or even better corrosion resistance. Indeed, the corrosion measurements including potentiodynamic polarization and long term electrochemical impedance spectroscopy (EIS) revealed a lower corrosion resistance of the original as-cast skin about 100 pm thick. The thickness of this region is more or less independent from the thickness of the casting section. The surface region is free from any dendritic grain growth which influences the amount and distribution of the 13-phase and therefore the distribution of the most important alloying element Al. This could explain the different corrosion behavior. Further reason can be found in the enrichment of some impurities such as Fe in the near surface.

Jan 1, 2006

By P. Mayer

"Determining the correct mechanism of a boiler tube failure is important for the prevention of future tube failures. Proper corrective measures can be undertaken to alleviate the root cause or causes for a failure only when the correct mechanism is known. A mechanism of boiler tube failure is defined as the process which degrades the tube and produces a failure.An expert system package was developed for use by electric utility power plant personnel during investigation into the cause of a boiler tube failure. It is intended to assist their efforts to recognize and identify a basic failure mechanism that can produce the type of boiler tube failure under investigation. The program guides the user to the most likely failure mechanism by asking simple questions, answers which can be obtained by determining the failure location, type of fuel, and from visual inspection of the failed tube. Expert systems are a form of artificial intelligence which imitate the decision-making process of experts.IntroductionBoiler tube failures (BTFs) continue to be the single largest source of forced outages in fossil fired electricity generating stations. Because of this a concentrated effort is being made to minimize boiler tube failure occurrences. Eliminating boiler tube failures could be worth $5 billion a year to the electric power industry(1).The aggressive service environment of fossil-fired boilers is largely the reason for these failures because the combined effects of stress, temperature, corrosion, erosion and vibration cause deterioration of boiler tube material properties and reduction in wall thickness.Determination of the boiler tube failure mechanism is important for the prevention of future problems. The root cause for a failure can be established and proper ameliorative measures taken only when the failure mechanism is identified correctly. The correct identification of failure mechanism is a complex process which may include many individuals and institutions. Technical specialists in metallurgy, chemistry, combustion, and boiler design frequently cooperate with the station staff in a failure investigation . These individuals rely on personal experience and numerous reports , theories, studies, private communications and investigations concerning the different failure modes and mechanisms."

Jan 1, 1990

By X. Cao, M. Xiao, M. Jahazi

Magnesium alloys have low hardness, wear, erosion and corrosion resistance. The repair of service-damaged aerospace components made of magnesium alloys is an attractive solution in terms of time and cost saving. The feasibility of applying laser beam technology to repair ZE41A-T5 magnesium alloy sand castings in the machined surface conditions was studied using a continuous wave 4 kW Nd:YAG laser system. The influence of process parameters such as laser power, cladding speed, wire feed rate and defocusing distance on the shape, size and area of single cladding beads is discussed using a process optimization software. Sound single clad beads with good geometric characteristics were obtained using strictly controlled laser process parameters. The overall results indicate that laser surface cladding using filler wire has the potential for repairing aerospace components made of cast magnesium alloys.

Jan 1, 2006