Search Documents

By Jorge Blanco, Joaquin Gotor, Enrique Delgado, Carlos Frias

Since 2009 Cobre las Cruces (CLC) has successfully operated a sustainable mining business near Seville, Spain, applying the most advanced hydrometallurgical technologies to process secondary copper sulphide ores through atmospheric leaching in ferric sulphate media and using oxygen sparging in a cascade of ten reactors. In comparison to conventional copper smelters, the CLC hydrometallurgical process does not generate SO2 gas, airborne emissions or slags. The copper ore is ground and sent directly to atmospheric leaching reactors; flotation is not required, and consequently, copper extraction is maximized at 93-95%, while producing 72,000 t/y copper cathodes of the highest purity (99.999 wt.% Cu, Grade A). Reserves for the CLC deposit were estimated at 16 million tonnes of ore averaging over 6 wt.% Cu and containing principally a chalcocite mineralization. Other copper bearing species include digenite, covellite, chalcopyrite, bornite and enargite. Pyrite represents over 70 wt.% of the ore. In the CLC leaching process, chalcocite reacts with ferric sulphate at approximately 90 ºC and copper is released into solution while ferric ions are reduced to ferrous ions. The ferric sulphate leachant is regenerated continuously by oxygen injection and consumes sulphuric acid. It is remarked that pyrite plays a crucial role to yield high copper leaching rates. When pyrite is oxidized, a small proportion of iron is co-leached and some sulphuric acid is generated. The CLC leaching technology has been designed to allow a certain level of pyrite oxidation, which is positive in many ways: (i) to maintain a Fe/Cu ratio in solution; (ii) to facilitate Fe(II) oxidation; (iii) to produce a high redox potential; and (iv) to counterbalance a bleed solution that removes some iron. Moreover, galvanic interaction between pyrite (cathode) and chalcocite (anode) can substantially increase atmospheric leaching kinetics and efficiency (copper recovery).

Jan 1, 2016

By L. V. Volkov

The equilibrium of the CuO-Cu20-Cu+-Cu2+ system with various chloride ion concentrations in solution in the presence or absence of an oxidant was investigated. It is shown, that, regardless of the presence or absence of chloride ions or oxidant (oxygen) in the system, the process can be divided into three stages, which are characterized by differing rates and mechanisms of metallic copper cementation and cuprite precipitation and, hence, lead to differing rates of the dissolution of nickel into solution. The effect of the concentrations of chloride ion and oxidant on the phases in the process residues is also discussed. The addition of an oxidant increases the amount of cuprite (Cu20) in the leach residue. With increasing chloride ion concentrations, the rate of copper cementation increases, even without an oxidant in solution. The results of these laboratory experiments and the mechanisms developed are consistent with analysis of samples of industrial cement copper obtained from the Severonickel Combine.

Jan 1, 2007

By Chao Yang, Liguo Tian, Yan Yang

"The Jinfeng gold mine is one of the three gold mines that Eldorado Gold has in China and it is the second largest gold mine in China. The mine is located in a relatively remote and mountainous area in the southwestern Guizhou province. The orebody is similar to the Carlin type deposit in Nevada. The mill throughput was designed to treat 3,600 tones per day. The ore comes from open pit mining and underground mining, and is fed to one-stage jaw crushing. The crushed ore is stockpiled, reclaimed and then fed to the SABC grinding circuit. After classification with hydrocylones, the ore is floated, and the resultant concentrate is oxidized biologically in a process known as BIOX®. The oxidized concentrate is then washed in a CCD circuit and finally leached with cyanide in a CIL circuit for gold extraction. Jinfeng produces about 180,000 oz of gold per year.This paper introduces operations and modifications of SABC circuit over the past three years, and then describes some technical characteristic of the SAG mill and other circuits in the processing plant.Major modifications and improvements on the SABC circuit are described in the paper, including:1. Impacts of grinding ball and mill liner with respect to material selection, quality, hardness, manufacturing methods, and interactions between mill liner and grinding ball.2. Effect of milling operation parameters on milling efficiency.3. Impacts of SAG mill scats and modifications of grate size to improve mill throughput.4. Design and construction of a pebble crushing system, and recycle the crushed scats to the SAG mill to improve mill throughput.With the above-mentioned modifications, 20% increase over the design in mill throughput has been realized over the past three years, and operating cost has been significantly reduced. However, some issues still remain, and thus process modifications and technical innovations are still needed."

Jan 1, 2012

By S. Sagar

In September 1996, Dofasco commissioned a 165 Mt twin shell EAF furnace and an associated ladle fleet. During and after this startup, refractory performance in the ladles was optimized on a holistic approach through several initiatives that increased ladle refractory retention times from 7000 to over 16000 mins (160 heats). This dropped the overall refractory costs by 40% while ensuring a consistent and predictable ladle performance. One initiative that drove enhancements was the proper brick selection for each particular refractory area and it's process conditions. The work concentrated on the selection of a resin bonded alumina magnesia carbon (AMC) brick in the barrel area of the ladle, upgrades to the 2 piece monolithic alumina cast ladle bottom and increasing the slagline refractory brick quality with the appropriate zoning/paneling. The adoption of a magnesia alumina carbon (MAC) brick in the transition area of the barrel/slagline has also improved performance and predictability. The design developments have lowered the overall wear rates and balanced the service life of the entire ladle. Safety was improved and breakout potential reduced by changing the safety lining from a high alumina brick to a state of art technology - monolithic shotcrete lining. This initiative decreased the overall manpower required to brick a ladle and increased shop ladle availability. The ladle bricking area environment was also improved by adopting a post combustion device to burn phenol fumes from ladle preheating practices. This has improved the overall health & safety of the reline teams. The consistent and predictable performance of the ladle on a whole has allowed the shop to decrease the number of working ladles in operation from 5 to 4. This further decreased wear rates from over-oxidation and excessive thermal cycling, saving approximately $500,000 in natural gas from pre-heater operations.

Jan 1, 2004

By V. Maazallahi, A. Rouleau, A. Saeidi

"The geometry of the terrain topography before and after the failure are the essential factors for analyzing a landslide and for the design of remedial works. This paper presents a method to determine these factors, considering that the determination of the slide surface profile is difficult and costly using traditional methods and the pre-slide topography data is often not available. The presented method to locate the 3-dimensional geometry of the slide surface is based upon determining the slide surface in 2- dimensional vertical sections. This method utilizes post-slide topography of the area to determine the pre-slide topography and uses equations to estimate the pre-slide situation using a statistical process applied to points located on the sliding mass. This method is tested on the Maskun landslide in Iran. The results indicate the applicability of the proposed method to obtain the key factors for the back analysis of a landslide in a cost effective manner.INTRODUCTIONProbably the most reliable method of determining the strength of soil and rock mass is to back analyze a failed or failing slope (Caia et al. 2007; Wyllie & Mah, 2004). This method is used in geotechnics for estimating geotechnical parameters of the rock and soil mass (Sakurai et al., 2003; Frayssines and Hantz, 2009; Cepuritis et al. 2010), but it requires that the failure mode is well established and that there is complete and precise information available on the slide surface and the sliding mass (Sjöberg, 1996). Measurement of the slope profile before failure provides the basic information required for a back analysis (Hock & Bray, 1981). The post-slide topography is another key factor. The back analysis process for determining the actual strength parameters of soil or a decomposed rock mass after a landslide requires knowledge of the sliding mass geometry, both before and after the sliding event. Many studies are reported in the literature about the application of back analysis for determining geotechnical and geomechanical parameters of rock and soil mass (Sakurai et al., 2003; Cepuritis et al. 2010; Frayssines and Hantz, 2009, Hussain and Stark, 2011), but they generally present little information about the geometry of the slide surface, and the weight of rock and soil mass that slid, although these factors are the most important parameters for back analysis process. Liang and Xue-song (2012) determined the slip surface having the minimum factor of safety (called critical slip surface in deterministic analysis of slopes) and the slip surface with the minimum reliability index (called critical reliability slip surface), but they have not considered the actual profile and geometry of the slide surface. Rocscience (2013) proposes the back analysis option in the Slide software for slope stability study, but it requires an imposed slide surface as input; alternatively, one can estimate by a finite element analysis the surface with the minimum factor of safety. However, this estimated surface is very likely different from the actual sliding surface, considering the uncertainties in input data of the finite element method."

Jan 1, 2015

By M. Tadie, J. Wiese, K. Corin

The use of potential control in the flotation of ores has been applied in a variety of operations and presents an opportunity for improvement of selectivity and recovery of valuable minerals. Although it is possible to vary the redox potential (Eh) using chemical additives such as sodium hypochlorite or hydrogen peroxide this is more commonly done by varying the pH and dissolved oxygen (DO) concentration. The present study involves an investigation into the effect of varying dissolved oxygen concentration, ionic strength (IS) and pH on the flotation response with the aim of application to a South African lead-zinc ore. In all cases the Eh is measured as a function of the different DO, IS and pH values. The main objective was to achieve selective flotation of galena from sphalerite. The first part of the work was micro-flotation tests conducted on single minerals with galena used as the basis for effect of the factors studied on redox potential and ultimately recovery. The DO was varied by alternating between the use of air and nitrogen as the gas source to the micro-flotation cell. PH was varied between pH 9.2 and pH 11.8 using sodium hydroxide. In the first part of this study a factorial design approach was used to determine the interactive effects of the variables tested, viz. DO, ionic strength and pH, on the Eh and on the recovery. Redox potential was measured using a combination electrode made up of platinum wire and Ag/AgCl reference combination. Recoveries indicated that pH had the most significant effect on recovery and Eh. The influence of redox potential on recovery was found to be of relevance to the condition of high dissolved oxygen concentration and less so at low dissolved oxygen concentrations. It was also noted that that the combined interaction between ionic strength and dissolved oxygen concentration had a positive effect on recoveries, however this was not so with Eh. The chemistry of the ions in solution was observed to play a dominant role on the recovery due to changes in solubility arising to pH modification. The longer term objective of this work is to determine the optimal Eh conditions for the separation of galena from sphalerite.

Jan 1, 2016

By L. Beiza, L. Velásquez-Yévenes

Chalcopyrite is by far the most abundant copper sulphide on Earth, but it has proved to be problematic in its processing by leaching, mainly related to its refractory nature, slow kinetic rates of dissolution and the formation of an inhibiting product layer on its surface during leaching. This study is focussed on the electrochemistry of chalcopyrite dissolution in acidic chloride system, which has recently gained attention as a feasible alternative to conventional sulphate media for chalcopyrite leaching. It is well understood that chalcopyrite dissolution from mineral grains depends strongly on the solution redox potential at the mineral surface as well as the composition of the product layer that may form on its surface. The chloride ions in solution support the Cu(II)/Cu(I) couple as the primary oxidant, as they can form complexes with the cuprous ions formed, increasing the dissolution rate. Additionally, these ions increase the potential range where chalcopyrite can be oxidized. The chemical reaction that occurs on the surface of chalcopyrite in chloride solutions in the presence of cupric ions will be characterized and the coulometry of the reaction will be reported to understand what is happening on the surface of chalcopyrite. Electrochemical experiments have been carried out to investigate the behaviour of mixed potential by open circuit potential (OCP) measurement for 30 minutes using sulphuric acid at pH 1 under nitrogen at 25⁰ C. The effect of chloride was analysed at 0, 20, 50 and 100 g/L and cupric ions from 0 to 50 g/L. The potentials obtained were then used to carry out chronoamperometry tests for a period of 30 minutes in absence of cupric ions. The mixed potential did not show a significant difference with an increase in cupric concentrations in the absence of chloride. Increased mixed potentials and current densities were observed at higher chloride and cupric concentrations. Chronoamperometry tests at those potentials were used to construct a voltammogram trace which has the same trend as a normal cyclic voltammogram but with much lower current densities. INTRODUCTION As a result of the depletion of copper oxides, the leaching of copper sulphide minerals has become the focus of many studies. Chalcopyrite, (CuFeS2) which is the most abundant of copper minerals, has proved to be challenging to process via hydrometallurgy, mainly related to its refractory nature, slow kinetic rates of dissolution and the formation of an inhibiting product layer on its surface, during leaching.

Jan 1, 2019

By G. Sedelnikova, D. Kim, N. Ibragimova

"The object of this study was three samples of sulfide old tailings, which were obtained after Cu- Zn ores processing. Fine metal dissemination in sulfides as well as fine mineral intergrowth determine the refractory nature of material and low metal extraction using simple methods: gravitation 1-6%, flotation 32-48%, cyanidation 10-37%, and cause the need to use sulfide bio-oxidation to liberate gold and to recover it by heap leaching. The gold is the main valuable metal in the tailings with content 1-1.5 g/t. Heap bio-oxidation with mesophilic and moderately thermophilic bacteria was used for pre-treatment of tailings before gold heap leaching from bio-oxidation solid residues. The tailings have a low permeability < 0.3-1.2 m/day, which is caused by migration of fine particles, decreases recovery rates, and is poorly suited to heap bacterial leaching. Therefore, preliminary gold sulfide tailings with permeability < 0.3 m/day were pelletized using copper containing flotation tailings of converter slags and calcium oxide. The most gold extraction was obtained for pelletized tailings. The base metals (copper and zinc) were precipitated from bacterial solutions. Experiments have demonstrated effective bio-oxidation of all third gold sulfide tailings samples and enough high gold extraction 60-82%.INTRODUCTIONIn Russia, as everywhere, there is a trend toward deterioration in the quality of mineral resources, including non-ferrous and precious metals, manifested in lower grade and higher complexity of ores. The proportion of refractory ores is increasing, characterized by fine dissemination of metals in sulfides, intergrowth, and poor liberation of minerals during concentration, resulting in loss of base and precious metals to flotation tailings.Over the operation period, huge reserves (hundreds of million tons) of ore processing waste have been accumulated at mining and concentration operations. Because of the imperfections of the previously used ore concentration technologies, the content of precious and base metals in flotation tailings is comparable with the grades of the ores being currently processed. Therefore, old tailings can be viewed as an additional reserve of non-ferrous and precious metals. The works (DEN, 1997; Lyman, Johnson, & Guerney, 2000) demonstrate that, tailings containing sulfides (sulfur, copper, zinc, and other metals) are a potential environmental hazard since they produce acid drainage water containing toxic components. Processing those tailings would require designing an effective technology for recovering useful components and protecting the environment."

Jan 1, 2016

By R. P. Viljoen, A. L. Sokolov

"The distribution of mineralized provinces is analyzed on the basis of their genetic link with specific blocks of the earth&apos;s crust including ancient platforms, mobile belts and zones of tectonicmagmatic activation. Mobile and fold belts surround the Siberian platform in Russia and the Kaapvaal craton in South Africa, with decreasing age zoning away from ancient platform margins. The main differences in the geological development of the two cratonic areas are: (1) the long period before the final stabilization of the Siberian platform (3600 Ma to 1600 Ma) and the comparatively short period of time for the stabilization of the Kaapvaal craton (3600 Ma to 3050 Ma) and (2) the intensive multiple activation of the marginal zones of the Siberian platform and the tectonicallycontrolled, magmatic sedimentary, intracratonic activity, typical of the Kaapvaal craton. Mineralization of the Siberian platform is largely characterized by marginal reactivation zones of differing ages although mineralized intracratonic Cu-bearing basins of Proterozoic age are also known. Mineralization of the Kaapvaal craton is mainly related to the formation of the intracratonic basins i.e., Witwatersrand (Au, U) and Transvaal (Au). The latter is characterized by multi-age volcanic-intrusive activity including the emplacement of Bushveld Complex (Cu, Ni, Pt, Cr, Au, V). The Siberian platform is characterized by the prolonged development of inherited mineralization from Archean until the late Mesozoic. The main period of mineralization in the Kaapvaal craton is restricted to the middle Proterozoic.The Baykal-Patomskaya and Namaqua-Natal mobile zones occupy similar positions adjacent to the Siberian and Kaapvaal cratons, respectively, and demonstrate similar modes of metallogenic development: i.e., the early formation of exhalative Pb-Zn-Cu deposits during the early stage and magmatic Cu deposits during the late stage. The more remote mobile belt near the Siberian platform, the Trans-Baykal, is characterized by intensive multi-age mineralization (Wo, Mo, Sn, fluorite), related to a period of tectonic-magmatic activation. The Saldania Belt occupies a similar position near the Kaapvaal craton but is known for its poor Au, and Cu mineralization. It does, however, have some similarities with Trans-Baykal Belt in regard to Mo-W bearing granitoids.The phenomenon of interference of geosynclinal, orogenic, platform, and tectono-magmatic activation regimes is known for the Russian section of the Pacific Ocean Volcanic Belt."

Jan 1, 1994

By H. H. Wober, P. J. Morgan

"The proposed classification of ore reserves based on geostatistical and economic parameters is designed to be used as a communication tool to identify for investors, bankers, and financial analysts the degree of risk associated with a specific class of ore reserves. The class designation identifies the degree of accuracy of the estimates for tonnage and grade of annual production volumes of ore. It thus enables decision makers to quantify the risks and uncertainties inherent to the ore reserve in achieving over-all economic goals and annual financial objectives.IntroductionDuring the evaluation, in 1980, of the Creede silver deposit in Colorado, U.S.A., as a potential bulk mining project, the authors were faced with the problem of conveying to senior management the risks and uncertainties that are implied by using common or conventional classification systems to categorize ""ore reserves"". The estimated numbers for tonnages and grade of the projected ore reserves represented the only entry for future revenue from the project. It was, therefore, necessary to convey to management the level of risk associated with those numbers when implementing further stages of development, and to convey what impact significant differences would have on the profitability of the project. The desire to quantify these risks led to a revised definition of ""ore"" and to a re-examination of the classification system of ""ore reserves"". Traditional methods for estimating tonnage and grade of reserves do not include a quantification of the errors of these estimates. The advent of geostatistical methods made this quantification possible. The proper application of geostatistical methods, with adequate geological input and a reliable set of sample data, is essential to its validity.Others have proposed a classification of ore reserves based on geostatistical parameters. Diehl and David (1982) recognized ""that concepts of proven, probable and possible have to be linked to the production rate or time horizon"". Royle (1977) had also addressed this problem. Forsyth (1987) pointed out that bankers are concerned with ""the probability that the variability will fall within a certain degree of accuracy"" especially for grade estimates, and would like to see grades expressed together with the error of the estimate at the 950Jo confidence level."

Jan 1, 1993

By M. Fainerman-Melnikova

The use of strong base ion exchange resins for the extraction of uranium was pioneered in the 1950?s. Ion exchange technology is applicable to dilute leach solutions such as those obtained from in-situ, heap leaching or in-plant processing of low grade ores. A further advantage of ion exchange processes is that fluidised bed technology allows for treatment of solutions with a relatively high concentration of suspended solids and resin-in-pulp technology can treat leach slurries. However, the extraction of uranium with strong base resins is severely affected by the presence of chloride ions in solution. In areas where high quality water is not readily available, the use of saline water as process water would extend the potential application for ion exchange in uranium processing. Our research program has studied the effectiveness of a wide range of commercially available ion exchangers in uranium extraction from saline solutions. In the present work, we examine the impact of salinity (ranging from chloride concentrations found in groundwater to those present in sea water), on the uranium extraction with weak base anionic resins (WBA). The effect of pH and the presence of the competing impurities are also discussed.

Aug 1, 2010

By Q. Ricoux, F. Goettmann, A. Maihatchi

"Electrodeposition processes are widely used in the metallurgical industry to produce, extract and refine metals from various feed materials. However, raw materials used to provide non-ferrous metals often contain high amounts of iron. In the presence of iron, while metals are plated at the cathode, electrowinning processes produce corrosive and highly oxidative ferric ions at the anode that are harmful for the process sustainability. In fact, these ferric ions cause dramatic current efficiency loss, induce high maintenance expenditures to limit the corrosion of devices and it results in the formation of impure and dendritic deposits on the cathode. Consequently, the management of iron in electrodeposition process became a major issue in non-ferrous metals production. Actually, numerous methods have been developed to limit the ferric ion concentration in the electrolyte or, at least, to limit its harmful effect. Many methods aim to limit the iron(III) concentration in the electrolyte, generally by coupling electrowinning to extraction process such as solvent extraction (SX) (Bender & Emmerich, 2015), ion exchange (IX) (Gula, Dreisinger, & Horwitz, 1996) or cementation (Kust, 1979) processes to remove ferric ions. Other routes consist of (i) using the ferric ions oxidant properties to leach raw materials, either directly in the electrolytic cell (Fanta & Tributsch, 1975) or through a secondary circuit (Cain, 1950), or (ii) reducing ferric ions through periodic reversal of direct current to enhance the formation of Fe2+ (Loutfy & Bharucha, 1980). On the other side of the spectrum, papers discuss methods to valorize the iron from by-products of the non-ferrous metal industry, that generates vast quantities of iron containing wastes (A. Agrawal, Sahu, & Pandey, 2004). Many studies on iron electroplating and electrolytic iron production from ores have been carried out (Cain, 1950; Mostad, Rolseth, & Thonstad, 2008), but very few have been conducted on waste or by-products. Therefore, we propose to build on the previous literature review to develop a process for the production of electrolytic iron from by-products.INTRODUCTIONNon-ferrous metals and their alloys are used in a large variety of applications. Aluminum and titanium are used for their strength, light weight and corrosion resistant properties in structural applications. Copper has been used in various applications requiring high thermal and electrical conductivity, as kitchen products and electrical wires. Nickel and zinc are commonly used as plating materials; nickel offers a wide range of working temperature and zinc is used for steel plating. Gold, silver, and platinum group metals are used in electrical/electronic applications, jewelry and chemistry as catalysts."

Jan 1, 2016

By Frank Ebbutt

Introduction The property of the Britannia Mining and Smelting Company, Limited, is situated on the east side of Howe sound, about six miles from its head. It is roughly thirty miles by water from Vancouver, one of the important ports of the Pacific and the industrial and financial centre of British Columbia. Howe sound is navigable for ocean-going vessels and Britannia Beach is a daily port of call for the commodious boats of the Union Steam-ship Company, sailing from Vancouver. Few mines are so ideally situated or have so many or varied natural advantages. Copper was first found on Britannia mountain in 1888, by Forbes, but it was not until 1898 that five claims were staked here by Oliver Furry, a trapper. It is from these claims that the major production during the past thirty years has come. In 1900 the Britannia Copper Syndicate was formed and development of the property was commenced. In 1903 the late Grant B. Schley obtained control, and through his efforts the Britannia Mining and Smelting Company was organized in 1908 as a subsidiary of the Howe Sound Company. Since that time, a persistent and progressive policy has been followed, which has resulted in a prolonged and profitable operation. The country in the immediate vicinity of the mine is marked by strong relief, with mountains rising abruptly from tide-water to elevations of 5,000 feet and more. Two broad transverse valleys deeply dissect the area. These are the valleys of Britannia creek and Furry creek. The region has under-gone prolonged and relatively recent glaciation. Over much of the surface there is deep overburden and dense vegetation. The geology of the mine and vicinity has been described in reports by S. J. Schofield (1), H. T. James (2), J. G. Barry, and others (3). The present writer is in accord with much of this literature on Britannia, but during recent years, extended observations made underground have shown that the &apos;quartz porphyry&apos;, or &apos;mine porphyry&apos;, of several of the earlier writers is not the host rock to the commercial mineralization; and he contends that the mineralization occurs in highly altered phases of a complex series of ruffs, flows, and pyroclastics and their autoclastic metamorphosed products.

Jan 1, 1935

By A. Singh

"The flotation of fine minerals less than 10 µm in size is an age old challenge spanning both the precious metal and industrial mineral sectors across a range of commodities. This problem has been brought into sharper focus by the emergence of the practice of fine grinding of flotation feed to effect better liberation of the targeted minerals. However, the ability of conventional flotation cells to effectively float the liberated fines remains questionable. In order to overcome this problem, Gold Ore postulates the “Bringing the Mountain to Mohamed” hypothesis which comprises the steps of gas nucleation on particle surfaces, aggregation of particles and levitation of aggregates. Testing of this hypothesis at Mintek, South Africa, showed a ~180% increase in the Kelsall kfast factor coupled with a projected recovery improvement of ~4 % for the Mach Reactor case coupled with a final concentrate grade of ~2 times that of conventional flotation. These fundamentals were then extrapolated to plant scale with Mach Reactors installed on the flotation feed at Platmin’s Tailings Scavenger Plant (TSP) with the objective of scavenging the fine minerals lost to tailings by the main plant. This paper details the theory, pilot plant results as well as key aspects of the full scale plant design supplemented by operational plant observations after commissioning. This game changing application is regarded as being pivotal to future flotation plant design whilst providing the technology leverage required for the survival of mineral operations in an economically unfriendly environment.INTRODUCTION - THE CONUNDRUM OF FINE PARTICLE FLOTATION“If the mountain won't come to Mohamed then Mohamed must go to the mountain” is an age old saying written into the book of proverbs in 1670. Legend has it that Mohamed promised his people that he would summon a mountain to come over to him so that he could offer up his prayers from its summit. After numerous attempts at moving the mountain went in vain, Mohamed, quite unabashed, said “Well if the mountain will not come to Mohamed, then Mohamed will go to the Mountain.” In this analogy, Mohamed is a fine particle <10 µm and the mountain is a bubble within a flotation system. The age old challenge is how to bring these two together to achieve attachment?"

Jan 1, 2016

By Daniel Hodouin, Mélanie Proulx, Claude Bazin

"Collector and frother are commonly used to induce the floatability of valuable minerals in flotation plants. These reagents are usually distributed down a flotation bank or sometimes added in a single location at the top of the bank. A review of the literature and some experimental results obtained from laboratory and full scale trials indicate that the way flotation reagents are distributed down a flotation bank may influence the flotation response of coarse particles. The paper summarizes these observations which show that the distribution of reagents is a potential tuning variable for process optimization.IntroductionFlotation is in many cases the only way to concentrate sulphide and some oxide minerals. Flotation is a concentration process that uses particle surface composition to induce the selectivity by mean of hydrophobic reagents. The influence of particle size on flotation was firstly analyzed in the 50's1·2 and intensively investigated in the 70's, early 80's and 90's3-18. Most of the observed results show the existence of an optimum flotation size range9 whose recovery is not significantly influenced by a reduction of collector dosage""18. This result brought the idea of using a small portion of the total collector dosage at the top of a rougher bank and to distribute the remaining through the end of the bank to ensure sufficient collection of the coarse particles that need more hydrophobic coverage to attach to air bubbles and be lifted to the surface.This paper discusses the idea of using the distribution of reagents down a flotation bank to tune the operation of the process. Unlike the literature on the effect of reagents (collectors, frother...) dosage that is dense, little attention has been put on the distribution of reagents in a flotation bank. Although research on this subject has not been pushed very far, some operators have recognized the potential of a strategic addition of reagents down a flotation bank19. Except for a few exceptions, the proportions of the reagents to be distributed down a flotation bank are decided according to operator's experience instead of process analysis in relationships with particle size. This paper recalls observations made by different researchers that lead to the idea of using the distribution of reagents as a tuning variable for the flotation process. The paper does not present a detailed analysis or optimization scheme for tuning the distribution of reagents, but analyzes some plant and laboratory results with a view toward the development of a testing methodology and ultimately a validation or rejection of the idea."

Jan 1, 1998

By George C. Riley

While the general public has little knowledge or appreciation of either the mining or explosives industries, modern civilization could not exist without them. They are to-day the key industries of the world. In common with many other industries the demands of the war greatly stimulated the production of explosives and the research necessary for such increased production. Production, supplies of all kinds, munitions of all sorts and then again production, practically regardless of cost, were the first reactions to the imperative war demands of the governments of the world. Following the war there was a momentary lull, then first gradually but with quickening acceleration, particularly in a recent slump, the situation was reversed - cost and not production was the dominant factor. Some industries readjusted themselves very rapidly and completely. Others were but partially re-adjusted and others again only carried out the process of deflation in certain departments. The explosives industry in Canada has not only thoroughly deflated itself, but has learned to apply to commercial disruptive explosives, the best, most efficient and most economical methods of manufacturing developed during the war. As a consequence, miners have at their disposal to-day better and more different kinds of compressed energy than ever before in all the long history of mining.

Jan 1, 1925

By J. B. Evans

"THE OPPORTUNITY to participate in a CIM seminarconcerning the direction of mining engineer trainingis perhaps fortuitous as it comes at a time when theengineering schools which have invited inspection byCanadian Accreditation Board of the Canadian Councilof Professional Engineers are examining theirrespective curricula.Currently there exists considerable soul-searching in various engineering schools across Canada where questions such as the following are being posed.- Have we achieved the correct balance between subjects related to technical methodology and subjects devoted to conceptual planning and design?- Should we include ""applied humanities"" in our program? (Whatever ""applied humanities"" might mean!)- Should courses covering pollution control, ecology, economics, technical writing, professional conduct and ethics be offered as compulsory subjects, as electives, or not at all?- Is it a better scheme to have students complete an Arts or Science degree before entering engineering?- Do we place too much emphasis on pure mathematics and sciences with the result that insufficient time is available for instruction in the engineering applications of these subjects?- Should English expression and/ or literature be included in the engineering programs and, if so, should these subjects be presented by the English department or by English lecturers captive to the engineering school? - Is the present program directed primarily at research activities rather than preparing engineers for their future roles in industry? - Should we teach our own versions of mathematics and physics? - Do we have sufficient engineers on the faculty strength or are we overloaded with Ph.D.'s from the pure sciences? - How flexible should the program be, what should the compulsory vs elective course content be, and what freedom of choice, if any, should be given with respect to elective courses? - To what extent should students contribute to faculty decisions?- How far should we pursue computer science subjects and do we need to make our students proficient in computer programming? - How far should operations research and mathematical models be carried in the undergraduate program when the students have limited experience in the real engineering world? - Realizing that an engineer never completes his education, should the undergraduate program cover ""bare bones"" engineering and should instruction in particular disciplines be left to graduate schools and / or industry?"

Jan 1, 1972

By J. P. Messervey

As a result of my field examinations in this Province, I have been struck by the evidence of widespread mineralization in rocks, particularly the limestones of Carboniferous age. Six prospects of lead and zinc or lead alone scattered through the eastern part of the mainland, one copper prospect and three veins of siderite, all point to a period of mineralization subsequent to the forming of the Carboniferous rocks in which they occur. While none of the present prospects are of proved economic importance, still it is possible, and indeed probable, that further prospecting will find concentrations sufficiently large to make mines. It may possibly aid the prospecting for these base metals if the present scraps of information are assembled from various sources, and I will further briefly recount the information as a result of my observations. Gay?s River At Gay&apos;s river, midway between Halifax and Truro, and four miles east of the railway, numerous pits and natural exposures show galena and sphalerite in limestone of Carboniferous age, near where it lies unconformably upon slate and quartzite of the gold series. These exposures extend for a length of over one thousand feet along a curving contact. The pits show that on the contact there is a fossiliferous and somewhat porous layer of limestone, which is so impregnated with galena and small amounts of sphalerite as to be of ore grade. Wherever observed, the thickness of this layer is less than two feet.

Jan 1, 1929

By D. A. McIsaac

In these days, when mass production seems to be the watchword of all industrial companies, nothing is left undone to attain this end. Transportation, where necessary, becomes a question of very great importance. For this reason every mechanical contrivance known to man is employed, with its resultant advantages. So successful has man&apos;s ingenuity been that, offhand, we are inclined to say that practically all transportation ?On a large scale is done mechanically, that is, where speed and economy are desiderata. Granting this, one would think that to read a paper on the horse before your honourable and highly technical Society would surely be a waste of time, and that any Company employing old-fashioned &apos;horse&apos; power would certainly be very much behind the time, to say the least. However, the fact remains that the biggest industry in our country today-coal mining-must use horse power to a great extent, being compelled both by considerations of economy and by necessity. For this reason,&apos; in the production of coal under present conditions, the pit horse is of great importance to this industry and is to be considered seriously as one of the units that help to make coal mining a success or a failure. Hence, in employing horses as a power for transportation, care must be exercised in selecting the animals, and the care of this power must be considered as seriously as any other department of such an organization. In selecting a pit horse, several things must be borne in mind, that is, one must get as much horse power as possible in as compact a form is practicable. This determines the type of horse we must use, which is of very great importance under our present conditions of coal mining. With low roof, steep grades, and forced production, a distinct type of animal must be selected.

Jan 1, 1930

By Mariam Melashvili, Chris Fleming, Rene Jackman

"A study was undertaken to develop a flowsheet for treating a high grade silver/gold ore body by cyanidation, CCD and Merrill Crowe precipitation, with tailings detoxification to meet stringent limits for cyanide and thiocyanate concentrations in the final discharge. In one of the flowsheets examined, free cyanide in the final leach liquor was recycled to the mill where it was hoped that it might react beneficially with fresh ore to reduce the cyanide makeup by an equivalent amount. However, laboratory results suggested that most of the cyanide recycled to the mill reacted with iron forming a soluble ferrocyanide complex. This would have had a negative impact on cost, not only because the cyanide recycled to the mill could not be claimed as a credit, but also because the presence of ferrocyanide in the final tailings meant copper sulphate had to be added to the SO2/air cyanide detoxification process to precipitate the iron cyanide. In an alternative flowsheet that was examined, recycling of cyanide to the mill was abandoned, and this allowed the milled slurry to be pre-aerated in a single mixing tank before cyanidation. During alkaline pre-aeration, any ferrous ions that are generated in the mill are oxidized to ferric ions, which, unlike ferrous ions, are inert in cyanide solution. This significantly reduced cyanide consumption and lowered costs in the detoxification of the tailings. In this paper, the cost implication of these two circuits is compared.INTRODUCTIONMost of the gold that is produced by hydrometallurgical processes is recovered by cyanide leaching. The reason for that lies in the superior thermodynamic stability of the gold cyanide complex and the favorable economics this confers on the process (Fleming, 2014). However, the gold in most of the gold-bearing ores processed is a very minor component, and therefore, the leaching response is often dominated by that of the host minerals.Many gold ores treated by the cyanidation process contain iron minerals. Cyanide reacts readily with some iron minerals forming ferrocyanide as one of the compounds. Ferrocyanide is stable when solutions are exposed to air and does not retard the dissolution of gold. In fact, it has been claimed that potassium ferrocyanide in the presence of oxygen is a weak solvent for gold (Hedley & Tabachnick, 1958). The main problem with the formation of this compound is the consumption of cyanide. Ferrocyanide contains six molecules of cyanide for each atom of iron {Fe(CN)64-} so the wasteful consumption of cyanide is greatly increased by its presence. Thiocyanate is also often produced during the reaction of certain iron sulphide minerals with cyanide, and contributes to the wasteful consumption of cyanide. In addition, environmental regulations in certain countries demand that thiocyanate be removed from the tailings, and this adds significantly to the cost of tailings treatment."

Jan 1, 2016