Search Documents

By R. V. Typliski, G. J. Labarre

"Hudson Bay Mining and Smelting Co., Limited, Flin Flon, Manitoba, has developed a metallurgical wastewater treatment system employing two-stage lime neutralization, sludge recirculation and conventional mechanical thickening.Laboratory investigations, initiated in 1970, led to the construction of a pilot-scale minewater treatment plant, at Schist Lake Mine, in early 1971. This plant, treating 600 cubic metres /day of wastewater containing 30-60 mg/1 zinc. demonstrated metal extraction efficiencies of 99% under normal operating conditions.On the basis of this pilot work, a second pilot-scale treatment system was established in 1975 at the Flin Flon metallurgical plant to treat zinc refinery process waste water. Through numerous improvements, including automatic con¬trol equipment, the system has evolved to a full-scale operation capable of treating 800 cubic metres/day of wastewater containing 4-11 gm/1 zinc. Treated effluent contains 0.2-20 mg/1 zinc. The hydroxide sludge produced returns to the metallurgical process for the recovery of metals while clarified effluent discharges to waste.With the system, Hudson Bay Mining has achieved its original goal: the reduction of environmental contamination, while realizing a return from metal recovery.IntroductionWith the goal of reducing environmental contamination, Hudson Bay Mining and Smelting began laboratory testwork, during the late 1960's, into the methods and technology for neutralizing and removing heavy metals from acid mine drainage. Based on lime treatment, early tests showed much promise and culminated in the construction of a pilot-scale test plant at Schist Lake Mine in early 1971.This pilot system utilized technology developed in laboratory studies, and related to work then underway by state authorities in Pennsylvania coal mines. The basic operation consisted of a lime slurry tank, baffle reactor and a free-settling basin. Through three summers of operation, the Schist plant, capable of treating 600 cubic metres/day of minewater, produced a heavy-metal extraction of 99% under normal conditions. Although successful in proving the treatment chemistry, the plant displayed deficiencies in sludge densification and handling."

Jan 1, 1980

By M. E. Sirkka

"INTRODUCTIONInco Ltd. has ten operating mines in the Sudbury district. Over the last ten years mining methods have changed at Inco with special emphasis on the introduction of bulk mining replacing conventional mechanized cut-and-f ill and undercut-and-fill methods. At the same time, the technology and size of LH D equipment has also progressed to meet the demands of bulk mining. This paper will concentrate on various aspects of the introduction and operation of electric LHD equipment a t Inco Limited, Ontario Division. BackgroundInco Limited received its first electric 2 cu. yd capacity LHD in July 1975 at Creighton Mine. The unit was tested pulling shrinkage stope muck and then was moved to a mechanized cut and- fill complex on 6600 Level. The electric scooptram received quick acceptance from the operators, due to its quiet operation and low heat generation, in a relatively hot operating environment. Although there are only two of these units operating a t present, this initial favourable experience, both in cost and efficiency, led to the development and purchase of electric scooptrams of the 5 cu. yd size. There are currently eleven 5 cu . yd electric LHDs in operation.The most recent development a t Inco is the move to yet larger electric LHDs in the 8 cu. yd size. The first electric ""Eight"" has now been in operation at Copper Cliff South Mine for over a year. This unit has the distinction of being the first one of its kind in service in North America. At the time of writing, there were ten 8 cu. yd electric ma chines operating in Inco's Ontario Division Mines, with three on order."

Jan 1, 1989

By Jun Shan

The preparation of poly(N-isopropylacrylamide)-monolayer-protected clusters (PNIPAM-MPC) of gold nanoparticles was carried out in a homogeneous phase using three ways, in which three types of PNIPAM ligands were employed. The first type comprised of PNIPAMs with narrow molar mass distributions, synthesized by reversible addition-fragmentation chain transfer (RAFT) polymerization and thus, bearing a dithiobenzoate at the chain end. These polymers were used directly to passivate the gold nanoparticles upon the Schiffrin reaction in a one-pot synthesis. The second type of ligands was derived from the first one through hydrazinolysis, and they therefore contained a thiol end group. The third type of ligands was PNIPAMs obtained through conventional radical polymerization, post-modified to contain thiol end groups. The PNIPAM-MPCs were characterized by high-resolution transmission electron microscopy, and by dynamic light scattering. The one-pot synthesis utilizing the ligands of the first type turned out to be a simple and facile method, compared with the other two ways, with which the size of the gold nanoparticles can be easily manipulated mainly by adjusting the molar ratios of PNIPAM / HAuCl4. PNIPAM is a more efficient ligand to stabilize the gold nanoparticles in water and in organic solvents than alkanethiols. The surface density of PNIPAM chains ranged from 1.8 to 3.6 chain/nm2, which is much lower than that typical for alkanethiols. The thickness of a PNIPAM monolayer bound to the gold core is somewhat larger than the size of the random coil of corresponding free PNIPAM in aqueous solution, which suggests that the conformation of a PNIPAM chain bound to the gold core is to extended.

Oct 1, 2003

By G. W. H. Norman

"The Indian Molybdenum deposit occurs in granite near the centre of Indian peninsula, Kewagama lake, in Preissac township, Abitibi county, Quebec, about 40 miles east of Noranda. Quartz veins containing molybdenite were discovered in the vicinity of the deposit in 1901 by J. F. E. Johnston of the Geological Survey of Canada. Innumerable trenches and a few pits were excavated during and prior to the first great war, but there was no production. During the second great war systematic drilling along a favourable zone disclosed by the earlier trenching outlined an orebody of 225,000 tons with a molybdenite content of 0.46 per cent.A 500 on mill was built in 1943, and 91,489 tons of ore underwent treatment, from which 699,568 lb . of molybdenite was recovered. The mill closed down early in 1944 when the wartime need for Canadian molybdenum production eased .GEOLOGYThe general geology in the vicinity of the deposit is shown in Fig. 1. The deposit lies at the north edge of a muscovite-biotite granite mass about 2 miles wide and several miles long. West of Kewagama lake this granite is cut by great swarms of quartz veins . The only other granite in the district known to contain similar swarms of quartz veins, and which similarly has become a source of mo!ybdenite, occurs 20 miles east in La Corne township. The non-molybdenite-bearing granites of the district are either more basic and contain frw dykes except aplite or are distinctly pegmatitic types and contain up to 50 per cent pegmatite dykes with molybdenite only here and there in small amount."

Jan 1, 1954

By S. H. Lucas

"This paper describes the development and application of single-stage fluidized bed continuous ion exchange to the following processes: removal of base metals from mine water; cyanide removal from gold mill waste; uranium removal from sulphuric acid leach liquor; and uranium removal from mine water. IntroductionThe recovery of metals by fixed bed ion exchange has been practiced for many years. However, the operation has been semi-continuous and can only treat clarified liquors. Substantial savings could be made if the operation were continuous, thus reducing the resin inventory, and if the costly filtration and clarification steps could be eliminated. Work has been in progress over the past twenty-five years on the recovery of metals from unfiltered ore leach slurries, heap leach liquors and mine drainage waters containing a small amount of suspended solids. In the case of dilute waste solutions, with suspended matter and high flow rates, filtration is usually prohibitively expensive.Continuous ion exchange operation using fluidized beds has made it possible to reduce considerably the resin inventory and to allow the treatment of unclarified liquors and slurries. The subject has been reviewed on several occasions (1. 2. 3, 4). Although fluidized beds in multi-stage columns are an improvement over previous resin-in-pulp treatment, they have complicated internal structure and I or involved automatic control systems to move the resin stages.Slater and Prud'homme performed studies on multi-stage fluid beds, and concluded that the performance of single, deep fluidized beds of resin with continuous or semi-continuous flow of both phases would be worth investigating, particularly in the case of very dilute metal solutionsoi, A pilot plant was designed and built at CANMET in a cooperative project with Dr. Slateroi. The use of deep fluidized beds of resin (with a large height/diameter ratio) for treating dilute solutions has the attraction of engineering simplicity. Extreme simplicity of equipment design is considered of paramount importance when treating, for example, mine waters at high flow rates, possibly of the order of several million gallons per day. This paper describes the development of the concept of single-stage fluidized bed continuous ion exchange arid reviews the pilotplant development of processes for the treatment of base metal mine water, cyanide waste water, uranium leach liquor and uranium mine water."

Jan 1, 1980

By S. Lun Sin

In this study, the effect of silicon on the microstructure, mechanical properties and hot tearing susceptibility of permanent mould cast AZ91E magnesium alloy was investigated. Varying amounts of silicon (0.5, 1.0 and 1.5 wt.%) were added to AZ91E in the form of an Al-53 wt.% Si master alloy. The phase formation, grain size and solidification behavior of each alloy were characterized and related to their tensile properties and hot tearing susceptibility. The results showed that the addition of silicon resulted in the formation of Mg2Si particles. The presence of these particles led to an increase of the hardness, but was detrimental to the tensile strength and elongation of AZ91E. However, silicon significantly reduced the hot tearing susceptibility of AZ91E. This was attributed to the reduction of the grain size and the decreased freezing range of AZ91E, which contributed to improve the interdendritic feeding during the last stage of solidification.

Jan 1, 2011

By Andrew J. Freyman, Graham T. Armstrong

"In September, 1968, a survey of operating mines in the Yukon and the Northwest Territories was undertaken to determine the role of Indigenes (Indian, Metis, Eskimo) on the mines, and the attitude of mine management to these employees. The operating mines in the Territories had (at that date) a total employment of 2,002 men, of which 91 (4.5 per cent) were Indigenes. Indigenes make up 45 per cent of the Territorial population (18 per cent in the Yukon and 63 percent in the Northwest Territories). The paper documents some of the problems associated with indigenous employment in mines. A study was undertaken to determine the role of Indigenes (Indians, Metis, Eskimos) in operating mines in the Yukon and in the North-west Territories. In addition to the mines north of the 60th parallel, the experience of several other Canadian mines was examined. The general picture obtained is considered to be representative of the Canadian mining industry."

Jan 1, 1969

By P. Fellner, A. Sýkorová, J. Thonstad, J. Jurišová, V. Khandl

Adsorption of S02 on alumina used in the aluminium industry, so-called smelter grade alumina, was studied in the temperature range 15 C-120 C. The specific surface area of the smelter grade alumina was 88 m2/g. It was found that at temperatures lower than 40 C, sulphur dioxide is bonded to alumina reversibly by physical forces, and the adsorption can be described satisfactorily by the Langmuir adsorption isotherm. The heat of adsorption was estimated to be -33 kJ.mor1. At temperatures in the range 80 C- 120 C, which prevail in dry scrubbers in the aluminium industry, the heat of adsorption was determined to be -56 kJ.mor1. When S02 was adsorbed at temperatures higher than 80 C, about 30 % of the S02 could not be desorbed when heating the samples up to 250 C. In the presence of S02 and oxygen, the formation of sulphate was determined at temperatures above 90 C.

Jan 1, 2006

By H. K. Olsen, B. Thomassen, H. K. Schønwandt, L. Grahl-Madsen, H. Stendal

The central part of the early Proterozoic Ketilidian orogen in South Greenland consists of an I-type granitoid batholith transected by four regional NE-SW-trending shear zones. Thebatholith was probably emplaced during subduction, from the south toward the Archaean craton in the north, in a sinistral transpressional system. A regional sediment sampling program covering5000km2shows a close connection between a gold-mineralized trend and one of the major shearzones within the epizonal facies of the batholith. The gold mineralization is not directly related to the major shear zones, but occurs in quartz-veined and silicified second-order structures. High-grade(up to 114 ppm Au over 6 m) low-tonnage mineralization is found within these second-order structures cutting both amphibolites and granitoids. The mineralization is characterized by negligible or small alteration halos. Gold is associated with various element combinations of enhanced As-Bi-W-Cu, which indicate that the mineralization is mesothermal in origin.

Jan 1, 1995

By H. K. Olsen, B. Thomassen, H. K. Schønwandt, L. Grahl-Madsen, H. Stendal

Abstract-The central part of the early Proterozoic Ketilidian orogen in South Greenland consists of an I-type granitoid batholith transected by four regional NE-SW-trending shear zones. The batholith was probably emplaced during subduction, from the south toward the Archaean craton in the north, in a sinistral transpressional system. A regional sediment sampling program covering 5000 km2 shows a close connection between a gold-mineralized trend and one of the major shear zones within the epizonal facies of the batholith. The gold mineralization is not directly related to the major shear zones, but occurs in quartz-veined and silicified second-order structures. High-grade (up to 114 ppm Au over 6 m) low-tonnage mineralization is found within these second-order structures cutting both amphibolites and granitoids. The mineralization is characterized by negligible or small alteration halos. Gold is associated with various element combinations of enhanced As-Bi-W- Cu, which indicate that the mineralization is mesothermal in origin.

Jan 1, 1995

By A. S. H. Kabir, I-H. Jung, J. Su, S. Yue, M. Sanjari

The final mechanical properties of wrought magnesium alloys are mostly controlled by microstructure and crystallographic orientation or texture. In common magnesium alloys, grain coarsening occurs during annealing process and formation of undesirable basal texture cannot be changed markedly. The aim of this work is to investigate the effect of static precipitation on microstructure and texture evolution during annealing at 250 °C after warm rolling of Mg-Al-Sn alloy. Mg-3Al-3Sn (wt. %) alloy has been designed using thermodynamic modeling software, FactSageTM, based on forming target stable and incoherent Mg2Sn precipitate within the industrial deformation temperature range. Microstructures and precipitation were investigated by optical and scanning electron microscopes and macro-texture was measured by X-ray diffraction (XRD) techniques. It was found that static precipitates form in a large scale at the recrystallized grain boundaries and retards the grain growth during annealing. Slight weakening in basal texture was also observed during annealing.

Jan 1, 2014

By M. K. Senicie

IN July, 1937, Asbestos Corporation, Limited, installed an automatic conveyor-belt scale at their King mine, Thetford Mines. The equipment was purchased 'on trial' and its performance has proved entirely satisfactory to the staff. The scale was manufactured by the Toledo Scale Company, of Toledo (Ohio) and Windsor (Ont.) and was installed by one of the Scale Company's engineers. The electrical recording equipment was installed by Keith Mercer, Reg'd, of Montreal, Canadian agents for the manufacturers, the Builders Iron Foundry, of Providence, Rhode Island. The recording equipment consists of a duplex weight-transmitter attached to the scale-head, a duplex totalizer with differential relays, a belt-speed compensator, a rate-of-delivery recorder, and a rate-of-delivery indicator. As it was desired to run the mill at maximum capacity, it was necessary to know the rate of feed at all times, so that any lessening of rate of feed or delays would be recorded and could be corrected. After having determined the rate of feed to the mill (100 per cent capacity), it was required to have weighing and recording instruments which would show: (1) The rate of feed per hour. (2) Any variations .in the load. (3) Any delays and the duration and time of the delays. Rate of tonnage recorders in the mill superintendent's office and at the point of feedi.ng were necessary, as was automatic control between the mill superintendent and the feed man. It was desired to have a permanent record of total tonnage fed per shift or day; weighing and recording mechanism had to have sensitivity to record all previously mentioned conditions. Mechanism had to be of rugged construction, and be so built that it would stay in good operating condition, with the minimum amount of adjustment and supervision.

Jan 1, 1938

By N. Saracoglu, R. H. Wallis, J. E. Betz, F. L. Jagodits, B. R. Krause

"Geophysical test surveys were conducted with various methods (EM, lP, gravity and magnetic) over the McClean uranium deposits of the Canadian Oxy- lnco Joint Venture. The result s were assessed to judge the contribution each method might make toward further discoveries of graphite-associated uranium occurrences.The best drill targets have proven to be discontinuities in graphitic conductors and locations where the tatter are intersected by fracture zones in the Athabasca. The tests demonstrated that the preferred combination of geophysical survey s is horizontal loop EM to locate graphitic conductors in the basement and VLF-EM to locate the fractures.IntroductionThe discoveries of the McClean North and South uranium deposit s (Fig. 1) are essentially geophysical successes resulting from drilling MaxMin delineations of INPUT airborne electromagnetic responses (Saracoglu et al., 1983). After the initial discovery in 1979, various geophysical methods, techniques and instruments were employed to test their effectiveness in this environment and to guide exploration for other deposit s of a similar nature in the remainder of the 260 km2 property.The McClean uranium deposits lie below 150 m to 180 m of overburden and Athabasca Group. Radioactive signatures might be expected; however, the Athabasca Group acts as a barrier to radioactive emanations. Fortunately, the uranium mineralization is associated with graphite in the crystalline basement. Prior drilling of ground electromagnetic anomalies confirmed that EM surveys could locate and out line basement graphitic conductors. However, as there were many anomalies, most of which could not reasonably be expected to be associated with uranium , there was need to identify additional parameters, related to mineralization, which could be detected geophysically and used to narrow the search."

Jan 1, 1986

By L. Dekker

"In 1979 Chevron Standard Limited and Irving Oil Limited intersected a thick, high-grade sylvinite zone in the Windsor Group in the Chevron Irving Malagawatch No. I well in central Cape Breton. This well was the third and final hole of a program designed to evaluate a non-commercial oil discovery made by Chevron Standard's Mineral Staff in 1978 while carrying out base metal exploration. Nine holes were subsequently drilled to evaluate the significance of the potash discovery. The delineation drilling proved the Malagawatch structure to be complex with the potash zone showing erratic grade and thickness distribution. Based on the drill information the potash accumulation at Malagawatch is uneconomic, however, other salt ""structures"" in the Bras d'Or Basin may in time prove to have better potential.History of DiscoveryIn 1972 Cuvier Mines discovered the Gays River lead-zinc deposit (MacEachern and Hannon, 1974) which prompted Chevron Standard's Minerals Staff to carry out a study of the Windsor basins in Nova Scotia (Figs. I and 2). As a result of this program several carbonate-hosted lead-zinc prospects were identified in the basal Windsor carbonate; one of these was at Malagawatch on Cape Breton Island . In 1978, after preliminary exploration surveys, a diamond drill program commenced consisting of 5 BQ holes (Fig. 3), three of which tested the basal carbonate. Instead of the reefoid bank facies of the Gays River Formation (Giles et al., 1979), the favoured host for economic base metal mineralization, this carbonate was developed as a laminated, pelletoidal, lime packstone more characteristic of the facies equivalent Macumber Formation (Schenk, 1967). While drilling one of these holes, No. 3-78, oil scum was intermittently detected on the drilling mud. The hole was abandoned at 191 m in anhydrite, without having reached the basal limestone."

Jan 1, 1985

By S. K. Paul

"This paper briefly describes the underground crushing and conveying system at Sherritt Gordon Mines' Ruttan Mine. A series of three steel-cord belted conveyors, with a total length of 2J55 metres and a total vertical lift of 407 metres, convey the muck from the underground crushing station to the mill at the surface. The maximum size of the crushed rock is 6 in. All the conveyors are provided with numerous safety and fire suppression devices. IntroductionThe Ruttan Mine of Sherritt Gordon Mines Limited is located 20 km east of the town of Leaf Rapids, 760 km north of Winnipeg. The orebody is multilensed, with lens width varying from 6 to 45 m. Ore production started in 1973 with the opening of a 10,000-tpd open-pit mine. Initial development of the underground mine was started in 1972 with the driving of parallel conveyor and access declines at minus-2507o gradient to the I 220-m level, and then the access ramp was further extended to the 1160-m level. Exploration drifting was done on the 1280-m and 1160-m levels from the access ramp. The final development plan for the underground project was approved in January 1977, and full-scale development and constructionwere resumed.At present, Ruttan Mine is in a period of transition from open-pit to underground mining. Ore production is now coming from both operations. By mid-1980, open-pit production will cease and all production will come from the undergroundmine.The underground mining method at the Ruttan Mine is sublevel open stoping with delayed backfilling. The orebody is divided along strike into a series of 27-m-long stopes and 15-m pillars, both 60 m high."

Jan 1, 1980

By L. A. Homeniuk, R. Bonnar

"The Fond-du-Lac uranium deposit is located on the northern rim of the Athabasca Basin. The uranium mineralization is, for the most part, confined to the Athabasca Group, which is underlain by pre-Helikian metamorphic rocks of the Western Craton.The deposit is characterized by a remarkable train of mineralized glacial erratics which led to the original discovery. The mineralization is present as a ""high-grade"" core and a diffuse ""low-grade"" aureole. The ""high-grade"" core occurs as a stockwork of steeply dipping pitchblende veins which strike N 50°E. Hematite, siderite and secondary silicate are also abundant. The ""low-grade"" aureole contains uraniferous goethite, argillaceous material and rare carbon buttons. Recent alteration to coffinite has taken place along the margins of pre-existing ore minerals.The ""high-grade"" core is 390 m long and 10 to 40 m wide, and is surrounded by an irregularly shaped zone of ""low-grade"" mineralization with a similar length and a width of up to 350 m.Comparing the Fond-du-Lac deposit to other unconformity-type deposits, several important differences can be noted:1. Ninety per cent of the ore is above the unconformity, in the Athabasca sandstone.2. The deposit is not associated with underlying graphitic rocks or a major structure.3. The clay-rich alteration zone is not extensive around the Fond-du-Lac deposit.Although there are differences with other Athabasca unconformity-type deposits, the high-grade portion below the unconformity suggests a common origin.The ore deposit is postulated to have been formed from uranium-bearing solutions which entered the stockwork of fractures. Following the reduction in part of these solutions by pre-existing carbonaceous matter and pyrite and/or chemical reaction with pre-existing hematite, deposition continued as a result of decreasing temperature and pressure. Subsequently, minor supergene redistribution of the uranium has taken place."

Jan 1, 1982

By L. A. Homeniuk, R. Bonnar

"The Fond-du-Lac uranium deposit is located on the northern rim of the Athabasca Basin. The uranium mineralization is, for the most part, confined to the Athabasca Group, which is underlain by pre-Helikian metamorphic rocks of the Western Craton.The deposit is characterized by a remarkable train of mineralized glacial erratics which led to the original discovery. The mineralization is present as a ""high-grade"" core and a diffuse ""low-grade"" aureole. The ""high-grade"" core occurs as a stockwork of steeply dipping pitchblende veins which strike N 50°E. Hematite, siderite and secondary silicate are also abundant. The ""low-grade"" aureole contains uraniferous goethite, argillaceous material and rare carbon buttons. Recent alteration to coffinite has taken place along the margins of pre-existing ore minerals.The ""high-grade"" core is 390 m long and 10 to 40 m wide, and is surrounded by an irregularly shaped zone of ""low-grade"" mineralization with a similar length and a width of up to 350 m.Comparing the Fond-du-Lac deposit to other unconformity-type deposits, several important differences can be noted:1. Ninety per cent of the ore is above the unconformity, in the Athabasca sandstone.2. The deposit is not associated with underlying graphitic rocks or a major structure.3. The clay-rich alteration zone is not extensive around the Fond-du-Lac deposit.Although there are differences with other Athabasca unconformity-type deposits, the high-grade portion below the unconformity suggests a common origin.The ore deposit is postulated to have been formed from uranium-bearing solutions which entered the stockwork of fractures. Following the reduction in part of these solutions by pre-existing carbonaceous matter and pyrite and/or chemical reaction with pre-existing hematite, deposition continued as a result of decreasing temperature and pressure. Subsequently, minor supergene redistribution of the uranium has taken place."

Jan 1, 1982

By D. Mraz

"Under high pressure in a deep potash mine, the salt rock behaves in accordance with the concept of a generalized, perfectly plastic substance. The paper presents the evidence of this behaviour and engineering concepts f or room-and-pillar design. IntroductionThe mining and refining facilities at International Minerals &. Chemical Corporation (Canada) Limited are located near Esterhaz y at the southeastern edge of the Saskatchewan evaporites. Ore extraction began in 1962 and at the present time the annual mining capacity is in excess of eleven million tons of potash ore.A generalized geological section is shown in Figure I. The mining horizon is overlay in by 100 feet of rock salt followed by a thin bed of competent dry shale. The strata in the next 1,500 feet are generally competent and locally water bearing. The Blairmore formation contains strata of water-bearing unconsolidated sand. Below the mining horizon, rock salt is interbedded with anhydrite bands.The 8-foot mining bed is distinguished mainly by grade and clay content, as there is no definite bed boundary. The chief mineral s are halite, sylvite and, in some cases, carnallite, with up to 2 per cent disseminated clay. The ore is coarse grained, with crystals averaging one-half to three-quarters inch across.The major mining problem is related to the fact that the Dawson Bay formation, overlying the evaporites, contains areas and channels that are highly porous and permeable and are filled with unsaturated brine under high pressure. Consequently, all mining areas, with no exception, must be so designed that the overburden salt stratum remain s competently supported for the duration of the mine .This paper outlines a successful engineering method of determining the stability of the pillar s and designing a stable room -and-pillar mining system."

Jan 1, 1980

By B. MohammadSadeghi, S. Bakhshivash, M. Haghshenas, F. Rahimi

"Spring-Back/Forward in sheet metals is defined as recovery of elastic strain upon unloading in a deformed sheet specimen. Since this phenomenon can cause alternation in the dimensions of a part, leading to irrecoverable compensations, the operative parameters need to be investigated, thoroughly. To assess spring-forward and effective bending parameters, V-shaped bending dies are the most commonly used experimental approach. In the present research, the effect of bending angle and punch tip radius on the spring-forward behavior of an Al-Mg-Si alloy sheet specimen is studied. To this end, a V-shaped die with four bending angles (i.e. 30°, 45°, 60°, and 90°) was designed and fabricated. Specimens with thickness of 2 mm were cut with dimensions of 50 mm×10 mm. Results show that by increasing the bending angle, the spring-forward angle decreases. In addition, smaller punch tip radiuses lead to further spring-forward. The effect of these parameters on the amount of spring-forward angle, strain distribution and homogeneity along sheet thickness was assessed using finite element analysis (FEA). Simulation results show that as the bending angle increases, the strain is developed more homogenously. Finally, micro-hardness test was used to study the effect of strain hardening caused by bending operation on strength evolution. Results show higher hardness trends for the zones in which the maximum plastic strain occurs.INTRODUCTIONPrecise production plays a significant role in the durability of a part. When it comes to sheet metal forming, this issue should be taken into account as an important factor. In order to predict the alternations, bending dies with special geometric parameters (i.e. V-shaped, U-shaped and L-shaped dies) are commonly used (Wagoner, Lim, & Lee, 2013)."

Jan 1, 2016

By I. J. Burgess, B. C. Barlow

"The electrodissolution of nickel pellets with different controlled electrical variables was investigated in an effort to mitigate plating residue in Watts bath based electroplating cells. During galvanostatic dissolution at 0.4 A dm-2, the anode potential was seen to oscillate between passive and pitting potentials. In-situ microscopy and ex-situ characterization has shown that lacy-pit formation and large, partially perforated, pit covers form during the potential decay from pitting potentials. In general, covered pitting at low current density shows increased plating residue. Using potential pulses is one way to maintain greater control over surface pitting by creating a higher density of pit nuclei while at the same time controlling their growth. Pits generated from a series potential pulses were examined ex situ for a range of pulse times and stages of pit growth were identified. An alternative method of anode dissolution was devised using potential pulses and duty cycles that allowed average current densities comparable to industrial plating conditions to be achieved. By restricting the time at pitting potentials to 0.05 s, plating residue was reduced more than six-fold in comparison to an equivalent galvanostatic experiment run at a comparable current density.INTRODUCTIONIn typical galvanostatic (direct current) nickel electroplating cells employing soluble anodes, some amount of plating residue is produced which consists of metallic nickel and impurities that detach from the bulk in the form of small fines. Significant buildup of residue requires plating operations be halted and the anode assembly cleaned of residue before operation can resume. While variables in the refining process have been shown to affect plating residue, more precise control of electrochemical variables may provide an attractive route to mitigation of residue."

Jan 1, 2016