Search Documents

By A. Otsuki

"This paper discusses the primary collector adsorption onto a sulphide mineral in mixed collector systems to understand its adsorption mechanism. UV-vis measurements were performed to identify the primary collector concentration adsorbed on pyrite, and the adsorption kinetics under different conditions were compared to distinguish their difference between single and mixed collector systems. Small amount of secondary collector addition prior to the primary collector addition significantly improved the adsorption kinetics of primary one. The result was explained by the combination of two previously proposed mechanisms (i.e., different adsorption site mechanism and multi-layer product mechanism). This study showed UV-vis measurement as an effective tool to study mixed collector adsorption behaviour.INTRODUCTIONCollectors are surfactants composed of heteropolar molecules with a non-polar and a polar group (Lotter & Bradshaw, 2010). In a froth flotation process, the function of collector is to improve the hydrophobicity of target minerals and selectively float them with the aid of gas bubbles. Because of the chemical or physical attraction between the polar group and the mineral surfaces sites, collector molecules adsorb on the particle surface with the non-polar group assigned towards the bulk solution (i.e., water), thus the mineral particle surface becomes hydrophobic (Wills & Napier-Munn, 2006).Thiol collectors are major collectors widely used in sulphide mineral flotation. Potassium amyl xanthate (PAX), dithiocarbamate (DTC), dithiophosphate (DTP), mecaptobenzothiazole (MBT) are some common thiol collectors. Previous studies reported that some mixed collectors systems enhanced the flotation performance (e.g., Bradshaw, 1997; Bradshaw et al., 1998; Rao & Forssberg, 1997). Thiol collector mixtures are often used in the flotation of sulphide ores, and discussed with the synergistic benefits (Bradshaw et al., 1998) which include lowering the total collector dosage requirements, improving the sulphide recovery and the rate of flotation as well as the improving the froth characteristics. The current paper mainly considered the mixture between two thiol collectors (PAX and DTC, considered as a weaker and selective collector, and stronger and less selective collector, respectively (Bradshaw, 1997)) to further understand their adsorption mechanism that should assist in improving the flotation performance of refractory gold ore."

Jan 1, 2016

By Robert B. Parsons

"The new Ontario Liberal government introduced its first budget in October. The changes to The Mining Tax Act proposed in the budget are mean t 10 simplify the current system without any loss of revenue to the government. It goes without saying that some operators will benefit from the changes while others will pay more taxes after 1985.With regard to ongoing matters at the federal level, the proposed carve-out legislation and the issue of northern allowances are being discussed with government officials, and a small victory has recently been scored with regard 10 the laxation of certain share transactions of prospectors and grubstakers. A report on these issues is provided herein.Ontario BudgetOn October 24, 1985, Ontario Finance Minister Robert F. Nixon tabled a budget proposing several significant changes to both the Ontario Mining Tax Act and the province’s income tax legislation.Mining Tax ActA flat rate of tax and reduced processing allowances highlight proposed changes to The Mining Tax Act. The proposed changes, with a comparison to the existing system, are set out in Table I.The most significant change is the replacement of the graduated tax rate schedule with a flat 20010 tax rate. This is a welcome change for most mine operators who viewed the high rate of 30% on profit over $20 million as counter-productive.However, the flat rate of ta x may not be welcome to all operators. Generally speaking, operators with less than $ 10 million annual profit are better off under the graduated rate system, while operators with annual profit exceeding $10 million will benefit from the 20010 tax rate."

Jan 1, 1986

By Henri-Louis Jacob

Le Québec dispose de ressources en silice abondantes et diversifiées, pouvant convenir dans l'ensemble à la plupart des usages industriels. Dans les terrains Paléozoïques des BassesTerres du Saint-Laurent et des Appalaches, les ressources identifiées comprennent les grès quartzitiques purs du Croupe de Potsdam (Cambrien), exploités notamment à Saint Canut au nord de Montréal comme source de sable de silice pour l'industrie du verre; les arénites quartzitiques des Formations de Val-Brillant (Silurien moyen) et de Kamouraska (Ordovocien inférieur) exploitées dans l'est du Québec comme source de fondant métallurgique; les grès friables de la Formation de Guigues (Ordovicien) au Témiscamingue, à partir desquels on produit des sables de silice utilisés notamment en fonderie et en filtration. Dans la province structurale du Grenville, au nord du fleuve Saint-Laurent, les métaquartzites purs du Supergroupe de Grenville représentent une source importante de silice pour la production de silicium, de ferro-silicium et de carbure de silicium. Des veines et amas de quartz ont aussi été exploités un peu partout au Québec comme source de fondant métallurgique ou de silice ultra-pure pour la production de silicium métal. Quelques dépôts de sables naturels, généralement d'origine marine ou deltaïque sont finalement exploités dans la région de Montréal comme source de sable pour des usages n'exigeant pas un produit de haute pureté.

Jan 1, 2001

By L. Voisin, K. Itagaki

In the reductive smelting of the copper concentrate like a blast furnace operation using coke as fuel and reductant or in processing the copper concentrate which contains coal in the bulk, a sulfur-deficient matte phase often coexists with an iron base alloy in the bottom of the smelting furnace. This alloy is generally called furnace residue or speiss when considerable amount of arsenic or antimony is contained in the alloy and in the extreme case of reducing condition the alloy is saturated with carbon. As a fundamental study to know the behavior of some precious metals such as silver, gold and platinum between the sulfur-deficient matte and the furnace residue or the speiss which are in equilibrium under reducing condition, the phase relations and distribution of precious elements in the Cu-Fe-S-As and Cu-Fe-S-Sb systems saturated with carbon were determined at 1473 K by a quenching method.

Jan 1, 2007

By N. E. Chaouai, M. Lavigne

"Indicator kriging is one of the non-parametric geostatistical techniques, ideal for estimating the reserves of irregular mineralizations (e.g. gold, uranium, platinum, diamonds, etc.). Such mineralizations are characterized by variograms which are very sensitive to extreme values (outliers) and very difficult to model.The classical approach to this problem in the industry is to trim off these high grades using arbitrary empirical upper limits established either from practice or subjectively. Contrary to this simplistic approach, indicator kriging discretizes the histogram of the grades (usually log normal) in several classes and carries out interpolation separately for each class. This paper gives an overview of the differences between ordinary and indicator kriging along with the steps required to carry out indicator kriging. The paper concludes with a case study involving a gold deposit estimation.IntroductionParametric geostatistics (ordinary kriging) has given us satisfactory results over the years in estimating the reserves of well behaved deposits with coefficients of variation close to 1 (e.g. sedimentary and porphyry type deposits). However, numerous problems have been encountered in estimating irregular mineralizations (e.g. small vein deposits of precious metals) with high coefficients of variation in the range of 2 to 5. Such deposits are characterized by a very small proportion of extreme values (outliers) which create distortions on the variograms (pure nugget effect) and render them useless(1,2).The solution often followed by the mining industry today is to trim off these values based on empirical limits. These limits are derived either by comparison with production results (or bulk samples) or by geological interpretations. Needless to say that such manipulations can lead to serious errors in estimating ore reserves (usually underestimation of total metal quantity), especially when production results or bulk samples are absent.On the other hand, the solution followed by the geostatisticians in the past was to smooth out the data using transforms (e.g. normal-score or natural logarithms). Such transforms are nonlinear and they required non-linear estimation techniques such as disjunctive kriging (DK) or multivariate gaussian kriging (MG) which require normal related hypotheses, not necessarily true in geology.Nonparametric geostatistics (indicator and probability kriging) have been -developed in order to handle these problems related to highly skewed distributions."

Jan 1, 1990

By C. B. Webber, L. S. Diaz

"The paper presents the approach taken by Craigmont Mines to grinding circuit control. A detailed description is given of a fully automatic control system which bases its control actions on the continuous measurement of particle size in the cyclone overflow stream. The control system holds a specified particle size in the cyclone overflow, and grinds rod mi 11 ore feed at increased rates. The principles of operation of the system used for continuous measurement of particle size are described, end the improvements in mill throughput and copper recovery over several months of continuous operation are presented.INTRODUCTION Craigmont Mines Limited is located in the south-western interior region of the province of British Columbia, approximately 230 road miles north-east of Vancouver, and ten miles west of the town of Merritt. A moderate climate, good roads and service facilities provided by the Canadian Pacific Railway, Inland Natural Gas Company, and the B.C. Hydro and Power Authority, have provided a very favorable mine and plant site.The preliminary metallurgical design of the Craigmont mill was based on the test results of samples obtained from the original 2500' level drift during 1959. Pilot plant runs and other research testing for design pur¬poses were conducted at the Canadian Exploration Ltd. Laboratory, at Salmo, B.C. The design flowsheet was altered in progressive stages from 2,000 to 3,000, and finally 4,000 tons per day as the ore reserves became better defined. Construction work on the 2,400' level mill site commenced in late 1960. The official opening of Craigntnt Mines Limited took place on September 15, 1961, a little over two years from the time of the metallurgical assessment of the original ore samples.Mill throughput to date has varied widely both on a daily and a monthly basis, due to the varying hardness of the mine ores. The grindability af the ore appears to be related to the oxide iron content, which varies from lows of 9% to highs of 20%. Daily tonnage has ranged from 5,000 tons per day with 10% iron in the feed, to 6,000 tons per day with 20% iron feeds."

Jan 1, 1973

By N. Morrison, E. J. Rogans, A. J. Macintosh, N. Schoeman

"The design of carbon-in-pulp (CIP), and carbon-in-leach (CIL) adsorption circuits has essentially remained unchanged since the early days of the carbon process for gold recovery. For CIP circuit the pulp residence time is traditionally fixed at one hour per contactor with a carbon concentration of between 15 and 20 grams per litre, and the counter current carbon transfer rates are in the region of 15% pulp recycle. For CIL, the pulp residence time is usually three hours per contact or, with lower carbon concentrations ( 5 to 10 grams per litre).The drawbacks of using the counter current CIP/CIL adsorption circuits are discussed using modeling developed for CIP/CIL plant design. Counter current CIP/CIL, circuits are then compared with the carousel method of adsorption circuit design.The use of equipment suitable for the carousel approach is discussed which is, the AAC cylindrical and pumping (MPS) screens, the AAC pump-cell plant and launder designs.Finally, two plants at the Vaal Reefs Gold Mining and Exploration Company that use carousel adsorption circuits, namely the Vaal Reefs No. 1 Gold Plant, a CIL plant with stepped contactors, and the Vaal Reefs No. 2 Gold Plant, a CIP using a very short residence time (AAC pump-cell) are discussed."

Jan 1, 1998

By K. M. Wild, C. D. Martin, F. Amann

Peak laboratory strength data obtained from low permeability clay shales/rocks often display a bilinear or non-linear failure envelope. In many of these tests pore pressures are not measured because of issues associated with back-saturation prior to confined compressive loading. In such tests the effective state of stress at failure remains unknown and provides room for speculation. The non-linear shape of the failure envelope may have several reasons including the influence of capillary forces or the tendency of a saturated clay shale to dilate as the confining stress is changed. The former stems from sample preservation, preparation or core unloading effects and represents a partly saturated state (i.e., not representative for the in-situ state); the latter represents the response of a saturated material. This contribution discusses these issues based on a data set obtained from Opalinus Clay specimens, and concludes that without a careful back-saturation processes knowledge of the underpinning reasons for the non-linear failure envelope cannot be obtained.

Jan 1, 2015

By Z. D. Hora

Sedimentary phosphate-bearing rocks are found over a considerable area of so utheastern British Columbia that extends from Fernie east to the Alberta-British Columbia boundary and from the International Boundary northward to the headwatei: s of the Elk River. Phosphatic beds occur at the following four stratigraphic levels: 1. lower part of the Banff-Exshaw sequence of Mississippian age; 2. lshbel Formation of Permian age; 3. base of the Fernie Group of Jurassic age; 4. belemnite bed within the Rock Creek Member of the lower part of the Fernie Group. To date, considerable tonnages of phosphate rock have been proven in the area. However, no commercial production has been initiated because of a relatively low P2O5 grade. Data on assays and thicknesses of the phosphatic beds are in part recalculated from the paper by Telfer (I 933) and in part from assessment reports filed at the British Columbia Ministry of Energy, Mines and Petroleum Resources.

Jan 1, 1984

By Craig Haase

A. Introduction

Jan 1, 2003

By Claude Gosselin

En 1995, la Compagnie minière Québec Cartier a mis de l'avant un projet de recherche sur la modélisation de l'écoulement des gaz pour ses fours de frittage à l'usine de bouletage de Port-Cartier. Cette démarche s'inscrivait dans un large processus de collaboration avec l'Université Laval et le Consortium de Recherche Minérale (COREM). L'usine de bouletage possède deux fours de frittage d'une capacité moyenne de 600 tonnes/heure pour chacun des fours. Les fours de frittage sont des systèmes complexes d'échange de chaleur qui fonctionnent à contre-courant (le débit de boulettes versus les débits de gaz). Pour rencontrer les spécifications reliées aux propriétés mécaniques des boulettes, le processus de fabrication requiert des mesures et un contrôle des systèmes très précis. L'information fournie par plus de 70 capteurs (pression, température, puissance, vitesse, hauteur de lit, position de volet....) est utilisée pour manipuler une vitesse de grille, cinq ventilateurs et neuf zones de brûleurs. Malheureusement, les variables qui influencent fortement les mécanismes de frittage, c'est-à-dire les débits de gaz dans les différentes zones du four ainsi que la masse de boulettes qui circulent ne sont pas mesurées. Une méthode est donc proposée pour une estimation en ligne de ces variables. La méthode est basée sur un arrangement de 65 équations reliant pressions, températures et débits de gaz dans les conduites, les ventilateurs, les sections du lit et les fuites (Gosselin, 1998). Pour des raisons de simplification de cet article, seul un sous-système du four sera présenté. Les techniques de réconciliation des données reliées à la conservation de la matière et de l'énergie montrent que la mesure en ligne du débit de boulettes mène à l'estimation des débits de gaz et apporte des avantages intéressants pour le contrôle des variables stratégiques des fours.

May 1, 2001

By A. Bouajila

To stay competitive in an open market, mineral industries have to optimise their processes, lower their production costs and improve the commercial value of their products. Up to a recent past, they were impaired in this attempt by a lack of adequate devices allowing reliable on-line and real-time process monitoring (detection or measurement). Process monitoring for process control and the product characterisation for quality control are quite different tasks. Planners and researchers should be fully aware of this when evaluating or developing monitoring equipment for on-line process control. This paper will comment on some aspects of sensor specifications, during the design and the evaluation steps, related to sampling, measurement (accuracy, sensitivity, delay and correlation to the process) and suitability to the exploitation environment. Examples of R&D projects promoted by COREM for various industrial applications will be presented.

May 1, 2001

By J. W. Reynolds

This paper describes the function of the research and development department of a large mining organization and the benefits which can be derived over the years. Examples are given of work done in rock drilling, ventilation, noise control and the development of backfill stowing machinery.

Jan 1, 1970

By Christopher R. Lattanzi

"Discounted cash flow analysis provides a means of relating the magnitude of expected future cash profits to the magnitude of the initial cash investment required to purchase an asset or to develop it for commercial production. The objectives of discounted cash flow analysis are to determine:.. The net present value of a stream of expected future cash revenues and expenditures... The rate of return which the expected future cash flows will yield on a given level of initial cash investment.In the case of mineral properties, discounted cash flow analysis is generally accepted as the preferred method of valuation, whenever sufficient data are available to permit its reasoned application. Sufficient data are required to support estimation of all of the individual elements of cash revenue and cash expenditure which will be associated with the development and operation of the property, up to the end of its estimated life. It is the accuracy of these input estimates which determines the validity of the resulting determinations of profitability and rate of return on invested capital.In undertaking any discounted cash flow analysis, it is important to recognize certain fundamental attributes of the mining industty:.. The basis of any mineral development is the existence of an ore reserve... Costs are determined by the number of tonnes mined and processed, while revenues are determined by the number of pounds or ounces of metal produced. The two are related by the recovered grade of the ore... Profit is typically more sensitive to changes in revenue than it is to changes in cost... Commodity price is a principal determinant of revenue, but it is also the factor with which is associated the greatest level of financial risk.In the end, of all of the factors which must be considered in the discounted cash flow valuation of a mineral property, the most significant are the reliability of the reserve estimate, particularly with respect to recovered grade, the price at which the product is to be sold, and the risk of not maintaining the projected level of price."

Jan 1, 2003

By Carmen M. Neculita

Optimizing the long-term efficiency of passive systems for the treatment of highly contaminated acid mine drainage (AMD) is still a challenging issue. The optimization lies, among others, on improving the understanding and quantification of metal removal mechanisms in order to predict and enhance the stability of neo-formed minerals in secondary phases. Sorption, and precipitation as oxides-hydroxides, carbonates and bio-sulfides are likely the most important metal removal mechanisms involved in passive biotreatment of both slightly and highly contaminated AMD. In the same time, the preferred mechanism is precipitation of metal sulfides that are more stable and less pH dependent than carbonates and oxides-hydroxides. However, results of relatively recent research studies performed at laboratory scale showed that sulfides accounted only for up to 15% of total metals removed in passive bioreactors treating highly contaminated AMD dominated by iron (around 500 mg/L). Several approaches were used in the aforementioned studies to understand and quantify metal removal mechanisms in spent reactive mixtures collected from long-term (12-15 months) operating column bioreactors. These included: thermodynamic equilibrium modeling and various chemical extractions and mineralogical analyses (such as single and sequential extractions, acid volatile sulfides-simultaneously extracted metals determination, scanning electron microscopy, X-ray diffraction, and thermo-gravimetric analysis). The large proportion of metals (85%) removed by sorption and precipitation as oxides-hydroxides and carbonates suggests a relatively high mobility of the neoformed minerals, especially in low pH conditions. However, no data is available on the long-term stability of spent reactive mixtures and, on the implications for the sustainable management of this type of solid waste. Lately there is almost a consensus that the efficiency of highly contaminated AMD treatment is warranted by the use of multi-step passive systems, including both chemical and biological units, installed sequentially. However, very few well-documented studies are available on the design, construction, operation and long-term efficiency of these multi-step systems. A leading example is the tri-unit passive system installed on the abandoned Lorraine mine site (Québec) to treat a highly contaminated AMD dominated by iron (about 2,500 mg/L). This tri-step system (160 m3), consisting in two bioreactors separated by a unit filled with wood ashes, achieves to date a satisfactory removal of iron (up to 99%). Moreover, based on the data collected during laboratory testing, iron was mainly removed in the wood ashes unit (from around 3,200 mg/L to 10 mg/L) by precipitation of oxides-hydroxides as predominant mechanism and only partially by sorption. However, no data is available on the actual metal removal mechanisms in the field. Overall, theses multi-step systems are more complex and their long-term performance is even less predictable than the single unit systems. This paper presents the current knowledge and the research needs on metal removal mechanisms in passive bioreactors and multi-step systems for the long-term treatment of highly contaminated AMD. KEYWORDS

Aug 1, 2013

By Douglas H. Silvey

"The historical transformations in fire -resistant conveyor belt compositions in the past 20 years have been influenced by factors of material cost, changing flame and burn test requirements, material replacements, adhesion and oil resistance considerations, increased responsibility and legal liability. Specifically, this has resulted in a swing from neoprene-cotton belts to S.B.R. blends and synthetic fibre carcasses, and tighter quality control and documentation of test data.Flame dynamics are discussed and the function and performance of the multiple types of flame-resistant additives in the flame front are presented. Specific flame and burn test requirements are described. The belt manufacturers' requirements and criteria in selecting the types of flame-resistant additives are presented.The author will describe the composition of the types of flame-resistant compounds used in a practical production, the belts that are available on today's mark et and future developments in requirements that may further transform the composition of fire-resistant belts.IntroductionThe historical transformations of conveyor belt compositions in the past two decades have been based on factors common to those leading to changes in man y organic compositional products. These factors are material cost, new materials, the customer' s changing requirements, government regulation s and increased manufacturer' s liability.As a basis for understanding the product, I will provide a brief breakdown of the conveyor belt composite. Figure 1 represents a cross section of a typical belt. A skim rubber coats each fabric ply of the belt carcass and is of a different rubber composition than the outside layer of rubber which forms the cover. This outside cover layer is designed to protect the belt from environmental factors such as heat, oil and abrasion, and other factors involved in the service condition s under which the belt will operate. In the case of fire-retardant belt s, both the skim coat encapsulating the fabric plies and the outer cover must contain sufficient fire retardancy to overcome the contribution to burning of the decomosition products of the fabric."

Jan 1, 1982

By Tetsuya Yumoto, Toshikazu Shiratori

Information on the elements contained in E-Waste is important from the viewpoint of recycling. We analyzed several components of waste electrical and electronic equipment (WEEE) collected from citizens. The distributions of the minor metals in WEEE were determined with elemental mapping and chemical analyses. The annual change in elemental composition was investigated by analyzing equipment manufactured in different years. The information will be of use for separation techniques required for future advanced recycling.

Jan 1, 2011

By James J. Roettger, Robert J. Mitchell

"The results of a series of model stope pours designed to investigate working pressures on bulkheads during hydraulic pouring of classified tailings backfill are reported. Total bulkhead pressures and fill water pressures were monitored under the condition of a fully saturated backfill. Similitude of the model testing is discussed and equations are developed to estimate bulkhead pressures under prototype conditions. The model results show that good base drainage, combined with a bulkhead setback, can reduce the expected bulkhead pressures to values such that timber or concrete block structures should be capable of supporting a saturated backfill. Introduction Bulkheads are used in underground running operations to block drift openings in order that hydraulically placed sand backfill can be contained in stope pours. Whenever possible, the sand fill is designed to have sufficient percolation rate so that excess hydraulic transport water will gravity drain out through the bulk headed drifts. This avoids costly decanting systems. Early bulkhead design assumed that the bulkhead pressure could be as high as 0h = Hy where H is the fill height and ""y is the saturated unit weight of the fill (Thomas et al., 1979)(1). A typical design pressure for a 50 m fill height would be 1250 kPa giving a design force of 12,500 kN on a bulkhead located in a drift of 10m2 in area . Typical bulkheads were 1 m thick heavily reinforced concrete structures formed and poured into a notched drift. Not only were these expensive structures but the associated problems of inside drainage systems and curing time delays increased production costs. As experience with bulkheads for large bulk pours increased and fill pressure measurements became available [see, for examples, Libby et al., 1975(2), Askey et al., 1978(3)] , 'free drainage' timber and concrete block bulkheads were designed. Substantial savings have been realized using these types of bulkheads but greater engineering design and monitoring of backfill pours is necessary to ensure that backfill pressures do not exceed the bulkhead design pressures.The effective and total stress components of fill pressure, the engineering concepts associated with the 'free drainage' design and some detailed design considerations have been discussed by Smith and Mitchell (1982)(4) . It is important to the safe use of these designs, however, that the basic engineering concepts be demonstrated and communicated to those responsible for the day-to-day backfill operations. This paper describes and explains observations from a series of model studies designed to measure bulkhead pressures in a saturated fill."

Jan 1, 1984

By Takao Oishi, Go Ohara, Toru Kitazaki, Masahiro Tanaka

"The High Pressure Acid Leach (HPAL) plant for nickel-cobalt mixed sulphide production at Coral Bay Nickel Corporation (CBNC) in the Philippines has been in operation since 2005 with a capacity of 10,000 t/year of nickel. Subsequent to the commissioning of the second plant in 2008, the production capacity increased to 22,000 t/year of nickel (Llerin et al., 2011). CBNC’s annual nickel production reached more than 24,000 tons of nickel in 2014. The concepts to achieve this capacity are the high availability and the reciprocally flexible operation of both plants. The availability depends on some factors, such as the control of impurities in the process and the equipment condition, to mention a few. In the HPAL process, it is not only the autoclave operating conditions that affect nickel extraction but also the impurities in the ore greatly influence it. The major element in the ore is iron and most of this iron is precipitated as Fe2O3, while the rest remains as Fe2+ or Fe3+ sulphate in solution. These ions in solution reduce the availability, so it is important to control the formation of iron ions by controlling the impurities in feed ore as well as the HPAL conditions. This paper presents the general HPAL process and the behaviour of impurities, focusing on iron behaviour in the HPAL process.INTRODUCTIONCoral Bay Nickel Corporation ProfileCoral Bay Nickel Corporation (CBNC) was founded on April 2002, as a joint venture of four companies; namely, Mitsui Corporation (18%), Sojitz Corporation (18%), Nickel Asia Corporation (10%) and Sumitomo Metal Mining Corporation (SMM) with a controlling stake of 54%. Aside from its capital share, Nickel Asia Corporation also supplies the ore and limestone for the High Pressure Acid Leach (HPAL) plant located in Rio Tuba, Philippines, as shown in Figure 1 (Tsuchida, 2008). The objective of the CBNC project is to produce 22,000 t/year (original design) of nickel and 1,500 t/year of cobalt, as sulphide, by the treatment of nickel laterite ore which is a low grade nickel oxide ore in the Philippines (Mines and Geosciences Bureau, 2014). The sulphide product has been exported as a raw material to the SMM Nickel Refinery in Japan for 30 years. The product of this plant, a mixed (Ni/Co) sulphide, is shipped to the SMM’s Nickel Refinery in Niihama, Japan. SMM Corporation provides the technology and management personnel to the plant. SMM Corporation also supplies the sulphuric acid, which is the main reagent for the HPAL process."

Jan 1, 2016

By C. Yoo

"Geosynthetics engineering has made phenomenal advances during the last decade in areas of manufacturing as well as practical applications. As a result, geosynthetics are now being recognized as essential construction materials that can be used to facilitate construction, ensure better performance of the structures and reduce the long-term maintenance in routine civil engineering works. The creative use of geosynthetics in geo-engineering practice is expected to continuously expand as innovative materials and products are becoming available. In this paper, a wide variety of geosynthetic products available to geoengineers to solve a wide range of problems are briefly presented along with their functions and possible applications. Fundamentals of geotextile filter design principles are then introduced for use in the tunnel drainage system. Practical applications of geosynthetics relevant for tunnel engineering are also highlighted with emphasis on the issues associated with the geotextile filter application for use in the tunnel drainage system.INTRODUCTIONGeosynthetics have emerged as essential engineering materials in a wide range of civil engineering applications, e.g., transportation, geotechnical, geoenvironmental, hydraulics, and private development since the first geosynthetic conference in Paris, 1977 (Koerner 2012). Due to their costeffectiveness, ease of installation, and well established mechanical and hydraulic properties, geosynthetics are now playing important roles in the field of geo-engineering.As indicated in the 9th Bucahanan Lecture paper by Holtz (2001), major developments in civil engineering have only been possible with the parallel developments in the technology of construction materials. For example, larger scale structures became possible with the help of developments in concrete, reinforced concrete, and prestressed reinforced concrete technology which replaced wood and building stone as construction materials. The best example of a parallel development in geo-engineering between the material and the geotechnical application may perhaps be the soil reinforcement technology which has a direct analogy with reinforced concrete as a polymeric reinforcement material provides added level of tensile resistance and stability to soils that have little to no tensile strength, thus giving additional margin of safety."

Jan 1, 2015