Search Documents

By Geoffrey C. Streeton

A continual objective of mine operations is to reduce ground control costs without compromising the overall safety or performance of the installed ground support. Any change in the ground support regime must not result in a less secure or safe workplace. The due diligence required to implement a change in rockbolting practice is extensive, particularly when the new bolting system has not been used at any other mining operation. Factors such as yield, shear strength and embedment strength must all be investigated to gain an understanding of how the rockbolt can be expected to perform. This paper also discusses the substantial cost reductions and efficiency gains which can be achieved through the introduction of the Jumbolt rockbolt.

May 1, 2001

By A. J. Hargraves

"It is difficult to quantify comparatively the gassiness of a property. The most common index to gassiness, cubic feet of gas per ton of coal mined, is very arbitrary and does not take into account the geological setting nor the mining operation. The gassiness of a virgin coal in situ can be assessed, but no method is precise and the most accurate methods involve prolonged field and laboratory experiments. In general, gassiness increases with depth. Whereas 'gas' normally implies methane, other gases such as nitrogen, carbon dioxide, etc. may be present in seam gas also. The inflammability of methane is a problem, particularly the explosibility of a methane-air mixture; also oxygen dilution is involved in high gas concentrations and some gases are poisonous even in low concentrations. Cross measuring into a virgin seam is usually not as troublesome as development in the seam, where narrow openings may require strong ventilation to dilute gases exuding from the face and sides. Total extraction presents problems of gas from the working seam, or from adjacent seams, particularly at the return side, or of gas-laden air from the goaf streaming out or sometimes surging out intermittently, again on the return side. In pillar extraction or longwall retreating special roadways may be required to allow the side-to-side and end-to-end flushing of the goaf which is somewhat inherent in longwall advancing. Layering may occur, particularly where ventilation conditions are not brisk. Outbursts of gas from adjoining seams may be induced by sudden rupture of roof or floor in caving workings. Outbursts of coal and gas from the working seam may occur, mostly in development work, under special environmental circumstances. Gas problems may be reduced or eliminated by predrainage of gas ....:. rarely successful from the working seam - usually undertaken from adjoining seams prior to escape of gas released by caving. The ideal solution - general predrainage of gas to the surface from measures prior to mining - has yet to be accomplished. • In the planning of gassy mines it is possible to make an assessment of gas contained in the seams and to estimate what proportion will be released into the mine air, but emission of gas into mine workings is never steady and at present there is no better planning criterion than experience at the mine next door!"

Jan 1, 1973

By Jef M. van der Zel

The idea of veneering rich yellow gold alloys with a low-melting, high expansion porcelain, has been a driving force for metal-ceramic research in dentistry. Since 1990, with the advent of the Carrara System (1), a low firing temperature veneering ceramic allowed the use of gold alloys with a lower content of platinum and palladium than the traditional gold-platinum ceramic alloys and thus a richer yellow color. The earlier high gold-platinum ceramic alloys contained at least 12 percent platinum group metals to allow for dimensional stability when firing the relatively high melting traditional ceramics. This amount of platinum group metals gave the alloys a greyish tinge which made them unattractively steel colored and difficult to present as ?high gold alloys?. In the 90?s the new generation universal low-melting, high expansion gold alloys gained market share at a steady rate, starting in Germany, and have now for a great part replaced the traditional gold-platinum alloys (Fig. 1). The first alloys contained 75 wt-% gold and up to 9 wt-% platinum or palladium. They provided a metal-ceramic system in which a gold alloy having an aesthetic yellow colour is fired on with a dental porcelain tailored thereto. The tailoring is meant in respect of compatible coefficients of thermal expansion, and compatible melting or softening points of metal and porcelain. The major concerns in the beginning were with thermal stability during firing, the thermal expansion coefficient of the alloy against the porcelain (compatibility) and the yellow color. In a later stage, alloys with gold contents in the range of 50-60 wt-% gold were developed in analogy with the pale yellow gold-reduced alloys that were formerly used for crown & bridge work and the white gold-reduced alloys used for metal veneering where gold was substituted in part by palladium.

Oct 1, 2003

By Wengui Su, Qi Zhang, Junce Wang, Zhijun Ma, Xingyuan Weng

"Mesoporous materials with large specific surface area, pore size, and pore volume have been widely used in many fields such as ion exchange, gas separation, adsorption, and catalysis. Mesoporous materials prepared using natural zeolite have the advantages of both acid and alkali resistance. In this work, mesoporous materials were prepared using natural zeolite as the starting material and diethylenetriamine (DETA) as a template. The resulting samples were characterized using scanning electron microscopy (SEM), X-ray diffraction (XRD) and N2 adsorption-desorption experiments. The influence of the crystallization temperature and crystallization time on the specific surface area, pore volume, pore size, and morphology of the resulting mesoporous materials are also discussed. Our results show that for an increase in both the crystallization temperature and time, the average pore size first increases then decreases, while the specific surface area first decreases then increases. Based on this work, we concluded that the optimal crystallization temperature was 2003 and the optimal crystallization time was 60 h. These conditions gave an average pore size of 17.93 nm, a pore volume of 0.048 cm3g-1, and a specific surface area of 16.48 m2g-1.INTRODUCTIONMesoporous zeolite, as the name implies, is a highly porous crystalline zeolite. This material is of interest due to its high hydrothermal stability, its adsorption and diffusion properties for macromolecules, and its excellent selectivity and activity as a catalyst. In recent years, it has become a hot spot among research of porous catalytic materials and has been widely used in petroleum and natural gas processing, fine chemical processing, various adsorption and separation tasks, and other uses (Carvalho & Urquieta- Gonzalez, 2015; Teh, Triwahyono, Jalil, Mukti, Aziz, & Shishido, 2015)."

Jan 1, 2016

By Robert B. Parsons

"During hard times, the focus on tax issues makes a slight change in direction. Mining companies contemplate the tax treatment of transactions and circumstances which are the product of a difficult financial environment. Some of these issues are discussed in this month's edition of Tax Notes.Every industrial sector in Canada is undergoing a major restructuring of some form, and the mining industry is not an exception. The longest recession since the Great Depression continues to affect the economy. Mining firms seek to bring their debt/equity ratios into line, and try to replenish depleted retained earnings by selling assets. This month, Tax Notes briefly examines some of the tax issues which are generally encountered during the course of such a restructuring process.Debt SettlementOne question which commonly arises during hard times concerns the tax treatment of a "" gain "" realized by a debtor on the settlement of a debt. Consider, for example, a simple situation where a creditor wants to protect itself from further losses, and makes a deal with the mining company to accept a cash payment of $8 million in full settlement of a $10 million loan. In financial terms, the debtor has made a $2 million gain on the settlement of the debt. What is the tax treatment of that gain?The Income Tax Act (the Act) contains provisions in section 80 of the Act and in section 5400 of the Income Tax Regulations which deal specifically with this question. First of all, it is noted that the $2 million gain is not brought directly into income for tax purposes. However, as indicated below, the gain could affect the debtor's income indirectly to the extent that certain of the debtor's tax pools must be reduced by the amount of the gain."

Jan 1, 1993

By M. Azzaz

In this paper, we report on new mechanical tests, at high temperatures, performed with a supposed better aluminium nitride (A1N) material, containing fewer oxygen. Our purpose was twofold: (i) check whether creep resistance is modified and hopefully enhanced and (ii) determine the elementary mechanisms controlling plastic deformation through transmission electron microscopy (TEM) observations of deformed samples up 10% strain in compression at elevated temperatures (1823-1923 K) under constant stress in the range 150¬250 MPa. Stationary rates are lower by an order magnitude than those previously measured in MN with higher oxygen content. All dislocations imaged by TEM look undissociated, which clearly relates the formerly observed wide dissociation to oxygen in excess.

Jan 1, 2004

By Fathi Habashi

Teaching mining, metallurgy, and geology preceded that of the other engineering disciplines. The first School of Mines was founded in 1756 in Potosi (Fig. 1) in New Spain (now Bolivia), 38 years before the first Polytechnic School (École Polytechnique) was founded in Paris. The schools of mines were also pioneers in the teaching of chem- istry. The teaching staff at these schools cre- ated the basic literature on metallurgy, mining, and geology. They analyzed and dis- covered numerous minerals and discovered the metals tungsten, beryllium, chromium, uranium, zirconium, vanadium, indium, and germanium. The history of some of the first schools is given together with biographies of some of their distinguished teaching staff.

Nov 1, 1997

By J. L. Bowlby

OWING to the pressure of routine analyses at the laboratory during the past year, work of an investigational nature on water problems has been greatly curtailed. Favourable reports by the boiler inspectors indicate that the operators are giving satisfactory attention to feed-water treatment at the several . power plants. Some of the operators prefer lime and soda, others the phosphate and soda treatment. Springhill is still on the same commercial treatment as they were using last year, and satisfactory results are being obtained. This individual preference for a particular treatment, although it may be different for feed waters of similar nature, indicates that so long as proper conditions of alkalinity and concentration are maintained within the boiler, it is immaterial what chemicals are used in the treatment. This statement refers, of course, to the low-pressure boilers. In high-pressure boilers, a treatment such as lime and soda cannot be satisfactorily employed, on account of the precipitated calcium carbonate unduly increasing the amount of suspended matter. Only one case of impending trouble was reported during the year. That was at Seaboard, shortly after the new unit was placed in operation. Dissolved oxygen, considerably in excess of the permissible 0.030 cubic centimeters per liter, was detected at various points on the feed line. It was suspected that a de-aerating heater was being operated at too low a temperature, and chemical tests, made before and after the necessary adjustments, proved that this was the source of the trouble. While it has been impossible to give mine waters the attention they require, progress can be reported in the work carried out by the Mechanical Department. Past investigation of the action of mine water on various acid-resisting alloys is now bearing fruit, and it can safely be said that repair work on mine pumps has been reduced by nearly one-half.

Jan 1, 1938

By H. Saari, D. Y. Seo, J. Beddoes, T. R. Bieler

Prior work on effects of lamellar orientation on creep rates and other mechanical properties have shown that having lamellae parallel to the tensile axis provides optimal creep resistance and good strength. Consequently, a directional solidification system was used to examine the effect of solidification rate on the development of crystals with lamellae parallel to the growth direction. The nominal chemical composition of TiAl ingots was Ti-46A1-2Mo-2Nb (at%) and the ingots were 20 mm in diameter and 180 mm long. The master alloy bars were placed in a high purity yttria mold on a copper chill plate and raised into the hot zone of a Bridgman furnace. The alloys were melted and then directionally solidified at withdrawal rates of 4, 8, and 12 mm/min. As-cast specimens were sectioned at positions of 4, 22, 66, 111, and 155 mm from the bottom of the ingot to evaluate microstructure and crystallographic texture as a function of distance from the bottom of the ingot. The directionally solidified microstructure consists of continuous columnar grains with fully lamellar structure, a network morphology of primary 13, yttria particles, and interlocked columnar boundaries. For all three ingots, the texture at 4 mm shows many peaks, with isolated strong peaks, and a slight tendency toward <111> plane normals within about 20° of the cylindrical axis. At 155 mm, all specimens showed substantially stronger clustering of <111> orientations near the cylinder axis, with the strongest clustering of poles occurring for the 8 and 12 mm/min specimens. Analysis of diffraction peaks indicates that strongly compressive residual stresses in the radial direction are present in the casting. The combined microscopy and texture analysis provides more complete understanding of the processes of directional solidification of TiAl alloys.

Jan 1, 2004

By M. J. Young, C. A. Aird

"The Gem molybdenum prospect is situated at the head-waters of Clear creek, between the Fraser river and Harrison lake, about 30 miles north of• Harrison Hot Springs, B.C. Clear creek follows a deeply eroded fault zone southwesterly through the center of the claim group. Elevations range from 2,000 feet in the creek bed up the steep slopes flanking the creek to a height of 5,500 feet. The property lies within an area underlain by schists and gneisses which strike from north to west in a broad fold plunging steeply to the northeast. This metamorphic complex has been invaded by numerous bodies of grano-diorite, much of which is gneissic. A granite plug, roughly 2,400 by 4,000 feet in size, has intruded this broad fold just west of Clear creek and encloses a circular breccia pipe 1,500 feet in diameter. In the breccia pipe, fragments of metamorphic rocks, granite and quartz monzonite porphyry are firmly cemented in a matrix of quartz monzonite porphyry. All the above rocks are cut by numerous fractures filled by vuggy quartz veins, many of which contain molybdenite. Attentien was first drawn to the area by a quartz vein, 18 inches in width, known as the Gem vein, which consists of several laminated bands of quartz and molybdenite. Since 1964, exploration efforts have been directed toward attempting to outline a large, low-grade type of molybdenum deposit."

Jan 1, 1969

By W. L. Stuewe

The Dominion Steel and Coal Corporation requires enormous quantities of bricks each year for its Sydney steel plant operations. Clay brick of all types are purchased, while silica brick is made in the Company&apos;s plant at Sydney. A description of this plant was given in a paper presented by H. B. Gillis and F. C. Morrison at the 1938 Annual General Meeting of the Institute. The rock used to make silica brick was for years obtained from a quarry at Leitches Creek, about eighteen miles from Sydney. Due to the gradual deterioration of this deposit, the Corporation was forced to look for other sources of supply. In 1945, the problem was presented to the Nova Scotia Department of Mines and, through the efforts of Dr. A. E. Cameron and Mr. J. P. Messervey, an examination was made of a silica-rock deposit some six miles northwest of Yarmouth, N.S. Preliminary samples proved satisfactory, and arrangements were made with the Department of Mines to ship to the steel plant at Sydney a fifty-ton car load for the purpose of further testing. Brick made from this sample shipment stood up very well in the furnaces. At the same time, two hundred and fifty tons of silica rock from a deposit at Lac Bouchette, Que., were purchased from the Industrial Silica Corporation, and brick made from this rock also was found suitable for our requirements. Comparative transportation costs, however, led to a decision to open the Yarmouth deposit. The silica rock, or quartzite, of this deposit outcrops at Chegoggin point along what is known as the &apos;Pembroke shore&apos;, a northerly trending section of the coast-line at the extreme southwest of the Province, in Yarmouth county. The country here is fairly flat, with elevation averaging about twenty feet above high tide, and is for the most part mantled by a growth of brush and some scrub trees, chiefly small fir. Bed-rock is generally concealed beneath three to four feet of clayey soil, but scattered outcrops of the quartzite indicated that a band of this rock, some 260 feet wide, extended inland in a northeasterly direction from Chegoggin point at least to Utleys lake, a distance of about three miles.

Jan 1, 1947

By J. -P. Tshibangu, M. Ramos da Silva, F. Descamps, C. Schroeder, J. -C. Verbrugge

"The mechanical behaviour of rock materials is largely influenced by the stress state and pore pressure; this needs to be considered in many applications, such as petroleum engineering, tunnelling or stability of underground excavations.Conventional triaxial tests (d2 = d 3) are generally used to assess the influence of confining and pore pressure. In this work, those tests are performed on a porous rock named Sorcy limestone, along with more advanced stress paths like triaxial extension (d 2 = d 1) and purely deviatoric tests with independent pore pressure control. Those tests are combined to a true triaxial study on the dry rock in order to investigate the effect of true triaxial stresses and, hence, build three-dimensional limiting envelopes accounting for the influence of pore pressure.Three-dimensional limiting envelopes of dry Sorcy limestone are built in meridian and octahedral planes. The shape of the octahedral sections changes with the mean stress from triangular to hexagonal and then quasi circular. At even higher mean stresses, the evolution continues towards a triangle with apexes oriented in the direction of triaxial extension stress states. In meridian sections, the deviatoric stress first increases with the mean stress. The transition between this deviatoric mechanism and the cap surface occurs at different mean pressures depending on the Lode angle.Terzaghi’s effective stress is found to govern the yield and plastic behaviour of saturated Sorcy limestone. Triaxial tests show that the limiting envelope does not depend on the loading path (conventional compression and purely deviatoric stress paths). In triaxial extension, the brittle-ductile transition is observed for a higher mean pressure than in triaxial compression, as previously found for true triaxial tests on the dry rock.Finally, it is shown that upon appropriate normalisation, the dry and saturated yield envelopes come very close one to each other. This suggests that only the size of the yield envelope changes between dry and saturated state (pore pressure = 5 MPa); its shape does not seem to evolve."

Jan 1, 2015

By L. C. Hsu, M. O. Desilets, P. J. Lechler, Jr. Bonham, J. G. Price, L. J. Garside

Geochemical background levels have been established for unmineralized sedimentary rocks that are elsewhere the hosts of Carlin-type gold deposits in the Getchell Trend. The Paleozoic rocks in the Winnemucca Quadrangle consist predominantly of the lower Paleozoicsiliceous and clastic sequences that were carried eastward along the Roberts Mountains thrust during the Late Devonian and Early Mississippian Antler Orogeny and the late Paleozoic Havallah and Pumpernickel sequences brought along the Golconda thrust eastward during early Mesozoic Sonoma Orogeny. Over 260 rock samples were collected from the Paleozoic sequences. Major and trace elements were determined by instrumental methods best suited for the specific elements. The general geochemical features of the Paleozoic sedimentary rocks are discussed in detail with reference to the data of average abundances of elements in sedimentary rocks. The background and threshold values of certain trace elements in sandstone, shale, and carbonate rock of one formation, as well as back-ground levels for the entire sequence were obtained. The characteristic geochemical features of the Paleozoic rocks in this area include: consistently high Ba and low Au contents (1.1 ppb, 1.5 ppb, 1.1ppb Au for average sandstone, shale and carbonate, respectively); generally low contents of those elements which may be of environmental concern such as As, Cd, Hg and Pb. Plots of major and trace elements suggest that the majority of the Paleozoic clastic rocks are related to a passive-margin tectonic setting. Samples with gold values higher than threshold are considered to have been affected by hydrothermal alteration related to gold mineralization. Most of these samples generally also have higher values of Sb, Hg, V and/or As. These observations support the use of such elements as pathfinders for gold, although V has not been identified as such before. Ba is not effective for gold exploration in this area due to the generally high background value of Ba, even though it may be an important pathfinder elsewhere.

Jan 1, 1995

By H. J. Rowley

THERE are many varieties of limestone, but for the general purposes of the pulp and paper industry, two classifications are sufficient: (1) High-calcium stone, which should be quite free from impurities and contain not less then 90 per cent calcium carbonate. (2) High-magnesium stone, containing not less than 25 per cent of magnesium carbonate. Before proceeding with detail on the use of limestone and lime in the industry, a few words regarding the pulp products made in Canada are desirable. By far the largest tonnage is made by grinding spruce and balsam logs on rotating sandstones or on artificial abrasive stones of the Norton or Carborundum types. This mechanical or groundwood pulp finds its largest use in the production of newsprint paper, of which it comprises about 80 per cent of the total fibrous substance employed-the remaining 20 per cent being unbleached sulphite pulp. No limestone or lime is directly employed in making groundwood pulp, as contrasted with the chemically prepared pulps, all of which require one or the other form of the base for their processing. Sulphite pulps comprise the next largest tonnage group. They are produced by boiling, under pressure and at elevated temperatures, spruce and balsam wood in chip form in solutions of bisulphites and sulphurous acid. The usual bisulphites employed are those of calcium and magnesium. Sodium, potassium, and ammonium bisulphites give progressively better pulps, but to date, in the absence of efficient recovery methods, cost has precluded their use.

Jan 1, 1939

By C. Okay Aksoy

In Turkey, the increasing demand for lignite has necessitated an increased emphasis on both lignite production and recovery. This emphasis has resulted in a gradual increase in the application of the retreat longwall mining method for both its product recovery and productivity benefits. Also, in order to maximize the recovery of the natural resources and to increase total production, it is necessary to take advantage of underground reserve before abandoning the mine. This means that at the end of the life of the mine, the main drift safety pillar and the shaft pillar will generally be extracted. This investigation a preliminary study of the stability of the main drift and the shaft at the Hustas Mine as the safety pillars are extracted. In this study, field surveys belonging to the underground colliery of Hustas Co. in Soma have been investigated with the help of LAMODEL working under the Laminated Displacement Discontinuity principle for the models calibrated as a results of physical model and finite element analyses. The convenience of Laminated Displacement Discontinuity Analysis has been researched in such studies. The results out of the models have been coherent with the previous studies.

May 1, 2004

By William M. Luff

"The Bathurst area has recorded mining production as early as 1837, although the bulk of the production has come in recent years. Production has been mainly from the well-known massive sulphide deposits, but vein, gossan, and a variety of other deposits have also been mined. This paper summarizes the history of the mined deposits, along with tonnages and grades produced.A number of ""firsts"" have been noted in the Bathurst area. The A Zone deposit, located in the Heath Steele area, was the first in the world discovered using airborne electromagnetic methods. Heap leaching of gold from the gossan zone at Caribou was the first operation of its kind in Canada. The Keymet mine was the first base metal (lead-zinc) mine in New Brunswick. For the past few years, the Brunswick No. 12 mine has been one of the largest zinc mines in the world.IntroductionThe Bathurst area (Fig. I) first had mining production in 1837 when copper was mined from a deposit on the Nepisiquit river (MacKenzie, 1958). The majority of the production, however, has been in recent years from massive sulphide deposits, but there are also other significant operations.Table I is a summary of Bathurst area mineral production, showing concentrator feed tonnages and mill feed grades. The table does not include peat deposits, sand and gravel, dimension stone or rock quarries. Figure I is a general geology map of the Bathurst area, indicating deposit locations. The deposits are divided into four categories: massive sulphide, vein, gossan and other. The deposits in each category are described in chronological order of exploitation."

Jan 1, 1995

"THE PACIFIC CONTINENTAL MARGIN OF CANADA is de-fined, for the purposes of this paper, as the area sea-ward from the present mainland coast of British Columbia to the foot of the continental slope. It thus coincides with A. Sutherland Brown's Insular Tectonic Belt. The region is limited to the north and south by the political boundary with the U.S.A., the location of which is still in dispute.The region can be subdivided into: (1) an interior trough comprising the Queen Char-lotte, Comox and Nanaimo basins; (2) a medial uplift comprising Vancouver Island and the Queen Charlotte Islands; and (3) a marginal shelf which is extremely narrow (Jess than 5 km) west of the Queen Charlotte Islands, widens to 160 km in Queen Charlotte Sound and is about 35 km wide west of Vancouver Island, where it is underlain by the Tofino sedimentary basin, with its• extension, the Juan de Fuca Basin, at the southern end.The medial uplift consists of a highly disturbed anticlinorium of mainly Mesozoic rocks, with a core of Palaeozoic. The rocks include thick sequences of eugeosynclinal volcanics and sediments. There is strati-graphical evidence of repeated interruption in sedi-mentation. By late Jurassic, the main eugeosynclinal phase was over and a successor basin was initiated in the interior' trough. This became filled, during Cre-taceous and Tertiary time, with sediments ranging in environment from bathyal turbidites to terrestrial conglomerates and coals. West of the medial uplift, another successor basin developed in early Tertiary times and became filled with mainly deep-water marine sediments. A third effusive sequence marks the base of the Tertiary on Graham Island and over most of the Hecate Strait region and Tofino Basin."

Jan 1, 1970

By Larry T. Yano, Gerald T. Handford

"Tailings Engineering has the responsibility for planning and coordinating tailings disposal and for ensuring the stability of the tailings dyke. The inclusion of both the planning and geotechnical functions in one team has resulted in greater efficiency in the design and planning process. Major challenges in tailings disposal facing Syncrude are in the areas of: (1) sludge disposal; (2) instrumentation and monitoring; and (3) liquefaction. Meeting these challenges will have a significant effect on the cost effectiveness and reliability of the mining operation.IntroductionThe size of the tailings disposal operation has led to the establishment of a large engineering team devoted solely to the disposal of tailings. This paper discusses: the tailings disposal operation, the role of tailings engineering, the organization, inter faces, and the present and future challenges with respect to tailings disposal."

Jan 1, 1990

By G. Gu, B. Fang, R. W. Revie, M. Elboujdaini

Electrochemical behavior of an X-80 pipeline steel, including frequency-sweep electrochemical-impedance spectroscopy (EIS), time-sweep EIS at a constant frequency and open-circuit potential (OCP) monitor, was investigated using four-point bending specimens subjected to a stress-corrosion cracking (SCC) test in a near-neutral pH environment. The capacitive loop became smaller with test duration, revealing an increase in the corrosion rate. The resistance obtained in the constant-frequency EIS test showed two regions, of which the region with a remarkable decrease in resistance transformed into a region of slow decrease, whereas the capacitance increased with test time indicating that iron dissolution was fast at first, and then a corrosion product or film formed and covered the surface, leading to the pitting formation.

Jan 1, 2005

By Marcel Vallée

"This text consists of two parts, comments on "Classification and Reporting of Mineral Resources for High-Nugget Effect Gold Vein Deposits," by S.C. Dominy, P.R. Stephenson and A.E. Annels, Volume 10, No. 3, pp. 215-233, and related comments on some features of the JORC Code.This paper is, in many respects, a very elaborate and valuable account of the problems encountered in the estimation and classification of high-nugget gold deposits. However, in some key areas, it appears to fall short of its objective to help "resolve satisfactorily most issues" and "contribute to improved estimation and classification" (abstract). One must realize that high-nugget effect gold deposits constitute a very narrow field, despite the occasional bonanzas. This is a field of mostly smaller sized deposits, where limited success and a significantly higher rate of failure occur relative to larger deposits of mostly lower grade. This is shown by the six deposits described in the paper. Thanks for contributing to greater understanding of these complex and nevertheless challenging deposits."

Jan 1, 2002