Search Documents

By E. A. Lowe, A. F. Bellamy, J. W. Smith

"In the autumn of 1977 Bethlehem management initiated feasibility studies on recovery of by-product molybdenum from concentrate produced at the existing Highland Valley mining operation. Over the fall and winter months test work was carried forward concurrent with design, flowsheet, equipment specification and cost studies. The decision was made to go ahead with a 200 ton-per-day treatment plant. Construction started in early 1978 and progressed to an initial start-up stage in mid-June. Full operational status was reached in August 1978. Operational results through August 1979 are presented. INTRODUCTIONBethlehem Copper Corporation operates a 20,000 ton-per-day Open Pit Mine and Flotation Plant located in the Highland Valley, some 30 air miles Southwest of Kamloops and 20 miles Southeast of Ashcroft, B.C.Two open pits are worked; the Iona Pit with limited reserves of higher Mo content, and the lower grade, more extensive Jersey Pit. Upwards of 150 tons per day of bornite-chalcopyrite bulk concentrate is produced, ranging 0.25% to 1.5% in molybdenum grade depending on the area mined."

Jan 1, 1980

By J. B. Boisvert, P. Oshust

A significant source of uncertainty in the diamond resource contained in kimberlite pipes is the volume of the pipes. Often the material within a pipe will be mined as ore, leaving the actual geometry of the pipe as a significant source of uncertainty. It is desirable to use stochastic techniques, rather than deterministic methods, to model pipe geometry because stochastic techniques generate multiple realizations that are reproducible and can be used to assess uncertainty in pipe geometry. The proposed methodology uses sequential Gaussian simulation of pierce point locations interpreted from drillholes through a kimberlite pipe. Kimberlite pipes are approximately cylindrical in shape; therefore, the data are transformed to cylindrical coordinates to facilitate the simulation of pipe geometry. Rather than using xyz coordinates to define the pierce points, z, ??and pipe radius are used. The radius variable can be simulated in z-??space to generate multiple realizations of pipe volume. Uncertainty in the volume of the pipe can then be evaluated. This methodology is demonstrated with a kimberlite pipe at BHP Billiton’s Ekati diamond mine.

Jan 1, 2008

By Valérie Tremblay

Plan de la presentation ?Laboratoire d?analyse des fluids ?Gestion des contaminants ?Condition Monitoring Avantages reliés aux analyses ?En savoir plus!! ?pour minimiser les coûts d?opération; ?pour prévenir les défaillances catastrophiques; ?pour maximiser le rendement des équipements; ?pour maximiser la longévitédes équipements; ?pour permettre des périodes d?entretien planifié.

Feb 1, 2008

By Paykan Safe

?? Background ?? WorleyParsons Gas Cleaning ?? PT Inco Smelter ?? Process Design Considerations ?? Furnace Control and Combustion ?? Combustion Chamber ?? Spray Chamber ?? Draft Control ?? Baghouse ?? Secondary Ventilation ?? ID Fan ?? Dust Handling Equipment ?? Project Execution ?? Heat Recovery ?? Conclusion ?? WorleyParsons Gas Cleaning ? Irving, TX ?? Formerly Gas Cleaning Technologies ?? Acquired by WorleyParsons in 2005 and now part of a global EPCM company ?? 14 years experience in off-gas system design for ferrous and non-ferrous facilities worldwide

May 1, 2008

By Shawn Healey, Ray Norcross

"Site IdentificationNew Britannia MineA 50/50 WX Gold Inc. - High River Gold Mines Ltd. Joint VentureTVX Gold Inc. is the OperatorLocationThe New Britannia Mine is located in the town of Snow Lake, Manitoba, which is situated between Flin Flon and Thompson, 420 miles north of Winnipeg.Brief Description of OperationNew Britannia Mine processes 2000 tonnes per day at an average grade of 4.5 g/t. Mill recoveries are currently 91 YO, accounting for forecast of 98,000 ounces for 1998.New Britannia Mine's mill complex incorporates conventional crushing, grinding and carbon-in-pulp technology. The design capacity of the New Britannia Mine mill is 1850 tonnes per day. The mill has processed upwards of 2300 tonnes per day, with no required upgrades.Gold recovery averaged 89.8% for 1997 compared to the planned 87% recovery expected from projected metallurgical test work. Year to date recovery mid December 1998 stands at 91.1 %Cash costs for the 1998 year to date were down to U.S. $221.49 per ounce, down 12% from the 3rd quarter of 1997. Milling costs for 1998 YTD were at Cdn. $9.38 per tonne and Cdn. $73.50 per ounce.Geology - (Orebody Description)The Snow Lake gold deposit is located within the Aphebian Flin Flon / Snow Lake Greenstone belt. This belt is composed of an assemblage of poly-deformed volcanosedimentary supercrustal sequences intruded by pre and sin tectonic ultra mafic and mafic intrusions and sin to post tectonic granitoid.The principal gold bearing rock at the New Britannia Mine is made up of quartzcarbonate material in sequence of basic and acidic volcanic rocks contained within a shear zone. The ore itself is gold associated with the sulphide mineral arsenopyrite and contains some pyrite, pyrotite, plus chalcopyrite. Proven and probable reserves at December 31, 1997 were at 4.04 million tonnes at 4.6 g/t and underground exploration continues to confirm the extension of the ore zones to depth."

Jan 1, 1999

By Bernard Jones

LTUG ? A meeting of many mining companies that are using large tires ? Introduction of the mines and size ? Companies go over their usage of tires and performance ? As a group we discuss how the manufactures are doing with supplies and performance (who's running what sizes and manufactures they are using) ? The mine's best practices they use (which ones work for them and which ones don't) ? Where the mines see themselves going in the future ? What type of tire management the mines have in place

May 1, 2009

By David G. Almond

"Economies of scale and the variable characteristics of many large ore deposits have resulted in grinding installations having large SAG mills fitted with variable speed drives. Problems associated with effective operation of this equipment has created the need for better operator knowledge of mill load behavior and the need for new instrumentation capable of providing accurate information about load movement and composition. This paper discusses two performance enhancing instruments available to address these needs.INTRODUCTIONThe economic demands of new mining projects has resulted in increased equipment sizes and this is particularly evident in milling where there are now many SAG mills operating in the range of 28’ – 40’ diameter with installed powers of 8 – 22 MW. These mills are designed to process very high capacities of ore daily2 and the variable characteristics of many of the deposits mined results in the need to vary the mill speed during processing to cater for the changes in ore hardness. Mill speed changes often result in operational problems associated with high-energy impacts striking the mill liners reducing energy efficiency as well as degrading the grinding media through breakage, accelerating liner wear and in extreme cases even breaking liners. These operational problems have given rise to the need to have instruments aimed at providing operators with accurate information in real time about the load composition and movement within SAG mills.The original concepts for operating SAG mills were derived from past experience of operation of conventional fixed speed ball mills. However, the relatively stable conditions that applies with fixed speed and constant ball charge in ball mills supports theoretical approaches to the grinding process based on energy calculations such as Bond’s Work Index concept. Later a set of parameters Si and Bij were used for describing load kinetics, but all of these methods neglect the details of load movement and how the energy is actually used inside of the mill. It is now commonly accepted as a basic rule that SAG mills grind by impact whilst ball mills grind by attrition and consequently SAG mills are designed and operated to generate a large amount of impacts by the cataracting load without paying sufficient attention to where these impacts are actually occurring. Many mills are operated on the basis that as long as the mill is consuming the expected power there is little attention given to the class of bodies using this energy and this often results in the inefficient use of energy."

Jan 1, 2005

By Fathi Habashi

"Crushing and grinding of ores and their beneficiation by washing away gangue minerals has been practiced since ancient times. Primitive crushing was done by hand pounding the ore with a hard stone then by using metallic hammers. The mortar and pestle was mechanized using a lever and when the size of operations increased in the middle ages, the stamp mill was introduced. The grindstone played an important role in grinding of ores. Panning for gold and hand sorting of minerals were two old methods of separation, now gave way to modern techniques. Flotation started in the middle of the nineteenth century by using oils to collect the mineral particles and float them on the surface of the aqueous slurry. It was only in the 1920s when it was discovered that organic compounds were affective floating agents. Textbooks written by distinguished engineers such as Rittinger, Rickard, Pryor, Taggart, Richards, Gaudin, and others contributed to the recognition of this field as a new discipline to be taught in Universities. INTRODUCTIONThe ancient Egyptians knew already that it would be easier to melt an earth rich in gold particles than another which is poor. As a result all efforts were made to enrich the gold by washing away the light gangue minerals (Figure 1). Another ancient method for enriching gold particles from a river stream was by means of fleece, hence the Greek myth of the “golden fleece”. The present day Georgia was known in ancient times as Colchis and was a center for gold working. It was known to the ancient Greek as the land of Golden Fleece. The use of special cloth to catch gold particles was also described by Agricola in his 1555 book De Re Metallica (Figure 2)."

Jan 1, 2009

By Ingrid Hann

The Triple Bottom Line ? Economic Sustainability ? Creation of Joint Venture companies ? Planned evaluation of other kimberlites ? Social Sustainability ? Impact Benefit Agreement and Participation Agreements ? Education and training initiatives ? Environmental Sustainability ? Environmental management ? Mine closure planning

May 1, 2008

By K. Najim, D. Hodouin

"The raw ores which are processed in mineral processing plants exhibit very strong variations of their physical and chemical properties. As a consequence, the performances of the comminution and separation processes vary greatly from time to time. Model-based control strategies improve the performance of the plant; however, they require some form of adaptation to cope with the variations of the are properties.This paper deals with the use of adaptive techniques for the control of mineral processes. It begins with a survey on adaptive control algorithms including parameters estimation aspects. Then several examples dealing with crushing, rod, ball, autogenous and semi-autogenous grinding, flotation , drying and calcination processes are reviewed.IntroductionThe operation of the various processes of mineral processing plants (crushing, grinding, flotation, dewatering, etc.) is generally controlled using empirically tuned regulators of constant structure, such as PID controllers. To improve the operation performance, mineral processors try to implement specifically designed controllers, i.e. controllers based on plant dynamic models. Most of the time, these techniques improve the control of the mineral processing installations. However, modelling is a complex procedure because of the problems of measurement and data management, specific to this industry, and because of the variations of the model parameters. In this context model-based control strategies do not always bring the expected improvements or are sometimes discarded and replaced by more conventional techniques .The sources of variation of the dynamic behaviour of mineral processing systems can be classified into three categories: (I) the inherent changes of the raw ore properties (composition, grindability, mineralogical texture, etc.); (2) the process tuning modifications (grinding media loads, number of hydrocyclones, slurry level in flotation cells, agitation speeds, etc.); (3) the feedrate variation of the ore, water, chemical reagents, etc. All these factors change the fundamental properties of the process dynamics such as the grinding or flotation rates and the residence time in the equipment. The simplified linear models which are used to describe the process dynamics are not able to track the complex behaviour of the mineral processing systems when the amplitude of the sources of variation are too large. The mismatch between the model and the plant behaviour is then frequently a cause of model-based controller failures."

Jan 1, 1992

By J. Chlopas, D. J. Barratt, M. V. Sharp

"This paper describes the modifications made to the Fox Mine copper concentrate bin in order to obtain a continuous flow condition. The design of these modifications is based on test results obtained on Fox Mine concentrate using the flow factor testing machine in the research facilities of Cominco at Trail, B.C.The original design consisted of a cylindrical steel bin on a concrete slab with two slot-discharge openings. Based on predictions of the maximum mass flow hopper angle for conical and wedge shaped hoppers for the concentrate on various potential bin lining materials, Ultra-High Molecular Weight (UHMW) Polymer was selected as a liner.Using the recommended angles for conical and wedge shaped hoppers, the profile of the bin base was changed to suit the existing slot openings.The initial method of fastening the liner resulted in failure of the connections. Subsequent modification to the zinc concentrate bin fastener system proved satisfactory and it has now been in operation for over one year without any separation of the lining material.Utilization of flow testing procedures on concentrate samples has demonstrated that proper design of storage bins or hoppers to achieve continuous flow can be incorporated into the design of new plants."

Jan 1, 1978

By Dave Price

"Canada is scheduled to become the 4th highest diamond revenue producing country in the world by year 2004 with the already operating Ekati Mine and the anticipated operation of the Jericho Mine in 2002 and the Diavik Mine in 2003.This paper provides an overview of worldwide diamond production statistics and a brief introduction to a diamond processing plant. The dense medium separation (DMS) extraction process is presented and this process is discussed in more detail with respect to the extraction of diamonds in terms of feed preparation, dense medium, dense medium cyclones, ferrosilicon recovery and dense medium cyclone operating efficiencies.INTRODUCTIONThe Ekati Diamond Mine in the Northwest Territories started commercial production of diamonds in the 4* quarter of 1998. At full production, the mine is anticipated to produce annually some 3 million carats of diamonds. The Jericho Mine in Nunavut Territory and the Diavik Mine in the Northwest Territories are anticipated to come into production in the 1'' quarter of 2002 and 1st half of 2003 respectively. The combined annual diamond production of these three mines will total approximately 10.34 million carats by 2004, making Canada the 4~ highest diamond revenue producing country in the world.A diamond processing plant initially utilizes crushing, scrubbing and screening in the beneficiation process to liberate diamonds from kimberlite ore and size the product for further treatment through DMS. Alluvial diamond operations do not require initial crushing and scrubbing but incorporate a feed preparation and sometimes a recrush facility with the DMS plant. The heavy sink product from the DMS, which contains diamonds, is further upgraded through x-ray separation and high intensity magnetic separation prior to producing the final diamond product.DMS is a relatively simple separating principle. A mixture of particles of different density is immersed in a dense fluid, so that particles having a density lower than that of the fluid will float while those of heavier density will sink. The translation of the float-sink principle from a laboratory method to continuous industrial practice offers the prospect of very precise mineral separations based on density differences alone."

Jan 1, 2000

By G. S. Farnham

Abstract This paper lists the interests of the Physical Metallurgy and Chemical Research laboratories of the Metallgesellschaft, which were visited by the authors, members of a group of Canadian investigators sent to Germany by the Department of Reconstruction in 1945. The Physical Metallurgy Research Laboratory The following information was obtained from Professor E. Schmid, Chief of the laboratories. It is understood that Dr. Schmid is a former Nazi and was to be removed from his post in November (1945). Aluminium Research The laboratories investigated the corrosion resistance of the high-strength aluminium-magnesium-zinc alloys. The same test procedure as used by V.L.W. was followed and Dr. Schmid co-operated closely with Dr. Brenner on this project. Intercrystalline corrosion was combatted by additions of chromium, titanium, or vanadium, and the work in this field parallels that of Dr. Brenner of V.L.W. * Dr. Schmid reports that Bollenrath and Siebert believe that corrosion difficulties with these alloys can be overcome to some extent by heat treatment. He himself was of opinion that the correct answer lay not only in correct alloying but also in correct heat treatment. The heat treatment involved either interrupted quenching or a change in quenching rate from a solution temperature of 500°C. The procedure is either a slower cooling from solution temperature or an interrupted cooling with a holding period at l50°C. Work had been done on piston alloys, the 11-13% Si, 1% Ni, 1% Cu, and 1% Mg being the favoured material. This is called Lo-Ex and is similar to Mahle 124 or KS1275.

Jan 1, 1946

By Manqiu Xu, Songtao Yang, Zongfu Dai, Robert Pelton, Carla Abarca

"Fine mineral particles are difficult to process by flotation because of their low collision efficiencies with air bubbles. Decreasing air bubble size and increasing mineral particle size through flocculation are the most common approaches to improve flotation efficiencies. Herein we demonstrate that nanoparticle flotation collectors can be engineered to selectively induce fine mineral particle aggregation and promote flotation.Flotation tests of clean fine pentlandite (Pn) and Clarabelle Mill (CBM) rock tails and pyrrhotite (Po) tails that contained significant amount of fine pentlandite have confirmed that the nanoparticles can serve as both collectors and selective flocculants for fine pentlandite. In the case of clean fine Pn, the nanoparticle collectors virtually can float almost all Pn fines. Scoping tests on CBM tails have shown significant improvement in nickel recovery. Addition of nanoparticles as a flotation aid can recover 20% of the nickel contained in the rock tails and 40% of the Pn contained in the Po tails compared to current mill operations giving 0% nickel recovery from rock tails and no Pn selectivity from Po tails. Ongoing work includes attempts to identify optimal strategies for employing nanoparticles in fines flotation.IntroductionFine particle flotation is an industry-wide challenge in mineral processing. Fine mineral particles are difficult to process by flotation because fine particles have low mass and thus low momentum, which results in their low collision efficiency with air bubbles (Dai, Fornasiero, & Ralston, 1999). In addition, fine particles have not only high specific surface area but also more active surface area, which causes high reagent consumption. For base metal sulphide minerals, particle size between 10 µm and 70 µm is a typical range where high flotation recoveries can be achieved with conventional flotation chemistry and acceptable cell residence times. For pentlandite, the flotation recoveries decrease sharply when the particle size is below 10 µm and hydraulic entrainment is the dominant mechanism, giving recoveries proportional to water recovery and no Pn enrichment. (Jameson, Nguyen, & Ata, 2007)"

Jan 1, 2015

By Donald Leroux, Lori Lynn Smith, Robert Hutchison

"The grinding circuit of the Heath Steele concentrator was sampled under five different sets of operating conditions. The balanced results of the sampling campaigns were used to calibrate steady-state rod mill, ball mill and cyclone models using a commercial simulation software package (JKSimMet® ). Thirteen process variables had the potential to affect significantly the performance of the grinding circuit. Statistical-Design-of- Experiments techniques were applied to plan the suite of simulations in order to improve the quality of and minimize the time to find the optimal solution. The effect of each factor on three performance indices (the cyclone overflow size distribution, the circulating load and the cyclone underflow density) was modeled with empirical polynomial relationships using another software package (Design-Expert@)T. he conditions under which the cyclone overflow size distribution was maximized while respecting circulating load and cyclone density constraints were identified using these relationships. Among the most interesting results is the prediction of a set of conditions where the circuit target size distribution is achieved with only three ball mills instead of four.IntroductionProduction at the Heath Steele concentrator (near Miramichi, New Brunswick) started some 43 years ago at a rate of 750 t/d. The plant capacity was increased to 4000 t/d through successive expansion phases in the seventies (Sapiro, 1977; Johnston, 1978). However, as a result of depleting ore reserves, the plant throughput had to be gradually reduced to the current production rate of 2700 t/d. Heath Steele Mines currently have proven and probable reserves which would see it producing until the end of 1999 (Noranda Inc., 1997).An analysis of the grinding circuit of the Heath Steele concentrator was recently commissioned to identify opportunities for reducing operating costs while maintaining budgeted mill throughput and metallurgical performance. Since the plant will likely be operated below nominal capacity for the rest of its lifetime, the possibility of improving grinding efficiency by operating with fewer ball mills and/or crushers was contemplated."

Jan 1, 1999

By R. J. Schafer-Frentz, T. G. Joseph, M. Curley

"Greenhouse gas emissions—specifically of carbon dioxide—are a concern in Canada, where industrial sectors such as mining are stringently regulated for carbon release. Cumulative emissions are positively related to fuel consumption, which is controlled by several factors. This study investigates one of these factors: the product of vehicle speed and running surface total resistance (TR; sum of rolling resistance and grade resistance). Results show that TR directly affects fuel consumption and emissions—a relationship that is mathematically predictable. Fuel consumption and emissions, which are principally associated with the durability or deterioration of wearing course materials, were analyzed to aid selection of road construction capping material of low rolling resistance. In the oil sands region in the province of Alberta, ground conditions change seasonally. Therefore, the annual fuel consumption for the same wearing course material was also compared. Results demonstrated that haul truck size was a contributing factor, but vehicle speed and TR more strongly influenced fuel consumption and emissions. ¦ KEYWORDS Carbon dioxide, Emissions, Fuel consumption, Grade resistance (GR), Greenhouse gas (GHG), Haul truck, Rolling resistance (RR), Total resistance (TR) RÉSUMÉ Les émissions de gaz à effet de serre (GES), et particulièrement celles de dioxyde de carbone, sont un problème au Canada, où les secteurs industriels tels que l’exploitation minière sont rigoureusement réglementés pour leurs émissions de carbone. Les émissions cumulées sont indéniablement en lien avec la consommation de carburant, qui est contrôlée par plusieurs facteurs. Cette étude examine l’un de ces facteurs, à savoir le produit de la vitesse du véhicule et de la résistance totale de la surface de roulement (la résistance totale, ou RT, est la somme de la résistance au roulement et de la résistance due aux rampes). Les résultats montrent que la RT affecte directement la consommation de carburant et les émissions, un lien qui est mathématiquement prévisible. La consommation de carburant et les émissions, qui sont principalement associées à la durabilité ou la détérioration des matériaux composant la couche d’usure, ont été analysées afin de contribuer à la sélection de matériau de recouvrement pour la construction de routes ayant une faible résistance au roulement. Dans la région des sables bitumineux de l’Alberta, les conditions au niveau du sol changent à chaque saison. Ainsi, la consommation annuelle de carburant pour le même matériau composant la couche d’usure a aussi été comparée. Les résultats ont montré que, si la taille des camions de transport est un facteur déterminant, la vitesse des véhicules et la RT influencent davantage la consommation de carburant et les émissions. ¦ MOTS CLÉS camion de transport, consommation de carburant, dioxyde de carbone, émissions, gaz à effet de serre (GES), résistance au roulement, résistance due aux rampes, résistante totale (RT)INTRODUCTION In Canada and around the world, global climate change has become a topic of great concern and discussion. Pres-sure on world leaders to quickly reduce their carbon footprint is prevalent, prompting new standards and regulations in various industries, including mining and oil and gas. In 2017, the Government of Alberta implemented a carbon tax. The majority of mining activities in this province are truck-shovel operations, where a large fleet of ultra-class trucks is loaded by shovels. Ultra-class haul trucks, classified as those with a capacity of 218–363 tonnes (t), emit high levels of carbon as they travel to processing entry points and waste dumps as designated by the mine plan and mine dispatcher. Mined ore and waste is typically moved over two 12-hour shifts per day throughout the year."

Jan 1, 2019

By Fabien Miller

Automation technologies are increasingly envisaged to improve underground mining productivity. However, the technologies need to be used and adopted gradually in order to get the best benefits. This paper presents the technical and operational aspects of autoguided production vehicles at Brunswick Mine. During 2001 Noranda?s Brunswick Mine has successfully commissioned an automated haulage zone where two optically guided trucks transport ore from a remotely operated chute to two orepasses. Operational advantages include increased system capacity and enhanced safety and comfort for the operator. The data obtained up to now indicate that the system can operate reliably in mine production

May 1, 2002

By M. Poirier, J. H. Mbouche

"The research question of the present work is the following: at which speed should a rotary sample divider operate in order to produce representative samples of iron ore concentrate? In order to solve this problem, the representativity of a rotary sample divider treating iron ore concentrate from Iron Ore Compagny (IOC) Carol Lake mine in Labrador City was studied in the laboratory of mineral processing of “CEGEP de Sept-Îles”. The rotary sample divider speeds tested are: 20, 40, 50, 60, 80 and 100%. The results show differences in both weight and particles sizes distributions with respect to the various rotation speed used. 20% has shown to be the speed that generates an almost normally distributed samples for both weight and particle size. As the speed of the rotary sample divider increases, the polygon of frequency for weight distribution progressively becomes a two modal distribution curve. 40, 50 and 100% speeds generate normal samples distribution curves with respect to particles size only. 60 and 80% are the speed to be avoided since they generate multiple modal distribution curves for both weight and particles size.IntroductionIn the mining industry, samples representativity is part of the key elements for management decisions. In fact, “Sampling provides vital information to plant operators, clients and geologists to profitably run and operate iron ore mines and plants” (Kevin Thorne et al. 2007). At the laboratory scale, several types of techniques’ are currently used to perform sampling. This include: grapping, alternate spading, quartering, riffles divider and rotating divider etc.. Among all these instruments, rotary divider is the most commonly used. Nevertheless, the usage of a rotary divider is not a guaranty for samples representativity since the results have shown to be related to running speed of this instrument. For the present research work, the idea is to use iron ore concentrate to quantify the representativity of a rotary sample divider. In other words, the research idea is to determine the speed at which a rotary sample divider produces representative samples while treating iron ore concentrate from Carol Lake mine. The present report will give an overview of the methodology used and the principal results obtained."

Jan 1, 2016

By B. Goard

"IntroductionCemented backfill has been placed underground in slurry form in Inco Limited's Ontario Division mines since the early 196Os. The slurry was traditionally mixed on surface at between 65 and 70 wt% solids* and transported underground via gravity through a borehole-pipeline distribution system. This method of placement, while simple and dependable, has proven to be costly because of the large amounts of transport water involved.A significant quantity of the slimes buildup on mine levels is caused by the backfill water carrying cement and other fine material out of the stopes. The level cleanup and eventual pumping or hoisting of the slimes and water back to surface result in substantial indirect backfilling costs.The cement that remains in the stope is always overhydrated because of the high water cement ratios that exist. As a consequence, high concentrations of Portland cement must be added to the backfill to produce the fill strengths required for the different mining methods.Pouring backfill at these densities also demands extensive fill preparatory work in the stopes to withstand the hydraulic heads created by the slurried fill. This, along with the delays in pouring necessary to allow for water drainage, result in significant losses in productivity.These negative aspects of slurry placed fill has led Inco Limited to investigate several methods of transporting backfill underground via pipeline, at higher densities (i.e. 75 to 95 wt.% solids). Three separate transport methods are presently being experimented with by the Company's Mines Research Department. Each utilizes a different technique or form of flow transport, i.e. concrete pumping technology, high density slurry flow, and pneumatic conveying."

Jan 1, 1987

By Stephan Buys, Dan Curry, Chris Rule

"The use of fine grinding (FG) in mineral processing is well established. The application of FG in the South African platinum industry is more recent and it’s use in the recovery of PGM’s from dormant tailings dams is unique. Anglo Platinum uses IsaMill FG technology at their Western Limb Tailings Retreatment project (WLTR) near Rustenburg in the North West Province of South Africa.In December 2003, Anglo Platinum commissioned the first purpose built tailings re-treatment facility for PGM recovery in South Africa. The concentrator re-treats Merensky ore tailings from concentrators that operated early last century. The WLTR facility takes advantage of modern technology, such as FG, to economically recover PGM’s from material historically considered as waste. The WLTR concentrator has a capacity of 4.8 Mtpa, and has been designed to easily expand to 10.8 Mtpa. The flow sheet includes recovery of tailings by high pressure water monitoring, ball milling, rougher flotation, rougher concentrate regrinding and cleaner /recleaner flotation.The rougher concentrate is reground in an IsaMill, which is a stirred mill that operates with inert silica sand grinding media. For this project, Anglo Platinum required a stirred mill of a unit size not previously available. Xstrata Technology and Anglo Platinum collaboratively developed the largest wet, fine grinding mill available; the M10,000, 2.6 MW IsaMill.The use of IsaMill technology was enabling for the WLTR project, as it allowed smeltable concentrate grades to be produced from the oxidised, slow floating tailings. The economics and practicality of fine grinding has fundamentally changed with the M10,000 IsaMill. Flotation is transformed by high intensity attritioning in the inert media environment, and the narrow size distribution of product in open circuit configuration. The use of conventional steel media grinding to improve fine particle flotation is limited due to the oxidation of liberated mineral surfaces inherent in these environments."

Jan 1, 2005