Search Documents

By A. Saigal

The effect of temperature on the cutting forces during machining of alumina reinforced aluminum composites was investigated, Aluminum 6061, 10% Al2O3 reinforced composite and 20% Al2O3 reinforced composite were tested, A 5/8-inch diameter high-speed steel end mill, a Micro 100 TiN coated single edge endmill cutter and a two-fluted solid carbide insert cutter were used for tooling, The results, in general, showed an increase in the cutting forces as the temperature of the material increased, From the raw data, there are temperatures ranges in which the force data did decrease but they were insignificant with regards to predicting a downward trend. A regression analysis was used to understand which variables had the greatest affect on the forces being generated, The correlation and regression analysis showed that at 600 rpm (velocity: HSS- 98,2 sfpm, Micro 100 cutter - 78,5 sfpm, solid carbide cutter - 192,4 sfpm) the tooling, the workpiece material, built up edge, and temperature were statistically significant factors in the test, Tooling was a significant variable in all testing, The smallest forces recorded during machining were generated with the solid carbide two-fluted endmill cutter, Visually, the solid carbide tooling produced a better surface finish during the testing which made it the tool of choice, In addition, the force data proved that as the cutting speeds were increased, the cutting forces decreased.

Jan 1, 2005

By Dwayne D. Tannant

This paper presents a new mining concept for oil sands called ?hydraulic underground mining of oil sands? or HUMOS. While this mining method is still at the conceptual stage it has great promise to allow extraction of bitumen from areas that are currently uneconomical or technically infeasible using surface mining or steam assisted gravity drainage. HUMOS is founded on a combination of recently proven technologies such as directional drilling, water jet cutting of oil sands, slurry transportation, cold water extraction of bitumen, and thickened tailings. One key component in the mining concept is the caving of oil sands and the creation of an underground cavern. Scaled-down physical models will be designed and built to demonstrate water jet cutting, cave development, and insitu primary bitumen separation. These will be used as a 'proof of concept'. On-going research will establish and prioritize issues that need to be resolved, outline key areas where further research is needed, foster establishment of research teams to divide and conquer the important questions, and create framework for future coordinated research efforts.

May 1, 2001

By K. van Netten, T. P. Ernst

"Froth flotation has been used successfully for about a century in the beneficiation of both coal and mineral particles. With the on-going trend towards lower feed grades, however, there is a need to transform this technology in ways that can deliver ultrafast separations, with strong selectivity, and recovery, covering a broader size range. It should be recognised that the hydrophobic effect, with its highly selective and long-range interactions, will most likely underpin any new technology. We identified the separation of the concentrate from the tailings as the rate determining step of conventional flotation technology. This limitation was then addressed by developing a novel flotation technology, insuring the formation of a concentrate that could be separated more rapidly from the tailings. We introduced a novel binder medium, a highly concentrated water in oil emulsion, to act as the focal point for hydrophobic adhesion, effectively replacing the air bubbles used in conventional flotation. The hydrophobic particles adhere to and become embedded within the binder, forming saturated agglomerates that float upwards. Moreover, by forming these large and resilient agglomerates, the product can be quickly dewatered over a screen and separated almost immediately from the tailings. Remarkably, this new binder permits residence times in the order of a few seconds under batch conditions. This paper examines the performance of the technology as a function of the oil wt% added to the slurry. The paper also examines the performance of the technology as a function of the particle size, showing a decline as the particle size exceeds 0.50 mm.INTRODUCTIONFroth flotation involves the collision and adhesion of hydrophobic particles to rising air bubbles, the carrying of those particles from the bubbly-pulp zone into a froth zone, and subsequent drainage and migration of the pulp to achieve the final concentrate (Wills, 2006). Within a Jameson Cell the feed slurry and air bubbles are brought into intense contact within the active area of the downcomer, achieving rapid kinetics of hydrophobic particle adhesion to the air bubbles (Harbort et al., 1994). However, once the bubble laden product and tailings emerge from the downcomer there is the need for separation of the concentrate from the tailings, an inherently slower process. In other devices such as mechanical cells the initial kinetics of particle adhesion are far slower, relying on the turbulent eddies throughout the cell, while in a column the kinetics rely upon an even slower process of bubble interception with suspended and settling particles (Gorain, 2007). However, in all cases the driving force for segregating the bubbles from the tailings, and the drainage of the froth are inherently the same. We do note, however, recent advances by Galvin and co-workers in achieving so-called Fast Flotation, utilizing a system of inclined channels to dramatically increase the segregation rate of bubbles from the tailings, permitting much higher gas and feed fluxes to be applied, achieving up to a ten-fold throughput advantage (Dickinson et al., 2014). Any further improvement within the existing flotation paradigm would require the introduction of centrifugal forces, but this would also require the formation of much finer bubbles than is typically used given the tendency of relatively large bubbles to reach a limiting slip velocity due to deformations and increased drag. Across all flotation devices we argue the rate determining step remains the segregation of the bubbles from the tailings."

Jan 1, 2016

By W. Blum

Progress made in improving the creep resistance of Mg alloys is reviewed with the emphasis on microstructural interpretation. Experimental results on the increase of creep strain with time at constant stress a measured for limited times and strains are displayed in a transparent form as creep rate-strain diagrams from which the minimum creep rate stress is safely derived. In addition, data on the thermal stress component a derived from high-precision a-reduction tests are reported. Within a simple statistical dislocation model these data allow one to quantify the relation between dislocation velocity v and a . In combination with structure evolution laws this relation serves as a basis for modeling the creep rate. New alloys have distinctly higher creep resistance than AZ91 where precipitation hardening plays a minor role. This is due to hardening by intermetallic phases which may form a continuous skeleton along the grain boundaries (e.g. Ca-alloyed AZ91) and/or submicron-sized precipitates within the grains (MRI230D, Mg-Zn-Ca alloys).

Jan 1, 2006

The NorthMet deposit of PolyMet Mining is located in northern Minnesota, adjacent to the Iron Range. The deposit is polymetallic with values of Cu, Ni, Co, Zn, Pt, Pd and Au. The processing route selected for extraction of these values utilizes bulk sulfide flotation followed by hydrometallurgical treatment. The hydrometallurgical process has been thoroughly tested on the bench and pilot plant scale at SGS Lakefield Research. The major steps in the process are; ? Chloride-assisted total pressure oxidation for extraction of base and precious metals ?Thickening/filtration/washing of the barren residue from total oxidation ? Reduction and precipitation of Au, Pt, Pd from the oxidation solution ? Partial neutralization of autoclave acid using limestone ? Copper SXlEW for production of copper cathode ? Treatment of a portion of the raffinate from Cu SX to recover NilCo/Zn as either a mixed Ni-Co-Zn hydroxide or as separate Ni hydroxide, Co hydroxide and a Zn sulfate solution. ? Recycling of the remaining raffinate to the autoclave as coolant The process flowsheet, chemistry and bench/pilot plant test results will be reported in this paper.

Jan 1, 2007

By W. T. Irvine

"The H.B. Mine, a zinc-lead operation of the Consolidated Mining and Smelting Company of Canada Limited (Cominco), is in south central British Columbia, on Sheep Creek, a west-flowing branch of the Salmon River. It is 3 miles by road from B.C. highway No. 6, 30 miles south of Nelson, B.C., with an excellent highway connection to the smelter city of Trail, 35 miles from the mine. The nearest permanent settlement is the village of Salmo, 7 miles distant by road. The mine is situated along a belt containing other important zinc-lead deposits, including those of the Canadian Exploration Company, 3 miles to the south, and the Reeves MacDonald mine, 9 miles distant again to the southwest.Deeply oxidized outcrops were located in 1907 on the north side of Sheep Creek valley by two prospectors named Horton and Benson. The property was given the name H.B., after the two discoverers, and there commenced a long and intermittent series of mining operations designed mainly to develop and extract oxidized lead-zinc ore. In 1925 a determined attempt was made by a British syndicate to develop a large tonnage of sulphide ore, but this ended in failure after some 3,000 feet of lateral development had been done. In 1927 Cominco acquired the mine, but it lay idle until 1946 when a geological study was followed by a program of surface drilling which encountered extensive sulphide mineralization. An underground development program revealed more details of the deposit, and sufficient ore was found to warrant construction of a 1,000-ton mill. Mine preparation and mill construction were completed by early 1953, but production was deferred due to low metal prices. The mine was finally brought into production early in 1955."

Jan 1, 1949

By Deng Yang-wu, Zhang Yan, Chen Chun-fei, Luo Xian-ping, Luo Cai-gui

This paper summarizes the ecological imbalance status of abandoned rare-earth element (REE) mines in southern China. These include large areas of vegetation damage, serious water and soil erosion, landslides, mudslides, heavy metal pollution, water pollution, soil contamination, and fluorine pollution. The causes which lead to the ecological imbalances at abandoned rare-earth mines are analyzed, such as: the inadequacies of using vat leaching, heap leaching, and in-situ leaching processes to extract REE resources; low mineral thickness and low grade of REE ore; and low utilization rates of the resource. Southern ionic REE resources are not fully integrated, with limited access and ineffective supervision of REE mining by relevant departments. The ecological recovery research for ionic-type REE mines is lagging behind, and there is no deployable ecological restoration method for REE wasteland. In the end, the following suggestions are made to improve the ecological imbalance status of rare-earth mine in southern China: develop new rare-earth extraction processes, accelerate the integration pace of REE resources, increase investment in ecological restoration research in rare-earth wasteland, and so on.

Jan 1, 2014

By Ralph L. Rutherford

Introduction During the past twenty-five years we have seen considerable exploration for oil on the plains of southern and east-central Alberta. This exploration has to some extent gone on in cycles, with periodic starts, stops, and occasionally some reversals. Each major attempt is usually supplemented by the application of some new method of exploration and, following each period of exploration, drilling tests are made. Whereas oil-bearing horizons are the ultimate objective of these explorations, the preliminary investigation frequently aims at a discovery of structure based on the long accepted belief that accumulations of oil and gas are to a marked degree structurally controlled. At the inception of this general exploration for oil, it was natural that attention should be directed to areas where there was surface evidence of deformation of the underlying strata, but, as the programme progressed, it was found that these surface manifestations of structure were often deceptive when attempts were made to project them to depth, to involve the deeper strata. Drilling of test wells was the only satisfactory method of obtaining exact information.

Jan 1, 1946

By P. W. Waggitt

ABSTRACT From approximately 1986 until 2000, uranium production was at a historic low. In 2003, uranium mineral exploration surged, despite the global financial crisis; however, the shortage and aging of qualified and experienced operators and regulators might soon become a constraint to this upsurge. This is true for all types of engineers, geologists, other scientists, tradespeople, and technicians. The situation raises questions about how the global mining industry in general and the uranium sector in particular will cope with future staffing needs. In this paper, the author examines the current situation and describes how some organizations are seeking possible solutions.

Jan 1, 2014

By S. D. Tolgyesi

Kidd Creek Background ? Located in Northern Ontario, Canada ? Underground base metal mine ? Operating since 1966 ? Total of 125Mt mined to date (2.43% Cu, 6.60% Zn) ? Current plan at 2.4Mt/Y (6575t/D) Current Practices ? Evaluating stope margins to ensure that value is added ? Scheduling sulphide and Cu stringer ore to limit oxidation in passes ? Scheduling to maintain uniform grades to concentrator ? (SOPs highlight problem stopes on mine plans, and limit blast sizes in those stopes which may contain sulphides prone to oxidation) ? Scheduling high-Pb stopes to avoid spikes to concentrator ? Providing weekly, monthly and long-term forecasts ? Reconciling mine and mill production ? Underground grade and dilution estimates by mine supervision ? Terminate mucking when grade becomes sub-economic ? Laser cavity surveys to provide feedback and improve Designs Cut-off Grades ? Ore value is obtained from copper, zinc and silver ? Ore outlines at 2% copper equivalent used to guide stope planning; sulphide outlines obtained from contacts while copper stringer outlines drawn from block model (kriged) ? Datamine block model and CADD software used to evaluate alternative stope shapes ? Stopes classified as waste, incremental, or full-cost based on margin calculations for each stope ? Incremental ore may be mined if it does not displace fullcost Ore Conclusions ? Grade control remains an important function for optimizing the ore extraction at Kidd ? The scope of the function has changed to a scheduling focus ? A change in grade control practices over time has not led to significant changes in concentrator feed ? The lead and iron sulphide content of the ore display upwards trends and may require more attention in the future ? The key function of field observations has shifted to flagging exceptions and terminate mucking at grade cut-off

May 1, 2003

By MKS Vel, S. Mukhopadhyay, R. Mishra

Off late, the criteria of selecting the refractory have acquired a trend line aiming to a cleaner environment and the utmost importance is given to the eco-friendly approach. The stainless steel making furnaces normally use mag-chrome refractories for the obvious reasons of changing slag basicity from acidic to basic. Such refractories generate toxic fumes and compounds with hexavalent chrome, which is unhygienic if inhaled. The present paper describes the development of a chrome free alumina magnesia carbon refractory, it's different test properties, simulative testing and microstructures. The optimum quantity and distribution of carbon in the brick restricts the carbon pick-up by the steel. Bricks with the same composition were manufactured in the commercial scale and used in a stainless steel making furnaces in USA. The performance of same refractory in this furnace was quite encouraging and at present the same quality brick has become a normal practice in this furnace. Since no chromite is used in making this brick, so no toxic compounds are generated environment remains pollution free.

Jan 1, 2004

By D. A. Akinlade, N. L. Richards, D. C. Murray, W. F. Caley

To investigate the effect of adding Ti to a Ni-Cr-Fe powder metallurgy alloy, a thermodynamic software package was used to predict the phase transformations that occurred during thermal processing. Specifically, the effect of adding 3w/o Ti to a 6w/o Al modified ternary Ni-Cr-Fe alloy (the quaternary) was simulated and the phase transformations that might occur in the material on sintering were obtained using the thermodynamic modeling tool. These predictions were subsequently compared with experimental results obtained by X-ray diffraction and metallography. For comparison, selected compacts were prepared containing only the ternary + 3w/o Ti (no Al). Based upon compressibility curves, the optimum pressure for producing the new Ti compacts was 500 MPa vs 600 MPa for the quaternary composition with Ti. In each case, hardness of the base alloy was enhanced by the Ti addition whereas the residual porosity remained relatively constant at about 19%. Finally, although SEM/EDS failed to confirm the presence of Ti in the gamma prime intermetallic, XRD spectra showed a shift in lattice parameter on addition of Ti, suggesting that the intermetallic was of the form Ni3(Al,Ti).

Jan 1, 2010

By F. N. Smith

Corrosion was observed on the aluminum pressure plates and dress-caps that hold the glazing in place on a curtain-walled building, The multi-storey building in question is situated in the downtown area of a busy Canadian city, For aesthetic reasons, the original design required the dress-caps (which have L-shaped cross-sections) to be externally clad with thin copper sheet. Since the aluminum was in direct contact with the copper trim, galvanic corrosion developed that resulted in damage to the aluminum components, Soluble corrosion products washing off the copper trim may also have contributed to the accelerated corrosion of the aluminum, The aluminum pressure plates and dress-caps are being systematically replaced with components made of fibre-reinforced plastic. The outsides of these new components will be clad with thin copper sheet in order to preserve the original appearance of the building.

Jan 1, 2005

By Mary Jean Buchanan

The last twenty years have seen the advent of environmental concerns and sustainable development, and the industry has witnessed the rise of Environmental Management Systems and their registration through several international standardization systems such as EMAS and ISO 14001. Beyond EMS and ISO 14001, which new goal the mining industry should aim at. Life-cycle assessment (LCA), another tool from the Environmental Management System series, is also on the rise and currently the object of an international standard (ISO 14040:1997). Through LCA, it is possible to assess the environmental aspects and potential impacts associated with products and services, taking into account all the activities required for its fabrication, its use, its transportation and its disposal. How could LCA be applied to the mining industry ? Is the international market pressurizing on mining companies to supply an ?environmental ore?? What about the automobile industry and its use of LCA ? Will it influence the ferrous and non-ferrous metal industry, suppliers of raw materials ? This paper presents a review of possible applications of LCA for the mining industry as well as world trends.

May 1, 2001

By P. E. Weidmark

"Energy, Mines and Resources Canada has published the first in a new series of reports that will examine selected mineral products that are imported.""Vanadium - An Imported Mineral Commodity"" looks at one of the 32 raw materials for which Canada currently is totally dependent on foreign sources of supply. Vanadium is used in Canada mainly as an alloying element in the manufacture of high-strength, low-alloy (HSLA) steels.The series will examine the supply systems for various selected imported non-fuel minerals, as an aid to developing policies that might lead to reduced dependence on external sources. Each report in the series will address a numberof questions:What countries do the mineral and its principal sub-products come from?How do they get to Canada?What are they used for?How vulnerable is the supply chain to disruption?Are there alternative sources?Are substitute materials available?In summary - how serious is Canada's supply problem for the mineral in question, and what should be done about it?Mineral Bulletin MR 188, ""Vanadium - An Imported Mineral Commodity"", is available for $3.00 ($3.60 outside Canada) from authorized government bookstore agents and many other bookstores, or by mail from the Canadian Government Publishing Centre, Hull, Quebec, KIA OS9."

Jan 1, 1981

By Jean-Guy L. Gauthier

"With the Ontario Ministry of the Environment stipulating that the cumulative concentration of copper, lead, zinc and nickel in mine mill effluent must be no greater than 1.0 milligram per litre, it has become necessary for the mining industry of find some form of treatment for the removal of heavy metals from effluent waters.To comply with these guidelines, it became necessary for Mattabi Mines Ltd., which is situated 50 miles Northeast of Ignace in Northwestern Ontario, to develop a compact, cost effective and technically sound treatment process to remove heavy metals from their tailings overflow. A design committee consisting of mine metallurgists, environmental engineers, a Dutch research and development team and the equipment supplier engineering staff was set up to accomplish this.Using some new and innovative wastewater treatment equipment, the guidelines established by the Ontario Ministry of the Environment can now be met. The sludge produced from the precipitated heavy metals is sent directly to the concentrator, thus eliminating the danger of re-dissolution of the metals in a landfill site, while recovering some of the valuable metals that would otherwise be wasted in a sludge landfill."

Jan 1, 1980

By R. K. Singhal

"On the mining side the Canadian oil sands industry has become proficient in excavation and disposal of ore and overburden. Nearly twenty years of mining experience is now behind this industry. While local improvements to existing mining systems and practices will continue, it is believed that some further gains in productivity can be achieved by selectively introducing new ideas from other mining and non-mining industries. This type of technology transfer is vital for over-all cost-effective technology enhancement of oil sands mining operations.Discussed in this paper are the issues of mining equipment, equipment sizing, microprocessor and computer based technol¬ogy as applied to mine-wide data management, automation and remote control and a projection of likely mining systems in the year 2000!This paper reviews the ""state-of-the-art"" in selected surface mining systems and attempts to evaluate the forthcoming technology and its application."

Jan 1, 1989

By K. Murase

Potentiostatic electrodeposition behavior of dendritic copper from acidic copper(I) chloride (cuprous chloride) baths containing sodium chloride and sodium bromide was investigated. The morphology, or appearance, of copper dendrite and the sodium content in the dendrite as an impurity were both influenced by deposition potential (0 to ?150 mV vs. SHE) and bath temperature (R.T. to 60 C), while the current efficiency for the deposition was 99% or more irrespective of the deposition conditions examined. The bath pH did not affect the deposition behavior in the pH range of 0 to 2. Bath temperature was found to be the most important factor influencing the deposition current. The current density of the dendrite deposition on a titanium cathode was lower than that onto a copper cathode with the same substrate surface area. The reproducibility of the current for the dendrite deposition was poorer when an as-polished titanium cathode was used, although it was improved by surface treatment of the cathode with an HF-HNO3-H3PO4 solution before electrodeposition. The deposition behaviors were discussed with the potential-pH diagram of the Cu-Cl-H2O system.

Jan 1, 2007

By A. J. DeArdo

Linepipe steels have come a long way in the past forty years. In fact, modern, high strength steels for large diameter linepipe applications represent one of the seminal accomplishments in metallurgy of the past half-century. The synergy of advanced steelmaking, alloy design including microalloying, hot rolling, and interrupted accelerated cooling has led to the marvelous steels being used today. The drive for higher performance pipelines has been motivated by the energy sector of our global economy who wanted both higher throughput capacity, i.e., larger diameters and higher pressures, and lower material cost, i.e., relatively thinner gauge wall thicknesses. These requirements led to new steels with higher strengths, better toughness and improved weldability. The goal of this paper is to trace the evolution of linepipe steels from the X60 grades of the small diameter pipelines of the 1960s to the (X80 - X120) grades used in the large diameter pipelines of today. The metallurgical triumphs permitting this success story, e.g., clean steel practices, controlled rolling, microalloying with Nb, and using IAC to obtain low temperature transformation products, will be highlighted and discussed.

Jan 1, 2005

By S. I. Saif

The Key Anacon deposit lies about 6 miles northeast of the Brunswick NO.6 mine of Brunswick Mining and Smelting Corporation. Geological mapping, especially in the well-exposed Nepisiguit River section, geophysical data, and information from extensive underground and some surface drilling show that the rocks at Key Anacon are similar in many aspects of stratigraphy and structure to those of the Brunswick Mine area. They include narrow beds of fine acid volcanic material interpreted to be metatuff and volcanogenic metasediments. The massive sulphide ore body at Key Anacon lies immediately above these acidic rocks, in association with other chloritic, sideritic or magnetic iron-rich metasediments. The iron formation, which is similar to that associated with other orebodies in the district, is overlain by massive andesitic material. Four phases of structural deformation have been recognized in the Key Anacon area; they are similar in intensity and style to those of the Brunswick No. 6 mine area. The orebody lies in a zone of complex isoclinal folding along the flank of a major F2 fold (Key Anacon Syncline) and in general appears to be stratiform. The ore occurs in probable F2 parasitic folds, and this suggests a complicated structural geometry superimposed on the original beds. The general similarity of the mineralization at Key Anacon, together with its occurrence with other iron-rich metasediments between a footwall of acid volcanic material and overlying andesitic rocks, is suggestive of stratigraphic time-equivalence with the Brunswick zone . If so, the metavolcanics at Key Anacon might have been derived either from a center within the main volcanic pile to the west or from a smaller local center active at the same time. Alternatively, the Key Anacon ore could have been formed during a much older volcanic cycle. The solution to this aspect of the problem is the subject of a continuing study.

Jan 1, 1978