Search Documents

By J. C. Hampton, L. A. Matzar, C. R. Gamwell

In geomechanics, conducting uniaxial or triaxial compression tests require samples to be prepared to a certain length-to-diameter ratio. This ratio is typically defined as 2:1 (length to diameter) and is accepted as a common standard for all materials on which mechanical properties testing is performed. Variations in sample length can cause changes in measured strength properties across multiple material types, such as cement, rock, or soil. Within the oil and gas industry, it is not uncommon to receive samples for technical services work that are slightly under or exactly the length requirement before surface grinding and sample preparation. Many of these samples are discarded from uniaxial and triaxial compression tests and used in another manner; therefore, it is necessary to study the length-to-diameter ratio in efforts to understand the limits and validity of testing samples that are slightly out of the 2:1 ratio. This paper discusses uniaxial compression tests performed using Berea sandstone and a standard cement mixture of 2.54-cm diameter to study changes in rock strength and properties. Compressive strength for each lengthto- diameter ratio over a range of 0.5:1 to 2.2:1 was measured. The investigation was extended to study near-end effects, where the sample length is near, but not exactly twice the diameter. It was discovered that the cement samples conformed reasonably well to the suggested ASTM correction factors. The sandstone did not conform to the correction factors and further analysis is required to develop a correction factor unique to the material. Near end effects, in both the cement and Berea, were found to increase compressive strengths, especially when the L/D of the samples was increased slightly over a 2:1 L/D.

Jan 1, 2015

By Dennis Martin

What is Borehole Hoisting Borehole Hoisting is the use of a hoisting plant to hoist rock, workers and materials or both, vertically through a borehole, between a mine level and surface or between two levels of an underground mine. Screen and bolt ground support on walls of 5.5 m diameter borehole hoisting shaft

May 1, 2013

By G. Riveros

A new, continuous fire refining process for copper has been developed and tested at the 5 tph pilot scale. During oxidation, the blister copper flows through a packed bed of crushed refractory bricks counter-current to a hot oxygen containing gas. The resulting desulphurized copper flows then directly into a packed bed of charcoal for deoxidation. By controlling the air to natural gas ratio, both temperature and reducing conditions can be controlled. Based on extensive laboratory scale measurements of the rate of copper oxidation and reduction, the process concept was developed aided by process modeling and simulation. The industrial-pilot scale installation built at the ENAMI Paipote smelter in Chile, consists of two cylindrical, compact reactors, operating in line, with a designed capacity of 5 t/h of blister copper. The results of the industrial-pilot tests confirmed the feasibility of the new process. The blister copper processing capacity was increased to 10 t/h with satisfactory sulphur removal. The degree of oxidation as well the copper temperature was controlled with relative ease. The specially designed siphon block allowed for smooth tapping of the oxidized copper and separation of refining slag. The reduction of oxidized copper in the packed bed of charcoal appeared to be very effective while control of the degree of reduction according to the height of the bed ensured control of the oxygen content in the refined copper at the required level.

Jan 1, 2007

By Geo. D. Furse

"The information that has accumulated regarding the geology of the McIntyre mine is the result of work by several geologists and, as might be anticipated, their conclusions have varied. The writer has been at the mine only a few years and due to wartime conditions has not been able to study and review the mine's geology as thoroughly as his predecessors. Where the writer's conclusions differ from those of previous authors, it should be noted that he has been unable to re-map all the workings in which flow contacts are exposed, but has endeavoured to describe the structure as indicated by the evidence he has been able to observe. He wishes to thank H. G. Skavlem and H. S. Robinson for their constructive criticism of this paper, and McIntyre Porcupine Mines, Limited, for permission to present it. A list of references is appended.The McIntyre mine is in the central part of the Pearl Lake section of the Porcupine gold area. It includes the ""bed of Pearl lake, twenty-two claims to the north of the lake, and the Platt Vet lot to the southeast. It is bordered on the west by the Hollinger and on the east by the Coniaurum property. The chief ore-bearing veins on the upper levels lie very close to the north shore of the lake, but some occur under the lake, and others of lesser importance are found to the southeast. The most important veins are Nos. 3, 5, 7, 10, and 25. Some of the veins extend into the Hollinger. on the west and others cross the east boundary into the Coniaurum. The total production since the commencement of milling in 1912 to the end of March 1947 has been $168,448,218 in gold and silver from the milling of 17,690,963 tons of ore."

Jan 1, 1954

By J. H. Baek, D. W. Lee, B. K. Kim

Nanostructured Cu-Al203 composite powders were synthesized by thermochemical process for an electrode application. The synthesis procedures are 1) preparation of precursor powder by spray drying of solution made from copper and aluminum nitrates, 2) heat treatments to evaporate volatile components in the precursor powder and synthesis of nanostructured CuO+Al2O3, and 3) CuO reduction by hydrogen into Cu. The suggested procedures stimulated the formation of the gamma-Al2O3. The mean particle size of the final composite powders was 20nm, and the electrical conductivity and hardness in the hot-extruded bulk were competitive with Cu/Al2O3 composite by the conventional internal oxidation process.

Jan 1, 2004

By J. W. Matousek

"Computer modeling of smelting processes requires internally consistent equations for calculating the compositions of mattes and slags. That is, the sum of the calculated assays must total 100%. One set of equations that satisfies this requirement for copper produced under oxidizing conditions (pSO2>one atmosphere pressure) is given by the following:%[Fe] = 62.0 – 0.775%[Cu]%[S] = 28.0 – 0.00125%[Cu]2%[O] = 10.0 – 0.225%[Cu] + 0.00125 %[Cu]2Mattes containing nickel in appreciable quantities do not have the defined “white metal” end point of approximately 80 percent copper and 20 percent sulphur that is found in the copper system during the converting process. The above equations, however, are readily extended to nickel and nickel/copper mattes for any desired end product composition."

Jan 1, 1996

By B. Das

"Computers have been used extensively in the mineral industry in exploration, reserves calculation, mining technology, mineral processing, etc. With respect to coal mining, there are also various applications for evaluating rock slope stability of open pits, design of open pits, underground operations, mine ventilation, ground control, data processing and management information, operations control and certain technological applications. Mine ventilation appears to be the field in underground coal mining touched on most; on the other hand, underground coal mining methods evaluation is represented only sparingly.It is therefore essential to review the status of the computer in underground coal mining methods evaluation in order to define its scope for further application. The paper discusses the roles of the mining engineer, programmer, computer operator and analyst as well as that of the computer. The important parameters will be identified and discussed along with their application for different underground coal mining methods, with their individual unit processes. Mainly, longwall face operations have been covered. Although many models have been of academic interest, they can be considered as important steps in a transition stage which will be followed by more practical applications for computers for underground coal mining method evaluations in the future. This calls for a coordinated effort from all concerned."

Jan 1, 1981

By F. Andrieux

"Extruded aluminum profiles are increasingly used for lightweight vehicle construction. Since fracture strains of aluminum profiles are relatively low, damage modeling is crucial for reliable crash simulation. For aluminum profiles, not only the stress state but also the orientation influenced both the deformation and damage behavior. For the material characterization smooth tensile tests were performed in six orientations, both stress-strain curves and r-values were registered. Moreover notched tensile and shear-tension tests were performed in three directions. Finally punch specimens were tested to investigate biaxial loading. Digital image correlation (DIC) analyses were performed to determine local strain values such as critical values at failure. Numerical investigations were conducted with the strain based damage model GISSMO, which is well suited and widely applied for crash simulation. For a strain based failure model the choice of the deformation model is crucial. Deformation models with increasing complexity were investigated to find the best compromise over all experiments. It was found that there is still a great requirement on development of a material model which describes the orientation dependence of the hardening behavior over all stress states in order to be able to use a strain based failure model reliably.INTRODUCTION Weight reduction is an important step for less energy consumption and as a consequence aluminium is increasingly used in automotive parts. An important field of application is the well-established aluminium extrusion which allows the realisation of quite complex shapes of profiles required for an innovative lightweight design with integrated functions. Typical applications are chassis parts, bumpers, crash elements, air bags, etc. Especially the Al–Mg–Si medium strength alloys of the 6000 series can be easily extruded to form complex profiles and prevail for extrusion. Since fracture strains of aluminum profiles are relatively low, damage modeling is crucial for reliable crash simulation. For aluminum profiles not only the influence of the stress state but also the orientation with respect to the extrusion direction have an influence on both the deformation and damage behavior and need to be characterized. The effect of orientation on deformation behavior has been intensively investigated in the last decades and material models haves been proposed (e.g. Barlat & Lian, 1989; Barlat, Lege, & Brem, 1991; Barlat et al., 2003) to describe accurately anisotropic behavior. However it can be noticed that the parameters of anisotropic material models often rely on the yield stress in different directions, which means that the effect of strain hardening is not automatically accounted for. The accuracy of the models at large deformation is not guaranteed and has to be verified. In contrast to deformation models both the characterisation and the modeling of anisotropic damage behavior are not systematically studied. Isotropic failure models based on a critical strain as function of stress triaxiality (ratio of the hydrostatic stress to von Mises equivalent stress) are widely used for crash application (e.g., Bai & Wierzbicki, 2010; Sun, Andrieux & Feucht, 2009; Sun et al., 2013). The mechanisms of failure are manifold and not fully understood; to develop an anisotropic failure model it is mandatory to also have experimental data in different orientations for loading scenarios other than uniaxial tension, e. g. shear, biaxial tension, which implies an extensive experiment plan. This makes the development of failure models more challenging than deformation models for which it is possible to develop a reasonable anisotropic model using the framework of yield function and calibrate the material parameters based on results of tensile tests in different directions. Moreover the development of deformation and failure models are intricate as the variables governing the damage evolution are predicted by the def"

Jan 1, 2018

By Zorigtkhuu Davaanyam, Fisher Wang, Bern Klein, Amit Kumar

"The High Pressure Grinding Roll (HPGR) is an increasingly popular energy efficient solution for comminution of competent ore deposits that primarily competes with conventional crushers and tumbling mills. A significant barrier to increased adoption of HPGRs is the requirement for large amounts (one tonne or more) of sample for pilot testing which may not be feasible for most early staged projects.Various researchers have worked towards developing piston-die and JK drop weight tests to model and predict the energy requirements for an HPGR. Two small scale laboratory test procedures (the SMC test (Morrell, 2009) and the piston press tests (Davaanyam, 2015)) have been developed in recent years to provide necessary information to size an HPGR.These two methods were used to estimate the required specific energy for an HPGR unit and compared to HPGR pilot scale test results from a copper deposit. The comparison provides insight into the benefits and limitations of these tests.INTRODUCTIONHigh pressure grinding rolls (HPGR) have gained popularity in recent years because of their energy efficiency in comminution. Various researchers have suggested that approximately 50–80% of the total energy consumed in a mineral processing plant is used by the comminution equipment (Haque, 1999; Abouzeid & Fuerstenau, 2009; Wang, 2013). Haque (1999) showed that the efficiency of grinding equipment can be as low as 1%. Due to the energy intensive nature of comminution, mining industry has been forced to explore alternative energy efficient processes.An HPGR based circuit has been shown to be 10–25% more energy efficient than a conventional SABC circuit (Von Michaelis, 2009; Wang, 2013). A significant barrier to the increased adaptation of HPGRs is the requirement for a large amount of sample for pilot testing (up to 5 tons), even on a prefeasibility level. Numerous studies have been performed to utilize piston press test to analyze the performance of the HPGR circuit and to predict the energy consumption for an industrial application. This paper uses two small scale laboratory test procedures, the SMC test and a piston press test, to compare the energy requirement to the pilot HPGR data."

Jan 1, 2016

By T. G. Joseph

ABSTRACT: The Canadian oil sands provide some of the harshest mining conditions in the world. Asoperations demand ever bigger tools, the toll on large mobile mining equipment is high, with structural life often half of that expected. Soft ground conditions predominantly lead to fatigue failure scenarios, poor stability, and inconsistent payload evaluations. These challenges are not solely a concern for Canadian oil sands mines; there are far-reaching implications for surface mining equipment in any poor ground-operating environment. This paper focuses on the basics of payload evaluation, motion response, and a simple estimate of structural life for haulers.

Jan 1, 2011

By Bhawani Singh, Mahendra Singh, N. K. C Samadhiya

"Inherently anisotropic rocks occur in abundance at many rock engineering project sites in Himalayan region. These rocks pose difficulty in analysis and design due to their direction dependent strength behaviour. Moreover the strength varies in a non-linear manner with confining pressure. Mohr- Coulomb strength criterion is widely used by geotechnical engineers for defining strength of rocks subjected to given confining pressure. However, the conventional Mohr-Coulomb (MC) criterion suffers from the limitation that the strength is treated to be linearly dependent on confining pressure. In the present article, the MC criterion has been modified by incorporating non-linear term while retaining the original parameters c and ?. The non-linearity with confining stress level has been imbibed through critical state concept (Barton, 1976). The criterion has been applied to a triaxial test data base comprising of more than 1140 triaxial tests conducted world-wide on anisotropic rocks. Statistical evaluation of the goodness of fit of the proposed criterion to the data-base has been carried out. Further the predictive capabilities have been evaluated by determining the error in estimation of triaxial strength if only few triaxial test data are available for determining the criterion parameters. The data base has also been back-analysed to assess the critical confining pressure for anisotropic rocks. Statistically the critical confining pressure, for the present criterion, may be taken nearly equal to 1.25?cmax, where ?cmax is the maximum value of the UCS out of all orientations of planes of anisotropy. It is concluded that reasonably good estimates of the anisotropic strength are possible through the proposed criterion.INTRODUCTIONMany rocks encountered in Himalayan region like shale, slate, schist and phyllite are inherently anisotropic and exhibit direction dependency in their strength behaviour. In addition, the strength of the rock also depends on the confining pressure and, the strength response is non-linear especially when the confining pressure may vary over large range. Conventionally, Mohr-Coulomb criterion is the most widely used criterion for rocks. However, the limitation of this criterion in its present form is that the strength is treated to be linearly dependent on the confining pressure. The present study attempts to address the following two main objectives: i) Include nonlinear response in the Mohr-Coulomb criterion while retaining parameters c and In their original form; and ii) consider anisotropic response of the rock for a given confining pressure. A nonlinear strength criterion, which uses shear strength parameters c and as per Mohr-Coulomb criterion, has been suggested based on critical state concept for rocks."

Jan 1, 2015

By Ian Sherrell, Michael Pirie, Riddhika Jain

"Conventionally, direct reduced iron (DRI) mixed with char from rotary furnace discharge is cooled down before separating the char via magnetic separator. The DRI must then be reheated for further downstream processing (i.e. smelting). Outotec has developed the PyroMagTM specifically to conserve thermal energy during this separation process. DRI is cleaned by feeding hot particles directly after reduction onto a rotating surface just above a stationary magnet assembly. This allows hot feeding of the clean DRI to the downstream equipment which renders the entire process more energy efficient.Continuous testing of the PyroMagTM was performed to verify design and separation. Because the use of DRI/char was not practical for test use, the pilot plant testing was conducted using a magnetite/sand mixture heated up to and beyond the Curie temperature of magnetite. The separation was efficient for both cold and hot processing with recoveries varying from 98.6% to 99.74%. As expected, the recoveries decreased to as low as 83.99% as the temperature was increased beyond the curie temperature of magnetite (585°C). Long term separation was thermally efficient and sustainable.INTRODUCTIONMagnetic drum separators are widely used in the mineral processing industry. These low to high intensity magnetic separators are used to concentrate various magnetic material, such as iron ore, and less magnetic materials, such as ilmenite and garnet from silica and other contaminantsThere are multiple classes of magnetism based on the effect that each material displays while in and out of a magnetic field. In a simplified fashion, which is more appropriate for mineral processing, the magnetic susceptibility of a mineral is used to define it as being ferromagnetic, paramagnetic or nonmagnetic. In this respect, minerals with varying degree of magnetic susceptibility can be selectively separated with different types of magnetic separation equipment in different stages of a process flow sheet. The lower strength magnets are employed early in the process to remove highly magnetic fractions. Later stages utilize greater magnetic fields for capture of less magnetically susceptible material."

Jan 1, 2016

By Feng Tianran, Lu Shijie, Shen Zhengchang, Han Zhibin, Tan Ming

"As a kind of non-metallic material, high-purify quartz sand has been widely used in many fields. Flotation is a popular way to process quartz sand. But it is in difficult position for flotation to get high-purify quartz product due to large amount of coarse particles contained in the feed. In this paper, a design principle of special flotation cell for high-purify quartz sand has been put forward base on ore property analysis and laboratory test, and the pilot scale special flotation cell has been developed to meet the requirement of the quartz sand flotation process. The special flotation cell for high-purify quartz sand is featured by middle positioned impeller, false bottom and draft tube, which could decrease the rising distance of mineralized bubble and strengthen the circulation capacity of the lower part of the flotation cell. Hydrodynamic study indicates that high air dispersion degree and strong lower slurry circulation could be produced by pilot scale special flotation cell, which is helpful to create a suitable hydrodynamic environment for quartz sand processing.INTRODUCTIONNatural quartz is a non-metallic mineral, which is widely used as raw material in multiple industry process (Shifu, 2006). High purity quartz, especially containing more than 99.9% silicon dioxide, is characterized by high temperature resistance, small thermal expansion coefficient, highly insulating and so on. The demand of high purity quartz has been rising along with social and economic development, now high purity quartz is widely used in the field of photovoltaic industry, electronic information, communications and aerospace industry.Quartz is a kind of main rocking-forming minerals in the nature. There are seven genetic types, such as natural crystal, quartz sandstone, quartzite, vein quartz, konilite, natural siliceous sand, granite quartz (Baolei, Shuilin, & Dianchao, 2012). The natural crystal is primarily used as raw material to refine high purity quartz, but it is not available for two reasons. On the one hand, the natural crystal is extremely expensive and poor in resources reserves, which can not satisfy the need of large-scale industrial production. On the other hand, the chemical component of natural crystal is instability, it may lead to low stable product performance in large industrial applications, and it is also difficult to achieve raw materials standardization. Therefore, there are a lot of studies to search for other technological methods to obtain high purity quartz from other genetic quartz types."

Jan 1, 2016

By J. Huh

Recently, there is growing trend to build the high-rise and install curtain walls. Following this trend, we developed robot for building wall cleaning work, which moves along Built-in guide rail of building. Because it moves attached at building wall for cleaning work, it can be seriously affected by potential threats, like earthquake, strong wind, malfunction, and construction error of built-in guide rail. In order to cope with those threats actively, this paper presents the Fail-Safety system. The building wall cleaning robot consists of two moving system: The Horizontal Moving System which mainly do maintenance work, and The Vertical Climbing System which transport the horizontal moving system floor by floor. We apply the Fail-Safety system to these systems. The Fail-Safety system consists of sensors to detect external situation, and, with information of sensors, give instruction for what to do. This robot system is installed with four kinds of sensors: shock sensor, infrared ray sensor, laser sensor, magnetic sensor. First, shock sensor detects external shock during cleaning work. When shock sensor detects big shock, the robot returns to starting point to inspect how damaged it is. Second, infrared ray sensor detects damage of built-in guide rail. It is to prevent destruction of robot caused by moving along damaged rail. Third, laser sensor gives notice about where obstacle is. It is for robot to avoid crash with obstacle and decrease damage. Fourth, magnetic sensor detects magnetic points, which are installed in rail at regular intervals, and helps robot to find its position, based on location of magnetic points detected. If robot is damaged by external shock and its encoder, which gives information of location to it, is not working, magnetic sensor will give information of robot?s location to robot. And then, robot regulates its velocity depending on position of it, and safely returns to starting point. The Fail-Safety system in this paper is for building wall cleaning robot to sense external threats, and prevent getting worse. Applied to this active protection system, making safe environment of maintenance work is possible for robot system.

Aug 1, 2013

By Victor Rudenno

"Previous methods have employed statistical analysis to model future mineral resources. The method presented in this paper uses Zipj's Law to determine the size and grade of tin deposits still to be discovered. The law is applied independently to both known deposit tonnage and grades. A probability distribution for both 'tonnage and grade is computed/or those deposits still to be located and then, by applying a correlation between tonnage and grade, a distribution of the probability of metal content discovery is obtained.By considering an economic cut-off in metal contained in a deposit, the probability of economic success for the next tin discovery is computed, both for a world discovery and for the special case of Tasmania, Australia. The results indicate a probability of 11-37% on a world-wide basis and 18% chance of economic success in Tasmania.IntroductionIn the past , most attempts to determine the probability of success in finding an economic mineral deposit have relied on the accumulation of statistical data. These data are then used to predict a suitable frequency distribution to assess the probability of finding a deposit of a given size and grade (Singer,1975).The method not only relies on one having sufficient data, but also on the assumption that the data are not biased and that the distribution (usually log-normal) is a correct one. The method presented in this paper, to analyze tin deposits, uses Zipf's Law, which has been recently applied to oil, uranium, lead-zinc and gold deposits by Folinsbee (1977) and to Western Australian gold deposits by Rowlands and Sampey (1977). Tapp and Koniuszko (1978) have applied Zipf's Law to mineral distribution patterns in the Northern Australian orogenic provinces, which has enabled them to make predictions with a relatively small data source."

Jan 1, 1981

"Process specifications for classification system design f or closed circuit grinding are identified. A computer-assisted, mass balance procedure for estimation of material size distributions and required hydrocyclone separation performance is presented.GeneralClassification equipment application involves a large number of variables, but can be greatly simplified by consideration of the following two major steps:(A) Process analysis, in which the so lids and liquid material balances and solids size distributions in the three classifier streams are determined in order to establish the required classifier separation performance.(B) Equipment selection, in which the cyclone dimensions and feed conditions are selected to yield the de sired separation, and the number of units then determined by their capacity rating."

Jan 1, 1984

By V. Panayotov, M. Panayotova

"Finding a reliable relationship between fundamental properties of minerals of non-ferrous metals and their ability to float is extremely important. The approach presented in this work allows us to draw predictive models for an effective flotation, suitable choice of reagents regime and expected technological results before the minerals enter the flotation process. Attempts to adjust the technological regime in already begun flotation are often unsuccessful because the basic physicochemical processes have already taken place. Mineral processing can be optimized on the basis of objective and basic parameters, decisive for the efficiency of the process - the state of the surface of the mineral; assessment of: minerals flotation ability, the need to apply and the type of needed pretreatment, and expected technological results. The theoretical foundations of such an approach are presented in the work, as well as supporting them experimental results, and information on practical implementation in lead-zinc and copper-pyrite ores selection.INTRODUCTIONIncreasing impoverishment of ores of nonferrous metals incoming to the flotation and rising costs for obtaining the final product lead to the inevitable question - will the mineral processing process be beneficial economically, technologically feasible and environmentally safe and what is the way to improve its efficiency. Some of the possible solutions are already in practice - new more efficient and less energy consuming flotation machines and equipment, new - more efficient and selective reagents, new combinations of flotation regimens, and so on.Finding a reliable relationship between fundamental properties of minerals of non-ferrous metals (sulphides and oxides - most of them with semiconductor properties) and their ability to float is extremely important. This is the subject of research, started in the 60s of the previous century and continuing to the present day. Such dependence would enable a realistic assessment of flotation ability (flotability) of minerals before their flotation processing. The basic dependence, displayed by the researchers as Hoberg (1975), Chanturia and Shafeev (1977), Chanturia and Lunin (1983), etc., represents a relationship between bulk properties of minerals and their flotability, considering especially the concentration of the main charge carriers, namely electrons or holes. The bulk properties are practically constant for minerals from a given field. But the 'main arena' of the flotation process is actually the mineral surface (Carta, 1970; Rao, Labonte, & Finch, 1992; Panayotov, 1999; Rao, 2003; Hu, Sun & Wang, 2010). Therefore, we introduce a methodology for studying the surface of minerals, which methodology gives the degree of semiconductor bands bending on the surface and respectively - the charge of the mineral surface and its ability to interact with reagent-collector. The latter can be used to select the most optimal reagent for the corresponding mineral."

Jan 1, 2016

By W. F. J. Cosser

AN agreement having been arrived at in 1935 whereby McIntyre Porcupine Mines would purchase gravel for back-filling purposes from Hollinger Consolidated Gold Mines, the aerial gear as described below was installed. As originally discussed, the plan called for installation of a loading bin at the junction to the Hollinger tram, so making the McIntyre tram an entirely separate unit. The experience of the Hollinger engineers, however, went to prove that the operation of a bin (remote from sources of heat) should be avoided if possible, owing to the severe winter conditions (35° to 40° F. below zero).

Jan 1, 1938

By Robin Perry, Claude Bazin

"Discrete transfer functions which use the grinding circuit feed tonnage to predict mass flowrates at reagent addition points in a flotation circuit were calibrated using a dynamic grinding/flotation circuit simulator. Predicted mass flow values are multiplied by reagent addition ratios to obtain actual reagent flow. The transfer functions are currently integrated into the distributed control system of Les Mines Selbaie.IntroductionThe development of adequate tools for the control of flotation processes is a continuous challenge. Since the early 1970s there have been numerous publications dealing with practical aspect of control of flotation processes. Most plants use a combination of feedback and feedforward controls to reduce the effect of the following flotation process disturbances (McKee, 1991):• changes in throughput;• changes in feed grade;• changes in particle floatability (size, liberation, surface oxidation ... ); and • deliberate changes of setpoint;Feedforward control manipulates variables such as reagent and/or air flow rate to attenuate the effect of disturbances such as changes of feed rate and mineral content. The feed forward strategy is driven by measurements of these disturbances. Feedback control is used to maintain process variables to targeted set-points of concentrate or tails grades. The feedback control action is driven by deviation from the set-point, caused by a deliberate change of set-point or disturbances.This paper proposes a method to improve feed forward control schemes by the addition of a simple model for solids transportation. The feedforward strategy considered in this paper is the ratio type, in which the manipulated variable is changed according to a predefmed ratio between this variable and the measured disturbance. A typical example is the ratio of the reagent addition to mass flow of ore.The paper reviews the state of the art in feed forward control strategy applied to flotation processes and describes the method used for predicting mass flow rates. The last section shows an application of the method in the Les Mines Selbaie flotation circuit."

Jan 1, 1994

By R. Simard

"Conventional exploration strategies identify many mineral deposits as potentially interesting, although only a few of them turn out to be of economic importance. In the context of exploration for sulphide nickel deposits in the Canadian Shield, a decisional model, based on a statistical study of parameters relative to nickel deposits as well as to barren sulphide occurences, has been developed.Because such geophysical variables as gravimetry, aeromagnetism and topography could be related to the relative importance of nickel-bearing deposits, a statistical analysis of 13 such variables was carried out for 98 targets which were considered promising after conventional exploration. Among these 98 targets are36 sulphide nickel deposits in the Canadian Shield and 62 drill-tested non-economic occurrences. The results of this study led to the development of a linear logistic model that permits evaluation, for each of the targets, of the probability of finding a nickel deposit of potential commercial interest. This decisional model can thus complement conventional exploration strategies.RésuméLes stratégies conventionnelles d'exploration définissent un très grand nombre de cibles comportant un inténet minier potentiel dont seules quelques-unes correspondent à des gisements économiquement importants. Dans Ie cadre de l'exploration des dépôts nickélifères du Bouclier Canadien, nous avons défini un modelé de décision fonde sur l'étude statistique de divers paramètres relatifs tant aux gisements d'importance qu'aux cibles dites stériles.Ayant fait l'hypothèse que certaines variables géophysiques (gravimétrie, aéromagnétisme et topographie) peuvent suffire à fournir des indications sur l'importance relative d'un gisement nickélifère, nous avons entrepris l'analyse statistique de 13 variables évaluées sur un échantillon de 98 cibles considérées comme potentiellement intéressantes par les stratégies conventionnelles d'exploration. Ces 98 cibles se composent de 36 dépôt nickélifères d ‘importance recontrés sur tout Ie Bouclier Canadien et de 62 cibles stériles reconnues par forage. Nous avons défini à l'aide de ces données un modèle logistique linéaire. Ce dernier nous permet d'évaluer pour chacune des cibles les chances de trouver un gisement. Ce modèle de décision peut done s'inscrire comme outil complémentaire aux stratégies conventionnelles d ‘exploration."

Jan 1, 1980