Search Documents

By H. Henao, E. Kohnenkamp, L. Rojas

The slags generated in the copper conversion process are mainly composed of Cu2O-Fe2O3-SiO2 with the compounds CaO and Al2O3 in concentrations up to 10 wt%. The present work contributes to the knowledge of the conversion process, generating experimental data for the diagrams of phases Cu2O-Fe2O3- SiO2-Al2O3 and Cu2O-Fe2O3-SiO2-CaO. The experiments were carried out in a tubular furnace at temperatures of 1150°C and 1200°C under a condition of saturation with tridymite. Once the equilibrium was reached, the samples were fast quenched in water. The phases in the samples were observed in a Scanning Electron Microscope (SEM) and the elemental composition of the phases analyzed by means of Energy-dispersive X-ray spectroscopy (EDS) detectors. The addition of Al2O3 and CaO into the Cu2O-Fe2O3- SiO2 system resulted in an appreciable displacement of the liquidus lines, corresponding to an expansion of the liquid in the tridymite primary phase field. INTRODUCTION The conversion process of copper consists of oxidizing Fe and S present in mattes with 60 to 65wt% Cu (up to 16wt% Fe). This process is separated into two stages: 1- Slag blowing: Fe is oxidized, the addition of a flux such as SiO2 (silica) forms a second liquid phase called slag, this phase is removed from the furnace; 2-Copper blowing: in this stage, the matte with low concentration of Fe (<1% w/w) is again oxidized to remove S as SO2 in the exhaust gases. The product of these two processes is the formation of Copper Blister (> 98wt% Cu) (Schlesinger et al., 2011). Unlike the aforementioned conventional processes, in most Chilean smelters, conversion Peirce- Smith Furnaces are loaded with high copper matte (70–75wt% Cu) (Henao & Moyano, 2016). Due to the low concentration of iron in these matte (up to 5wt%), it is considered that separating the conversion process in two stages is neither operational nor environmentally convenient. Therefore, the process is carried out in a single stage (Pradena et al., 2006), generating a slag phase with a high percentage of Cu2O (wt%Cu>40).

Jan 1, 2019

By S. Harvey

The McArthur River deposit is a structurally-controlled unconformity-related uranium deposit. The mineralization is situated at the intersection of a pronounced fault zone, referred to as the P2 fault zone, and the unconformity between Paleoproterozoic Wollaston Group metasedimentary rock and Paleoproterozoic to Mesoproterozoic Athabasca Group. Mineralization is variably hosted within the Athabasca Group fault wedge and the faulted basement, consisting of twelve zones covering a strike length of 2,700 m. The main P2 fault zone consists of several reactivated foliation-parallel faults containing narrow seams of graphitic clay gouge that are separated by highly cleaved, graphitic wall rock. The mine grid east-dipping P2 fault zone is characterized by reverse offset of the unconformity surface. It varies from a single discrete fault to splay offsets consisting of two to three individual splays. The combined vertical offset along the P2 fault zone is a maximum of about 80 m. The fault has emplaced a wedge-shaped sequence of Wollaston Group metasedimentary rocks into the Athabasca Group. Foliation-oblique faults occur throughout the McArthur deposit trend. Steep east-northeast trending faults generally exhibit apparent oblique dextral sense of shear. Less common, and possibly conjugate, are steep faults trending east-southeast with an apparent sinistral sense of shear. Offsets are generally less than 10 m on these structures. South-trending and shallow west-dipping brittle faults with offsets less than 1 m are also observed while rare steep, north-trending faults are also noted locally and played a critical role in development of the Zone 2 basement-hosted mineralization.

Jan 1, 2020

By Alan S. Lock

Large scale feasibility studies for the establishment of oil-seed and cellulose producing crops on mine tailings have been successfully conducted over 1 growing season with the purpose of these crops to be used as feedstock to the biofuels industry. An acid sulphide tailings impoundment in Copper Cliff, Ontario and a near neutral pH goldmine tailings impoundment in Timmins, Ontario were both tested by amending half hectare plots to approximately 1 m thick with residual biosolids from the pulp and paper industry and growing canola and corn on these plots. Full scale agricultural equipment was used to cultivate seed and harvest the plots to prove the full scale feasibility of farming on these biosolids. The vegetation development, growth, yield, quality and composition were assessed to identify the best species that would maximize biomass development for feedstock to the biofuels industry and carbon credits for the mining industry. Groundwater, biosolids and tailings chemistries were investigated to identify potential deleterious impacts of degrading organic matter on tailings metal mobility. Preliminary hydrologic investigations using moisture sensor profiles elucidate potential conservation of water in amended plots. Tailings amended with biosolids have the potential to provide the mining industry with carbon credits and supply feedstock to this new industry while reclaiming brownfields to a new level, utilizing industrial and municipal organic waste material.

May 1, 2009

By Andrew Thrift

Overview ? Problem ? Research question ? Literature review ? Methodology ? Results ? Discussion and recommendations ? New developments Problem ? Increasingly higher expectations ? Inadequate consultation leads to conflict rather than collaboration ? Consultation practice is often weak on decision-making ? Influence of consultation on planning is Unclear Research question ? Are Structured Decision Processes (based on decision analysis) an effective methodology for involving stakeholders in consultative decisionmaking in the mining industry?

May 1, 2006

By A. Carbonari

In order to gain competitiveness and compete at a global level, construction companies should improve their efficiency. The problem is even more relevant in the construction field, whose work processes find it hard to evolve towards new automated methods and techniques in the management field. For that reason, this paper suggests how construction companies could apply new technologies to implement automated management of environmental hazards. Based on a survey regarding the environmental risks presently experienced in construction sites, noise and dust were considered two of the main hazards. So in this paper a networked system for real time remote monitoring of the spatial distribution of dust in construction sites was developed. Such a system would relieve builders from the commitment of on-site surveys, allowing for a continuous monitoring of the site conditions and of the real exposure of each worker and pass-by to the pollutants generated by construction works. The main system requirements considered are: easy to deploy, reliable, as accurate as needed to be able to send real-time warnings and store a good estimation of the real exposure to which involved people have been subject to. So far the research produced a prototypical hardware for dust monitoring made up of wireless sensors which can be easily deployed on site. The sensors were calibrated by means of laboratory tests, where their measurements were compared with those collected by means of highly accurate instruments, which were taken as a reference. Thanks to these experiments, calibration curves for the sensors were worked out, showing also the measurement range of the sensors.

Aug 1, 2013

By Jose A. Caceres

Mine planning and mineral processing optimization are usually treated as two unconnected problems, especially at open pit and panel caving mines where the cut-off grade is practically the only variable optimized and analyzed for in the planning proposes. Using existing planning tool, the output is a reserve consumption strategy privileging higher grades. With the earlier consumption of the highest grades, every year produces revenues which are closer to the cost and potentially even below cost. However, there are other ore characteristics that can also affect the profitability of the operation. A new methodology has been developed, incorporating the grinding and flotation relationship into the mining economic models for the simultaneous analysis and optimization of the throughput-work index-recovery relationship through changes in the mining limits, sequence and redefinition of the reserve consumption strategy. A mine-site that implements this new planning strategy, can expect to increase the NPV from 5 to 15% depending on the actual operational settings. Two case studies have been developed, showing how the inclusion of the work index in the economic model changes the phase and mining sequence in an open pit mine and the caving sequence and the optimum column height in a panel caving mine.

May 1, 2004

By Liu Liching, Yan Hongjiu

"In China, the electromagnetic induction initiating system f or blasting engineering has been greatly developed in recent years. With this system, the total number of detonators that may be blasted in each round has been increased from 420 to 940 as a result of the invention of a powerful exploder, and the length of leg wires of a detonator has reached 12 metres. These developments make the new system suitable for blasting engineering of medium scale. Another attractive feature of this system is a set of testing instruments which have been invented that enable a final check of the system to be made before firing as in normal electric blasting. This paper reports on these developments.IntroductionThe initiating system for blasting explosives is one of the key factors to the success of blasting engineering, along with the progress of explosives and blasting technology. Today, we have initiating systems which may be divided into two groups: electric and non-electric. The earliest initiating system was non-electric. Many mines, as well as many projects where rock excavation was involved, were blasting non-electrically before the new nonelectric initiating system came into use in the 1970s. Electric and non-electric initiating systems are the two main initiating systems which are now being widely used, each having its advantages and disadvantages. In electric blasting, the blasting supplies and the blasting circuit can be checked before it is used or fired and, therefore, is regarded to be more reliable. In many large-scale blasting engineering where reliability of the initiation is of great concern, a checkable initiating system is preferable. The electric initiating system is not considered to be as safe as the non-electric initiating system due to its inability to choose proper ignition energy. Therefore, a non-electrical initiating system would be preferable where a hazard of stray currents or static electric energy exists. At this stage of development, one would say it would be advantageous to develop a new initiating system."

Jan 1, 1988

By J. A. Brusset

Introduction The West Canadian Collieries, Limited, operate three bituminous coal mines in the Crowsnest Pass district of Alberta. Two seams are worked; their thickness varies from 10 to 20 feet and their pitch from 10 to 45 degrees. The Bellevue mine was opened in 1903, the Greenhill in 1914; both are gassy and dusty, and at both the haulage is a problem, as the workings are spread over distances of several miles. Compressed-air locomotives are used at Bellevue, rope-haulage at Greenhill, both of which solutions of the haulage problem are costly in installation an operation, and lack flexibility. In 1943, the Adanac mine was opened; and the question soon arose as to which system of haulage should be selected. Compressed-air locomotives and ropes were rejected on the ground of high cost. Since, under the Alberta Mines Act, the use of trolley locomotives underground in coal-seams is not permitted, the choice lay between storage battery locomotives and Diesel locomotives. The preference of the author, who had had experience with both in French gassy coal mines prior to 1930, was for Diesel locomotives, due to lower cost of installation and greater flexibility and reliability. However, Regulation No. 13 of the Mines Act of Alberta reads: &apos;No gasoline-driven engines shall be used underground in any mine, and no internal combustion engine shall be used underground in any coal mine, except only when authorized by the Chief Inspector in writing, and on such terms as he may prescribe"

Jan 1, 1948

By Shamia Hoque, Charles Q. Jia

Smelter slags contain valuable metals such as Co, Ni and Cu in proportions of less than 1 wt% along with about 40 wt% of Fe and 15 wt% of Si. Although aqueous SO2 is a versatile lixiviant for transition metals, dissolving the slag in aqueous SO2 produces solutions in which Co and Ni concentrations are lower than that of Fe due to the low metal/ Fe ratio in the slag. To develop the options for increasing Co and Ni concentrations the solubility of slag in aqueous SO2 was studied experimentally and theoretically using OLI, a software package for simulating electrolytes chemistry. The modeling results correlated well with experimental results. The model suggested that the species dominating the system was FeSO3, which would precipitate out as FeSO3.3H2O when the concentration of Fe+2 reached 1.22 molal and the concentration of S032- was beyond 1.4 molal. In the experiments the influence of pH and solids loading were studied. The leach solution obtained after dissolution of slag at 50% solids loading had a pH of 1.85. On raising the pH to 3, precipitation occurred. Analysis of the solution collected after the addition of alkali showed over 50% reduction of Fe, Co and Ni. XRD analysis revealed the precipitate to be of amorphous nature due to the silica present. The analysis confirmed that the precipitate was mainly FeSO3.3H2O. The paper also discusses the potential impact of the slag on the environment.

Jan 1, 2004

By John L. Rich

A New Field for the Mining Industry A new field for the mining industry is in prospect. This is the recovery of the petroleum which has been left in the ground in the older oil fields whose yield has declined until they are no longer profitable to operate in the ordinary way. The fact that an oil field has reached the economic limit for operation by pumping does not necessarily &apos;mean that the oil has ? been exhausted. In many such cases not over one-fifth, or even one-tenth, of the total oil content of the field may have been taken out when this stage has been reached. This means that there exists a large reserve of oil which can be recovered by whatever process best takes advantage of the natural conditions under which the oil occurs. Mine drainage is one of the processes by which this oil may be recovered. Its relative importance will depend partly on the ingenuity and wide-awakeness of mining engineers, and on mining capital. The opportunity is undoubtedly at hand. In order that we may be in a position to judge the possible advantages of mining methods for the recovery of this oil, I have reviewed, on the following pages, the methods now in use, and have discussed the physical conditions of the reservoir rocks in which the oil is found, and the suitability of the various recovery processes, in use or proposed, in the light of these reservoir conditions.

Jan 1, 1927

By E. Y. Carlson

"IN A SHORT PAPER it is impossible to do much more than to list the industrial minerals found in Saskatchewan and to give a brief description of the activity associated with each. I will not attempt to discuss the geology. It is sufficient to say that the settled part of the Province is covered by glacial drift which varies in thickness from a few feet to several hundreds of feet, and that this has hindered the search over much of the Province.CLAYA notable exception to this is the Cypress Hills area in the southwest corner which did not suffer any glacial action and where we find some of the large exposures of Cretaceous clays. In this area, the majority of the deposits are of stone-ware clays which are •an excellent raw material for such products as face brick and sewer pipe. Although the clay cannot be transported over any great distance it is used extensively in Alberta and Saskatchewan in the production of these products."

Jan 1, 1959

By Parsons. Robert B.

"Starting this year, corporations that conduct business in Ontario face a new tax a corporate minimum tax. This tax is in addition to the myriad of other taxes that make up a corporation&apos;s total tax burden including federal and provincial capital 1oXJ!S, payroll tax and sales taxes. Mining companies with gross revenues in excess of $10 million or total assets exceeding $5 million may be liable for this new tax. IntroductionOn December 8, 1993, the Ontario government introduced legislation to implement the corporate minimum tax (CMT promised in its May, 1993 budget. There are very few differences between the final legislation and the budget proposals.The CMT is effective for taxation years commencing after 1993. Subject to certain specific exemptions (detailed below), the tax applies to all corporations liable for Ontario Corporate Income Tax that have either gross revenues in excess of $10 million or total assets in excess of $5 million. These measurements apply to the aggregate gross revenues and total assets for all corporations in an associated group and a corporate partner&apos;s share of partnership assets and revenues must be included in the determination.In essence, the CMT is an income tax that is based on financial statement profit instead of an income amount that is determined separately under a statute. Accordingly mining companies (including so called ""junior"" exploration companies), which traditionally sheltered their taxable income by claiming generous exploration and development deductions, could find that they have a CMT liability."

Jan 1, 1994

By Christopher W. N. Anderson

Induced hyperaccumulation of gold by plants was first reported in 1998 by researchers from Massey University in New Zealand who proposed the idea of mining gold using plants (phytomining). Since that time research has been conducted to understand the conditions under which plants can be made to take up economic amounts of the metal. One key focus has been on the geochemistry of gold-rich soils, leading to a diagnostic test that can predict how suitable a particular soil might be to gold phytomining. Field trials have been conducted at several locations around the world in collaboration with industry partners. A Decision Support System has been developed to assist in the design and management of phytomining operations, and economic modeling has been carried out to set targets levels for phytomining technology. Novel studies are now examining the form of gold in plants. Research suggests that plants may store gold as discrete metallic nanoparticles in leaf and stem tissues, an observation that may lead to new ways to recover the metal from harvested biomass.

Oct 1, 2003

"The last thirty years have seen enormous changes in all aspects of the gold industry, from the technologies of mining and extracting gold to the role it has played in the fiscal policies of nations. In this time, the market price of gold has increased ten fold and mine production has more than doubled. However, the cost of mining and extracting gold has also increased exponentially, and the industry has struggled with declining ore grades and increasingly refractory ore bodies.With the major economic powers of the world shrugging off the uncertainties of the post cold war era and moving into a period of unprecedented political stability, economic growth and low inflation, gold is also losing its lustre as a hedge against inflation and a backing for national currencies. Consequently, countries that had accumulated and hoarded gold for decades are now disposing of these non-performing assets, resulting in major swings in supply of the metal. Fortunately, this has coincided with the end of communism in many parts of the world and a tentative move to free market economies in most of the developing nations. As a result, people are becoming wealthier, and this is creating more demand for gold, principally in the form of jewelry.On balance, the shift in the role of gold, from one in which a significant portion of new gold production lay dormant in bank vaults as insurance against political or fiscal instability, to one in which most new gold is now freely traded as an industrial commodity, responding to normal market forces of supply and demand, has had a negative impact on the price of gold over the last fifteen years. In that time, the gold price has declined from a peak of $850/oz in 1980 to an average price of about $400 through the rest of the l 980's, to a price of -$320/oz today (1997). In large measure, this has been due to the enormous inventory of gold metal that was held by central government banks in vaults around the world, and which has been dumped on the market as soon as the price has started to trend upwards. Even today, after ten years of fairly steady selling by central banks, about 3 0, 000 tons of gold (or -8 years' supply at the present rate of consumption) is still retained in vaults (Murray et al., 1997).The downward pressure on the price of gold has created exciting opportunities for the development and implementation of new technology. Increasing the efficiency of gold recovery from more and more refractory ore bodies, whilst at the same time lowering production costs, have become critical to survival in this industry. These challenges have been met by the development and implementation of new technologies such as heap leaching, carbon in pulp, resin in pulp and the sulphide ore pre-treatment process of pressure leaching, bacterial leaching and fluid bed roasting. For an industry that saw very little technological change in the first seventy years of the twentieth century, the pace of change over the last thirty years must have seemed bewildering at times."

Jan 1, 1998

By T. H. Adair

"IntroductionCONTINUOUS casting of ferrous and non-ferrous metals is not a new innovation. Patents describing machines for continuous casting are on file as far back as the year 1842. In the middle of the last century, Sir Henry Bessemer conceived and built a continuous casting• machine for the production of mild steel sheet.The production of billets and slabs of both non-ferrous and ferrous metals is being carried out by the continuous method on a fairly large scale on this continent and abroad. At present, the volume of production of •copper and aluminum and their alloys in billet and slab form is much greater than the continuous casting of steel products. The new installation of a continuous casting unit at Atlas Steels, Limited, is designed primarily for the casting of alloy steel billets and slabs.As an introduction to the art of continuous .casting of metals, it is interesting to examine a few of the many devices which have been developed. As previously mentioned, Sir Henry Bessemer constructed a machine for the direct casting of mild steel sheet. His discoveries and ideas of continuously casting steel formed the foundation for the work of other pioneers in this field, all of whom have contributed to the improvement of this art through the ensuing years. The machines which will be selected for examination are those of Bessemer, Poland-Lindner, Williams, Ennor, and Junghans. The last unit to be discussed will be a modification of the Junghans machine recently installed at Atlas Steels."

Jan 1, 1954

By Ralph L. Rutherford

Geologists or mining engineers familiar with geology are frequently requested by mine operators to give correlation in-formation regarding some mining property with respect to an adjacent area on one at some greater distance. It is the object of this article to mention a few of the difficulties involved in securing this information and to point out some of the salient factors upon which correlation is dependent. In view of the nature of the following discussion, a brief statement of the general character of coal formations .. seems appropriate. Coal formations, by reason of their environment of deposition which is in fresh or brackish water, exhibit the features common to continental deposits, in contrast to those of marine deposits. Such deposits are characterized by rapid variation in thickness and in lithological character both later-ally and vertically. (Plate 1 A). They consist essentially of sandstones and clay shales with all gradations between them, and also a few beds of coal and frequently some conglomerates.

Jan 1, 1924

By F. W. Crossland

Losses of metal are often traced to incorrect pH/ORP signals in flotation, leaching, extraction, electrolysis, and precipitation processes, aggravated by pressure changes. IC Controls, a Canadian mining sensor manufacturer, developed a new superior pH/ORP sensor that stops metal losses, reduces environmental footprint and contributes to sustainability. The cause of incorrect pH/ORP signal is rooted in the reference. Reference junctions are designed to allow diffusion of reference chloride ions into the process but also allow process ions to diffuse into the reference. This development is important to mines and hydrometallurgists where sulphide, cyanide, ammonia and other poisoning ions are present in the process. These ions react with reference electrolyte components causing the signal to change, drifting from the correct process value. With fluctuating process pressure, ion in migration dilutes the electrolyte producing similar signal drifts. If process ion in-diffusion could be stopped, the pH/ORP signal would be accurate. IC Controls new pH/ORP sensor stops process ion in-diffusion, and remains accurate over long periods. New processes using higher pressure and fluctuating pressurized reactors will greatly benefit from stable pH readings. Similar to IC Controls&apos; proven model 642 Mining pH sensor, our new model 647 contributes to sustainability through reducing disposal costs from waste reagents, lost metal and fewer used sensors.

Jan 1, 2014

By I. A. Kovalevska

Considered problems: elaboration and implementation of resource-saving technologies, low-cost support systems improvement, openings security and support, based on wallrock condition control with supreme implication into the rock pressure occurrence counteraction work. Results of analytic and underground investigations using computer simulation of the finite elements in order to calculate stressstrain state of the multivariable geomechanical systems are presented. Solutions of concrete objectives are found using spatial geomechanical model of solid motion around openings, considering real geomechanical parameters formation of support forms with proper conditions of their contact and real mechanical characteristics. Ultimate solutions of resource-saving technologies implementation based on the analysis of multivariate vertical, horizontal, and reduced stresses components calculation and also near-contour rock, support bearing components and security constructions movements are found. Results of experimental investigations of combined supports and security constructions, which increase openings&apos; stability in difficult conditions of flat coal seams are presented.

Aug 1, 2013

By V. L. Mitsopoulos

This paper provides a summary of tailings disposal techniques and the improvements that have been made through the introduction of thickened tailings disposal. The general properties and characteristics of thickened tailings are described, as is a design process for selecting appropriate technologies for thickening, pumping, transporting and storing tailings. The factors affecting the selection of an appropriate disposal site and operational considerations for the effective utilisation of tailings storage areas are also documented.

Jan 1, 2006

By T. T. Chen, J. E. Dutrizac, G. Poirier

In the Waelz kiln process, EAF dust is converted to an Fe-rich slag, a (Zn, Fe)-rich dust that is recycled to the kiln and the Zn-rich Waelz oxide which is subsequently up-graded for the recovery of zinc. To clarify the reactions occurring, the Waelz kiln products from a European Waelz plant were characterized mineralogically to determine the mineral species present, their micro-textures and the metal carriers. The EAF dust contains 27 % Zn, and consists mainly of ZnFe2O4 and ZnO, together with minor to trace amounts of NaCl, PbCl2, KCl, CaO, Ca2Fe2O5, Fe203, FRO, Pb oxide and various Ca-Fe-Al-Mn silicates. The KCI and NaCI sometimes agglomerate the other particles. The slag consists of nodules which often exhibit colloform structures. The slag contains of variable amounts of Fe, FeO(OH), FeO, gypsum, Ca(OH)2, Ca2SiO4 and various Ca-Fe¬Al-Mg-Mn silicates as well as minor to trace amounts of ZnFe2O4, Cr-Fe oxide, Mn-Fe oxide and other species. The Waelz oxide contains 57-61 % Zn, and consists predominantly of ZnO, with minor to trace amounts of KCI NaCl, Pb(OH)Cl, Pb20(SO4), Pb chloride, ZnSO4, ZnFe2O4, Ca2SiO4, Ca2Fe2O5, Ca-Fe silicate and NaZn4(SO4)(OH)6Cl.6H2O. The KCI agglomerates the other particles in the Waelz oxide. The recycled dust appears to be a mixture of EAF dust and Waelz oxide, but it contains relatively more coarser-grained metallic Pb and Pb oxide particles.

Jan 1, 2004