Search Documents

By T. Gerritsen, C. Martinez, F. Stober, T Ma, J. R. Frias, M. Sedighy, J. Janzen

Electrode control systems regulate power by physically positioning electrodes. Due to the weight and inertia of the electrodes and hoist equipment, this is a relatively slow process where power fluctuations of less than a few seconds are not fully corrected. Nickel laterite AC furnaces operating in high voltage, shielded arc mode typically incur frequent power variations of approximately +/- 20% or more around the power set point. To provide enhanced power control, Hatch has recently supplied, at commercial scale, a thyristor-switched reactance system called an SPLC. The SPLC incorporates predictive control software to operate furnaces at the maximum transformer rating by reducing the large power swings experienced without the SPLC. The resulting higher average power enables higher production, without increasing transformer or power plant capacity. A 60 MW production version of the SPLC has been commissioned on Falconbridge Dominicana's laterite nickel furnace, yielding excellent results with a 3 to 1 reduction in power fluctuations.

Jan 1, 2005

By Eugene Larochelle

The serpentine of the Eastern Townships of Quebec is more or less seamed and impregnated with chrysotile asbestos, of which we note two types: the cross-fibre and the disseminated fibre. The cross-fibre type always appears in fibres or crystals arranged parallel to one another, and disposed at right angles to the walls of the matrix serpentine. The length of fibre of these veins, which run in every conceivable direction, even crossing ?one another, varies from microscopie dimensions to three and sometimes four and even five inches. It is the principal form of asbestos found in the serpentine of Thetford Mines, Black Lake, Coleraine, and Asbestos. The disseminated-fibre type, which is the main product of the serpentine of Broughton township, in which ate located the mines at East Broughton, does not form veins, but occurs in the serpentine without any definite arrangement. There is a difference in the toughness and hardness of the rock of the two types, the Broughton serpentine being softer than that at Thetford. The disseminated-fibre section of the serpentine belt is probably more regular in its content than is the cross-fibre section. Nevertheless, it contains no 'crude,' which is the most valuable of asbestos, and the fibre is usually shorter than the cross-fibre average.

Jan 1, 1928

By H. K. Taylor

"As a mining engineer with over 50 years' experience in underground operations and mine planning, I appreciate the enormous amount of work that went into the paper; and despite an imbalance between geology-geostatistics and the profit-earning actions of mining and treating (possibly because of sponsorship only by the Geological Society), I agree with probably 85% of the detail. But the paper fails to build on its own sound foundations and, like many predecessors, drifts instead into idealism. Even the starting quotation from the US SEC Form S-18 is little more than a platitude. An American consultant (l) has observed: ""an evaluation that accepts ore reserves as guaranteed because their definition meets SEC criteria is an invitation to disaster"".Idealism enshrines at least two myths that have bedevilled definition over the last several decades. The first is that the only purpose of 'ore reserves' is to promise successful new mines, and that 'ore reserves' must necessarily follow feasibility studies.In practice, the identification of what is likely to be mined if a mine is started must often be done on broad economics long before the feasibility study, and there may be only little later flexibility. The second myth is that there can be a perfect deposit with a simple exploration-appraisal-development sequence (the paper's Figure 2) against which all inferiors can be matched. If the field of definition be regarded as a pyramid, the quest for perfection and the imposition of rigid promises upon the terms 'ore' and 'reserves' drive definitions so near the apex (or the bottom right corner of Figure I, if preferred) that little is left to define. The process is reminiscent of the legendary super-medicine, the one so powerful that the patient had to be in perfect health to take it!"

Jan 1, 1992

By Chris Blain

"Abstract - Based upon an extensive database, this paper analyzes the record of modern mineral exploration success and establishes the 50-year trends in discovery. The record clearly shows that the overall discovery rate rose during the 1950s and 1960s, peaked in the 1980s, and fell during the 1980s and 1990s. By commodity and ore-type target, the pattern of discovery is not continuous. Typically, it is episodic as a series of waves with minor resurgence. The waves reflect the order of the so-called discovery booms, led by uranium, then nickel, and copper, polymetallic base metals and gold. With the possible exception of gold, the discovery booms appear to be independent of metal price, although favorable perceptions of the price outlook may well have initiated the boom or led resurgence. Although difficult to quantify, an emerging trend in modern discovery is the integration of several detection techniques into the search process. No doubt, this trend will continue as orebodies become more and more difficult to find. The record of the past two decades shows that greenfield discovery rates have progressively fallen even though the level of investment in exploration has risen to an all-time high. This trend reflects increasing discovery risk. Several factors are contributing to this trend. Perhaps the two most important are: (1) deteriorating economics as increasing real costs and decreasing real prices continue to raise the economic hurdles for minimum acceptable exploration targets, and (2) increasing exploration maturity in many search terrains, particularly those in the traditional regions of North America and Australasia. To succeed cost-effectively in this new environment of increasing discovery risk will require extraordinary creativity, innovation, and technical skill coupled with commercial discipline."

Jan 1, 2000

By José J. Suárez

Abstract: Globally, the mining industry is expected to face the following challenges through 2020: 1. Sustaining growth amidst fierce competition 2. Containing cost increases and managing through the cycle 3. Attracting and retaining talent 4. Managing environmental concerns and improving sustainability 5. Managing volatility risks in commodity markets Our experience and research reveals that the higher performing global miners are adopting many of the following strategies: (1) Adopt a Global, Agile Operating Model (2) Be the Developer of Choice (3) Drive Capital Efficiency (4) Be the Employer of Choice (5) Integrate the End-to-End Business Model (6) Move to the Virtual Mining Value Chain This paper/presentation will provide data obtained through research on five (5) challenges facing the mining industry, and on the six (6) strategies that high performing global miners are adopting.

May 1, 2013

By John A. Allan

The subject chosen for this paper is not a new one, but the subject matter is so extensive that something new can always be said .about it. We are just beginning to realize how little is actually known about the character of Alberta coal, except for a few general facts. The object of this paper is not to explain that our previous information, in whole or in part, on the coal resources of Alberta, has been incorrect, but rather to present some new facts obtained as a result of recent study in the field and in the laboratory. As field investigation continues the problem of determining the character of a coal seam for any great distance laterally becomes more and more complex. Our present knowledge of Alberta coal deposits should not be discussed before due reference is made to those great pioneers who blazed the trails for later geologists, by recording their observations on the general geology of Alberta. Geologists, to-day, particularly those of us who are striving, year after year, to unravel the mysteries of stratigraphy, palaeontology, and structure, in so far as these are related to the coal resources of Alberta, fully realize our indebtedness to those three trail-makers, Dawson, McConnell, and Tyrrell. Had these geologists not recorded their observations correctly, nor interpreted the broad geological facts contained in Nature's book, with still uncut pages, how much slower would have been the progress of our coal knowledge in the succeeding years. It is true that many of the interpretations given to observations by these pioneers have had to be changed as a result of closer studies, but we must also expect that the geological interpretation from present day observations will be changed by future workers, as Nature's book is read and re-read.

Jan 1, 1925

By G. A. Davidson, P. G. Williams

"New developments in centrifugal slurry pump technology are discussed in relation to their importance for improving pump operation and reliability.Experimental data obtained by measuring the velocity of liquid flows in a slurry pump casing using Laser Doppler Velocimetry are presented. This demonstrates the importance of selecting pumps with the proper hydraulic design to provide optimum efficiency, maximum part life and minimum operating cost.The paper also discusses the use of new wear resistant materials, such as ceramic/metal composites, which can significantly improve the life of parts exposed to abrasive media. The results of laboratory attrition tests are presented. IntroductionCentrifugal slurry pumps are of primary importance for the hydro transport of abrasive and corrosive media in the mineral processing industry. As for all process equipment, slurry pumps must be carefully selected and operated to provide optimal performance. To achieve this, it is necessary to select equipment which will provide efficient and reliable operation for the specific service conditions and incorporates the best materials available to obtain maximum parts life.Abrasive wear of liquid end components is the most important aspect that distinguishes the design and application of slurry pumps from other types of pumps. It is therefore necessary to have a fundamental understanding of the mechanical interaction between pump components and the media being handled, as this will impact significantly on hydraulic design, mechanical reliability and selection of wear resistant materials. Recent advances in computational approaches'» have greatly improved the prediction of wear rates in pump casings by facilitating the solution of complex equations which describe the wear mechanisms mathematically. In conjunction with this, new experimental techniques allow researchers to measure flow fields in pump casings using non-invasive devices such as Laser Doppler velocimeters."

Jan 1, 1992

By T. Yalcin

"This paper describes the development of a process flowsheet designed to provide high dewatering rates and to bring about savings in tailing disposal costs. The flowsheet comprises a hydrocyclone, a settling cone and a thickener arranged in closed circuit. The mill tailing, after pulp density adjustment, is fed to the hydrocyclone which yields two products. The underflow product is sent to the settling cone for further dewatering. The overflow product, together with the settling cone overflow, goes to the thickener which, with the aid of flocculants, gives a clear effluent and a relatively dilute underflow. The latter combines with the original mill tailing to form the hydrocyclone feed. Solids finally leave the system in the settling cone underflow which can reach pulp densities of up to 78%, making it suitable for direct disposal or for use as mine backfill.Some discussion is included for the selection and sizing of equipment required for this process. INTRODUCTIONDewatering is an essential process for the disposal of mill tailings which forms an added burden in milling practice, often with little or no return. It is, therefore, desirable to conduct this process as economically as possible. One way of reducing costs would be to increase the rate of dewatering so that savings can be made in the size of dewatering unit s which would lead to lower capital and operating expenditures.A common method of dewatering mill tailings is gravity sedimentation which is frequently carried out with the aid of flocculation. In most cases, flocculation greatly enhances the sedimentation process, but only until a pulp density of 50% to 55% is reached in the settled material.Centrifugal sedimentation in hydrocyclones can provide high pulp densities rapidly, but does not result in a clear effluent.This paper outlines a suitable combination of gravity and centrifugal sedimentations that results in an over-all high rate of dewatering. The system developed produces a material of high pulp density while at the same time giving clear effluent."

Jan 1, 1989

By Rae Simpson

"This paper provides insight into the elements of computerized maintenance systems and identifies some of the factors which influence their effectiveness. The paper describes what to expect in terms of benefits and problems, the nature of effective computerized maintenance systems, some of the systems available and a process for selecting a system for your organization.The paper will be of interest to mining company executives and maintenance or computer personnel who are involved with, or contemplating, the introduction of computerized maintenance systems.IntroductionIn the drive to improve profits in an increasingly competitive world, mining companies are now using some of the most sophisticated equipment available. The introduction of large and complex equipment such as drag lines, haul trucks, and high-capacity milling equipment has resulted in order-of magnitude improvements in productivity. However, this productivity is now, more than ever, dependent on the continued operation of the equipment. A prolonged breakdown of a critical component can have a significant effect on companies' bottom-line results. As more technologically sophisticated equipment is introduced, maintenance costs become an increasingly important factor for mining companies.Fortunately, sound modern management principles are being used more often in maintenance departments. Progressive maintenance managers are turning to computers to help manage the myriad of details associated with running a maintenance organization.Some maintenance departments in larger mining operations would find it difficult, if not impossible, to operate at current productivity levels without their computer systems. Unfortunately, some other companies gain very little from their computerized systems and would probably be better off without them.How can you be sure that computerized maintenance will improve the maintenance picture for your company? What benefits can you expect to achieve? How do you go about selecting a maintenance system for your organization? These are some of the questions facing industry managers and executives today. In the following sections, we will provide some guidelines and insights to help address these challenges."

Jan 1, 1988

By L. Xia, B. Hart, K. Douglas1, S. C. Chelgani

Development work to optimize a flotation flowsheet for rare earth element (REE) recovery is underway. The original approach used alkyl phosphates and phosphoric acid ester as collectors to concentrate REE minerals. To improve REE recovery, hydroxamates as alternative collectors were investigated. In this paper, micro flotation of REE minerals using salicylic, benzoyl and naphthoyl hydroxamates is reported. Unlike phosphonic collectors, slime removal does not show a significant effect on REE recovery when using hydroxamates as collectors. Among the three hydoxamates, the grade of La, Ce, and Nd for concentrates produced by salicylic hydroxamate is the highest. The recovery response with naphthoyl hydroxamate is similar to that of salicylic hydroxamate; good grades for La, Ce, and Nd, less effective for Nb, Y, and Zr. The data indicated an affinity by salicylic and naphthoyl hydroxamtes for LREE over the HREE minerals. In comparison, benzoyl hydroxamate indicated an affinity for Nb, Y, and Zr. Temperature effects on REE recovery were also studied. The grade and recovery of REEs generated by flotation using a mix of salicylic and benzoyl hydroxamates at room temperature was almost identical or even better relative to the recovery using naphthoyl hydroxamates at elevated temperature.

Jan 1, 2014

By A. Mellek, M. Pischtschan, M. Perrucci

ABB has received an order for one of the most challenging mill drive projects in its history. With one SAG mill and one ball mill to be added at an iron ore mine in Sweden, the customer’s plant managers wanted to have the most efficient solution for driving their mills but had the budget limitations typically faced by the majority of mining companies during periods of market downturn. To find the best balance between cost of acquisition and highest performance throughout the lifetime of the plant, ABB was selected to deploy a synchronized bypass solution, in which only one drive system is used for two different mills in series. However, being one of the first grinding mills in the world with such a solution was not the only challenge the ABB team faced: The inclusion of some mill application functions - e.g., frozen charge protection, automatic positioning and creeping mode - brought the demands on the engineers to another level. With only one frequency converter and one mill application controller available, the configuration logic and interlocks had to be meticulously designed and thoroughly tested to ensure a smooth and safe startup. The solution offers a footprint reduction and more operator flexibility at a reduced investment as each mill can be run in both directions, and wear on the mechanical components can be greatly reduced due to ABB’s premium ring-geared mill drive (RMD). This paper will describe the details of the project, the configuration developed and the tests performed to guarantee correct software functionality. Mill startup is scheduled for January 2016.

Jan 1, 2016

By Heidi Fauser

The aim of the project was the development of an electroforming process for the production of medical implants out of gold. To prove the applicability of this technology, tympanostomy tubes were chosen as demonstrators. These barbell-shaped tubes are usually produced mechanically; of silicone or, for higher therapeutic demands, of metal ? gilded silver or gilded stainless steel. Gold electroforming of the tubes as an alternative manufacturing process would reduce the expenditures for the mechanical preparation and lower the corrosion susceptibility significantly. To obtain electroformed gold tubes of the desired shape, the following steps are necessary: fabrication of a negative template by drilling holes with countersinks in an insulated aluminium sheet, electroforming process, removal of the aluminium by using a sodiumhydroxide solution. For the optimisation of the shape and surface quality of the tubes respectively the simplification of the manufacturing process, various parameters were tested, e.g. aluminium quality and sheet thickness, type of insulation layer, substrate processing, hydrodynamic conditions, type of electroforming electrolyte, electrodes position, etc. The manufactured tubes were characterised in view of thickness distribution, hardness, surface roughness and purity in comparison to mechanically produced reference tubes. From the results obtained during the project it can be concluded that electroforming processes can be easily adopted for the manufacture of medical implants. The time-consuming electroforming process is by far compensated by the simultaneous production of an arbitrary number of implants.

Oct 1, 2003

By Daniel L. Cluff

The Canadian mining industry needs to find viable alternatives to the conventional cemented pastefill/hydraulic methods of backfilling open stopes for underground mines located within a permafrost zone. The harsh environment and the isolated location of a mine north of 60° impose additional challenges to standard backfill methods and opportunities to the technological and operational issues related to the use of frozen fill. Underground open stoping mining methods require the placement of fill material to enable the controlled recovery of ore from secondary and tertiary stopes. The typical design of the fill material requires the specification of inert material, water and binder. The permafrost conditions provide the additional parameter of subzero temperatures for backfill design and process control. The paper presents the results of an experimental field study, using large size samples, to determine the strength capacity of frozen backfill. The experimental work was performed utilizing rockfill and tailings material with moisture content consisting of water and ice crystals. Preliminary results indicate that the mixture of rockfill, tailings and moisture, develops strength that meet the demanded requirements for open stoping. A thermal equilibrium modelling analysis is presented in the paper.

May 1, 2008

By James F. A. Hatley

Northern Saskatchewan comprises an area of about 350 000 km2 and boasts some of the world's largest known high-grade uranium deposits. The successful mining of these deposits, however, can not be accomplished without overcoming technical challenges. Not only is the high grade of the uranium ore challenging, but mining methods need to be developed to deal with groundwater at very high pressures, and ground conditions that vary substantially from excellent to wholly unconsolidated clays and sand. This paper discusses the various mechanisms of inflows at the three of the Cameco Corporation Mines in Northern Saskatchewan. The risk of inflows is quantified in terms of unique challenges from hydrogeologic conditions, rockmass integrity, and uncertainty in geologic conditions. Mitigation strategies in case of an inflow are also briefly described. The paper concludes by addressing the impact of institutional rules (corporate standards) on minimizing, monitoring, and controlling the probability and/or impact of unexpected inflows.

Aug 1, 2010

By G. Dubé, A. Leclerc, P. Quinn, G. E. Agar, J. Y. Clouthiér, J. D. McLaughlin

"Gold dissolution by cyanide requires the presence of oxygen which is usually supplied by sparging compressed air into the gold containing slurry. For those ores that contain certain obnoxious substances that consume oxygen, maintaining the required minimum level of dissolved oxygen can be troublesome. One of the most economical solutions to the problem of low dissolved oxygen, especially in plants that have air compressors installed, is to enhance the rate of oxygen mass transfer.The oxygen mass transfer rate was measured in a two phase system using two different sparger arrangements, and with addition of a frother that is known to reduce the bubble size produced by the sparger. The common sparger system was shown to be inefficient compared to a readily available but under utilized method of gas dispersion which introduces air directly below the reactor turbine. Transfer of this technology to an operating plant confirmed the beneficial effect of the improved sparger system. The addition of the frother did decrease the bubble size, but it also reduced the oxygen mass transfer rate."

Jan 1, 1993

By Jorge M. C. Soares

The CO oxidation reaction has been studied on Au/TiO2 catalysts prepared by incipient wetness (IW) and deposition-precipitation (DP) methods. Additionally the assessment of activity was also conducted on simple gold compounds (Au2O3 and Au(OH)3) and their physical mixtures with TiO2. We have found that there are three types of CO2 production from fresh catalysts, which are only dried, namely: Non-catalytic Type I (low temperature CO2 production); Non-catalytic Type II (higher temperature CO2 production) and Catalytic Type III. The DP catalysts are far more active for Type III reaction, showing activity already at room temperature, whereas the IW catalysts generally do not show steady state conversion until T>673 K. This is due to both large particle size and the presence of residual chlorine for the latter. No truly catalytic activity was found for low temperature CO oxidation on gold precursors on their own, although both Au2O3 and Au(OH)3 react well with CO even at room temperature in an irreversible manner (Type I reaction). Despite that, catalytic activity was obtained by mixing Au(OH)3 or Au2O3 with TiO2 which gives further emphasis on the importance of a good contact gold/support and the absence of chlorine.

Oct 1, 2003

By I. Farr, P. Quinn, H. Mani

"Difficulties in the flotation of Inca's ultramafic ores at the Thompson Mill are related to the presence of serpentine slimes and some floatable rock minerals. Serpentine slime coatings depress pentlandite recovery while rock flotation decreases concentrate grade. Carboxy methyl cellulose (CMG) has been shown to promote sulphide flotation and to reject floatable rock.To improve ultramafic ore flotation, CMC addition in the rougher stage was studied in a laboratory scale column. Batch tests were conducted in the lab and followed up with continuous testwork at the Thompson mill. At 0.5-1.0 g CMG per kg ore, pentlandite recovery is increased by 5-10% in rougher flotation, pentlandite/rock selectivity is improved and pentlandite/pyrrhotite selectivity is unaffected.IntroductionAt Inca's Manitoba Division, two distinctly different sulphide ores are processed at the Thompson Mill, primarily by froth flotation. The sulfide ores are contained within the Thompson Nickel Belt and currently there are two operating mines, Thompson and Birchtree. Sulphide mineralization in both mines is simple, consisting of pyrrhotite (both monoclinic and hexagonal), pentlandite, and minor chalcopyrite. Both deposits are hosted by metasedimentary and metavolcanic rocks with variable ultramafic rock associations. Ultramafic rocks are mostly serpentinites: magnesium rich rocks composed predominately of serpentine. There is little serpentinite at the Thompson mine, while mineralization at Birchtree is closely associated with significant ultramafic rocks.Excellent recoveries of pentlandite (Pn) and chalcopyrite (Cp) are achieved at the Thompson Mill when processing ore from the Thompson mine. In treating the ultramafic associated Birchtree ore, nickel recoveries are some 6 to 8% below that achieved with Thompson ore. Furthermore, a typical concentrate from Birchtree ore contains more rock and is higher in MgO content. The presence of rock in the concentrate is related to free floatable rock species as well as rock locked with sulfides. The reason for the difference in flotation responses of these two ores has been the subject of on-going re-search."

Jan 1, 1998

By James R. Kuipers

Center for Science in Public Participation CSP2 ? Organized in 1997 to provide technical assistance to public interest groups on mining and water quality issues ? 80%of effort devoted to direct support of grassroots groups and tribal governments ? 20% of effort devoted to public-oriented education for public, tribal, state and federal regulators, and for industry ? Board represented by public interest groups, at large citizens, and academia ? Professional staff with experience from mining industry, academia and government ? website: www.csp2.org CSP2 Mission Statement The CENTER for SCIENCE in PUBLIC PARTICIPATION provides training and technical advice to grassroots groups on water pollution and natural resource development issues, especially those related to mining. CSP2 seeks to focus the debate on factual issues, as brought to light by its technical analyses, and whenever possible to seek consensus and win-win solutions. CSP2 also performs policy related work with federal and state regulatory agencies on the implementation of water quality, waste disposal, and mining reclamation regulations.

May 1, 2002

By A. V. Corlett

MR. C. S. Gibson: Mr. Chairman, I listened with much interest to Mr. Corlett's paper. Those of us who are directly engaged in mine ventilation and dust control are impressed by the improved atmospheric conditions to be derived from the use of methods of mining such as those in operation at Aldermac, which Mr. Corlett has just described, and those employed at Noranda. It is a well known fact that drilling-dust is one of the most potent factors in the production of silicosis in mines handling ores containing quartz, so that from that angle the use of diamond drills, instead of percussion drills, to drill ore for blasts in stopes is an important development. A second point which I think merits mention is blasting. Blasting, we all know, creates the most dust in a mine and the fact that you can drill ore for a large blast with diamond drills and fire it, say, on Saturday night, and then have all the next day to ventilate the workings, is a great advance in dust control. 1 have wondered if Mr. Corlett, or possibly those at Noranda, can en-vision the use of the diamond drill as a means of advancing cross-cuts and drifts, preparing stopes, etc. I believe it is a matter which is receiving considerable attention at the moment in some parts of the world and J thought it would be interesting to have Mr. Corlett's reaction on that point. MR. A. V. CORLETT: I am not quite so hopeful of using diamond drills as a means of drilling holes in the ordinary drift. Maybe some of the diamond drill men can give us some further information on that point. MR. R. D. LoNGYEAR: The diamond drill manufacturers are working on that problem, but until further work is done we have nothing definite to offer. Drilling holes with a diamond drill to compete with rock drills for advancing drifts and cross-cuts is a desirable objective, because of the elimination of drilling dust and the ability to cut a smooth bore of uniform diameter. To reach this objective, higher rates of penetration are required, which can only be achieved by discovering the optimum bit rotating speed, by reducing vibration, and by further improving the bits and machines. We are optimistic, but the problem is still largely in the research stage.

Jan 1, 1940

By Samuel Frimpong

Green house gases have become a major concern within the international community over the last two decades due to their potential link to global warming. Carbon dioxide (CO2) is the principal greenhouse gas. In the Kyoto Agreement, Canada has committed to reduce emissions by 6 % below 1990 levels by 2012. This presents a serious economic challenge to Canada and Alberta. Over the next decade, oil sands production expansion, population and industry growth and energy demand will increase CO2 emissions. Current and future CO2 emissions and their economic implications in Alberta will be critical in formulating a comprehensive and balanced policy for dealing with concerns in this area. Disposal of carbon dioxide (CO2) in land aquifers is a potentially viable option for Alberta in dealing with long-term CO2 emissions. Studies have confirmed the existence of appropriate aquifers in the Alberta Basin for CO2 storage over a long geological period. Carbon dioxide is an ideal candidate for aquifer disposal because of its high density and solubility in water at relatively high pressures. In this study, the authors develop a computer simulation model of a scaled aquifer disposal system. The scaled model consists of an injector well, aquifer environment with dominant Ca++ and Mg++ cations. Liquefied CO2 is injected at an appropriate pressure and concentration through an injector well model. The injected CO2 migrates from the point of contact between the injector well and the aquifer domain to the main regime of the latter. The rate of migration is a function of porosity, permeability, cations, aquifer fluid flow regime and CO2 injected pressure. These models are validated using flue gas data from the 546 MW Wabamum Power Plant in Alberta. The total energy requirements for aquifer CO2 disposal system are distributed between a minimum of 105 MW and a maximum of 172 MW, with a mean of 132 MW and a coefficient of variation of 10%. The results show that there is significant variability in all the energy requirements for the CO2 disposal system. The total energy requirements for the disposal system as a fraction of the total power generated by the Wabamum plant of 546 MW could be between 0.19 and 0.32. This is a very significant energy requirement and thorough analysis must be carried out to reduce this variability and energy requirements.

May 1, 2001