Search Documents

By K. J. Brouwer, J. P. Haile

"Construction of the first stage of the tailings disposal facility for the Montana Tunnels Project was completed in October 1986. The project is located 37 km south of Helena, Montana, and involves mining of42 million tons of weathered diatreme are at a rate or 13 500 tpd to produce a gold/silver dore, as well as lead and zinc concentrates. The tailings disposal facility for the project includes a fully drained tailings impoundment for storage of the tailings solids, and a process waterpond for storage of all decanted water prior to recyling to the mill. The over-all facility is designed to achieve the basic objectives ofminimizing seepage to the environment in the short- and longterm, and achieving a fully drained stable tailings mass suitable for immediate reclamation on completion of mining. Specific features of the design include a soil bentonite seal and drainage system within the tailings basin, a free draining embankment with a design flow-through capacity of 4000 US gpm and an ultimate height of 230 ft (70 m), and a soil bentonite lined make-up water pond with a capacity of 420 acre-feet (530 000 m'). The tailings will be discharged in a rotational sequence through multiple spigot offtakes to achieve a thin-layer low energy laminar flow. This 'sub-aerial' deposition results in higher stored densities and maximizes liquid-solid separation on the tailings beaches. The over-all design played a major role in the successful permitting of the project, and was significantly cheaper than a conventional wet disposal system, with overall unit costs for tailings disposal of less than US$0.36 per ton.This paper outlines the site characteristics and the tailings material properties and their influence on the design. Extensive use was made of naturally occurring free draining materials as well as bentonite modified soil liners within the tailings basin, embankment and retention ponds. General construction procedures for the various components are described, as well as on-going construction requirements utilizing materials from the open pit. Finally, the over-all costs and unit costs for tailings disposal are presented."

Jan 1, 1988

By L. A. Melis, A. R. Marchbank, S. A. Webster

"Certain northern Saskatchewan uranium ores have a high content of nickel and cobalt which offer the potential for recovery as a by-product to uranium. A nickel/cobalt recovery process has been developed as a viable method of recovering a marketable concentrate from typical uranium raffinate solution.Impurities are first removed from the raffinate and the pure solution is then treated with sodium carbonate to recover a bulk nickel/cobalt carbonate precipitate for sale to a primary nickel producer. All contaminants of concern are removed to very low levels and the product is free of radioactive contamination with gamma emissions significantly below natural background. Cost estimates have shown that installation of a nickel/cobalt recovery circuit within a uranium process plant is economically feasible.The testwork that led up to the selected process is described along with recommendations for further investigations such as additional testing of hydroxide precipitation as a possible viable alternative to carbonate. The selected process is described and project economics are briefly reviewed.PROCESS TEST PROGRAMBackgroundExtensive metallurgical research has been performed over the years to develop a process for recovering uranium from the Midwest deposit in northern Saskatchewan. During the course of this research, a certain amount of information became available which suggested that recovery of nickel and cobalt from uranium raffinate could be economically feasible. It was decided to undertake a test program which would investigate methods of separating nickel and cobalt from radioactive and other metal contamination to permit production of a saleable product.Available technology suggested that three general approaches could be taken to recover nickel and cobalt. The first and simplest approach would be to selectively precipitate the impurities of concern, primarily arsenic, iron and radium, and then recover a bulk concentrate from the purified raffinate. The second approach would be to purify the raffinate and then remove cobalt from solution by solvent extraction producing pure nickel and cobalt solutions for further treatment. The third approach would be to precipitate all metals from solution and then selectively re-dissolve nickel and cobalt in ammoniac solution which would be further treated by solvent extraction for nickel recovery, leaving cobalt for further treatment."

Jan 1, 1993

By A. J. Hyett, R. D. Reichert

"A laboratory and field research program was conducted to investigate the major factors influencing bond capacity of grouted cable bolts. The results indicate that cable bolt capacity most critically depends on the grout uniaxial compressive strength (UCS), the radial confinement, and the embedment length.In the laboratory &apos;split-pipe&apos; tests were conducted using P VC, aluminum and steel pipes to provide radial confinement, and field test sites were chosen in granite, limestone and shale rock masses. For both datasets higher capacities were obtained under conditions of higher radial confinement. A correlation between the two was obtained through a comparison of the radial wall stiffness of the laboratory pipes with that of the field boreholes as measured using a high pressure dilatometer. Cable bolt capacity was found to increase with embedment length though not in direct proportionality.The use of low water cement ratio grouts (<0.40) can increase cable bolt capacities by 50% to 75%. This effect is maximized under conditions of high radial confinement. However, the use of super thick grout paste (0.30 and less) may be both impractical and undesirable, first because of their limited pumpability and second because of their inconsistency in strength. Grouts with a water cement ratio of between 0.35 and 0.40 are recommended for practical cable bolt applications."

Jan 1, 1992

By John E. Udd

"Mining research at CANMET is delivered by the Mining Research Laboratories Division (MRL), with facilities in Sydney, Nova Scotia; Bells Comers, Elliot Lake, and Sudbury, Ontario; and Val d&apos;Or, Quebec. This paper gives an overview of the work of the Division as of early 1993. An addendum, at the end of this paper, describes the organizational changes that will take place in April 1994. IntroductionCANMET, the acronym for the Canada Centre for Mineral and Energy Technology, is the name by which the organization founded in 1907 as the federal Mines Branch is presently known. The name was changed in 1974, in order to give recognition to the importance of both minerals and energy technologies in the activities of the Branch. Further reorganizations have taken place since 1987. As a result of these, CANMET has assumed the status of a Sector (equivalent to the Geological Survey of Canada) and has been organized into four branches.The organization as a whole functions in an environment of semi-matrix management. Some of the ""line"" Divisions report to Directors-General for the appropriate branches while other, larger divisions, report directly to the Assistant Deputy Minister.The second dimension of the organizational matrix is composed of a number of ""staff&apos; divisions which report to the DirectorGeneral for Policy and Planning. Each of these Divisions performs a function which is common to all of the ""line"" divisions. For example, the Research Projects Office is responsible for monitoring the range of research activities of CANMET and for recommending allocations of funds for both research contracts and operating budgets. The Library and Documentation Services Division is responsible for CANMET publications and information services. Likewise, the Engineering and Technical Services Division provides support through, among other services, the construction of specialized laboratory equipment."

Jan 1, 1994

By C. Poon

For slope stability, knowledge of major and minor discontinuity sets that form the rock mass fabric is paramount for pit slope designs. Due to the increased awareness of health and safety in mining projects, efforts have been made to limit structural mapping in order to minimize the risk to personnel associated with approaching potentially unstable areas. Recognizing the importance of such safety precautions, Golder Associates Ltd. is applying a combination of techniques including 3D photogrammetry, conventional mapping and drilling with core orientation to enhance structural data collection. Photogrammetry uses digital photographs to produce a virtual model of a rock mass surface. The application of these techniques will be exemplified through an expansion design of an existing open pit. A comparison of stereonets obtained using these techniques showed some agreements, but also highlighted limitations of each method. The application of photogrammetry was found to be very useful in complementing the other existing techniques.

May 1, 2009

By J. G. Whellock, R. J. Phillips, J. W. Matousek, P. J. Marcantonio

"Stillwater Mining Company (SMC), a partnership of Chevron Resources and Manville Corporation, produces a copper-nickel, platinum-palladium flotation concentrate at its Nye, Montana mine. The concentrate is then toll processed in Europe. Recognizing the economic advantage of treating the concentrates at the mine site and of retaining this strategic resource in the United States, the Company commissioned Tolltreck International Limited and International Process Research Corporation to conduct pilot scale smelting tests with a flowsheet that would maximize metal recoveries while satisfying the environmental requirements of operations at Stillwater.Primary smelting was conducted in a single phase, 50 k W, submerged-arc, electric furnace. Refining the product mattes to copper-nickel ""white-metal""; containing approximately 2% iron, was accomplished in a Tolltreck, IV-litre, top blown rotary converter. Over-all platinum and palladium recoveries were approximately 99%; copper and nickel recoveries averaged 94%. INTRODUCTION(l-4)Stillwater Mining Company (SMC) a partnership of Chevron Resources and Manville, operates a copper-nickel, platinum palladium mine and concentrator at Nye, Montana, located in the valley of the Stillwater River, approximately, 100 km southwest of Billings. It is North America&apos;s only primary producer of these precious metals. The Stillwater area was mined for chrome ore during World War U and the Korean War, but it was not until 1961 that attention was drawn to the similarities between the Stillwater Complex and the Bushveld Complex of South Africa with its deposits of platinum group metals.A concentrated search for platinum was begun by Manville Corporation in 1967. Its presence, together with palladium, in mineable quantities was confirmed in the period 1976-1978, and the first partnership to develop the deposits was formed by Manville and Chevron in 1979. Anaconda joined the group in 1983, and in 1985 its share was purchased by Lac Minerals. In 1988 the interests of Lac Minerals were purchased by Chevron and Manville.The decision to develop the mine and build a concentrator was made in 1986. Construction began in the fall of that year, and the first concentrate was produced six months later, in March 1987. Underground mining is done in a two-shift, five day- week operation. Since startup, the concentrator has operated on a 24 hour/day, 7 day/week schedule, treating an average of 635 tonnes of ore per day and producing approximately 10 tonnes of concentrate."

Jan 1, 1989

By Douglas A. Karvonen

"Competition in the world potash market has increased significantly since the late 1970s. The failure of consumption to grow at expected levels has led to industry over-capacity, a situation which is likely to persist at least until 1990. Individual Saskatchewan producers and their offshore marketing company, Canpotex, have responded to this challenge by increasing mining efficiency, developing more cost-effective and reliable transportation systems and establishing innovative financing and market development programs tailored to customers&apos; special needs. Investment in warehouse facilities to serve U.S. customers and exploration of opportunities for intermodal distribution through the Great Lakes and the Mississippi River system have maintained individual producers&apos; position in the highly competitive domestic market.Export sales through Canpotex have been bolstered by utilization of CIDA funds, Exp ort Development Corporation financing guarantees and other innovative payment plans which enable heavily indebted developing countries to maintain the import levels which are necessary for their agricultural development.IntroductionPotash is the general term applied to various potassium salts both natural occurring and commercially derived. The most common of the commercial product s are potassium chloride, potassium sulphate and potassium magnesium sulphate. The potassium content of potash is measured in units of K20 equivalent. The common grades of potassium chloride produced for agriculture average at least 60 0/0 K20 compared with approximately 50% Kp for potassium sulphate and 22% for potassium magnesium sulphate."

Jan 1, 1985

By V. G. Papangelakis, I. Guzman, S. J. Thorpe

Pressure oxidation (POX) leaching has been commercially applied to refractory gold ores since the 1980s. In the process, sulphide material is oxidized and dissolved in order to release the gold encapsulated in the sulphide matrix, making the gold available for further recovery. Redox potential is a significant parameter during POX, however it is only measured ex-situ at atmospheric conditions. In-situ redox potential measurement would provide instant information that allowing adjusting the process parameters accordingly. In the present study, redox potential measurements were performed during POX of sulphide material at high temperatures and high pressures. The working electrode was an Ir electrode combined with a flow-through reference electrode in a novel and robust configuration. Experiments were performed in a 2 L titanium autoclave, at 200–220°C, 50–110 psi oxygen overpressure, and 10–30% solids mass fraction. Temperature and oxygen pressure conditions were selected in order to reflect POX of refractory gold ores. Results show that the Ir electrode is consistent with theory and is able to perform well under these conditions, showing promise as a new in-situ sensor.

Jan 1, 2017

By D. Moffat

Rio Algom Limited has mined uranium at Elliot Lake, Ontario for 20 years. The production of this energy-generating element results in the need to dispose of low-level radioactive solid wastes and liquid effluents. Because of the wet-temperate climate at Elliot Lake, the liquid effluents are of particular importance. Radium-226 is the isotope which requires most attention, and the current practice for its control is by addition of barium chloride and retention of the resultant precipitates in large settling ponds. Analyses of typical effluents and waste streams are discussed and typical levels of radium-226, thorium-230, thorium-232, thorium-228, lead-2iO, polonium-2iO, and uranium isotopes are presented.

Jan 1, 1979

By R. Frank Chiappetta, E. B. Wilson

"The maintenance records for AL-60 airlegs at Falconbridge Ltd. are used to demonstrate some of the procedures for the analysis of such data.The data are not representative of pure failure s of one type or another. In fact, the records are for the undefined pseudo-failures which are usually found in industrial operations. However, because the machines are brought to the shop only when inoperative, the individual recorded components are treated as failures. Manual calculations are conducted to show the analysis of variance (ANO VA) approach to determine whether certain data can be combined; only a limited number of the 206 machines being considered. The manual procedures continue with the weighting of the suspensions; i.e. terminations f or reasons other than the failure of the given component. After the data are sequenced in the proper order, the nature or pattern of the data is determined using the Kolmogorov-Smirnov (KS) test.It is recognized that these manual examples must be replaced by compute r methods 10 process voluminous data of this nature. Such programs are developed and available. However, a program called RELCODE is used in this case to correspond to the manual examples and to take into account the suspensions. These analytical procedures form the basis for those studies required for good maintenance management."

Jan 1, 1985

By M. A. Sobhi, L. Li

With the continuous reduction of mineral resources at shallow depth, more and more mines have to go deeper beneath the earth's surface to reach the ore zones. This increase in mine depth leads to a natural stress increase, which also raises the stresses around mine openings. This may result in ground instability, including the risk of rock bursts or exceedingly large opening closure. Stope backfilling is a well known solution to improve the ground stability condition. It also has the advantage of reducing the mining wastes disposed on surface, thus helping to reduce the environment impact from the industry. However, most available solutions for backfill design were developed for an isolated stope without taking into account the influence of mine depth, except for a few numerical analyses performed recently by Falaknaz and coworkers for the case of multiple backfilled stopes laying in the same level. In this paper, a numerical study is carried out to evaluate the stresses in backfilled stopes overlying a sill mat. The mine depth and the excavation of the underlying stope below the sill mat are both taken into consideration. Compared to the case of a single isolated backfilled stope, the obtained numerical results show that the stress magnitudes in the overlying backfill are considerably increased due to the excavation of the underlying stope. In general, the stresses increase with mine depth and backfill stiffness, but decrease with an increase in the surrounding rock mass stiffness. These results indicate that the barricade and sill mat backfill design should take into account the excavation of the underlying stope and the mine depth.

Jan 1, 2015

By M. Dosoudil

"Continuous pressure filtration is a modern process for the mechanical dewatering of flotation concentrates of coal and similar coal slurries. This method will give a lower moisture content than classical vacuum filtration, the improvement lying in the range 5% to 15%. Eighteen coal slurries have been examined in this survey. They are representative of a wide spectrum of filtered slurries. IntroductionDuring the last five years, a number of coal slurries have been tested either in the laboratory or with a pilot plant. The test pressure ranged from one to six bar. The results have been evaluated by mean s of a computer. Determination of the filter capacity and the resulting moisture content and energy consumption has been made with respect to the continuous pressure filter, Amafilter construction-type KDF (Fig. I) . Standard sizes of these filters are 60 m2, 90 m2 and 120 m2.The continuous pressure filter is a horizontal filter with a level tank. Six filter axles are mounted on a rotating main shaft, each with a particular number of elements attached. The elements rotate on their axes and move along a circular trajectory. Periodically the elements submerge into and emerge out of the slurry. A constant air pressure is maintained above the suspension, thus providing the pressure gradient necessary for filtration. The filtrate together with the dewatering air flows through the elements into the hollow axle and out of the filter."

Jan 1, 1987

By D. Mills, W. H. S. Lawson

"The need to make repairs is seldom a major consideration in the design, fabrication and installation of major components of electrical generation plants. Repair welding, however, is a fact of life in the electrical generation industry, for restoration of degradation in service, from cavitation of hydraulic turbine runners, to corrosion and fatigue damage in pressure vessels. In making weld repairs to carbon and low-alloy steels, the largest source of trouble is hydrogen embrittlement and related post-weld cracking. Various strategies have been developed to control problems from this source, including post-weld heat treatment, the use of nickel-base alloy filler metals and the temper bead welding technique. Each of these basic strategies is being applied as circumstances require; each strategy must, however, be implemented in a manner that reconciles weldment structure and hardness, degree of restraint and service environment with the consequences of unsatisfactory performance of the repaired component.IntroductionMajor working components of electric generating plants are specified and installed on the basis that, wherever technically and economically feasible, they will retain functional capacity without major repairs for the twenty-five-plus years of normal plant lifetime. Nevertheless, repairs are often required, and welding is usually an essential feature of the work. Remedial welding may be performed to correct design or fabrication errors which become evident only at the time of component installation. The most common causes of requirements for repair involve corrosion, fatigue or related processes which prove more aggressive than expected during service. Increasingly, our planning for future repair requirements is related to continual improvements which are occurring in nondestructive evaluation technology. As components are periodically reinspected during their service life, fabrication induced defects may be revealed for the first time quite late in the life of the component. When this occurs, repair must be considered wherever inaccessibility of a flaw makes it impossible to prove its inactivity. Finally, there are certain components, for instance in hydraulic turbines, which cannot be economically made or used without the expectation of service induced wear. Here, periodic maintenance welding must be regarded as a normal event."

Jan 1, 1981

By Gordon E. Agar

"The effectiveness of two this compounds for copper sulphide depression in molybdenite flotation has been examined with batch bench scale tests.Both thioglycollate and trithiocarbonate proved to be good depressants producing results similar to those f or cyanide and hydrosulphide. Ferrocyanide was ineffective on the samplematerial tested.The depressing effect of thioglycollate was readily reversed by an addition of xanthate.IntroductionThe separation of molybdenite from copper sulphide minerals has been practised for a long time(1,2). The predominant scheme is to depress the copper sulphides while capitalizing on the ready floatability of molybdenite to effect the separation. There are many recipes for depressing the copper minerals(3), among them the addition of sodium cyanide, particularly if the copper is present primarily as chalcopyrite; some form of sulphide whether as sodium sulphide, sodium hydrosulphide or phosphorous pentasulphide when there is a mixture of copper sulphides such as bornite, chalcocite and chalcopyrite; potassium ferro cyanide may be used when chalcocite is the principal copper sulphide; peroxide or hypochlorite; as well as heating in the presence of lime. There are different mechanisms by which these reagent s depress the copper sulphides. Sodium cyanide and the sulphide-producing compounds apparently reduce the potential of the copper sulphides to the point where they ar e rendered unfloatable by xanthates . Another study(4) showed that after cyanide addition, chalcopyrite was rendered un floatabl e until the REDOX potential (measured with a gold electrode with a saturated calomel reference) had become more positive than -250 mY. If the chalcopyrite pulp was conditioned after the cyanide addition the REDOX potential increased slowly, whereas if air was introduced during the conditioning the potential r ose much more rapidly. The difference in time to reach the desired level of - 250 mV was as much as 20 minutes&apos; 25 minutes being required when air was absent but less than 5 minutes when air was admitted . These observation s demonstrate some of the problems encountered when using cyanide to depress sulphides such as chalcopyrite . The system adjusts to counteract the depressing effect of the additive. To overcome this tendency it is necessary to either add an overdose at the beginning or to more or less continuously add the regulating reagent. In this study cyanide solution was added under automatic control to maintain a specified REDOX potential."

Jan 1, 1984

By Göckmann. Klau

"IntroductionCopper has been recycled ever since its discovery. Even in Graeco-Roman times recycling of this resistant, and thus valuable material was carried out as a matter of course. Just take, as an early example, the Colossus of Rhodes: after the figure collapsed during an earthquake, the bronze parts were melted down into ingots and sold.Copper is a material which can be recycled again and again because copper produced from recycling is not different from copper originating from primary materials. This is mainly due to electrolytical copper refining whereby not only the base metals but also the precious metals can be removed. In contrast, with aluminum and iron only the more electropositive elements can be removed by refining, and the resultant scrap must, therefore, be sorted mechanically into various alloys for subsequent smelting.The recycling rate for different base metals is given in Table 1. Despite this ideal prerequisite, the generally quoted recycling rate of copper of about 40070 appears rather low. However, it must not be forgotten that the recycling rate is defined as the ratio of the annually utilized quantities of copper scrap and the annual production figures (Table 2). Moreover due to the economic growth over the last 30 years the availability of copper from scrap materials is lower than its consumption because copper is principally employed in very long-life consumer durables and only returns to the recycling circuit after many years. The average time for the copper of some goods to be recycled is detailed in Figure 1."

Jan 1, 1992

By V. Itkin

"Three methods were tested for the beneficiation of aluminum scrap, generated by heavy medium separation of non-ferrous automobile scrap residue. These were: crushing in a shredder followed by screening; grinding in a ball miff followed by screening; and eddy current separation. The best results were obtained with the grinding-screening method. IntroductionThe usual method of aluminum alloy reclamation from non-ferrous automobile scrap residue consists of a two-step heavy medium separation to remove materials lighter than and heavier than aluminum. The resulting aluminum scrap still contains over 15% impurities such as stones and glass, heavy rubber, insulated copper wire , plastics and heavy metals entrapped by macerated aluminum piece s, composite fragments, etc.(2). Upon melting, these impurities create difficulties and yield a low ingot recovery-65% to 70%, hence small foundries avoid this material.There are a number of ways to improve the quality of aluminum scrap such as:(1 ) crushing of the scrap, which powders the brittle content , a major impurity component, followed by screening out of the dust(2) eddy current separation , which removes metals from the material flow, and(3) implement better methods for density separation.The eddy current separation and two variants of the comminution-screening technique were studied by Intermetco Ltd., Hamilton , Ontario."

Jan 1, 1986

By J. L. Dion

"A study of the techniques to integrally cast copper tubes in copper tuyeres for use in blast furnaces has been carried out. The work has been performed in support of current efforts to produce two-compartment tuyeres having improved water-cooling capacity. A test pattern corresponding to a vertical section of a two-compartment tuyere, and including a cast-in-place copper tube, was used to investigate such variables as tube preparation, tube coolant, pouring temperature, pouring rate and gating design. Successful castings, either with a good metalfurgical bond or good intimate contact between the tube and the casting, were produced, with all combinations of gating system and position of the tube tried. However, the pouring temperature, the pouring rate and the effectiveness of the coolant are interrelated and must be controlled to produce a good metallurgical bond.IntroductionAs part of its contribution to, and in collaboration with, the Copper Casting for the Steel Industry Committee, CANMET has undertaken research into the methods and techniques needed for the integral casting of copper tubes into high-conductivity copper castings.The objective was to produce two-compartment copper blast furnace tuyeres in which the water-cooled nose compartment consists of a copper tube metallurgically bonded to the wall of the high-conductivity copper casting. This design, developed in the UK, has demonstrated a much extended service life with attendant economies; unscheduled shutdown of blast furnaces due to tuyere failure is a significant problem in the steel industry. The Canadian steel industry believes that this design will replace the currently used single-compartment tuyere in blast furnaces within a few years.The technology to produce these tuyeres does not exist in Canada. One of the main features is the inclusion of a smooth-walled cooling channel in the nose, which permits high velocity cooling water to be employed. A second compartment acts as a reservoir backup, should failure in the nose occur. This would allow continued use of the tuyere for a period of time, permitting a scheduled shutdown for repair s. To assist the Canadian producers of tuyeres to maintain their market, and the Canadian steel industry to have a reliable domestic supply, it is important that the necessary technology for the production of two-compartment tuyeres be developed and transferred to industry."

Jan 1, 1982

By Joseph W. Mills

"The Mic Mac property comprises 994 acres held under mining concession and approximately 2,000 acres held under development licenses in Bousquet township, Abitibi county, western Quebec.Gold was first discovered in this locality by Tom Duval in June, 1936. In February, 1937, Cassels Duval Mines, Limited, was incorporated under Quebec charter to take over the property. In September, 1937, the property was examined by Agaura Explorations, Limited, and an option agreement was signed on October 6th, 1937. In June, 1938, an option for complete ownership was taken on adjoining claims belonging to Norgold Mines, Limited, and in September, 1938, a mining plant was installed and the sinking of a 3-compartment shaft begun. In June, 1939, an option was taken by Mic Mac Explorations, Limited, on seven claims of Mooshla Gold Mines Company, Limited, that adjoined the Norgold block to the east. In December, 1939, a new company, Mic Mac Mines, Limited, was formed, amalgamating the Cassels Duval, Norgold, and Mooshla claims, as well as two claim groups to the west of the mine known as the Vaughan and West Cassels groups."

Jan 1, 1954

By Hans Lundberg

An electric survey from a &apos;plane flown over the ground is much faster and cheaper than an electric survey carried out on the ground. The results are obtained as continuous recordings that are resolvable into both a depth expression and a conductivity effect, so that the indications are easier to evaluate, as well as to correlate from one flown line to the other. The prospecting technique adopted in our electric airborne surveys may be brie fly described as follows: A loop of many turns of insulated copper cable is fastened around the fuselage of the &apos;plane and connected to a generator supplying a few ampere alternating current, usually of a frequency less than 1,000 cycles per second. Just as the current in the primary coil of a common transformer will induce current in the secondary coil when shorted, the alternating magnetic field from this primary current now induces alternating current in electric conductors that happen to be located in the vicinity of the path over which the &apos;plane is flown. This induced secondary current in each conductive section of the ground causes, in turn, an alternating magnetic field, secondary field, which disturbs or dampens the normal alternating magnetic field from the primary loop flown by the &apos;plane. These secondary fields are then picked up and recorded by the help of detecting solenoids, amplifiers, and recorders carried in the &apos;plane. By closer study of such a secondary field it is possible to localize the secondary current causing it and, thereby, the conducting body that contains the secondary current. In the &apos;plane are continuously recorded, besides the amplitude or intensity of the field, also the phase, which is a measure of how much the recorded secondary field is out of step with the primary field.

Jan 1, 1950

By J. S. Fox

It is generally recognized that the interpretation of bedrock geochemical data in volcanic terrains can be improved by adjusting for rock-type. Various chemical attributes of volcanic rocks have been put forward in the literature as rapid indicators of rock-type, but there is some question as to which of these is the most reliable . Only one such attribute, total iron, seems to have seen systematic use in geochemical mapping in the Flin Flon region. Discriminant analysis of 500 basalts, andesites, dacites and rhyolites suggests that SiO2 is the most important rock-discriminating variable and that MgO, CaO, TiD2, AI2O3 and FeOtot, are successively poorer discriminators. Lithological normalization in the subalkaline volcanic environment should therefore be made over ranges of this variable. Trace-metal data from drill core through the sulphide orebody at Hanson Lake, Saskatchewan are used to demonstrate various approaches to lithological correction, including silica normalization, factor analysis and trend analysis. All of these extract economically important information from the core that is not apparent in the raw data logs. However, silica normalization does not seem to be subject to as many serious limitations as factor and trend analysis in this case, and therefore seems to provide the most reliable basis for the interpretation of subsurface exploration geochemical data.

Jan 1, 1978