Search Documents

By E. L. Horner

"Srnoky River Coal is capable ofprocessing 3 million tonnes per year ofrun-of-mine coal at the Smoky River Coal preparation facilities to produce 2.1 million tonnes of high quality, low volatile coking coal for export markets. Multi-seam surface and underground mining operations are scheduled to maintain raw coal feed to the plant. Two beneficiating circuits wash the coal. A heavy medium cyclone circuit cleans the plus 0.5 mm coal and a froth flotation circuit cleans the minus 0.5 mm coal. Clean coal is thermally dried, loaded into unit trains, treated for dust suppression, and transported to west coast port facilitiesf or export. Plant by-products are used as thermal fuel Jn an adjacent power station. Quality control procedures ensure efficient resource recovery for a yield of uniform specification product, at a 7% ash level. Introduction Smoky River Coal operates surface and underground mines in the Smoky River coalfield. Approximately 3 million tonnes per year (mt/ a) of run-of-mine (ROM) coal can be processed at the coal preparation plant to provide 2.1 mt/ a of clean, high quality, low volatile bituminous coking coal. Coal is processed by heavy media and froth flotation cleaning circuits and is thermally dried.Raw Coal Characteristics The characteristics of the ROM coal, both in terms of quality and size consistency, vary with intrinsic seam qualities and mining methods employed. The two seams mined (No. 4 and No. 10) show distinctly different washability characteristics. Seam No. 4 contains relatively few middlings and can be readily cleaned by dense-medium cyclones and froth flotation to give a clean coal at specification ash content. Seam No. JO is more difficult to wash, and the ash content of the clean coal is higher than No. 4 seam at the same operating conditions. However, when the upper I m is excluded from the plant feed, the remaining lower section has washability characteristics similar to No. 4 seam. Coal mined by underground means sometimes contains caprock and consequently tends to be dirtier than similar coal mined by surface means."

Jan 1, 1985

By A. J. Baer

"DEFINITION OF THE REGION AND ITS BOUNDARIESTHE EXPOSED PART OF THE GRENVILLE PROVINCE is the southeastern part of the Canadian Shield, characterized by crystalline rocks with K-Ar ages of about 1,000 million years. Its Canadian portion is bounded on the southwest by Georgian Bay •and by Paleozoic sediments south of a line passing through Orillia and Kingston, on the southeast by the St. Lawrence River valley and the north shore of the Gulf of the St. Lawrence, on the east by the coast of Labrador and on the northwest by the Grenville front, a linear tec-tonic feature that is a metamorphic transition zone and/or a fault. Rocks located to the southeast of the front have younger K-Ar radiom€tric ages than rocks located to the northwest of it.The region is formed of complexly deformed and highly metamorphosed crystalline rocks and in part differs from other areas of the Canadian Shield by the presence of large amounts of crystalline limestone and bodies of anorthosite."

Jan 1, 1970

By N. Staroselsky

"Significant energy savings are often possible for centrifugal compressors operating in parallel by improved control strategy and improved instrumentation. Blow-off can usually be reduced by improved surge control combined with a better control strategy for loading and unloading the group of machines. More precise and stable pressure control then becomes possible. This improved control strategy will also decrease the frequency of operation near the dangerous limits of surge or overload or overspeed. A sample station of mixed centrifugal and reciprocating compressors is examined and a substantial energy saving with the recommended control strategy is projected from operating data. Present Operating Conditions of the Compressed Air StationThe Compressor StationThe compressor station described here has three centrifugal compressors and three reciprocating. It supplies a mine in New Brunswick.Compressed Air and Power ConsumptionFigure I and Figure 2 provide graphs of air consumption and pressure changes based on the owner's data.During the typical two-shift operating day (Fig . I) in the non-productive shift (midnight to 8:00 a.m.), the consumption stays at a level of 9,000 SCFM. This corresponds to a pressure of 110 PSIG. Then, after 8:00 a.m ., the air consumption starts to increase and th e pressure decreases. Around 10:00 a.m., the consumption reaches its maximum level at 97 PSIG. Around II :30 a.m., the air consumption starts to decrease because of the production drop during the lunch break of the first shift. Pressure increases again up to 109 PSIG. After the break, consumption rises to its maximum level over 16,000 SCFM andpressure drops to 97 PSIG.Around 2:30 p.m., the air consumption drops sharply to 9,000 SCFM because of the production decrease to zero level. This drop results from changing of shifts. The pressure at this time increases again up to 110 PSIG. The second shift (2:30 to II :30 p.m.) is an alogous to the first.During the three-shift operating day, the break around 4:00 . a.m . and the shift change around 6:30 a.m. cause sharp drops in air consumption. The pressure for almost the entire night shift stays near 110 PSIG because the station is working with blowing-off even under the maximum consumption. The analysis of Figures I and 2 shows that the pressure varies with the air consumption changes. During non -productive time (non-production shifts , shift changes and breaks) or during the night shift, the total station capacity is proportional to the discharge pressure. By decreasing the level of this pressure up to 97 PSIG, the flow of the station may be decreased during the non-production time as follow s:"

Jan 1, 1980

By C. Harold Riches

This article is directed co a commentary on the patent system in its relation to the public interest. As man gained supremacy over his environment, he could devote progressively increasing portions o his time to improving his standards of living. In the history of the human race, we have advanced from the hollowed floating log to the modern steamship of the present age; from the sickle and flail to the reaper and combine; from the trumpet and drum as a means of communication co the telegraph, telephone, and radio; from the horse and ox cart to the automobile, truck, aeroplane, and train; and so on ad infinitum through the list of inventions on which are based the industrial and political economies and standards of living we enjoy today. It has also been a long road from the day of the alchemist and his closely guarded secrets to the era of the patent system and its storehouses of knowledge open to the world. The alchemist and the craft and merchant guilds closely guarded their secrets. In fact, they largely opposed innovations on the grounds that they might injure profits and restrict employment. In these days of unrest, with great clamour out of doors for radical changes in our political and industrial economies, it may not be untimely to examine one of the keystones which support the economic structure we know as the free enterprise system, the system which is predicated upon the right of the individual to own property. Many, through impractical idealism, ignorance, confused thinking, or blind political prejudice, advocate the substitution of ownership by the State ? for the right of ownership by the individual. As civilization has advanced to the high standards of living we enjoy today through the efforts of a comparatively few inventors, the patent system which has provided the incentive that created the inventions on which our industries and our employment are based is fully understood and appreciated by a comparatively small percentage of our people. As a result, the patent system, as a keystone in our free enterprise economy, is an apt target for destructive criticism, with the thought, possibly, that by eliminating or drastically restricting the several rights to individual ownership one by one, ownership by the State will progressively replace ownership by the individual.

Jan 1, 1949

By E. Czech

Hydrogen generated through aluminum-assisted water split reaction is a novel, efficient and environmentally friendly method. It has been found previously that the passivation of aluminum can be prevented in neutral (pH=7) or near neutral pH conditions in water by grinding aluminum with a catalyst, such as A12O3, SiO2 or SiC. Recently, the best results have been obtained by using water-soluble inorganic salts (WIS), ground with aluminum. The massive, rapid corrosion reaction of the Al-WIS system which takes place in regular tap (or marine, or ground) water can be utilized to produce hydrogen by aluminum-assisted water split reaction, in-situ, on-demand. The reaction offers clean, low-cost, environmentally benign and entirely recyclable technology for on-board on-demand hydrogen generation. Besides pure gaseous hydrogen, only pure solid aluminum hydroxides AlOOH or Al(OH)3 are formed as the reaction products. The hydrogen yield and Al-WIS reaction efficiency are high. From 1 g of mechanically alloyed aluminum powder, up to 1.25 liters of hydrogen were generated, i.e. efficiency up to 92% was achieved. The amount of hydrogen and hydrogen generation rate depend on various reaction parameters. The effect of chemistry and concentration of additives, water temperature, powder particle size and milling conditions on the reaction kinetics will be presented and the possible process mechanism will be discussed.

Jan 1, 2005

By H. Paudyal, K. Ohto, H. Kawakita, S. Alam, B. Pangeni

The orange waste after lime water modification was converted into promising adsorbents for fluoride by metal loading reaction. The effectiveness and mechanism of fluoride adsorption on metal loaded orange waste gel from synthetic and real plating solution were investigated. Amount of zirconium(IV), aluminium(III), cerium(III), lanthanum(III), titanium(IV), vanadium(IV) and tin(IV) loaded on orange waste from aquearegia dissolution were evaluated to be 1.62, 1.16, 0.93, 0.95, 1.20, 1.12, 0.97 mmol/g respectively. The maximum adsorption capacity (qmax) of zirconium(IV), cerium(III), lanthanum(III), iron(III) and aluminium(III) loaded orange waste for fluoride ions were evaluated to be 1.74, 0.91, 1.07, 0.98 and 1.01 mmol/g from aqueous solution. The mechanism of fluoride adsorption by metal loaded orange waste was inferred to be ligand exchange reaction. Application of zirconium(IV) loaded saponified orange juice residue(SOJR) for real plating solution showed effective removal of trace concentration of fluoride down to the accepted standard. The negligible interference of co existing anions like nitrate, carbonate, sulphate and chloride makes zirconium(IV) loaded SOJR a promising sorbent for waste water treatment. The adsorbed fluoride from fluoride loaded zirconium(IV)-SOJR was effectively desorbed by using alkali solution for its regeneration. This work shed light on the potential application of metal loaded SOJR to remediate fluoride contaminated water for environmental relevance.

Jan 1, 2012

By George P. Demopoulos

In a departure from the traditional domain of hydrometallurgical extraction processes we consider new R&D opportunities for innovative application of solution processing into the advanced green energy and clean technology fields. It would not be an exaggeration if we state that protection of the environment via advancement of clean technologies on the one hand, and harvesting and utilizing renewable energy in a sustainable and cost-effective way on the other hand are clearly among the top pressing global priorities. When hydrometallurgy is approached on the basis of its aqueous chemistry and reactive processing fundamentals, it can indeed provide a highly fertile ground for innovation outside the "box". In this context therefore we will present highlights from our recent research that is directed towards the development of new generation HCl recycling, environmental, and solar energy conversion/storage technologies. In all systems the research is approached via the innovative integration of aqueous process engineering and material chemistry principles. The presentation will include discussion of (i) the development of crystallization-based HCl regeneration technologies; (ii) the supersaturation-controlled production and encapsulation of scorodite that was recently commercialized; (iii) the aqueous synthesis of nano-TiO2 and its electrophoretic deposition into solar cell electrodes; and (iv) the hydrothermal synthesis of nanostructured lithium titanate and lithium iron phosphate materials to make lithium-ion batteries destined for electric cars.

Jan 1, 2014

By Philippe Ribagnac, Bruno Courtaud, Jean-Marie Lambert, Valérie Weigel

Mabounié is a polymetallic deposit in Gabon containing niobium (1.2 wt.%), tantalum (0.03 wt.%), rare earth elements (REE) (1.4 wt.%) and uranium (0.03 wt.%) that are mostly carried by pyrochlore minerals. The classical route for niobium recovery is a pyrometallurgical process that consists of pyrochlore flotation, dephosphorization of the niobium concentrate and aluminothermy to obtain ferro-niobium. Pyrochlore concentrates can also be treated by a hydrometallurgical process with a mixture of sulfuric and hydrofluoric acid leaching followed by solvent extraction to separate niobium and tantalum. However, the first process does not allow recovering REE and the second one is not environmentally friendly because of the use of HF. ERAMET is looking for new opportunities on strategic metals market and has recently developed a hydrometallurgical process for the recovery of all these metals based on a sulfuric acid treatment of the ore (Donati, Courtaud, & Weigel, 2014). As for most of the oxidized ore processes, the major impurity is iron (~30 wt.%). Thus, in this hydrometallurgical process, the question arises of the elimination and stabilization of the iron as residue. The iron in solution is ferrous; goethite precipitation seems the most adapted crystalline form. Lab and pilot tests have shown kinetics of precipitation of 6 g.L-1.h-1 at pH 4.5. To reduce the salt discharge, sodium-jarosite form is more adapted, but at pH 2, 95°C only 30% of iron is precipitated in 5 hours, compared to 100% in goethite form at the same time and pH 2, 80°C. Different ways of oxidation were tested, air, pure O2, activated carbon, without drastic effect. The more efficient was ozone use, at room temperature; the kinetics of oxidation is five time faster than the other ways with 30% of sodium removed from the solution.

Jan 1, 2016

By Shek N. Lau, Nicola Samman

"Enclosed gear cases on board heavy mining equipment have traditionally been lubricated with regular heavy duty gear oils. However, equipment manufacturers, have recommended the use of an ISO-1000 gear oil for this application to ensure adequate lubricant film strength, especially at the higher end of the working temperature range. The majority of these ISO-1000 gear oils are based either on residual/asphaltic oil or synthetics, primarily higher viscosity polyalphaolefins. Although the performance of these lubricants has been satisfactory, they suffered other shortcomings that equipment users have lived with over the years.The major requirement at the user’s mine was to provide lubrication for the shovel Hoist gear case. Within such a gear case design, the gears and the roller bearings, that have different lubrication requirements, are lubricated with the same lubricant. Several lubricants were used, light gear oils as well as the recommended ISO-1000 heavy gear oils. On the one hand, the lighter oils performed adequately for the lubrication of the bearings that formed part of the enclosed gear system. These lighter oils did not perform as well for the lubrication of the gears due to their lower viscosities, resulting in shorter gear servicelives.On the other hand, the ISO-1000 gear oils performed well for the lubrication of the gears, but were too viscous to creep into the bearing elements to lubricate them adequately, especially during the cold northern Canadian winters. This resulted in catastrophic bearing failures and secondary damages to the gears.The challenge, then, was to formulate a lubricant which met the 1000 cSt at 40°C viscosity requirement as stipulated by the equipment manufacturer, while satisfactorily lubricating the bearings at the full working temperature range. This was achieved by the development of a semi-fluid grease lubricant, which has proven in field trials to give adequate performance in this application for the lubrication of both the bearings and gears down to -40°C.This product met the equipment manufacturer’s performance criteria and resolved, to a large extent, leakage of the lubricant through seals experienced with the use of conventional and synthetic gear oils.Although the main performance criteria of the fluid was its capability to lubricate the “Hoist” gear case, it was also used during the field trial in other gear cases on board the shovel to test its full capabilities.This unusual alternative lubricant was field tested and evaluated for more than two years. Based on this assessment, the product was reformulated to improve its fluidity, slumpability and the settling of debris/wear metals to the bottom of the gear cases. This reformulated softer grade, a semi-fluid grease, has been performing satisfactorily for more than eight months and is still undergoing longer term assessment."

Jan 1, 1996

By P. C. Patnaik

Performance of industrial gas turbine engines in terms of power output, reduced cooling and efficiency have been continuously increasing in parallel with aero gas turbines due to the advances made in the development of new materials, protective thermal barrier coatings (TBCs) and the advanced diagnostics to monitor service induced problems such as hot corrosion, thermal and thermo-mechanical fatigue and other operational issues, Environmental attack (hot corrosion or high temperature oxidation) is a common degradation mode in the hot section of the gas turbine, Hot corrosion occurs when Na or K bearing compounds in the environment or in the fuel combine with other contaminants such as S and Pb or V to form corrosive sulphates or vanadates thus attacking the protective oxide on the turbine airfoil, These problems pose far more threat to new turbine engine materials such as directional solidified, single crystals and ceramic matrix composites (CMCs). The CMCs due to their increased temperature capability, when used in the combustion chamber, are likely to reduce the peak temperatures attained during combustion and therefore provide the benefits of reduced emissions of oxides of C and N, These issues will be reviewed critically and their impact will be assessed on gas turbine lives. With respect to alternate fuels, past experience has shown that utilization of residual oils and coal derived fuels in gas turbines have resulted in complex deposition and corrosion processes, In recent years biomass derived alternate fuels have been used either through a gasification cycle or through direct firing of the biomass derived liquid fuel with a view to reduce Green House Gases (GHGs) and improve the climatic conditions. In both cases, the resulting high temperature corrosion processes (in the presence of alkaloids in the fuel) are also very complex, leading to premature removal of hot section components, Technology solutions mitigating these fundamental problems will be reviewed and solutions presented.

Jan 1, 2005

By Simon P. Fricker

Gold drugs have been used for the treatment of rheumatoid arthritis since the mid 20th century as disease-modifying antirheumatic drugs (DMARD) class. Methotrexate is often the preferred DMARD, and with the advent of new therapies gold drugs are now used infrequently. Since the introduction of auranofin in 1985 there has been no new clinically approved gold drug. In spite of this apparent lack of progress there has been a great deal of interest in the use of gold compounds for cancer therapy and early promising indications were achieved with a gold phosphine complex [Au(dppe)2]Cl. This compound was not entered for clinical trials, however, due to problems with cardiotoxicity highlighted during pre-clinical toxicology studies. Gold(III) is isoelectronic (d8) with platinum(II) and likewise forms square planar complexes. It is therefore tempting to speculate that such complexes would have similar antitumor activity to cisplatin. In order to stabilise the gold(III) oxidation cycloaurated complexes were synthesised with a single mononegative bidentate ligand, damp, (2-[(dimethylamino)methyl]phenyl), and two monodentate anionic ligands e.g. Cl or acetate. The damp ligand forms part of a five-membered chelate ring. The monodentate ligands are readily hydrolysed and are available for substitution. These compounds had limited anti-tumor activity in in vivo against human tumor xenografts. Mechanistic studies indicated that these compounds had a different mechanism of action to cisplatin. An alternative molecular target for these compounds is biologically important thiol-containing molecules such as the cysteine protease cathepsin B. Modifications were made to the Au(III) damp structure to give compounds with a six-membered chelate ring. These compounds were shown to be inhibitors of cathepsin B. Compounds were also tested for cytotoxicity against a panel of human tumor cell lines. Three compounds were selected for further evaluation against a human colon tumor xenograft. The compounds showed modest anti-tumor activity but with no marked improvement over the parent Au(III)damp complexes. Initial indications are that Au(III) compounds targeted against disease-specific thiol-containing biological molecules have potential as drugs, particularly for cancer. However, further work is required to produce a target-specific drug with a suitable pharmacological activity and toxicity profile.

Oct 1, 2003

By E. L. Bruce

EUROPEAN Russia is mainly a great plain, the average elevation of which is only 600 feet above sea level and the maximum elevation less than 1,200 feet (Figure 1). The main divide between the Arctic ocean and the Black sea and Caspian sea is an indistinguishable topographic feature from which the Dneiper and Don rivers flow southward to the Black sea and the Volga river to the Caspian. The valleys of these rivers are but little below the general level (Figure 2). To the south, this great, rolling plain is broken by a low ridge of Precambrian gneisses and intrusive rocks. The Crimea is an upland from which the descent to the Black Sea coast is precipitous (Figure 3). The Ukrainian Soviet Socialist Republic occupies the southern part of the plain. It is the southwestern unit of the Union, bordered by Rumania and Poland on the west and by the Crimean Soviet Socialist Republic on the south.

Jan 1, 1938

By Guocheng Pan

"Although many factors play roles in the estimation of recoverable reserves, smoothing effect and conditional bias are considered major geostatistical issues in the estimation. This paper introduces measures for smoothing effect and conditional bias, and provides insights into their relation to the estimation of recoverable reserves. Both smoothing effect and conditional bias are intrinsic to the information effect and kriging estimators. For a given level of drilling information, however, it is possible to identify the optimal search radius that minimizes conditional bias. Furthermore, it is also feasible to define variance correction factor for reduction of the smoothing effect from exploration block models. Both of these components are key to the accurate estimation of recoverable reserves. IntroductionThe accurate estimation of recoverable reserves is critical to decision making in different phases of feasibility study and mine planning. Much attention for improving the methodology of estimation has been focussed on the effect of the change-of-support (Parker, 1980; Dagdelen, 1996). For example, it is essential to make a volume- variance correction to the estimate of multiple indicator kriging (Hoerger, 1992). When the size of block, b, in the geostatistical model differs from that of selective mining unit (SMU), v, a volume-variance correction is warranted for the prediction of recoverable reserves.Most mining plans and decisions are made prior to the availability of high density blast-hole samples. In most mining operations, the true SMU grade Zv is unknown at the time of selection. Instead, the selection is based on the estimate Z v**derived from high density blast-hole samples within the deposit G. Nevertheless, the estimate Z v * of recoverable reserves in the stage of mine planning is derived from exploration data. At the end, the production result must be reconciled to the estimate Z v * . In other words, the selection is based on Z v** from blast-hole samples, while the final production figures are reconciled to Z v * from exploration drilling. For a given preselected cutoff grade z0, the actual mining panels will consist of the units having the estimated grade Z v** =z0 rather than the true grade Zv =z0. The difference between Z v** and Zv is usually of less concern."

Jan 1, 1998

"Acid resistant brick lined autoclaves and related vessels are utilized in pressure oxidation for the recovery of gold, copper, and other metals. The combination of the corrosion resistant membrane, acid resistant brick, mortar and steel shell is a composite system that requires a sophisticated stress analysis. In order to obtain meaningful results both the model and physical properties of the materials must be carefully selected. Evaluation of the calculated results requires an understanding of both the failure mechanisms of ceramics and experience with the performance of existing lining systems.INTRODUCTIONAcid brick lining systems are used in pressure oxidation autoclaves and related vessels to provide thermal and mechanical protection for corrosion resistant membranes that are applied directly to the interior of the vessel shell. The acid brick and mortar must be resistant to the process conditions and must provide a mechanically reliable structure.The construction of lined vessels incorporates a wide range of materials that can include the carbon steel vessel, austenitic weld overlay, lead lining, organic membrane, ceramic brick, mortars and other alloy components. The physical properties of the materials can vary by orders of magnitude and when combined in the construction of the lined vessel create a complex composite structure. The materials may be bonded together or act independently of each other. Stresses are induced into the lined vessel include pressure, thermal expansion, chemical expansion and mechanical loads.The complexity of these systems makes it is very difficult to account for all of the variables in the structural analysis of lined vessels. Historically calculations were simplified and designers primarily relied on experience with previous applications.The greatly improved tools for Finite Element Analysis (FEA) available today allow for detailed calculation of the stresses imposed on the vessel shell and lining. Koning & Lauzon (2004) presented a paper on design fundamentals including a discussion on the application of FEA methods at Pressure Hydrometallurgy 2004 in Banff. When a designer carefully constructs a model and selects the correct materials properties for the calculations, meaningful and useful results can be achieved."

Jan 1, 2012

By Charles Graham

It is the general belief that the coal deposits on Vancouver Island are extremely large, and easily available. Indeed, they are frequently described by prominent public men and by writers in the press as "illimitable" and "inexhaustible." It is well that the facts that have been established as a result of seventy years of surface prospecting, underground operations and extensive diamond-drilling in this coalfield should be disclosed. HISTORY The presence of coal on the coast of British Columbia was first made known by Dr. W. F. Tolmie in 183 5. This coal was brought to him by Indians from the north-east coast of Vancouver Island, probably from Suquash. In 1850 the existence of coal at Nanaimo was announced by Mr. ]. W. MacKay. Development was started in 1852, and coal was shipped before the close of 185 3. The first operations were carried on by the Hudson's Bay Company, who operated the mines until 1861, when they sold them to the Vancouver Coal Mining and Land Company. Practically all of the operations in the immediate vicinity of Nanaimo have been carried on by this Company and its successors. In 1869, Mr. Robert Dunsmuir discovered coal about five miles north-west of Nanaimo, at Wellington. The Welling-ton Colliery Company was organized, and began to produce coal from the Wellington mines in 1871, the coal being shipped from Departure bay. This colliery was a large producer for several years, but was finally closed in 1900.

Jan 1, 1924

By J. Bakos

Solar Hydrogen Energy Corporation (SHEC Labs) recently constructed a pilot-plant to demonstrate a Dry Fuel Hydrogen Generation System that is powered primarily by sunlight focusing-mirrors. The pilot-plant consists of: A Solar Mirror Array and Advanced Solar Concentrator and Shutter System; and two thermo-catalytic reactors to convert Methane, Carbon Dioxide, and Water into Hydrogen. Results from the pilot study show that Solar Hydrogen generation is feasible and cost-competitive with traditional Hydrogen production. More than 95% of Hydrogen commercially produced today is by the Steam Methane Reformation (SMR) of natural gas, a process that liberates Carbon Dioxide to the atmosphere. The SMR process provides a net energy loss of 30 to 35% when converting from Methane to Hydrogen. Solar Hydrogen production provides a 14% net energy gain when converting Methane into Hydrogen since the energy used to drive the process is from the sun. The environmental benefits of generating Hydrogen using renewable energy include significant greenhouse gas and criteria air contaminant reductions.

Jan 1, 2005

By Gorrell. H. A.

Subsurface water data can be very valuable in .petroleum exploration and research. For the discussion of problems related to subsurface waters uniform nomenclature and classifications are required. The term 'connate water' has frequently been incorrectly used. It should .only be used in its original sense in which it is analagous to 'fossil water'. Classifications .based on origin and on sodium-chloride content are proposed. Present and possible uses of formation water analyses are briefly discussed. Since the potential uses of formation water data are not fully understood, complete analyses of selected samples should be made to insure against future requirements. The subsurface waters of Alberta show considerable regional variation in amount and proportion of dissolved salts.

Jan 1, 1958

By R. R. Montigny

A brief description is given of the history, location and geology of the Granisle Copper Limited operation on Copper I land in Babine Lake. Detailed information is given with regard to pit design, planning, drilling, blasting, excavation and haulage. Equipment maintenance and mining costs are also presented.

Jan 1, 1971

By M. Ruel

In today's highly competitive worldwide market, it is becoming extremely important for managers to make sure that all resources are used where needed the most. That way, all resources are generating added value, process control equipments are maintained in an optimal state for best performance, and final product is produced at least cost. Performance monitoring is the only way to ensure that everyone is working on top priorities toward the same goal. How can we add value to these warehouses of data? The data is there and the information is hidden; it is just waiting to be extracted. A process performance monitoring system is able to determine if a loop, a system, a unit, or a plant meets the expected performances. The system prioritizes the areas that need attention. It also provides historical reports of the plant status by areas, by loops, and by identified problems. This information is provided to different categories of users in an appropriate format for each one. The system also includes diagnostics and tools to detect and analyze problems.

Jan 1, 2007

By Dougal R. McCreath, Dwayne D. Tannant, Peter K. Kaiser

The Geomechanics Research Centre at Laurentian University in Sudbury, Canada, has undertaken a five-year research program into the design of support appropriate for control-ling damage caused by rockbursts. Rockburst damage mechanisms in Canadian hardrock mines are reviewed and a support design approach is presented. Each element in a sup-port system performs a reinforcing, holding, or retaining function. The desirable load-displacement characteristics for elements in burst-resistant support systems are described, and recommended support systems are presented for a spectrum of rockburst conditions ranging from minor to severe. A support system can be designed to (a) prevent the triggering of aground fall or a rockburst; (b) deform to accommodate the large imposed deformations arising from a rockburst; or (c) absorb the kinetic energy contained in ejected blocks of rock.

Jan 1, 1996