Search Documents

By Tatsuya Oki

Tantalum capacitors can be found mounted on printed circuit boards of domestic appliances such as personal computers. These capacitors contain a considerable quantity of expensive metal tantalum and can be detached and liberated from printed circuit boards by impact breakers. In this study, the size and density distribution of the liberated electronic devices were investigated. Then, tantalum capacitors were recovered from other electronic devices using size separation and pneumatic gravity concentration methods. More than 70% of Newton's separation efficiency was obtained for tantalum capacitors. High Newton's separation efficiency could be also obtained for other types of electronic devices such as chip resistors.

Jan 1, 2011

By N. Tounsi

The use of analytical modeling of continuous chip formation in conjunction with orthogonal cutting experiments was presented in the open literature to identify the coefficients of material constitutive equation within the practical range of stress, strain, strain rate, and temperature encountered in metal cutting. Identification of reliable constitutive data was hampered by a lack of a reliable model for the prediction of the primary shear zone thickness that affects directly the effective strain rate field. An original analytical model to determine the primary shear zone thickness is proposed in this paper. It is based on the mechanics governing the material flow in the primary shear zone. Based on the distribution of the hydrostatic pressure and the forces measured from orthogonal cutting tests, the model that describes the thickness of the primary shear zone is derived. To validate the model, FE simulations of chip formation using DEFORM3D were carried out for different materials and cutting conditions. The results of the analytical model are in reasonable agreement with FEM results.

Jan 1, 2006

By H. C. Rickaby

The Bannockburn gold area covers the four townships of Bannockburn, Argyle, Hincks, and Montrose, lying in the western part of the Matachewan district of Ontario (see Figure 1). The geology of these four town-ships was studied by H. C. Cooke of the Geological Survey, in 1917-18, and is shown in his map of the district. In the fall of 1930, a rich gold-bearing quartz vein was discovered in the northwest part of Bannockburn by B. S. Ashley. A prospecting rush followed the discovery; many claims were staked in the Bannockburn area, and, during the summer of 1931, a considerable amount of prospecting was done.

Jan 1, 1932

By P. Lausch, Z. X. He, J. F. Archibald

"Documented underground fill failures have resulted because of the lack of adequate knowledge concerning fill strength and other physical parameters, as well as to a lack of consistent quality of fill materials being used by operators. On the basis of literature review and correspondence with backfill operators at 18 mines throughout the province of Ontario, non-systematic quality control procedures have been shown to exist, both within different levels of single operations and between separate mining operations, which act to provide inferior engineered fill materials and erratic application response in situ.Assessment of existing procedures set by mine operators for determining backfill physical parameters, and recommendation of optimum fill material testing and manufacturing guidelines are presented in this paper.A series of standard fill characterization test procedures are recommended to provide substantial, though not comprehensive, fill behaviour review. The purpose of these recommendations is to propose industry standards for backfill quality review. Data acquired could be utilized for fill design functions and as a means of comparing fill quality parameters between sites in a regular and more systematic fashion than is presently done."

Jan 1, 1993

By David J. McDougall

"IntroductionThe production of pig iron, wrought iron bars and castings in Quebec during the 18th and 19th centuries has been so closely identified by historians with the Forges du St. Maurice on the St. Maurice River a few miles north of Trois Rivières (Three Rivers), that one is sometimes left with the impression that it was the only iron works that ever operated in the province. There were however, about twelve others, one of which was so completely re-built that it should probably be considered as a separate entity. All but two were constructed after the midpoint of the 1800s, coinciding with the growing Canadian demand for ""charcoal pig"" for railway car wheels and castings for industry, and about half of them were technically, if not economically, successful. The misconception about the Forges du St. Maurice may have come about either because of its long history of somewhat less than continuous production over a century and a half, or a tendency of Quebec historians to concentrate on events in the French-Canadian rather than the English-Canadian milieu, but whatever the reason, the other Quebec iron work s have been generally ignored. All but one of the Quebec blast furnaces could be described as ""preindustrial"" with capacities ranging between three and ten tons per day, the exception being the Radnor furnace built in 1892 with a maximum production of about 35 tons per day and an alleged capacity of 50 tons per day.Until a railway network was completed in the 1880s, the location of all the Quebec iron works except the Grantham Iron works was dictated by close proximity to adequate ore reserves because horse transport was of little use beyond a ten-mile radius. The other essentials of forest resources (mainly soft woods) for charcoal, limestone for flux and water power, were generally available except within a few miles on either side of the St. Lawrence river. Among the dozen iron works established in Quebec between 1732 and 1880, seven used bog iron ore in charcoal-fired furnaces."

Jan 1, 1983

By Richard W. Lawrence, Richard Poulin

"Numerous processes co-exist for metal extraction and for metal removal from effluents of mining operations. Each process enjoys an economic advantage, including environmental cost and benefit, if utilized in a specific situation. This applies equally to biohydrometallurgical processes. This paper will analyze four types of biohydrometallurgical processes for their economic and environmental attributes: biooxidation of refractory gold, extraction of copper from sulfide, metal removal from effluents by active sulfate reduction, and metal removal by the use of wetlands. By examining the economic and environmental advantages of these processes, generalizations can formalized and it becomes possible to define niches of application where biohydrometallurgy can be considered. Our analysis shows that biohydrometallurgy can be efficient at small scale, be more environmentally friendly than conventional technologies and is relatively easier to operate. The higher financial risk associated with unproven technologies at the commercial scale is being eliminated as biotechnology-based plants are put into production.IntroductionBiotechnology can be described as the rational exploitation of the activities of living cells or parts thereof, requiring an integrated multidisciplinary approach between biological and technical disciplines. Microbiology, biochemistry, botany, molecular biology, chemistry and engineering all contribute to practical applications in the extraction, manufacturing and service industries, and in environmental management. Considerable commercial success of biotechnology has been achieved in several sectors, including health care, agriculture, forestry and aquaculture.Over the past 40 years, industry, research organizations, government laboratories, and universities in a large number of countries have participated in investigating the utilization of biotechnology applications in mining. Today, several technologies are used commercially in well understood and engineered systems which can be grouped under the term biohydrometallurgy. Many more technologies have been demonstrated at laboratory or pilot plant scale. Although initial developments and commercial applications were aimed at metal extraction, the dramatic increase in environmental awareness, the practice of sound environmental management demanded by more stringent regulations over the past decade, and the need for low cost treatment in perpetuity, has led to serious investigation of biotechnology for environmental control. In addition, increasing power costs, lowering of ore grades, and decreasing commodity price in real dollar terms require the use of highly efficient and competitive extractive technologies."

Jan 1, 1998

By Y. Feng

Perovskite structured oxide 15% Y-doped BaCeO3 (BCY15) has been evaluated for use as proton conducting electrolyte in SOFC with propane as the fuel and Pt as both electrodes. Under the fuel cell conditions, BCY15 exhibited high proton conductivity and good cell performances. Propylene was detected as product at the anode outlet, and the product distribution suggests that propane dehydrogenation underwent competition with cracking to lighter hydrocarbons. Stability during cell performance tests showed that there was no obvious degradation for BCY15 electrolyte during operation of C3H8-O2 fuel cell.

Jan 1, 2005

By H. A. Kramer

The Flin Flon mine is at present hoisting 5,000 tons of ore daily. In 1943, a peak production of 6,188 tons daily was maintained. Before discussing secondary blasting, it is felt that a short review of stoping procedure will be of value. A list of papers dealing with various phases of the mining operation is appended. Stoping Practice Stopes vary in width from 30 to 150 feet, in length from 200 to 450 feet, and in height from 200 to 500 feet. A typical stope would be 300 feet long, 300 feet high, and 90 feet wide. The dip of the orebodies varies from 60° to vertical, with an average of 82°. The ore is heavy, having a specific gravity of 4. Both sub-level benching and radial drilling are practised. Blast-hole diamond drills are responsible for 85 per cent of the total production. Two sizes of hole are drilled at present, 11 7 6 -inch and 1%-inch. For bench drilling, the burden on the 1 7/16-inch hole is six feet, with holes on 8-foot staggered centres; in radial drilling, the burden is six feet, with nine feet between the toes. The burden on the l 5/8-inch hole is eight feet with holes on 11-foot centres, or 13 feet on the toe of fanned holes. Holes are blasted with two No. 8 instantaneous electric caps per hole, using 403 Polar Forcite. A powder charge of 0.15 pounds per ton is used, with a tonnage factor of 5 and 6.4 per foot drilled for the two sizes. Two rows of holes are blasted together. Fragmentation is satisfactory with the above drilling pattern and powder charge. However, some overbreak and fall-off locally results in oversize material. It is estimated that, after primary breaking, 75 per cent of the ore will pass through the grizzly openings and 15 per cent will pass the draw points, leaving 10 per cent that must be broken further to pass the draw points.

Jan 1, 1946

By Yutaro Fukase

Various types of service robots have recently been developed for guarding facilities, caring for the elderly, carrying objects, and cleaning buildings. As barrier-free facilities improve and their use expands, these robots have more space within which to move inside buildings. Yet robots that move autonomously rely on position-detection systems. Though improving rapidly, these systems are far from perfect in determining positions in certain situations, especially when robots navigate large areas or cross various locations. Our group is working to solve this problem by developing a position-detection system using random-dot patterns on a floor. First, we construct a floor with a random-dot pattern and register the positions of all of the dots into a database. As the robot moves across the floor, a camera on the robot captures an image of the floor beneath it and crops the dot pattern in the image. The cropped dot pattern is matched to the dot patterns in the database to determine the position of the robot and the direction in which the robot is facing or moving. In this paper we propose a self-localization system and matching algorithms derived from a space technology and present the results of several experiments.

Aug 1, 2013

By Karina Forster

Open stope design depends on the ore body geometry, loading conditions and rock mass properties to estimate stope dilution and ground support requirements. Rock mass conditions for design primarily rely upon estimates of well established rock classification systems. Many sources of data exist for obtaining estimates for these rock mass classification values which include core logging, geotechnical mapping, geological mapping as well as linking one classification system to another through the use of empirically derived equations. The extent of mapping coverage can also vary significantly based on the data collection technique. This paper proposes an approach where individual components of rock mass classification systems are collected by the different available data collection techniques. Data from different rock types are also considered separately based on their alteration characteristics and general observation products. Data from the Cameco Corporation Eagle Point Mine is presented and an approach is outlined for obtaining average representative classification values for stope hanging wall characterization. The effectiveness of this approach is demonstrated through the analysis of a data base of hanging wall dilution information.

Jun 1, 2012

By S. Bozorgi, K. Anders

"The automotive applications of heat treatable AlCu cast alloys are designed for performance at high temperature, which can be improved using specially alloying element as well as different heat treatment. In this research work an effect of alloying element such as Cu, Ni and heat treatment on microstructures and mechanical properties of AlCu alloy were investigated using optical microscope (LIMI), scanning electronic microscope (SEM) equipped with energy dispersive X-ray detection (EDS), Differential scanning calorimetry (DSC) and mechanical testing. It was found that during solidification most of the elements Cu, Mg and Ni segregated at the grain boundaries in the form of Al2CuMg or Al7Cu4Ni and a very small part of Cu and Ni element dissolved in the FCC-Al matrix. The latter is not completely reclaimable for strengthening mechanisms in FCC-Al matrix in its as-cast state. The results of mechanical test show that yield strength and ultimate tensile strength increases after heat treatment significantly compared with the as-cast state. Furthermore the mechanical properties at elevates temperature (240°C) is higher with higher Cu+Ni+Si containing alloys compared with the less Cu+Ni+Si containing alloy.INTRODUCTION Due to the high strength-to-weight ratio, high strength and ductility at room- and elevated temperature, AlCuSi cast alloys are widely applied in the automotive industries specially for producing cylinder head and engine block, where modified alloys with enhanced metallurgical properties are always needed to satisfy the ever increasing demands for the applications. The AlCu based cast alloys can be strengthened by age hardening. The precipitation processes from which this hardening is derived can be attributed to the presence of selected trace element additions or micro alloying, which can change the process or kinetics of precipitation in age hardenable AlCu cast alloys (Polmear, 1998; Morris, 1991). Furthermore their strength is mainly controlled by the aging process through the precipitation and growth of very fine precipitates of the ?'-phase (a semi-coherent, metastable form of the equilibrium Al2Cu phase) from the Al and Cu Guinier-Preston (GP) zones. Several studies have shown that solute clustering occurs prior to the precipitation of GP zones, and this modifies both the nature and kinetics of the precipitation process. The typical size of GP zones is in the order of tens of nanometers, and the chemical composition of these precipitates is not easily measured, even with a typically analytical electron microscope (Polmear, 1989)."

Jan 1, 2018

By M. Cossette, V. H. Tran

"How can the durability of asphalt pavement be doubled without increasing highway budgets? Asphalt containing asbestos can provide the desired performance with additional costs being made up by longer life. The addition of a low percentage of asbestos to an asphalt mix permits a higher asphalt content without any consequent loss in stability. It is mainly the higher asphalt content that provides improved performance and durability, although the fibrous reinforcement plays a key role in preventing the propagation of micro-fissures. As well, several international studies show that, thanks to the latest production techniques, no environmental hazards need be incurred.RésuméComment doubler la durée des chaussées d'asphalte sans augmenter les budgets de voirie? L’asphalte contenant de l'amiante peut offrir les performances souhaitées et l'augmentation des couts initiaux peut être rapidement compensée par une durée prolongée. L’addition d'une faible teneur en amiante courte il l'enrobe de bitume permet des teneurs en bitume plus élevées sans subir une perte de stabilité en conséquence. C'est principalement la teneur accrue en bitume qui assure un améliorations propriétés physiques et une augmentation des performances mécaniques, ainsi qu'on prolongement de la durée. Cependant, le renforcement fibreux joue un rôle clef en prévenant la propagation éventuelles micro-fissures. Les nouvelles techniques évitent tous risques environnementaux"

Jan 1, 1991

By S Sokhanvaran

Electrodeposition of silicon from a cryolite based electrolyte at a relatively low temperature (1000°C) is a promising approach to generate high purity silicon. In order to obtain fundamental data pertaining to electrowinning of silicon from Cryolite?SiO2 melts, density and electrical conductivity measurements were made. A range of temperatures and SiO2 contents was studied for each property. It was found that while density has an inverse relationship with temperature, the dependence for electrical conductivity is direct. Increasing silica content up to the saturation limit (~ 5 wt%) increases the density whereas further increase in SiO2, lowers the melt density. On the other hand, the conductivity is lower for the melts with greater SiO2 content, at any temperature.

Jan 1, 2011

By Keith Jones, Largo Albert

"Decelerometer testing of a rigid guide system in a mine shaft pro vides usefuI information to operating and maintenance people. High acceleration/deceleration rates can lead to high maintenance costs to bath conveyances and shaft and can also present an operating risk . Possible disastrous results in the shaft have been avoided by restricting the maximum conveyance speed until the shaft and/ or conveyance problems have been solved.The test instrument is a valuable aid especially during commissioning or updating of a hoisting installation. High acceleration/deceleration rates also lead to reduced hoist rope life. During the past fourteen years, a total of 15,000,000 feet of testing was performed in 74 assorted shaft compartments.Based on this experience, it is possible to establish acceptable conveyance maximum speeds provided that all other conditions in the shaft compartment are normal. The body of the paper will present examples of several tests made under actual operating conditions.IntroductionMore and more mine operators are recognizing the real value in the use of the decelerometer for determining the state of shaft guide alignment in their shaft compartments , not only during the initial mine start-up periods, but also on a regular basis while the mine is in production.Decelerometer testing, is a technique in which an accelerometer , commonly known as a decelerometer, is used for measuring conveyance acceleration/deceleration in a lateral plane. lts purpose is to determine the severity of shock loads produced by misaligned shaft guides. Testing is performed by mounting the instrument on the conveyance and operating the conveyance (empty and loaded) at various speeds up to and including full speed . However, full speed may not be attained due to conditions indicated by the tests. These conditions may present an operating risk to the plant."

Jan 1, 1984

By F. Chiesa

Experimental results on thin and thick castings poured in aluminum A356 and magnesium AZ91E by the low pressure permanent mold process have been compared to the result of filling simulations for thin and thick castings. If the results of modeling is reliable when the liquid remains above the liquidus temperature, this is no longer the case when partial solidification occurs. The visco-elastic behavior of a partially solidified liquid is difficult to put into equation as it depends on the amount of shear it has been been subjected to. Attempts to predict misruns with a commercial software has been proven to be very difficult if not impossible; divergence of the numerical solution has been observed unless prohibitively long computing times are used. In order to overcome these difficulties from a practical standpoint, a simple method is proposed which consists in tracking the temperature of the advancing liquid metal front so as to make sure it will always be above so-called `Misrun Critical Temperature' (MCT) determined experimentally for thin and thick aluminum A356 and magnesium AZ91E castings. If the liquid metal front falls below this temperature, a cold-shut or misrun is likely to happen at this location. The values of MCT for thin and thick in aluminum A356 and magnesium AZ91E were determined experimentally on misrun castings of extreme geometries (a thin 2.5 mm wall cover and a 6mm to 25 mm thick bell housing). MCT was found to be lower for magnesium AZ91E and for the thicker castings.

Jan 1, 2011

By A. A. Rafiei, J. A. Finch

A previous study comparing n-pentanol and the polyglycol Fl50 showed that the two reagents could give the same gas holdup but with different size bubbles. The finding implies that bubble rise velocity depends on the surfactant (frother) type. A study using bubble swarms supported the frother type effect but bubble interactions were a possible confounding factor. This study resolves the question by measuring the rise velocity of single bubbles of 0.8-2.5mm diameter over a distance :::: 300cm in n-pentanol and F 150. It is shown that at typical frother concentrations used in flotation that the rise velocity in n-pentanol remains comparable to that in water alone while in Fl50 the velocity is significantly reduced. The results confirm the suspected impact of frother type. It is illustrated that in n-pentanol the rise velocity does not reached terminal; while in Fl50 it does and this is the source of the velocity difference. Advances

Jan 1, 2009

By H. Craig Boyle, Craig H. B. Leitch

"The Trout Lake stockwork molybdenum deposit is located in the Selkirk Mountains of British Columbia, 50 km southeast of Revelstoke. The property is being explored by a joint venture between Newmont Exploration of Canada and Esso Minerals Canada.The deposit is associated with a small granodiorite stock of Upper Cretaceous age (76 Ma) which has variably altered the surrounding schists, argillites and marbles of the lower Paleozoic Lardeau Group to hornjelsic biotite schists and skarn. The intrusive is composed of a small stock and an intersecting network of northeast- and northwest-trending dykes at surface that coalesce downward into a larger stock. There are two main phases of intrusion, with an earlier quartz porphyritic granodiorite cut by an intra-mineral ""quartz diorite"" porphyry. A strong sub-vertical north-trending fault controls the distribution of the mineralized stock work and displays post-mineral movement.Molybdenite, accompanied by pyrite and pyrrhotite, is mainly present along the margins of veins in a well-developed quartz stock work, but occasionally is strongly disseminated in microfractured intrusives. The stock work is strongest in and around the contacts of the intrusive and its apophyses, and occurs over a vertical range of more than 1,000 m. As defined by the 0.10% MoS] contour, the main mineralized zone is up to 300 m long by 200m wide. Preliminary drill-indicated reserves, currently being revised, are approximately 50 million tonnes of 0.23% MoS2, within which are several zones of higher-grade material. Hydrothermal alteration, as defined by quantitative X-ray diffraction studies on composite core sections, is composed of a central quartz/K-feldspar/albite/minor biotite zone coincident with molybdenum mineralization, which is overlapped by a slightly later, antipathetic quartz/ sericite/pyrite zone. Ankeritic carbonate is also a common alteration mineral, but only traces of fluorite, and no topaz or sulfosalts, have been observed. Analysis for trace elements such as Sn, W, Bi, Sb, As, Hg, U, Ag, Au, Mn, Cu, Pb, Zn and F has been limited except for Sn and W, which appear to be zoned inside and outside the Mo zone respectively; the other elements do not show detectable patterns thus far."

Jan 1, 1983

A semi-automatic device has been constructed that can be used to check the solution strength of cyanide solutions. It consists of a wheel on which a gold-foil-bearing glass slide is mounted. The wheel moves the gold foil through the solution under test and intercepts a light beam. As the gold foil is attacked by the cyanide solution its light absorption diminishes. The successive in-crease in transmitted light intensity is recorded and gives a measure of the gold dissolution rate. Curves have been obtained to show the effect of cyanide concentration and oxygen content on dissolution rates. Details are presented of the construction of the unit, and some practical operating procedures are outlined. 0 NE of the important, although often neglected, factors in the extraction of gold by cyanidation is the actual dissolving strength of the cyanide solution. This depends in a

Jan 1, 1964

By K. Yoshida

Recently, light magnesium alloy with superior heat radiating ability has been attracting attention in various fields. However cold plastic working of the alloy is very difficult and hot working necessary. Furthermore, the magnesium of products with complicated shapes is difficult, the processing cost is high, and the applicability of the alloy is limited. In this study, a technique for obtaining fine wires and tubes by cold drawing is examined to obtain wires and tubes with high strength, quality and surface morphology, while decreasing production cost. In addition, the shearing strain of magnesium alloy wires and tubes drawn under various drawing conditions was calculated by FEM analysis. It was clarified that cold drawing of magnesium alloy is possible. It was also demonstrated that greater reduction of the cross-sectional area could be realized during cold wire and tube drawing by optimizing the drawing conditions.

Jan 1, 2006

By S. V. Ulianov, A. Y. Senchenko, A. A. Shvets, A. V. Aksenov

Development of an efficient technology to process complex ores containing gold and antimony as well as silver is described in the paper. The results from the testwork aimed at the valuables recovery by means of flotation are presented. A process sample of antimonite gold-bearing ore was studied in TOMS institute aiming at development of a technology to process such an ore with generation of antimony concentrate and sulphide gold-containing concentrate. Material composition study indicated that the ore included 5.3% of sulphides: arsenopyrite – 2.4%, pyrite -2.4%, and antimonite – 0.5%. Gold is present as an isomorphic dissemination in arsenopyrite. At sighter testing stage a direct selective flotation flowsheet was chosen to process the ore. Antimonite flotation was activated due to addition of lead nitrate. A single cleaning of a rougher flotation concentrate resulted in antinomy concentrate with 30% Sb content and 71% recovery. Au recovery into antimony concentrate did not exceed 1%. Sb flotation tailings were used to float the remaining sulphides and gold. The resulted sulphide concentrate was characterized by Au content of 20 g/t at about 80% recovery, arsenic content - 10% at ~80% recovery, and sulphur content - 18% at ~81% recovery. The sulphide concentrate can be forwarded to further processing aiming at gold recovery. Given that the concentrate is highly refractory it should be pretreated (bacterial or pressure oxidation, Albion process) prior to cyanidation in order to liberate gold from sulphides. The proposed technology allows one to solve the problem of precious metals recovery from antimonite ores.

Jan 1, 2016