Search Documents

By V. K. Karra

"A simplistic algorithm jar simulating the rod or ball mill Bond grindability test applied to ores and minerals is presented. A performance comparison between the present algorithm and a previously published algorithm by Kapurot, modified in this work jar a fair evaluation, is also given. A worked example is furnished jar leading the reader through the various calculations.IntroductionThe Bond grindability test is widely used for the prediction of the power requirement of an industrial grinding mill. The procedures for conducting this test in either a ball or a rod mill are available(1). In the case of a ball mill, batch grind abilities have been correlated to Bond grindabilities to help monitor day-today variations in ore grindability for the purpose of plant control( 2,3). Of special interest is the algorithm presented by Kapur(3) for the simulation of the Bond test. In practice, the test lasts from 6 to 14 cycles (4 to 10 hours). With this algorithm, one can predict the Bond grind ability using information available from only the first two cycles.Sometimes the prepared feed for the grindability test contains too much fines compared to the total product desired at the mesh of grind under consideration. In such a case, the operator separates the fines from the test feed and adds to the remaining coarse fraction an equal amount of fresh feed. This combined feed then forms the feed to the first cycle of the test. In the present work, Kapur's algorithm is modified to include this special case. A new and relatively simpler algorithm is also presented. Statistical equations relating work index to pertinent variables are also given."

Jan 1, 1981

By E. O. Lilge

THE USE of the Driessen cone as a heavy-media concentrator involves a mineral dressing process in which many variables inherent in the ore and in the process may have an effect on the efficiency of mineral separation and the operation of the cone. The magnitude of these effects and their possible interrelationships must be known before a full-scale plant can be designed and built. It appears that, among the most important variables, are the following: Ore Variables: The particle size of feed The difference in specific gravity between economic and non-economic minerals The intimacy of mineral association Cone Variables: Cone inlet area Ore to media ratio Cone ratio Size distribution in heavy media Specific gravity of media Viscosity of media Type of media

Jan 1, 1956

By S. Kursunoglu

The aim of this study was to investigate the effectiveness of Ascorbic (C6H8O6) Acid (AA), Activated Carbon (AC) and Guar Meal (C6H12O6) (GM) as a reductant for the simultaneous complete dissolution of zinc (Zn) and manganese (Mn) from a spent and mixed Zinc-Carbon (Zn-C) and alkaline battery powders in sulphuric acid (H2SO4) leaching. AA was tested previously as a reductant by other researchers while AC and GM were tested as a reductant for the first time in battery recycling. The effects of H2SO4 concentration, AA/AC/GM dosages, reaction temperature and leaching time on the Zn and Mn dissolutions were investigated according to 2k full factorial experimental design and Central Composite Design (CCD) technique; then, a simple optimization study was carried out for comparing the reductants. The optimum reductive acid leaching conditions for AA were determined at 3 hours leaching time, 70°C leaching temperature, 0.5M H2SO4 concentration, 13 g/L AA dosage, 1/20 g/mL solid/liquid (S/L) ratio and 200 rpm stirring speed. Under these conditions, the dissolution efficiencies were 99.9% for Zn and 99.3% for Mn. The best reductive acid leaching conditions for AC were determined at 3h leaching time, 80oC leaching temperature, 1M H2SO4 concentration, 3 g/L AC dosage and 400 rpm mixing speed. Under above conditions, Zn and Mn dissolutions were not complete. At 2M H2SO4 concentration, 10 g GM dosage, 700C leaching temperature, 200 rpm stirring speed, 1/20 g/mL solid/liquid (S/L) ratio and 3 hours leaching time, full dissolution of both Zn and Mn was achieved. As a result, three different reductants were evaluated in this study for complete simultaneous Zn and Mn dissolutions. This paper also compared present test results with previous spent battery recycling studies for Zn and Mn dissolutions. Full valuable metals dissolutions from spent batteries were achieved at low H2SO4 concentrations with AA and high concentrations with GM. Selective precipitations of Zn and Mn from acid solutions were carried out using NaOH and KOH. Using 3M NaOH as precipitating agent at room temperature and at pH 8; 95.4% of Zn and at pH 10; 93.7% of Mn were precipitated from the leach solution. Under the same conditions, using 3 M KOH at pH 8; 91.6% of Zn and at pH 10, 96.4% of Mn were precipitated. Based on the experimental results obtained, an appropriate flow sheet was proposed to recover both Zn and Mn.

Aug 1, 2013

By F J. Pearce

The Steel Company of Canada, utilizing the S-L process, has produced partially and highly reduced pellets for use in the blast furnace. Experimental blast furnace tests, using reduced pellet burdens, have been carried out. The changes in production rate, fuel rate and general performance of both the S-L and the blast furnace processes are indicated. Introduction T HE ore burdens for a blast furnace may be improved in two ways: chemically, by concentrating the ore to a high degree of purity; and physically, by agglomerating or closely sizing the ore particles. Today, many b1ast furnaces are charged with closely sized agglomerates, some of which contain upwards of 66 per cent iron. The further improvement of these burdens by chemical concentration may, in many instances, be uneconomic due to the large losses of iron that occur during processing. Assuming that it would be possible to reject all of the gangue minerals, the maximum level of concentration of iron in the hematitic ores would be only about 70 per cent.

Jan 1, 1964

By M. E. Holuszko

A research program has been carried out at the Mining Department of the University of British Columbia to study the effect of wettability of coal on its handleability and bulk density. The effect of moisture content on the bulk density of coal was found to be more pronounced for hydrophilic coals than for hydrophopbic ones. Altering wettability of coal surface leads to different effects of moisture on bulk density. The samples were studied at different fine fractions content, and it was shown that there was no effect of increased content of fines on the bulk density for hydrophobic coals, while for hydrophilic coals this effect was very significant. It was shown that the moisture content at which the lowest bulk density was reached coincides with the critical moisture content for studied samples, as determined from handleability tests using Durham Cone method. This critical moisture is the moisture content at which a sudden deterioration of coal handleability occurs. Based on the bulk density and handleability tests, the flow theory of moist coal is proposed.

Jan 1, 2006

"In the first half of 1990, Cambior earned $1104 million, or $0.37 per share, on revenues of$66.4 million. The company's strong cash position, attained late in 1989 and in the beginning of1990 through the exercise of warrants, put working capital at $83.8 million as of June 30, 1990. Long-term debt was reduced by over $10 million during the weak gold market, leaving the company with a debt to equity ratio of only 0.03. Production for the six first months of 1990 was 107 720 oz. Au, an increaseof24% over the corresponding period in 1989.Financial Profile/Results and Corporate Financial StrategiesTotal revenue for the 1989 fiscal year was $116,883,000 compared to $109,848,000 for 1988. The 1989 results achieved despite a lower average gold price, resulted from a higher level of commercial gold production and a 115% increase in investment income over 1988. Investment income rose to $3,568,000 in 1989 due to higher levels of cash assets.Cambior's mine operating costs increased 19% to $68,561,000 in 1989 from $57,472,000 in 1988. This increase resulted from rising operating costs at the Doyon Mine ($250/oz to $274/oz) due to the shift from open pit to underground operations, as well as from the start -up of three new mines with relatively higher costs. These costs have reached a stable level that should be maintained for the next few years.In 1989, net exploration expenses were $6,838,000, down 31070 from 1988, partially due to the Canadian tax reforms introduced since 1987. Depreciation and depletion grew by $1,432,000 in 1989, reflecting a higher volume of commercial production from the Pierre Beauchemin, Lucien C. Beliveau and Chimo mines.Net earnings for 1989 amounted to $17,661,000 or $0.73 per share compared to $17,438,000 or $0.74 per share in 1988.Cambior has an exceptionally liquid and strong balance sheet. As at December 31, 1989, net working capital stood at $85.6 million, with a total assets base of $338.6 million. With a long-term debt (including gold loans) of $21.5 million and shareholders' equity of $277.2 million, Cambior has a debt to equity ratio of 8%. All but about $100,000 of long-term debt is in the form of gold loans.The total market value for Cambior's stock as at September 10, 1990, stands at $420million, based on recent stock market prices. Cambior's stock and warrants are traded on the Montreal and Toronto Stock Exchange."

Jan 1, 1990

By J. O. Yeboah, V. Boakye, P. A. Bepswa, M. Lombard, G. Nutor

The comminution circuit at Tarkwa Gold Mine was commissioned as a Single Stage SAG mill operated in closed circuit with hydrocyclones designed to process 4Mtpa. The circuit was later expanded by adding a secondary ball mill in closed circuit with hydrocyclones with a view to treat 12Mtpa. The change in the circuit configuration and assigning the low aspect ratio SAG mill for primary grinding application makes the Tarkwa experience unique in terms the optimisation strategy and operating philosophy. This paper reports the findings from a series of surveys performed on this plant. The surveys reported include data obtained when the SAG mill was operated as a single stage mill in closed circuit with hydrocyclones and also SABC mode under two different feed conditions. The differences in operating philosophy between the initial single stage SAG circuit and the current SAG/Ball mill circuit are discussed.

Jan 1, 2012

By Catharine E. G. Farrow, David H. Watkinson

The Ni-rich Epidote Zone of the Fraser Mine at Sudbury is characterized by alteration assemblages rich in epidote, actinolite and magnetite which are roughly concentrically zoned and up to hundreds of meters in length. These zones form discrete areas within the igneous Footwall Breccia below the Sudbury Igneous Complex. The assemblages grade from epidotized Footwall Breccia matrix,through actinolite-bearing rocks with few vestiges of original Footwall Breccia textures, into the most intensely altered rock, a magnetite-rich facies. Pentlandite, pyrrhotite and pyrite are the dominant sulfdeminerals; chalcopyrite is minor. The strongest geochemical differences compared to original Footwall Breccia occur where epidote and actinolite dominate the alteration assemblage (EPDZact facies). The most intense alteration facies are typifed by low Cu/(Cu+Ni) values of <0.1. Strong positive correlations exist between Ni and Co, Cu and Au, and among Ir, Os, Ru and Rh. Chondrite-normalized Ni - PGE -Au - Cu plots display an overall increase in all elements from the least to the most intensely altered facies except for Au and Cu. As the proportion of actinolite increases in the EPDZact facies, the chondrite-normalized profles fatten considerably due to low Au and Cu contents. Abundances of Ni, Ir, Ru and Rhalmost ubiquitously increase with degree of alteration. In contrast, Cu, Zn, Ag and Au contents are low in almost all facies. It is suggested that saline hydrothermal fluids moved through the Epidote Zone formation and became more oxidized as they reacted with the Footwall Breccia and with footwall units, including ultramafic rocks. As this trend continued, magnetite-rich zones eventually developed. The occurrence of calcite locally in these magnetite-rich zones suggests that the pH of the fluid increased, causing Cu solubility to drop as activity in the hydrothermal system waned. Sudden changes in fluid composition such as this may have been due to an influx of fluid from bounding ultramafic rocks. Hydrothermal activity was focused along the margins of footwall ultramafic units. Individual hydrother-mal cells may have formed in the Footwall Breccia along pre-existing structures or sulfde concentrations. Metals may have been scavenged from sulfide-bearing Footwall Breccia and possibly Sublayer rocks. Nickel and some PGE were deposited in the Epidote Zone, whereas Cu, Au and Ag continued out-ward into the footwall where they were deposited as Cu-rich footwall veins. Copyright © 1996 Canadian Institute of Mining, Metallurgy and Petroleum.

Jan 1, 1996

By Catharine E. G. Farrow, David H. Watkinson

Abstract-The Ni-rich Epidote Zone of the Fraser Mine at Sudbury is characterized by alteration assemblages rich in epidote, actinolite and magnetite which are roughly concentrically zoned and up to hundreds of meters in length. These zones form discrete areas within the igneous Footwall Breccia below the Sudbury Igneous Complex. The assemblages grade from epidotized Footwall Breccia matrix, through actinolite-bearing rocks with few vestiges of original Footwall Breccia textures, into the most intensely altered rock, a magnetite-rich facies. Pentlandite, pyrrhotite and pyrite are the dominant sulfide minerals; chalcopyrite is minor. The strongest geochemical differences compared to original Footwall Breccia occur where epidote and actinolite dominate the alteration assemblage (EPDZact facies). The most intense alteration facies are typified by low Cu/(Cu+Ni) values of <0.1. Strong positive correlations exist between Ni and Co, Cu and Au, and among Ir, Os, Ru and Rh. Chondrite-normalized Ni - PGE - Au - Cu plots display an overall increase in all elements from the least to the most intensely altered facies except for Au and Cu. As the proportion of actinolite increases in the EPDZact facies, the chondrite-normalized profiles flatten considerably due to low Au and Cu contents. Abundances of Ni, Ir, Ru and Rh almost ubiquitously increase with degree of alteration. In contrast, Cu, Zn, Ag and Au contents are low in almost all facies. It is suggested that saline hydrothermal fluids moved through the Epidote Zone formation and became more oxidized as they reacted with the Footwall Breccia and with footwall units, including ultramafic rocks. As this trend continued, magnetite-rich zones eventually developed. The occurrence of calcite locally in these magnetite-rich zones suggests that the pH of the fluid increased, causing Cu solubility to drop as activity in the hydrothermal system waned. Sudden changes in fluid composition such as this may have been due to an influx of fluid from bounding ultramafic rocks. Hydrothermal activity was focused along the margins of footwall ultramafic units. Individual hydrothermal cells may have formed in the Footwall Breccia along pre-existing structures or sulfide concentrations. Metals may have been scavenged from sulfide-bearing Footwall Breccia and possibly Sublayer rocks. Nickel and some PGE were deposited in the Epidote Zone, whereas Cu, Au and Ag continued outward into the footwall where they were deposited as Cu-rich footwall veins.

Jan 1, 1996

By Kathy S. Kalenchuk

Damages have been observed in shafts, backfill infrastructure and the slick line at the Leeville Mine. Shaft damage (shearing and spalling of the concrete liner) is attributed to mine-induced rock mass deformations concentrated where regional faults intersect the shafts. Aggregate bin, mixer station and conveyor drive damage (shotcrete shearing, heave of concrete floor slabs and bending of a vertical steel beams) is attributed to rock mass squeezing induced by elevated magnitudes of the vertically orientated major principal stresses. Separation of the slick line has occurred do to extension of the stressshadowed rock mass immediately above the mined out areas. Three-dimensional numerical models have been developed and calibrated to simulated rock mass deformations with magnitudes similar to those believed to have produced the observed damages. By stepping through the mine sequence, models reproduce deformations at the same mining stage as when damage has occurred. Calibrated models have been used to forward project further damage over the remaining mine life.

Jun 1, 2012

By Hal. Oliver

MR.]. G. TRAILL: My only excuse for contributing to the discussion on Mr. Hall&apos;s interesting paper is that I had the good fortune to be employed at Noranda during those romantic years, 1927 and 1928, when construction was at its height. The mine was in course of being rapidly prepared and brought into production, and the initial difficulties in crushing-plant and smelter were being met and overcome. They were stirring days, and perhaps those members who were with the second Empire Mining and Metallurgical Congress in 1927 sensed the atmosphere of excitement and activity that prevailed. Early History. Noranda must surely possess some of the most remarkable ore-bodies known to mining men, and the story of their development is pure romance. Ed. Horne&apos;s faith in the property, and the persistence of Thomson and Chadbourne, were richly rewarded in the end, but only after some very thin times had been experienced. In those early days access to the district was by the Kenojevis river and various portages to Osisko lake, on the shores of which the mine and smelter and the town of Noranda now stand. But all the early work was done on the Chadbourne claims, more than a mile to the west; through the b~sh. I have read a log of the events of that period, and through the whole tale of hard work, discouraging developments, occasional shortages of food, and constant danger from forest fires, can be read the faith and persistence of the men in charge. The Chadbourne ore was of that well-known type which, though just too low-grade to pay (with gold at $20 per ounce), is yet sufficiently encouraging to lead one on in the hope of striking something better. It was only as a last resort that work on the Chadbourne claims was suspended and a diamond drill brought to the gossan-covered hill beside the lake. The diamond-driller told me his version (it may be exaggerated) of how the position and direction of the first hole were decided on. He was told, "You might as well set up your drill here, and drill in, say, that direction". I believe that the first hole went through the richest ore ever found at Noranda. After the drill had gone through about 150 feet of solid sulphide ore running 17 per cent copper and 4 dwt. of gold per ton, it passed into barren rock, but the diamond-driller expressed the opinion (I wonder how he knew)) that the hole would come into ore again before long.

Jan 1, 1937

By M. J. Sapko, R. W. Watson, E. S. Weiss

The relative incerdivity of several blasting agents was evaluated in the Bureau's Bruceton Experimental Mine (BEM) . The minimum charge weights resulting in the ignition of predispersed oil shale dust clouds were measured for each of the explosives. A 400 g unstennned charge of ANFO (ammonium nitrate-fuel oil) was sufficient to initiate an oil shale dust explosion, whereas a 1000 g unstenuned charge of an emulsion blend did not ignite the dust even with the addition of 4% methane gas. Several stenuning materials were evaluated in the BEM for their effectiveness in preventing the ignition of near stoichiometric methane-air mixtures. Water stenuning was superior to all other inhibitors tested against methane. Explosibility testing of fine sulfide ore dust in a 20 L chamber and in the BEM show that the dust is capable of propagating an explosion given nominal concentrations of 700 to 800 g/m3. Results are encouraging and irrlicate that there is merit in pursuing explosive composition as a means of reducing ignition probability of oil shale and sulfide dust clouds generated during nonnal blasting operations. The proper selection of explosives and stenuning materials should significantly reduce the probability of secondacy dust explosions in oil shale and sulfide ore mining.

May 11, 1988

By J. G. Whellock, J. W. Matousek

"In spite of their importance to the economics of many metallurgical projects, the values and technical aspects of precious metals losses in smelting operations are relatively undeveloped subjects. This paper attempts to provide a condensed overview of precious metals losses in pyrometallurgy, using some of the limited production and experimental data available. It is intended for three general groups of metallurgists - operators attempting to improve recoveries, cost-accounting engineers making estimates of metal losses in new or modified smelting plants, and research engineers and students.Distribution coefficients of precious metals, the ratios of metal or matte assays to slag assays, are convenient means of comparing smelting processes and the tendencies of the different metals to enter the slag. For silver in lead blast furnaces this ratio is approximately 250;for gold and the platinum group metals in submerged-arc, electric furnaces it is 900. The ratio for gold and PGMs in converters varies with the degree of oxidation of the charge. The over-all cycle-average for industrial installations is tentatively estimated to be 35.IntroductionThe magnitude of precious metal s losses in pyrometallurgical operation s is difficult to assess. The primary producers are generally reluctant to discuss the subject. The by-product producers (the large sulphide smelters o f copper , nickel, and lead) might be more willing to disclose information, but these have precious metals in their feeds in such dilute quantities that accurate accounting is extremely difficult. It is not until numerous processing steps have been taken t hat the precious metals become sufficiently concentrated to permit acceptably accurate sampling and analytical procedures to be followed. Thus, knowledge of the precious metals contents o f the intermediate mattes and slags may simply be unavailable."

Jan 1, 1990

By P. Coursol

The Noranda Reactor Process (NRP) has been in operation now for more than 30 years and this mature process has attained a high level of performance. The NRP at the Home Smelter of Xstrata Copper treats a wide range of feed materials and a thorough knowledge of both process control and smelting physico-chemistry has been beneficial to help meet the required plant flexibility. In this regard, some level of predictive knowledge related to slag chemistry, in particular, the liquid and solid phases such as spinels or olivines, has been found to be beneficial. In the last decade or so, the availability of commercial thermodynamic modeling packages, such as Factsage1m have been utilized with advantage to help the plant optimize slag chemistry and minimize problems from difficult slags, for example, those the could arise from undue feed variability. This paper illustrates the application of this software in examining a range of operating parameters such as: %Fe in product matte, the %Fe/%Si02 ratio in the slag, the levels of minor slag components including CaO, Ah03, ZnO, and MgO, and the level of oxygen enrichment on the operating conditions of the NRP. The slag composition boundaries at the conditions affecting magnetite control and solid magnetite/other precipitated solid phases, as well the conditions influencing the slag liquidus ranges of NRP slags are also discussed with respect to the overall process chemistry.

Jan 1, 2007

By S. M. C. Santos

Preliminary bench-scale studies were carried out on the leaching of a zinc sulphide concentrate from Somincor, Portugal, and the purification of the resulting pregnant solution using solvent extraction techniques. The sulphide concentrate contained 36% Zn, 36% S, 2% Fe and 4% Cu. The leaching was carried out with sulphuric acid in the presence of ferric sulphate as the oxidant. Important leaching parameters, such as the effect of reaction time, the solid-liquid ratio, temperature and concentrations of acid and oxidant, were investigated. After leaching, the recovered solution was contacted with an organic phase containing Acorga 5640 to remove the copper. Subsequently, the removal of iron from the leaching solution was achieved with a mixture of Cyanex 272 and TBP. This solvent mixture was relatively selective for iron over zinc. The stripping of the loaded solvent was performed with 200 g/L H2SO4. Six countercurrent extraction stages achieved a separation of about 99% of the iron from the leaching solution. The iron-free leachate can be further treated to recover minor metals by cementation, and finally, zinc by liquid-liquid extraction. The advantages of the suggested process relative to the traditional jarosite process are discussed.

Jan 1, 2006

By S. Orangi

A representative sample of ramming paste from a peripheral seam in an aluminium electrolysis cell was taken in order to develop a process to fabricate ramming paste samples in the laboratory. To this end, paste material was compacted in multilayers in a mould designed to be representative of peripheral seams in Alcoa&apos;s smelters. The density distribution in the representative sample was measured ranging from 1.51-1.76 g/cm3. The density range obtained by the proposed methodology in laboratory is 1.47-1.77 g/cm3. The results demonstrate that the proposed fabrication method adequately duplicates paste density from the cell for both one and two layer compaction. Finally, preliminary results related to the compressive strength and Young&apos;s modulus of laboratory samples were obtained at various temperatures and are presented in this paper.

Jan 1, 2011

By M. Uszko

The climatic area in which Poland is located requires heating the ventilation air at intake shafts during the winter season. Air heating of the intake shaft should ensure safe operation of hoisting devices; while at the same time it also affects the conditions of the mine environment. The paper presents the issues of shaft heating in coal mines in terms of the mining law, the effect on the conditions of the mine environment and heating technology solutions used in the mines of Kompania Weglowa S.A. (KWSA).

Aug 1, 2013

By J. Q. Chen

The elastic-plastic behavior and the fracture mechanisms of two 2198 Al-Cu-Li thin sheets are investigated. The first material (2 mm thick) is in a recrystallized state after cold rolling. The second material (6 mm thick) is hot rolled and has a fibrous grain structure. The two materials are studied in both T351 and T851 conditions. Tensile tests are carried out along different sheet directions using flat and notched specimens. Fracture resistance was characterized using Kahn tear specimens and M(T) panels. Macroscopic fracture surface of smooth tensile specimens depends not only on testing material but also on the loading direction. For Kahn tear specimens, fracture is initiated in a small flat triangle whereas slant fracture is observed during crack propagation. Fracture mechanisms were investigated using scanning electron microscopy (SEM) and X-ray 3D tomography.

Jan 1, 2011

By M. Kermani

This paper presents and compares the physical properties of Gelfill and cemented hydraulic fill (CHF) obtained by lab experiments. Gelfill has an alkali activator such as sodium silicate in its materials in addition to primary materials of cemented mine backfill which are deslimed tailings, water and binders. The CHF and Gelfill samples with various mixture designs were cast and cured for 28 days. Initially, the influence of sodium silicate concentration on the mechanical properties of samples was evaluated using the unconfined compressive strength (UCS) test. Consequently, the effect of curing temperature on CHF and Gelfill samples cured in various curing temperatures ranging from 5?50 °C was studied using the UCS test. Microstructure of selected samples was studied wirth the mercury intrusion porosimetry (MIP) technique. This study concludes that: (i) The mechanical properties of CHF can be improved by the addition of appropriate amount of sodium silicate. (ii) The rate of strength acquisition in Gelfill samples is faster than CHF samples over 28 days of curing period. (iii) Curing temperature strongly influences the mechanical and microstructural properties of CHF and Gelfill samples. (iv) The microstructure analysis revealed that the addition of sodium silicate can modify the pore size distribution and total porosity of Gelfill which can contribute to the better mechanical properties of Gelfill. (v) The MIP tests suggested the microstructure of specimens were changed by adding sodium silicate in a way that the Gelfill samples had a higher percentage of fine pores than CHF samples.

Aug 1, 2013

By T. A. Chepushtanova, I. U. Motovilov, V. A. Luganov, G. D. Guseynova

"Kazakhstan has significant reserves of oxidized nickel ore with low nickel content. Processing of such ores is effective via pyrometallurgical technologies such as smelting to ferronickel or matte with consecutive extraction of metals from melting products. There are also many options for direct hydrometallurgical processing. However, they do not provide high nickel recovery.We studied extraction of nickel and cobalt by using combined technology of low-grade ore processing from the Shevchenko Kazakhstan deposit, which includes smelting to poor matte followed by hydrometallurgical processing of the matte. The nickel content in the initial ore was 0.75–0.9%. Pyrite concentrate of Sokolov-Sarybai Kazakhstan deposit containing 0.17% cobalt and 0.06% nickel had been used as a sulphidizer at smelting.As a result of the study, we were able to extract up to 98% of the nickel and up to 80% of the available cobalt. Obtained matte contained 3.1% nickel, 0.29% cobalt, 71.6% iron and 24.3% sulfur. Matte leaching was carried out by hydrochloric acid. The iron content in the pregnant solution was 170–185 g/dm3. Nickel and cobalt precipitation from the pregnant solution was carried out by hydrogen sulfide. Initial matte or cast iron was used as neutralizers during the process. Practically complete precipitation of nickel was achieved at 3–5% excess of neutralizer at 333–343°K in 4 hours; up to 95% of cobalt precipitation was achieved in 50% excess of neutralizer at 363°K in 8 hours. The purified solution contained 200–600 mg/dm3 of nickel, 80-100 mg/dm3of cobalt and 175–185 g/dm3 of iron. The purified solution allows to obtain iron oxides by high-temperature hydrolysis, and to regenerate hydrochloric acid.As a result of non-ferrous metals precipitation we obtained sulfide concentrate with concentration of Ni up to 25% and concentration of Co up to 5.5%. The technology is recommended for semi-industrial testing."

Jan 1, 2016