Search Documents

By J. F. Boux

"The study of the total utilization of fly ash has involved all of the known technology in the processing of this waste material into useful products. In addition, a complete knowledge of all the possible uses of fly ash and its products in the market area was probably the most important factor in evaluating the theory and practical feasibility of the total utilization of fly ash from a single large supplyLaboratory tests carried out on the separation of fly ash into different fractions were shown to improve its value and utilization. Four main fractions were studied: a fine pozzolanic low-carbon fraction; a coarse fraction for light-weight aggregate production by pelletizing and sintering; a high-iron fraction; and a carbon-rich fraction. The term ""beneficiation"" here refers to a process of separating fly ash into more useful components.Laboratory and pilot sinter strand tests were employed to optimize the sintering capability and the quality of the heat-hardened pellets through a study of the agglomeration cycle in four principal heat zones, under controlled conditions of air flow, temperature and atmosphere, and including the controlled sizing of pellets.The suitability of the heat-hardened pellets as light-weight aggregate was evaluated in test batches of concrete, which were compared with concrete containing commercial lightweight aggregate of established quality.A study of beneficiated fly ash pozzolan as a partial cementitious binder component in normal and high-temperature cured concrete was reported in a paper at the re-cent Second International Fly Ash Symposium.Samples of raw and beneficiated Lakeview ash were compared with samples of other established high-quality fly ash pozzolans. The evaluation indicated the usefulness of beneficiated Lakeview ash as a pozzolan. Economic studies indicated that to accomplish the primary objective of total utilization of any single source of fly ash (in this case. fly ash from the Lakeview Generating Station, producing approximately 400,000 tons per year), a broad knowledge of the technology of various mineral processes was essential.The design of the fly ash processing plant had to be based on the disposal of all the raw fly ash produced by the generating station. This is contrary to the normal design of a processing plant in which raw materials are supplied and produced according to product demand. The design, therefore, had to be of such flexibility as to pro-duce as wide a variety of products as possible, and the ability to market them had to be well researched and understood."

Jan 1, 1970

By Alvis L. Lisenbee, Colin J. Paterson, Mustafa M. Hariri

"Abstract-The schist-, sediment-, and intrusion-hosted Tertiary Au-Ag hydrothermal deposits of the northern Black Hills, South Dakota are localized and controlled by various types of fractures. This study is an attempt to distinguish between and discuss the possible causes of these fractures in three mines: Richmond Hill, Annie Creek - Foley Ridge (ACFR), and Gilt Edge.Five models based on the structural and tectonic settings of the northern Black Hills are proposed for the fracture origin. In Richmond Hill mine, mineralized fractures within the schist-hosted deposits are in the form of veinlets and stockworks. Larger veins filling open spaces along schistosity planes are also present. Fractures in Richmond Hill mine are related to breccia pipe emplacement and influenced by the Precambrian foliation.Fractures in sediment-hosted (ACFR) and intrusion-hosted (Gilt Edge) deposits are mode I systematic joints. These fractures, and similar ones examined in seven locations outside the mines, are related mostly to the formation of the Lead-Deadwood dome. Fracture trends vary from one area to another depending on their location with respect to the dome. Other factors, such as the Black Hills uplift, pluton emplacement, and Precambrian foliation, may also affect the fracture trends. The proximity of the mines to domes formed by multiple intrusions, the associated fracture patterns and density, and existence of breccias, may be used in exploration for similar deposits in the northern Black Hills or other areas of similar geologic settings."

Jan 1, 1995

By Alvis L. Lisenbee, Colin J. Paterson, Mustafa M. Hariri

"The schist-, sediment-, and intrusion-hosted Tertiary Au-Ag hydrothermal deposits of the northern Black Hills, South Dakota are localized and controlled by various types of fractures. This study is an attempt to distinguish between and discuss the possible causes of these fractures in three mines: Richmond Hill, Annie Creek – Foley Ridge (ACFR), and Gilt Edge.Five models based on the structural and tectonic settings of the northern Black Hills are proposed for the fracture origin. In Richmond Hill mine, mineralized fractures within the schist-hosted deposits are in the form of veinlets and stockworks. Larger veins filling open spaces along schistosity planes are also present. Fractures in Richmond Hill mine are related to breccia pipe emplacement and influenced by the Precambrian foliation.Fractures in sediment-hosted (ACFR) and intrusion-hosted (Gilt Edge) deposits are mode I systematic joints. These fractures, and similar ones examined in seven locations outside the mines, are related mostly to the formation of the Lead-Deadwood dome. Fracture trends vary from one area to another depending on their location with respect to the dome. Other factors, such as the Black Hills uplift, pluton emplacement, and Precambrian foliation, may also affect the fracture trends. The proximity of the mines to domes formed by multiple intrusions, the associated fracture patterns and density, and existence of breccias, may be used in exploration for similar deposits in the northern BlackHills or other areas of similar geologic settings."

Jan 1, 1995

By Edgar A. Manker

"Today's market for columbium has only developed in the last two decades, and in this sense it is ""newer"" than molybdenum, vanadium and most other steel alloying elements. In this short period, it has assumed a very important role in steel alloying and in superalloys. From a few hundred thousand pounds of columbium in 1960, consumption has grown to nearly 30 million pounds per year, with a market value approaching two hundred million dollars.To assess the outlook for columbium, we will first consider the historical development of consumption and supply, particularly noting that all of today's major mines were developed during the last two decades. From current production, we will attempt to reasonably project the future. This future may well include new producers, particularly some producing columbium as a co-product with tantalum.The growth of current applications, and emerging new applications, will be considered with regard to future consumption and in relation to future trends in pricing.IntroductionThe nineteenth century was a busy time for the discovery and naming of new elements. Among those discovered were columbium in 1801 and niobium in 1844. Although it was later shown that columbium and niobium are the same element, the two names are still used today. Niobium has been pronounced the ""official"" name by the International Union of Pure and Applied Chemistry, but columbium is still widely used in commercial practice, and we have chosen to use columbium in this paper."

Jan 1, 1981

The reliability of mining systems is generally low due to their harsh working conditions. Currently, efforts for improving mining system reliability are often made in isolation. This practice could substantially limit the effectiveness of the efforts on overall reliability improvement of the mining system. To enhance the overall reliability of mining systems, an integrated improvement approach is necessary. In this paper, we developed a framework for integrated mining system reliability improvement to address this issue. In this framework, there are five major components including data integration, business process integration, hardware integration, software integration, and analysis/decision integration, but we only focus on the integrated reliability analysis which is important to the analysis/decision integration. The reliability analysis considers the interactions between machines, and the impacts of design, operation, maintenance, automation and working environment on the overall system reliability. These multiple interactions present a big challenge to accurate reliability prediction. In this paper, we for the first time systematically investigated integrated reliability analysis approaches for dealing with this challenge using novel models and methods, including covariate hazard models, intelligent reliability prediction approach, and complex system modeling methods. While these models and methods have found some successful applications in other industries, they in general have not been effectively used for the reliability analysis of mining systems. Our study results show that the system integration approach is applicable to mining systems and can be used for developing a computer aided integration system for the implementation of the integrated reliability improvement approach.

Aug 1, 2013

By John H. Morris, R. Gwilym Roberts

"The Upper Beaver Mine, Kirkland Lake, Ontario, is a copper-gold deposit in mafic flows and sedimentary rocks. The deposit consists of a number of orebodies of two types: copper- and gold-bearing chalcopyrite-pyrite-magnetite ore; and gold-bearing quartz veins. Chalcopyrite-pyrite-magnetite ore occurs in two structural forms: as cherty interflow material in coarse clastic roks underlying flows; and as veins. Both sedimentary and vein ore occur in each orebody. The goldbearing quartz veins occur in interflow sedimentary units and at the contacts of oligoclase porphyry dykes.The deposit is in a localized, volcanic-sedimentary basin which began to develop during the emplacement of the upper units of the pyroclastic and sedimentary Gauthier Group, and continued to the early mafic flow activity of the overlying Kinojevis Group. The formation of the volcanic-sedimentary basin is ascribed to the D0 deformation. The deformation is significant in terms of the structural configuration in the mine area, and may be significant regionally, but this has not been demonstrated. The early deformation was followed by two tectonic deformations. D 1 is associated with a penetrative mineral foliation, axial planar to upright mesoscopic folds and striking parallel to the trend of regional fold structures. Mesoscopic flexural-slip folds, kink folds and fracture-crenulation cleavage are attributed to the D2 deformation. It is probable that no large-scale fold structures are associated with the D2 deformation. The gold-bearing quartz veins were folded during the D1 deformation.The close spatial relationship of copper-gold, chalcopyritepyrite- magnetite veins with chalcopyrite-pyrite-magnetite in cherty inter flow material is strong evidence for the derivation of the veins from the sedimentary ore by hydrothermal, metamorphogenic processes. By analogy, it is suggested that the gold-bearing quartz veins were formed by similar processes."

Jan 1, 1982

By D. J. Wesolowski, D. A. Palmer, P. Bénézeth, S. Hilic

The equilibrium solubilities of gibbsite, Al(OH)3, and boehmite, A1OOH, have been extensively studied in our laboratory from 30 to 90°C, and 100 to 300°C, respectively, to ionic strengths of 5 mol.kg-1 (NaC1) over a wide range of pH. The resulting solubility constants have been treated with consistent empirical models that incorporate appropriate experimental data taken from the literature. These studies were initiated in part to understand and quantify scale formation in geothermal fields as a result of fluid re-injection from electric power generating plants. Most of the experimental results were obtained through application of a unique potentiometric method that allows for rapid, precise measurement of the in situ pH and allows the approach to equilibrium to be monitored from under- and super-saturation. The experimental program was extended to deal with more basic solutions (e.g., five molal NaOH), in which the dissolution of boehmite was measured for application to the refining of bauxite by the Bayer process. More recent results in strong caustic solutions at temperatures below 90°C were obtained to investigate the dissolution of aluminum-containing sludge from holding tanks at the Savannah River waste reprocessing site. In this case the solubility enhancing effects (kinetic and equilibrium) of triethanolamine were also established and quantified. Finally, potentiometric solubility experiments were conducted (50°C in 0.l mol-kg-1, NaCl) on aluminum alloy sheets to identify mainly the nature of the aluminum oxide/hydroxide surface layer formed under these conditions.

Jan 1, 2004

By Y. M. Zhao, C. L. Duan, Z. F. Luo, X. L. Yang

"Fine coal beneficiation in a dry way is considerably imperative for the efficient utilization and conservation of coal resource in drought regions, especially for China. In this study, a continuous vibrated gas-fluidized bed separator was established and developed based on the results of laboratory batch separation results. The fluidization behavior and the effects of several main parameters including superficial air velocity, vibrational parameters, bed height and separating time were systematically investigated. The results showed that the bed expansion increased linearly with the superficial air velocity and theoretically, higher bed expansion benefited the hindered settling process of fine coal particles. However, larger superficial air velocity would induce intense fluctuation in bed surface and a poor performance of density segregation. The conveying velocity of particles was mainly determined by the vibration angle and a predicted model was established by the nonlinear regression analysis. A theoretical model of bed height distribution was established and this model fitted the measured value well. The beneficiation performance of this separator was evaluated by separating -3+1 mm Wuhai fine coal. The results showed that the probable error, E, is 0.225, indicating a continuous vibrated gas-fluidized bed separator could achieve a satisfactory performance.INTRODUCTIONFine coal beneficiation in a dry way is considerably imperative for the efficient utilization and conservation of coal resource in drought regions, especially for China. Meanwhile, it is also conducive to environment protect and low-carbon, green development of coal sector. In recent years, the increasing academic interest in the field of fine coal dry beneficiation has been aroused in most of big coal countries. In summary, recent processes of fine coal dry beneficiation are, according to their processing principles, mainly classified into two categories: dense medium beneficiation (Dong et al., 2015; Fan, Chen, Zhao, & Luo, 2001; Luo et al., 2008; Macpherson, Iveson, & Galvin, 2011) and improved pneumatic beneficiation (Patil & Parekh, 2011; Yang, Zhao, Luo, Song, & Chen, 2013; Yang, Zhao, Luo, Song, Duan, et al., 2013; Zhao, Zhao, Chen, & Luo, 2015). The former deploys artificial dense medium, such as magnetite powder and fine sand, to form a stable gas-solid suspension with certain density under the function of the upward fluidizing air flow and in some case, the external force field like vibration and magnetic field. Generally, it is believed that the process of air dense medium fluidized bed (ADMFB) is suitable for separation of coarse coal (-50+6 mm) and can't obtain a satisfactory result for fine coal separation (Luo, Chen, & Zhao, 2002; Luo et al., 2008). However, some recent laboratory efforts (Patil & Parekh, 2011; Zhang et al., 2014) attempt to find an improved performance for fine coal beneficiation in ADMFB with some modifications. The point of these works is to use a comparatively shallow bed and finer magnetite powder with appropriate size distribution. It is known that fluidization of finer magnetite powder is prone to arouse adverse fluidization properties such as channeling and slugging. Thus, the external force is introduced to an ADMFB in order to improve the fluidization quality of a magnetite powder bed. Some recent literature on air dense medium magnetically stabilized fluidized beds (Fan et al., 2001; Luo, Zhao, Chen, Fan, & Tao, 2002; Song, Zhao, Luo, & Tang, 2012), air dense medium vibrated fluidized beds (Luo et al., 2008) and Reflux Classifier (Macpherson, Iveson, & Galvin, 2010) reports that the separation efficiency, namely the probably error E value, of dense medium separation of fine coal ranges from 0.066 to 0.07, indicating a good separation performance. But, the main unresolved problems of dense medium beneficiation are located in the processes of product purification and medium recovery and are urgent to be solved befor"

Jan 1, 2016

By Jan Butra

In copper ore mines located in the Pre-Sudeten Monocline the deposit mining using room and pillar systems has been carried out for more than forty years. When implementing mining systems in deep copper ore mines it appeared to be necessary to adapt them to variable geological conditions and natural hazards. In the initial period of exploitation there were mainly caving and rockburst hazards. The adaptation of room and pillar system was connected with a state of knowledge in the scope of identifying, forecasting and controlling rock mass hazards. The new solutions allowed the safe and efficient exploitation of a blanket deposit of variable thickness from about 2 to 15m, seated on progressively increasing depth. They included exploitation in constrained conditions, such as in protective pillars. In the exploitation period, technical and organisational activities aimed at rockburst hazard control were introduced including active methods for controlling rockburst hazard and procedures for conducting mining works in the rockburst hazard conditions. When mining at a depth exceeding 1,200 m, the exploitation method and technique are additionally affected by thermal hazard and by gas and rock breakout hazard. New solutions of the room and pillar system and a longwall system with mechanical mining have been developed for exploitation in the associated hazard conditions. The require application of many innovative solutions in the scope of mining process and ore haulage mechanisation, excavation support and forecasting and control of existing hazards. The main purpose of these solutions is to conduct the safe and economically effective exploitation of the deposit.

Aug 1, 2013

By D. J. Reddish

The paper describes a case study where numerical modelling has been applied to predict potential risks associated with inflows of water in active mine workings from an overlying sandstone aquifer. The objective of the modelling was to predict the development of strata fractures and strains as the longwall panels were extracted and investigate their relationship to an sandstone aquifer. The numerical modelling study also included the investigation of the effect of mining on a fault that existed close to the start position of one of the panels. The potential effects of mining on the fault were undertaken by parametric studies adjusting properties for the fault and the relative position of extractions, which allowed the mine planner to position the panel layout accordingly.

May 1, 2003

By Yann Sivry, S. Subramanian, Divyasree C. Prabhakaran, Jean Riotte

The potential of a bacterial strain isolated from water samples collected from a chromite mine in Odisha, India has been assessed for the bioremediation of hexavalent chromium, a toxic environmental pollutant. The isolate was identified as Sphingopyxis sp., a Gram negative bacterium, adopting molecular biological protocols and biochemical characterization techniques. Detailed investigations on the bioremoval of Cr(VI) were carried out using Sphingopyxis sp. cells and the various parameters affecting the biosorption process were evaluated. About 55 % biosorption of Cr(VI) was obtained using Sphingopyxis sp. bacterial cells and the residual chromium in solution was found to be bio-reduced to the trivalent form, namely Cr(III). Thus, complete bioremediation of Cr(VI) could be achieved using the mine isolate, with contributions from both biosorption and bioreduction mechanisms. The Cr(VI) biosorption isotherm obtained for the isolate was found to follow a typical Langmuirian behavior and the free energy value of biosorption was determined to be ~-25 kJ/mol, indicative of involvement of chemical binding forces in the bioremediation process. The chromium biosorption kinetics by the isolate followed a pseudo second order reaction. The FTIR spectral studies revealed that carboxyl, hydroxyl, amino and phosphate groups were involved in the biosorption process. X-ray photoelectron spectroscopic studies on the bacterial cells interacted with Cr(VI) confirmed the presence of both Cr(VI) and Cr(III) on the cell surface. The electrokinetic studies revealed that the surface potential of the bacterial cells were less electronegative subsequent to interaction with Cr(VI), compared to the cells alone, which further testified to the binding of positively charged Cr(III) ions, formed by bioreduction of Cr(VI), to the bacterial cell surface. A marginal shift in the iso-electric point obtained for the bacterial cells interacted with Cr(VI), corroborated the involvement of chemical binding forces in the bioremediation process.

Jan 1, 2016

By J. Bruce See

INTRODUCTION This symposium at Cu 2019 has been organised to honour and celebrate the career and achievements of Dr Phillip John Mackey, an internationally recognised expert in the production of non-ferrous metals, especially copper and nickel smelting and refining. Phillip was born in Epping, a suburb of Sydney, New South Wales, Australia on 19 April 1941 and is one of 4 children of Gilbert and Philomena (nee Bartlett) Mackey. After completing Primary School in Epping, he attended Marist Brothers High School in Eastwood, Sydney and graduated in 1957 as the Dux of the School. Phillip’s father, being on the staff of the Sydney Technical College, in Ultimo, Sydney had the opportunity in the early 1950s to meet the late Professor Sir Rupert Myers, Foundation Professor of the School of Metallurgy at the New South Wales University of Technology (later called the University of New South Wales or UNSW). Gilbert Mackey was impressed by the new young Professor of Metallurgy and encouraged his son to study metallurgy - at the time an expanding industry in post-war Australia. EDUCATION AT THE UNIVERSITY OF NEW SOUTH WALES Phillip commenced at UNSW in 1958, graduating with honours in 1963. His undergraduate education and training included a few years of part-time study while working at British Motor Corporation on sheet metal forming of car bodies. At University Phillip developed his talent for teamwork. He was a contributing writer to the University newspaper, Secretary of the UNSW Students’ Union and was active in the UNSW Metallurgical Society and co-editor in 1963 of “Metallurgical Review,” the annual journal of the UNSW Metallurgical Society. His diverse interests and curiosity about the world around him were likely nourished while at University. Upon completing his Bachelor’s degree, Phillip was awarded a Commonwealth of Australia Postgraduate Research Scholarship. He began his PhD in 1964 on the thesis topic “Studies in Heat Transfer between Dispersed Liquid Metals and Gaseous Atmospheres” working under the supervision of then Associate Professor Noel Warner, an outstanding Professor at the University. Professor Warner is now an Emeritus Professor at the University of Birmingham and is internationally respected for his pioneering theoretical and practical work on established and innovative smelting processes.

Jan 1, 2019

By J. A. Brusset

Introduction I am indebted for most of the information in this paper to Mr. P. S. Lea, Deputy Chief Inspector of Mines of Great Britain, and Mr. A. E. Crook, Engineering Inspector of Mines, Ministry of Fuel and Power. Other coal-mining men in Canada may be as surprised as I was to learn that there are twenty-five Diesel locomotives in service underground in British gassy coal mines. Many more are in use underground in non-gassy coal mines and in metal mines. Approval has been granted for an additional fifty flame-proof locomotives to be used in gassy mines, and these should be in operation by the end of 1946, or as soon as manufacturing facilities permit.

Jan 1, 1946

By Martin P. Raffield

Placer Domes? Campbell Mine, situated in northwestern Ontario, is undergoing an assessment of the efficiency of the operation which is necessitated by the low gold price and a reducing ore reserve grade. A decision has recently been taken to move away from a functional based departmental structure (underground, engineering, geology, etc.) towards a team-based system where crews, engineers, geologists and supervisors are responsible for the planning and operation of a particular area of the mine. The objective is to improve communication and understanding of the goals and achievements and to ensure a forum is available for the generation of ideas. It is intended to increase the accountability and decision-making ability of the teams in an effort to achieve the mines? safety and production targets. This paper presents a critical review of the progress of this organisational change process and its successes and failures at the time of writing.

Oct 1, 2001

By S. S. Teal, W. W. Weber

"AS THE TITLE implies, this paper will deal with the unusual rather than the standard practices as employed . at the property of North Rankin Nickel Mines, Limited. Fortunately •the mining, with the exception of permafrost conditions, and the milling practices, are the normal approaches dictated by the size, type, and character of the orebody. The unusual aspects are linked directly or indirectly to the isolated location and are •principally ancillary requirements or services covering a broad range from climate to supplies and from finance to entertainment. It is our intent to cover the more salient points of interest together with a brief description of the general operation.To understand the primary motivation of the mine, it must be made clear that North Rankin was conceived as a foothold in the Canadian North, that region embracing 40 per cent of the Dominion which ex-tends north of the commercial tree-line and which includes nearly 50 per cent of the Precambrian Shield, our mainstay of Canadian mining. Secondly, this project was born in an atmosphere of premium sales in the nickel markets, assuring a rapid pay-back of the heavy •capital expenditures. And finally, it has •been coddled through the stark reality of a competitive metal market with the hope and trust that the experiences and achievements will lead over the bill to a bigger and better mine in this virgin territory. This is the briefest story of the mine's history, but it pays tribute to the many people who, in thirty years since .discovery, have championed this project."

Jan 1, 1959

By A. J. Goodman

Introduction The position of Turner Valley in the foothills of Alberta, some thirty-five miles southwest of Calgary, is too well known to need further description. This attempt to interpret in detail the nature of the structure, and its relationship to neighbouring structures, together with general observations on the foothills belt, is based on work carried out in the office of the Supervisory Mining Engineer, at Calgary. The object in view was the correlation of the mass of evidence which had accumulated from the detailed examination of drill cuttings, and to discover, if possible, its structural significance. Unfortunately it is not possible to publish most of this detail owing to its confidential nature, and in consequence the reader is asked to accept certain statements, which under other circumstances would not be made without supporting evidence. The main argument for the general structural interpretation rests on evidence which has already been made public, and it is possible to proceed to logical conclusions on the main points. The evolution of ideas concerning the structure of Turner Valley is somewhat difficult to follow, as, compared with all that has been said on the subject, there is not a great deal on record.

Jan 1, 1930

By M. R. Julien, A. Maqsoud, J. Martschuk, B. Bussière

Acid mine drainage (AMD) from mine wastes is one of the most challenging environmental problems currently facing the mining industry. When mining wastes have the potential to produce AMD, the effluents produced have to be managed to meet existing regulations on water quality. The LTA impoundment (property of Barrick Gold Corp.) located near Malartic, Quebec, contains sulphide tailings that have the potential to generate an acidic leachate. The closure option selected by Barrick was to construct a cover with capillary barrier effects (CCBE), in which the moisture- retaining layer is made of non-acid-generating tailings. Since its construction in 1996, the cover has been monitored to evaluate its performance. For that purpose, various parameters have been measured, including the volumetric water content and matric suction in the different layers of the cover. This paper presents some of the main results from the monitoring program that started eight years ago. The results show that the cover is able to maintain a high degree of saturation in its moisture- retaining layer, acting as an oxygen barrier. The actual performance of the CCBE on the flat surface of the 60 ha site is better than expected at the design stage. The only concern with the LTA cover is the effect of slopes that can reduce the performance of the CCBE during dry periods. However, these effects appear only for short periods of time, and are limited to very localized areas, so that they do not significantly affect the overall performance of the CCBE and its ability to limit the production of AMD.

Jan 1, 2006

By Davis. B. R.

There are a number of hydrogen storage systems proposed for automotive applications. However, all of the current suggestions fall short of the DOE targets for storage density and volumetric density. The DOE has suggested that only through radically new ideas will a practical solution to hydrogen storage for automotive applications be realized. This paper provides some background in chemical hydrogen storage and discusses roadblocks to the implementation of some proposed technologies.

Jan 1, 2005

By R. M. Clowes

"As part of LITHOPROBE's multidisciplinary earth science research program to understand the evolution of the North American continent, studies have been undertaken in a number of key areas in Canada. In the Trans-Hudson Orogen of Manitoba and Saskatchewan, LITHOPROBE results require re-evaluation of tectonic models related to its origin. In the Abitibi greenstone belt of Quebec and Ontario, results indicate a more complex evolution for the southern Superior province, one that links with the development of gold and massive sulphide deposits. As part of the program, the seismic reflection profiling method is being adapted for the mining industry. Three examples demonstrate the subsurface information that can be obtained. In Noranda, the base of the volcanic Blake River group is imaged and reflectivity is tied to geology through well logs; in Matagami, the zone of mineralization is shown to be downdropped along a majorfault; in Sudbury, a new structural model is developed, one that shows marked asymmetry at depth and indicates that some ore-bearing units on the margins of the igneous complex may be repeated at depth. IntroductionLITHOPROBE is Canada's national, collaborative earth science research project, established to develop a comprehensive understanding of how the North American continent has evolved. Ten transects, or study areas, were chosen to investigate pivotal geological features to their deep lithospheric roots. They span the country from the Pacific to the Atlantic Oceans and from the U.S. border to the Yukon and Northwest Territories, and geological time from four billion years ago to the present. A multidisciplinary approach, which is spearheaded by seismic reflection techniques, is essential to developing complete interpretations and outstanding scientific results. LITHOPROBE also has pioneered the use and demonstrated the value of using reflection technology to determine subsurface geology in mining camps.This paper provides an overview of the transects and their significance for the tectonic evolution of North America. Two specific examples demonstrate how we detennine present three-dimensional lithospheric structure and past geotectonic processes which formed it. The application of the reflection method to imaging complex structures in ""shallow"" crystalline rocks has been developed with funding and other support from the mining industry and provincial geological surveys. Sustaining funds, however, are derived from the Natural Sciences and Engineering Research Council and Geological Survey of Canada. Emphasis has been placed on developing deeper penetrating tools for exploration of deeply buried, but economically retrievable, mineral resources near existing mines, where an expensive infrastructure already is in place. Three examples, Rouyn-Noranda in western Quebec, Matagami in northwestern Quebec and Sudbury in northeastern Ontario, illustrate these developments."

Jan 1, 1994

By Harry V. Warren

THE Dolly Varden Mine is situated in the Kitsault River valley, eighteen miles from the head of Alice arm, in the Nass River mining division of British Columbia. During the years 1919-21 it was operated by the Taylor Engineering Company, Limited, and produced 1,300,000 oz. silver from about 36,000 tons of ore. The ore was transported by narrow-gauge railway to Alice arm, and shipped to the smelter at Anyox for treatment. During recent years, a small quantity of high-grade ore has been extracted by leasers and shipped to the smelter at Tacoma, Wash. Unfortunately, the bonanza ores which occurred near the surface did nor persist to depth, and two hundred feet below the exposures only rare and unimportant patches of ridi ore have been found. Two opinions exist as to the origin of this rich silver ore. One, advanced by V. Delmage (1, 2), is that the ores are hypogene, and the other, by G. Hanson(3, 4, S), is that the ores are the result of supergene enrichment. It is true that Dolmage first advanced his view that the ores are primary because they appeared to be analagous to Premier ore, which he had studied in detail and which he considered to be primary. The present authors have had access to excellent suites of material from both mines and consider the comparison well taken, the only essential mineralogical difference being the presence at the Premier mine, in addition to the silver minerals, of gold and electrum. Although the arguments put forward by Delmage have, in the opinion of the authors, never been refuted, nevertheless R. P. D. Graham(6), in a reference to the mine published in 1924, describes the ore as of supergene origin, and since then nobody appears to have challenged this statement. Indeed, in 1935, Hanson re-affirmed his earlier conclusion(5).

Jan 1, 1942