Search Documents

By Louis R. Bernier

Since 1978, most systematic studies of AMD passive treatment with limestone drains (LD) have dealt with coal mines in the United States. The authors present in this paper the first results of a triennial study initiated in 1999 on the performance of LD installed at the Ni-Cu Lorraine old mine site in Temiscamingue during a remediation plan that involved the installation of a cover with capillary barrier effects (CCBE) over the reactive pyrrhotite-rich tailings. Typically, a LD is a trench enclosed by impervious materials filled with crushed limestone and may be oxic or anoxic. Four LD (one filled with marble and 3 with dolomite) were installed at the Lorraine site. The LD have been in operation since May 1999 and are performing differently. The most contaminated mine effluent flows south and is directed towards 3 LD filled with crushed dolomite, while a 4th LD was filled with crushed marble and installed west. The LD filled with marble has been generating maximum alkalinity since the beginning of the passive treatment. Two of the dolomite drains have been generating alkalinity since mid-summer 1999, but one is not, even if a substantial pH raise was observed. A pH above 5.5 is required usually for the dolomite drains to start generating alkalinity. The installation of LD at the Lorraine site contributes significantly to the reduction of metals and sulphates loading.

May 1, 2001

By H. O. Lien

Among the known iron deposits in Canada, many are of low grade and require beneficiation to produce an acceptable blast-furnace feed. Some of the deposits have never been considered for commercial exploitation due to the lack of a suitable concentrating process. A number of deposits of this type are located in Northern Ontario. The problem in upgrading these deposits is three fold. Firstly, the iron occurs as a mixture of magnetite and hematite. Secondly, the grain size of the material can be fine to very fine. Thirdly, the complex mixture of gangue minerals, which consists invariably of silica, flaky silicates and carbonates, slimes excessively on fine grinding. Algoma's efforts to concentrate these iron-bearing materials culminated in the development of a "Selective Flocculation and Desliming Process" employing slimes removal as the sole beneficiation technique. The process was applied successfully in the laboratory using two stages of grinding and a total of seven deslimings. Prior to the removal of slimes, the iron-bearing fines were selectively flocculated from a thoroughly dispersed pulp using a modified starch as flocculant, Sodium silicate was employed as dispersant. An attempt was made to optimize some of the process variables using material from one specific iron formation near the town of Geraldton in Northern Ontario. The preparation of the starch proved most critical. This matter, and the method used to evaluate the degree of breakdown of the starch molecule, are therefore discussed in some detail.

Jan 1, 1978

By X. Cao, A. Birur, R. R. Chromik, J. Cuddy, P. Wanjara, J. Gholipour Baradari, T. Shariff

In this study, 3.1 mm thick Ti-5553 (Ti-5Al-5V-5Mo-3Cr) butt joints were autogenously welded using a 4 kW continuous wave Nd:YAG laser. The effect of welding speed and defocusing distance on the weld quality was investigated in terms of the surface morphology, welding defects, microstructure and hardness. Welds with full penetration were achieved at a defocusing distance ranging from -1 mm to 0 mm and welding speeds from 2.25 to 6.0 m/min. Underfill and porosity were the two main defects most frequently observed but within the optimum process window these defects could be maintained to meet aerospace specification tolerances. The fusion zone (FZ) consisted entirely of retained beta with a refined dendritic morphology. Compared to the bimodal alpha (a) + beta (ß) microstructure of the base metal (BM), the dissolution of the a phase was observed in the heat affected zone (HAZ), which led to an 11 % decrease in hardness from the BM to the FZ. To determine the tensile properties of the welded samples, an automated 3D deformation measurement system was used to measure the local strain in the weld region. The yield strength (YS) and ultimate tensile strength (UTS) increased with increasing welding speed with a highest joint efficiency of 75 % being achieved, albeit with a concomitant reduction in the ductility.

Jan 1, 2010

By A. K. Chetin, W. W. Fitkin

"The reservoirs of Mississippian Mi-dale beds and Frobisher beds found in the Weyburn field lie at the north-western termination of a broad productive belt extending 120 miles along the northeastern rim of the Williston basin. These carbonates, and inter-bedded evaporites, originated during cycles of marine transgression and regression, and were deposited as rock types characteristic of shoal, lagoon, and basinward shelf environments. The Frobisher-Alida Beds, which form a secondary reservoir to the main Midale Beds of producing zone are composed of oolit1c, fragmental-bioclastic, vugular limestone capped by an impervious dolomitic mudstone. Production is controlled by localized structural features resulting from de-positional build-up. Excellent reservoir conditions are accompanied by an active water drive. The Frobisher Evaporite, consisting of massive primary anhydrite with dolomitic veinlets, forms the floor seal for the Midale beds oil accumulation. A significant facies transition into an oolitic, bioclastic, vugular limestone characterizes this unit. Beyond the depositional margin of the evaporitic facies, marked increases in porosity and permeability of the en-tire reservoir are noted. Carbonate units overlying the areal extent of the Frobisher Evaporite exhibit a greater degree of metasomatism, dolomitization, and more abundant secondary anhydrite.Porous carbonates comprising the producing zone of the Midale beds are divided into an oolitic, fragmental bioclastic, vugular limestone, and an overlying granular marly lime-stone unit, capped, by the Midale Evaporite. Oil is accumulated in a stratigraphic trap bounded above and be-low by primary anhydrite and truncated by the post-Mississippian erosional surface. Mississippian strata dip basinward from this erosional surface in a broad homocline exhibiting only minor irregularities. Rapid lateral and vertical porosity and permeability variations are common. Localized, separated, porous lenticles contain interstitial water in areas where the Midale beds are underlain by the Frobisher Evaporite. The major portion of the field, however, is capable of water-free production. Bottom and edge waters are found in certain portions of the field. Productive limits are tentatively defined around most of the present field perimeter. A large area along foe southern edge of the field remains open to future development. Probable ultimate remaining recoverable crude oil reserves, as of September 30th, 1958, were estimated by Mc-Daniel Consultants Ltd. to be in excess of 330 million barrels."

Jan 1, 1959

By Marcondes Lima Costa

The Amazon region is characterized by the development of deep chemical weathering represented by widespread lateritic covers and soils. Two distinct periods of laterite formation can be distinguished: mature laterites from the Eocene-Oligocene (and locally from the end of the Cretaceous), and immature laterites from the Pleistocene. The older laterites occur on plateau landscapes,and the younger ones on widespread hilly to ?at lowlands. Both types show complete or truncated pro?les, generally covered by deep yellow to brown topsoils. The mature laterite pro?les contain high concentrations of gibbsite and/or aluminum phosphate, whereas the immature ones are poor in these minerals. The Amazon region is rich in mineral deposits related to lateritic pro?les. Some mineral deposits are of primary origin but were concentrated to economic grades by lateritic processes. The most important ore deposits are of iron, aluminum (bauxite), kaolin, manganese, gold, nickel, copper and phosphate. These are mainly related to mature pro?les. The wide spectrum of ore deposits and mineralogical and geochemical complexity of the Amazon laterites has been promoted by: (1) the prevalence of ideal conditions for laterite formation throughout much of the Tertiary; (2) the presence of varied basement lithologies due to contrasting geological environments; and (3) a variety of epi-genetic alteration types. The lateritic pro?les show a well-developed ore zonation which is related to speci?c lateritic horizons. Iron and gold deposits occur in the ferruginous horizon, which is nearest the surface; the central aluminous horizon hosts bauxites, aluminum phosphate, strontium and gold;and the lower clayey horizon contains deposits of manganese, nickel, copper and kaolin. Resistate phases which residually accumulate throughout entire pro?les include titanium (as ilmenite andanatase), chromium (as chromite), tin (as cassiterite), yttrium (as xenotime), and niobium (mainly asilmenorutile). Epigenetic alteration, caused by swamp environments developed above truncated lateritic pro?les, has led to the formation of high-grade kaolin and refractory bauxites. The laterites inthe Amazon region contain most of all known kinds of ore mineralization related to laterite processes.

Jan 1, 1997

Several inorganic reagents and organic polymers were tested as depressants in the single mineral flotation of ultrafine iron oxide and hydroxylapatite with Dowfroth 250 as a frother. It was observed that the inorganic reagents and the low molecular weight polymers generally caused dispersion of the ultrafine particles, and consequently their recovery into froth products more or less equaled the recovery of water. On the other hand, the high molecular weight polymers caused different degrees of flocculation of the ultrafine particles, and their recoveries were much lower than the recovery of water. These observations pointed to a need to re-define flotation depressants in fine particle flotation. The traditional definition of a flotation depressant, i.e., to make particle surfaces hydrophilic by forming a hydrophilic film and/or by removing collector and activator coatings, is sufficient for relatively coarse particles. However, to prevent fine and ultrafine particles from floating, a successful depressant should not only make the particles hydrophilic, but also enlarge the particle sizes so that they do not enter the froth product by mechanical entrainment. Polymeric depressants are ideal for these purposes. The different schemes to use polymeric depressants in the selective flotation of fine and ultrafine particles were discussed These schemes involve the integration of the polymeric depressants into other size enlargement processes such as shear flocculation, oil agglomeration, etc., for hydrophobic particles.

Jan 1, 2004

By Marcondes Lima Costa

Abstract-The Amazon region is characterized by the development of deep chemical weathering represented by widespread lateritic covers and soils. Two distinct periods of laterite formation can be distinguished: mature laterites from the Eocene-Oligocene (and locally from the end of the Cretaceous), and immature laterites from the Pleistocene. The older laterites occur on plateau landscapes, and the younger ones on widespread hilly to flat lowlands. Both types show complete or truncated profiles, generally covered by deep yellow to brown topsoils. The mature laterite profiles contain high concentrations of gibbsite and/or aluminum phosphate, whereas the immature ones are poor in these minerals. The Amazon region is rich in mineral deposits related to lateritic profiles. Some mineral deposits are of primary origin but were concentrated to economic grades by lateritic processes. The most important ore deposits are of iron, aluminum (bauxite), kaolin, manganese, gold, nickel, copper and phosphate. These are mainly related to mature profiles. The wide spectrum of ore deposits and mineralogical and geochemical complexity of the Amazon laterites has been promoted by: (1) the prevalence of ideal conditions for laterite formation throughout much of the Tertiary; (2) the presence of varied basement lithologies due to contrasting geological environments; and (3) a variety of epigenetic alteration types. The lateritic profiles show a well-developed ore zonation which is related to specific lateritic horizons. Iron and gold deposits occur in the ferruginous horizon, which is nearest the surface; the central aluminous horizon hosts bauxites, aluminum phosphate, strontium and gold; and the lower clayey horizon contains deposits of manganese, nickel, copper and kaolin. Resistate phases which residually accumulate throughout entire profiles include titanium (as ilmenite and anatase), chromium (as chromite), tin (as cassiterite), yttrium (as xenotime), and niobium (mainly as ilmenorutile). Epigenetic alteration, caused by swamp environments developed above truncated lateritic profiles, has led to the formation of high-grade kaolin and refractory bauxites. The laterites in the Amazon region contain most of all known kinds of ore mineralization related to laterite processes.

Jan 1, 1997

By D. H. Rousell

"Rocks of the Whitewater Group (Aphebian age) oc ithin the Sudbury Basin and consist of three formations rre, from oldest to youngest: Onaping, heterolithic breccias lus an igneous-textured component; Onwatin, argillite and siltstone; and Chelmsford, greywacke with minor argillite with siltstone. Mineralization in these rocks is as follows:1) Sulphides are disseminated throughout the Onaping Formation. Pyrrhotite, the major sulphide mineral, occurs mainly as fragments; other sulphides are chalcopyrite, sphalerite, galena, pyrite and marcasite.2) Zn, Pb, Cu, Ag and A u mineralization in the Vermilion member, a carbonate-chert unit near the base of the Onwatin Formation (Vermilion and Errington mines).3) Pyrite and minor base metals in the Onwatin Formation .4) Mineralized quartz veins, located at or near the base of the Onaping Formation, include such deposits as Moore Lake (Pb, Zn and Ag), Foisey (Zn, Pb), Papineau (Cu, Au and Co) and Proulx (Pb, Zn, and Cu). Quartz-carbonate veins in a meta-gabbro sill contain Cu, Zn, As and Au. Material from quartz veins from two former ""gold mines"" (Gordon Lake and Creighton) yielded no Au values.5) Anthraxolite veins in the Onwatin Formation .The mineral occurrences can be explained in term of either the volcanic theory or meteorite-impact theory of basin formation. According to the latter theory, the sulphide fragments in the Onaping Formation may have been formed by the brecciation of sulphide-rich pods located in the upper mantle and at the base of the transient crater; some of the sulphides may have been derived from target rocks of the Huronian Supergroup. The Vermillion-Errington deposits may represent sedimentary exhalative deposits of the Remac type; mineral-rich brines, trapped at the base of the transient crater, rose upward and precipitated the mineralized carbonate-chert under reducing conditions. These conditions continued throughout the deposition of the upper Onwatin Formation but pyrite was the only sulphide that formed.The quartz veins were emplaced during the time of basin deformation. Metamorphism remobilized and concentrated carbonaceous material in the Onwatin Formation 10 form the anthraxolite veins."

Jan 1, 1984

By Bryan Wilson

Background ?Nickel Rim South Mine started production ramp-up in Q2, 2009. ?The main dewatering pumps were put into use in August 2009. ?3 Feluwa?multisafe?positive displacement pumps ?1700m single lift pumping ?Reliability has been an issue due to the amount of slimes and fibers (from shotcrete) at the pumps. ?Critiqued internal dewatering system to solve some issues we were having with our sumps Findings 1.Much of the final dewatering system was not in place. a)Temporary pain. Difficult to say something is not working when the system was not yet in place as per design. b)Not enough capacity to handle slimes within the system. 2.Need to address issues with the final design: a)Ongoing costs: The end design has operating costs of $2.5 million b)Scoops in Sumps: The end design relies on scoops to be used for cleaning the sumps c)Slimes Recovery: The system mixes 3 different products in the sumps along with the fibers d)Pump repair costs: The existing Tsurumi pumps are too light duty for our slimes

Nov 1, 2011

By Jing Li, Weiqiang Lai, Joe Zhou, Jiezhen Ma, Shuibo Chen, Ashele Copper Company, Feng Gao, Guofu Feng

"Copper-zinc ores often contain gold and silver, which can be recovered into copper concentrate by flotation as by-product. The challenges for operations that produce copper, zinc, gold and silver are the separation of copper and zinc and the low grade of precious metals. Ashele copper-zinc ore in north China contains 2.38% Cu, 0.69% Zn, 0.21 g/t Au and 18.10 g/t Ag and the plant produces copper and zinc concentrates, with gold and silver being recovered into copper concentrate. Copper occurs mainly as chalcopyrite and Zn occurs as sphalerite. Copper is well recovered with a recovery of over 94%. However, the recovery of Zn is substantially low (around 50%) due to fine grain size of sphalerite. In addition, gold recovery is much lower than expected and only 33% of gold in the flotation feed was recovered. The grade of gold in copper concentrate is also lower than the required payable grade (1.0 g/t). To determine the cause for lower Zn and Au recoveries, a plant survey program was conducted on the operation. The information acquired shows that the loss of Zn was mainly in the copper concentrates (accounting for approximately 38% of the head assay); of which, 24% was liberated, 8.5% was associated with chalcopyrite and 4.6% was associated with pyrite, indicating that the separation of copper and zinc was the main cause for the Zn loss, with liberation being the second cause for Zn loss. Future effort in improving Zn recovery should be focused on the separation of zinc from copper. Gold in the ore occurs as both microscopic gold and submicroscopic gold, accounting for 36% and 64% of the head assay, respectively. Microscopic gold occurs mainly as native gold and electrum; it is relatively coarse with a grain size of 10 to 240 µm and a large portion can be recovered by gravity. Submicroscopic gold was mainly carried by pyrite (accounting for 38%), and to a less extent, by tennantite (15%) and chalcopyrite (10%). Gold in sphalerite is nominal (1%). It is suggested that more coarse gold and tennantite be recovered and a gold recovery increase can then be achieved to obtain a copper concentrate with over 1.0 g/t Au through flowsheet optimization. Gravity concentration should be investigated and may be worth added into the existing flowsheet to maximum the gold recovery and grade.INTRODUCTIONCopper-zinc ores containing gold and silver is a subtype of polymetallic sulphide ores. Unlike porphyry copper sulphide ores and iron-oxide copper-gold ores, this type of ores often contains substantial amounts of zinc and lead. Polymetallic sulphide ores are mainly distributed in Canada, such as at the LaRonde and Horne deposits. Other examples include Mt. Morgan in Australia and Boliden in Sweden. Globally, production and reserves from gold-rich VMS deposits account for 1370 t gold. This is equivalent to 1% of the world production and reserves, whereas the Canadian total for gold-rich VMS deposits is 870 t, representing close to 10 % of Canadian production and reserves (Gosselin & Dube, 2005a, 2005b). Flotation is the principal process for processing the copper-zinc sulphides ores, for subsequent smelting, roasting, or hydrometallurgical treatment. Oxidized copper-zinc ores can also be processed using leaching technology. For example, at LaRonde operation (a Cu-Zn-Pb ore containing 3-4 g/t Au and 60-100 g/t Ag) the flowsheet consists mainly of a copper flotation circuit and a zinc flotation circuit followed by a cyanidation process of flotation tails. The precious metals are recovered with copper concentrate, zinc concentrate and cyanidation of zinc tails via Merrill Crowe precipitation (Zhou et al., 2005)."

Jan 1, 2016

By R. K. Jonas

"Pressure leaching and pressure oxidation in autoclaves are important alternatives in the extractive processing of gold, copper and nickel ores. The application of advanced control to pressure leach and pressure oxidation autoclaves could achieve significant benefits as has been shown in alumina pressure leaching. This paper compares and contrasts alumina digestion autoclaves to other mining autoclaves with respect to advanced controls. The application of advanced control in alumina with over 30 units controlled worldwide, and its benefits will be reviewed. The design and potential benefits from advanced control for pressure oxidation and leaching will be presented.INTRODUCTIONIt is this author's position and the purpose of this paper to propose that advanced control could be effectively applied to autoclaves in the nickel, gold, and copper mining processes. This is based on the proven effectiveness of advanced control on autoclaves used in the alumina industry for pressure leaching of bauxite ores. Incremental, but significant increases in production could be realized by applying advanced control to autoclaves, as evidenced by the alumina industry, and this not being implemented in other autoclaves in the mining industry.In addition, today the mining industry is being challenged to improve their production methods. In some markets like nickel, there is pressure to improve productivity and reduce the cash cost per ton. While in other markets like copper and gold, demand is vigorous with favourable pricing, and there are advantages to increase production and productivity given limited plant capacity. Advanced control has proven its capability to improve mineral processing operations through increases in throughput, recovery, as well as reducing variability. In today's mines, autoclaves are being used to a much larger scale and with much larger importance, thus it would be beneficial to improve operational performance through the use of advanced control.Accordingly, it is the author supposition that an opportunity exists in the mining industry to use a proven advanced control technology to improve the operations and financial performance of mines using autoclaves."

Jan 1, 2012

By B. Qiu

The large surface ground movements induced by underground mining could threaten the safety of the pipelines laid across the subsidence-prone area. Existing analytical methods for the stress analysis of buried pipeline over mine subsidence area were based on the assumption of ?thin? pipeline, which limited their applicability. This paper presents the improved model with the capability to determine the stress distribution of the ?thick? pipeline. The pipe-soil interaction in this model was also updated to adapt various pipe soil contact conditions. In addition, the time-dependent effects of dynamic subsidence effects were also added to the model. A case of protecting a long section of a buried large-diameter pipeline over two longwall panels in a shallow mine is shown. The stress distribution along the pipeline is determined and the overstressed sections are identified. A partial uncovering plan was developed based on the predicted stress and complicated terrain at the site.

Aug 1, 2013

By Robert B. Parsons

"On August 8, 1989, the Minister of Finance released a technical paper which sets out many of the details of a proposed 9% federal value-added tax to be called the ""Goods and Services Tax"". The GST, which is scheduled to be implemented with effect from January 1, 1991, will affect all Canadians in different ways and to varying degrees. The mining industry itself should, by and large, benefit from the new tax.IntroductionOn January 1, 1991, it is proposed that the existing federal sales tax will be replaced by a new sales tax - the Goods and Services Tax (GST). GST will be leviedat a rate of 9% on most goods and services consumed in Canada.How it will WorkThe GST will be a tax on the final consumption of goods and services. It differs from a retail sales tax in that it will be collected throughout the production and distribution chain. However, the net effect of the tax paid on a particular good or service will be equivalent. The example above (next column) illustrates the application of the GST to the production and sale of a chair.Illustration of GST for a ChairEssentially, the total tax will equal 9% of the sale price to the final consumer. However, GST will be collected on the value added at each stage of the production and distribution chain . What will be TaxedVirtually all goods and services will be taxed. Items on which GST will not be charged fall into two categories: tax free and tax exempt."

Jan 1, 1989

By R. T. Saxon

Prior to November 1975 there were several failures of front -wheel spindles on large haulage truck s in B.C., attributed to fatigue cracks. Since that time, a non-destructive test program has succeeded in detecting the cracks before catastrophic failure, However, the author regards the failures as just one example of a. general unreliability in large high-strength steel castings and urges the industry to look to forgings for sensitive components of heavy equipment.

Jan 1, 1977

By J M. Gibbs

Craigmont Mines Limited mine 50,000 tons of ore and waste per day from the open pit at Merritt, British Columbia. An electric-powered "down-the-hole" drill, a diesel-powered rotary drill and two electric-powered rotary drills have been used. All primary drilling, as a result of cost and operating experience, is now performed with two electric-powered rotary drills. Trials with various loading techniques have increased the amount of AN-FO and decreased the amount of commercially prepared slurries used for primary blasting. Approximately 95 per cent of the primary blasting is accomplished with AN -FO, mixed at the hole. Introduction THE Craigmont mine is located near the village of Merritt, B.C., 240 miles northeast of Vancouver. The concentrator has been in production since September of 1961. Craigmont is a combined open-pit and underground operation. To date, slightly more than 95 per cent of the mill feed has been mined from the open pit. As underground development proceeds, the ore requirements from the open pit will decrease. The average milling rate from September, 1961, to April, 1964, was approximately 4,900 tons per day.

Jan 1, 1965

By M. Dupuis, V. Bojarevics

It is well known that horizontal current density in the metal pad contributes greatly to the generation of MHD driven bath-metal interface wave. It is possible to compute very accurately the metal pad current density using a very detailed finite element model [1], but a MHD model must be compatible to this level of mesh refinement and to recalculate the current distribution at each time step, including the full busbar supply system. The accuracy of the instability prediction of the cell depends on the accuracy of the metal pad current density calculation. This study presents the comparison of the metal pad current density calculation of the detailed finite element model and the MHD-Valdis model for different metal pad heights and ledge thickness. It also presents the corresponding cell MHD stability predictions.

Jan 1, 2006

By M. Abumiya, N. Onodera

Stabilization of arsenic via the precipitation of large-sized scorodite (FeAsO4·2H2O) particles usually involves the use of expensive autoclave systems operated under high temperature and pressure conditions. Alternatively, DOWA developed a novel scorodite synthesis process (DMSP®) wherein the Fe(II) ions in solution containing As(V) ions were oxidized by O2 gas under atmospheric pressure. In this process, crystalline scorodite particles were formed via the formation of a gel-like precursor containing Fe(II). Based on this concept, in this study, we have demonstrated the synthesis of scorodite particles by the addition of Fe(III)-containing solution to the experimental solution containing Fe(II) and As(V) ions, without the O2 gas oxidation process. Ferric sulfate (Fe2(SO4)3) was used as the source of Fe(III) ions. Results indicate the precipitation of scorodite particles, comparable to that of the O2 gas oxidation method.

Jan 1, 2014

By A. A. Brant

BECAUSE of its simplicity, the dip needle is widely used for locating magnetic rock formations in drift-covered areas. Although it responds only to strong magnetic disturbances, it has the advantage that surveys with it can be carried out rapidly, at relatively low cost, by untrained operators. More accurate surveys can be made with a much more sensitive instrument known as the magnetometer, but this must be operated by a specialist and the resulting survey costs are much higher. Mining men use the dip needle for the location of magnetic ores or mineral deposits associated with magnetic rocks. In certain districts, a survey with the dip needle may aid in solving geological structure. In the Little Long Lac and Crow River gold camps of Ontario, it has recently been used for these purposes. In interpreting the results of a dip needle survey, an understanding of the chief magnetic and mechanical factors determining the dip recorded by the needle is definitely necessary. For example, many observers locate a magnetic body by the highest dip values, apparently unaware that these frequently may not lie directly above the body. It should also be realized that a careful dip needle survey may yield information regarding the dip, breadth, and perhaps depth, of the magnetic body. Moreover, the observer should know when numerous closely-spaced dip readings are necessary, and when the dip may be measured at more widely separated intervals. The purpose of the following article is primarily to describe the factors affecting the registration of the dip needle, with a view to aiding investigators in a more accurate and complete interpretation of their results. To explain the cause of magnetic disturbances (anomalies) and the action of the dip needle, a knowledge of certain fundamental magnetic terms is necessary.

Jan 1, 1938

By H. Kudelka

Copper electrowinning at Duisburger Kupferhuette was introduced in March 1975. The electrowinning plant has a capacity of 10,000 mT of copper cathodes a year. The cuprous oxide feed material is an intermediate product of the treatment of the leach solutions, originating from chloridizing roasting of pyrite cinders. This material is characterized not only by a wide spectrum of accompanying impurities, but also by an unusually high level of precious metals. As the priority set was the production of high-purity cathodes. there was a need for developing a process which would be suited to treat complex leach liquors . The process adopted consist s of an oxidizing leach in spent electrolyte, followed by two- stage purification, By this means. a low- acid pregnant copper electrolyte is obtained free of elements detrimental to copper quality. Electrowinning is carried out at a current density of 200 A / m2 in the presence of 10 g/l zinc. The electrowon copper has a conductivity of at least 101.4% lACS and a softening temperature not exceeding 200°C, which makes it a suitable product for continuous casting and dip ?forming.

Jan 1, 1977

By J. M. Cooper

The HBMS reverb furnace in Flin Flon was originally designed in the late 1920s. Throughout the decades campaign life has been increased due to operational practices, technological changes and brick quality improvements. In recent decades the campaign life had been extended such that a complete rebuild was scheduled every 3 years. The latest furnace rebuild and start up has been after a campaign life of nearly 6 years. Brick construction methods and techniques along with furnace operational practices allow the present campaign to be double that of the historical campaign length.

Jan 1, 2007