Search Documents

By J. Oré

An alternative method for dewatering slurry (tailings) is the use of geocontainers (MacTubes). The practical application of this work was carried out in the concentrator plant of the Raura Mining Company, located in the occidental mountain between Huánuco and Lima in Peru?s central highland. For the development of the research, the MATLAB R2012a software MGeST (v. 1.0) was used (Slurry Geocontainer Maccaferri Treatment). MGeST is used for sizing MacTubes, which allows determination of the most important design parameters, such as height (H), filling residual pressure (P1O ), strength of geosynthetic (T), and dehydration height. Compared with GeoCoPS v. 3.0, there is a maximum difference of 3% between the results obtained. The tailing to be treated in the MacTube have a specific weight of 11.62 kN/m3. After several tests it was determined that a MacTube of an apparent opening size of 0.22 mm was required for this specific weight.

Aug 1, 2013

By M. W. Gilmore, J. Ndlovu, T. Sepoloane, Anglo American Platinum, L. R. Nelson, R. N. Varty, L. J. Bryson, B. Peyper, J. P. Hagemann

"As part of Anglo American Platinum’s Rustenburg Base Metals Refinery (RBMR) expansion, a new Nickel Electrowinning Tank House, with a nameplate capacity of 32 400 tons per annum, was constructed. Commissioning of the new electrowinning technology, which involved world first full deposit plating, commenced in 2011.The old nickel electrowinning process at the RBMR used starter sheets which, along with a divided cell configuration, was very labour intensive and exposed operators to high levels of aerosols that contained both nickel and acid. To overcome this problem two key design intents of the new technology are aerosol abatement and minimising labour in the electrowinning cell environment, with a design target to reduce the nickel occupational exposure limit (OEL) to half the legislated limit of 0.1 mg.m-3.Commissioning of the new technologies adopted to achieve mist abatement is described, together with a review of technical and operational challenges relating to the titanium blank edge strips, blank roughness and sandblasting optimisation, blank quality control, electrode spacing, polyconcrete cell dimensional stability and cell top furniture. The impact of these on process performance is presented and the development of fault checking and rectification methods, to maintain high process performance, is explained.INTRODUCTIONThe expansion of Anglo American Platinum’s Rustenburg Base Metals Refinery necessitated the construction of a new Nickel Tank House to achieve two primary objectives, namely increasing the nickel electrowinning capacity from 22 500 tons per annum (tpa) to 32 400 tpa nickel, and a design to reduce the nickel aerosols to 0.05 mg.m-3 as a time weighted average over 8 hours, which is half of the legislated occupational exposure limit (OEL) of 0.1 mg.m-3."

Jan 1, 2016

By Mafalda Arias

Most mining and mineral exploration companies? operate in remote locations, in Canada or internationally. Not knowing the cultural imprint of your team and the places where your company is active, may lead to problems. To set the foundation for a better world, it?s important to built trust and relationships inside your global team, within communities and together with stakeholders. Building the ?invisible asset? and developing intercultural awareness is an important part of leadership programs for geologists and engineers on your team, and should be a key component of your Corporate Social Responsibility initiatives. Why is culture important for mining and mineral corporations in their CSR initiatives? Because culture is the foundation of your organizational identity. Understanding the impact of identity, for an organization and for each individual, will provide a description of the experiences and values that affect every work placed interaction, with your clients, with colleagues, with suppliers, with the community of the host country. Each one of us sees and evaluates the world through our perceptions. Through these perceptions we give meaning; how we view and understand our reality which sets the tone for how relationships are built. This is what I call building the ?invisible asset?. Identity, experiences, values and beliefs are invisible commodities, locating them can be as difficult as finding a mine. But if they are not located, the commodity does not have value. Just like in the work we do in our industry. For example when you are working in an underground gold mine and the vein is lost, you keep on working and trying to find the vein; time passes, money is being used and no results. You decide to bring an expert on this type of deposits who gave you directions that allowed you to find the vein. To be a responsible citizen of the world and to set the foundation for a better world, it is imperative to go deep, as deep as your next drilling program, because only there and then, can you develop the cultural sensitivity and the ability to become an agent of change for responsible, sustainable and profitable businesses.

Oct 1, 2010

By Paul M. Clifford, David M. Baird

The Great Northern Peninsula of Newfoundland consists of a Precambrian core of gneisses and granitic rocks, cut by numerous diabase dykes. This complex is surrounded by an envelope of sedimentary rocks of Cambrian to Carboniferous age. Radiometric dates from two granite masses in the core give a mini-mum age of -945 m.y. (Grenville) for the last major tectonic activity. This Grenville deformation conferred upon the core substantially its present structure which has controlled later events to a marked degree. Block movements of the core, dominantly in a vertical sense, have ex-posed it to erosion at intervals. The nature and distribution of the flanking sedimentary rocks and the present relief of the peninsula suggest four such movements. THE Great Northern Peninsula extends some 150 miles north-northeast from the northwest corner of the main body of the island of Newfoundland. It separates the Gulf of St. Lawrence from the Atlantic Ocean, except for the 12 mile wide

Jan 1, 1962

By Carl O. Nickle

"IntroductionIF I WERE ASKED what are the two most important single factors in shaping the growth of Canada to date, and in building its future, the answer would be: first, the treasure house of natural resources on and below the surface over the length and breadth of our country; and two, the pioneering spirit and 'get up and go' of many of our people. The two factors are inseparable. Without the pioneering spirit, the natural resources of land, forest, stream, and the subsurface would have continued •to be useless,. Idle assets. With the pioneering spirit, Canada's natural resources have been and are creating economic revolutions.Western Canada oil and natural gas rank high on the list of such revolutions. Calgary, your meeting place today, is the birthplace of this economic revolution, one that has already sharply altered the economy .of the middle half of Canada, particularly that of Alberta; is increasingly making its weight felt on the economy of all Canada; and is helping re-shape world thinking on sources of vital petroleum supply for both peace and war. Calgary is today the 'operation headquarters' for the great bulk of a huge exploration and development programme that now extends over a quarter of a million square miles of Canada's West. As a Calgarian, •therefore, I am particularly happy to have this privilege of talking about oil and natural gas to members of the C.I.M.M., who play a key role in the development of all Canada's varied natural resources."

Jan 1, 1952

By W. B. Timm

Introduction In preparing this paper on Recent Developments in Gold Milling Practice, the idea occurred to me that possibly the best way to deal with the subject would be to take you in thought on a visit to the principal gold mining camps of the Dominion, starting at the east and finishing up in the west, and noting, as we go, the outstanding improvements that have been made in the last few years in the practice of gold milling. Before beginning this tour, I desire to emphasize the debt this country, and particularly our mining industry, owes to that body of trained and experienced men, little heard of, but who, working quietly on their problems, are responsible for these improvements. The metallurgists, to whom I refer, have solved many difficult problems for the mining industry, in connection with the treatment of our complex ores; for instance, the silver-cobalt ores of the Cobalt district, the gold ores of the Porcupine district, the gold-telluride ores of the Kirkland Lake? district, the copper-gold ores of Noranda, the arsenical-gold ores of the Beattie mine, the copper-zinc ores of Flin Flon, and the lead-zinc ores of Kimberley. In doing so, they have maintained the high technical standards of the profession, and the practices thus evolved are noteworthy for their high degree of efficiency. When the price of gold increased from $20.67 to $35.00 an ounce, what had formerly been thought to be a low tailing became almost an ore, so that the metallurgists are now busily engaged upon the problem of putting this railing back in its proper place of being a tailing once more, or from its value, at the present price, of anywhere from 50 cents to a dollar or so per ton, to a few cents per ton. Owing to the changing prices of the metals in the world's markets, still greater improvements in metallurgical practices are imperative. An important contributory factor towards improvement in ore dressing is the aid furnished by the microscope in the examination of ores and mill products. By making possible the determination of the mineral constituents of the ore, their association, and grain size, it gives the investigator a knowledge of his problem, before he does any actual test work. In the Mines Branch laboratories at Ottawa, its use has enabled us to predict how an ore should respond to various methods of treatment.

Jan 1, 1935

By P. Ashtari

Influence of Sr and Mn single and combined additions on the modification of the Fe-containing intermetallic compounds and mechanical properties of Fe-rich AA319 aluminum alloys have been investigated, The microstructural features e,g, morphology of the Fe compounds and eutectic Si has been correlated to the mechanical properties, It was demonstrated that modification of the Fe compounds from the platelet ß-Al5FeSi to the Chinese script a-Al8Fe2Si compound improves the UTS and elongation of the alloys by 10.3% and 83.9%, respectively. Moreover, the simultaneous modification of the Fe compounds and eutectic Si increases the UTS and elongation of the alloys by 15,3% and 116,1%, respectively.

Jan 1, 2005

By J B. McConnell

The Thompson smelter has three unique features which form the basis ~f its design: fluid bed roasters which treat nickel concentrate filter cake from the mill, as well as the flux, in order to achieve partial desulphurization; the use of electric furnaces for the smelting of the partially desulphurized, preheated roaster product; and the disposal of slag by water granulation and slag slurry pumping. The installation consists of three fluid bed roasters, each feeding an electric furnace. Nickel concentrate is received at the smelter via pipe line. It is thickened and filtered, and the filter cake, together with siliceous flux, is fed through rotary bin feeders and reciprocating double-gate seals into the fluid bed roasters. Air injected into the roasters through club-head tuyeres oxidizes part of the sulphur and associated iron in the concentrate. The heat of reaction dries and heats the charge. Roaster product is recovered from the gas stream in cyclones and from the roaster bed through automatic valves.

Jan 1, 1963

By K. Eklund, T. Ahokainen

The Flash Smelting process is the most used production method for primary copper in the world. The basic idea of the Flash Smelting is to utilize the thermal value of sulfidic concentrates and melt the reaction product, in controlled conditions, without a need for external energy. This basic principle is utilized both in matte smelting and in Direct-to-Blister Flash Smelting Processes. In this paper, the behavior of normal (CuFeS2) concentrate of FSF-process is compared to the behavior of high grade feed material produced by Outokumpu Concentrate Upgrade Process with the aid of computational fluid dynamics (CPD) simulation using add-in subroutines developed by Outokumpu Technology. Results consist of the information concerning the behavior of the suspension, reaction efficiency and other parameters concerning the reactions of the feed material. It will be shown that, using the Upgrade Process, the throughput of copper from the Flash Furnace can be almost tripled.

Jan 1, 2007

By R. White, C. Doyle, B. Martin, C. Díaz, J. Hrepic, G. Cuthbert

"A program initiated to improve the service life of the magnesite-chrome refractory in the top blown rotary converters at INCO’s Copper Cliff Nickel Refinery identified slag corrosion as a major wear mechanism. Target slag compositions were established to produce a non corrosive slag. A plant program to achieve this target slag by the addition of controlled amounts of do lime and MgO was instituted. Addition to rates of the slag modifiers was optimized based on the slag composition assays achieved and the requirement to address corrosion effects on the high alumina content ladle refractory. A60% gain in TBRC refractory performance was eventually achieved and has been maintained yielding a net annual savings of $700,000. A significant gain in available converter operating time has also been realized.IntroductionINCO’s Copper Cliff Nickel Refinery utilizes two top blown rotary converters (Fig. 1) to smelt a blend of semi-refined nickel concentrates, producing a granulated nickel matte suitable for the adjacent carbonyl based nickel refining operation. The converter, or TBRC, operation is a batch process composed of feed charging and melting, oxidation of the excess sulphur in the matte, and reduction of residual nickel oxide. The final matte, containing about 78% nickel, is tapped at 1600°C from the converter and is granulated in a sluice equipped with high pressure water jets."

Jan 1, 1997

By A. G. Matyas

Process improvements which have reduced the lead content of slag from the Brunswick lead blast furnace are described. Microscope examination and electron microprobe analyses, supported by the results of slag settling and viscosity tests, showed that typically about 70% of the lead in the lead blast-furnace slag was present in the form of entrained prills of metallic lead. The total lead content was found to increase with the magnetic susceptibility of the slag. Measurements in the furnace settler indicated the presence of a magnetite-rich layer between bullion and slag, arising from high magnetite levels in the slag. This layer was believed to inhibit the settling of entrained lead from the slag. Tracer tests showed that the average slag residence time in the settler was less than 2 minutes. Improvements in coke quality and sizing, which led to a reduction in the slag magnetite content, and the installation of a larger settler and a continuous Roy tapper, have all contributed to a significant decrease in the slag lead content.

Jan 1, 1977

By J. A. Finch

Individual mineral cyclone performance curves were determined for the four major minerals at two lead-zinc concentrators. Sizing was by screen and cyclosizer down to approximately 10 um, with lead , zinc and iron as saying of each size fraction. The performance curves were similar in shape and located according to the mineral specific gravity, Pm. The curves displayed a discontinuity at the fine end and a magnitude of short-circuiting of fines to the underflow which increased with Pm. Mass fraction of water to the underflow was only a guide to this short-circuiting. Sharpness of separation seemed in dependent of Pm. An inflection in the over-all performance curve was shown to be a consequence of the individual component mineral performance. A general relationship was observed showing that the flow regime of classification changed from laminar/ intermediate to turbulent with increasing cyclone feed size. Individual mineral size reduction for the four major minerals at one of the concentrators was also determined. Size reduction of the silica was greater than that of the galena, in contradiction to their accepted relative grind-ability. The observation did correlate with silica being much coarser than the galena in the feed to the ball mill. It is suggested that the silica acted as a buffer to the galena.

Jan 1, 1977

By G M. Young

IT IS most appropriate that this first Memorial Lecture should be given in the Province of Quebec, near the site of the first metallurgical industry in Canada. At La Forge, about seven miles north of Three Rivers, iron was produced in 1783. We are told that the early settlers obtained most of their iron-ware -stoves, kettles, axes and ploughshares -from this smelter, with its foundry and forge. The Canadian copper industry also had its beginnings in Quebec when, nearly 100 years later, in the 1880's, several small copper smelters were erected in the Eastern Townships. Later, in 1899, Canada's first aluminum smelter was built at Shawinigan. From these small beginnings has grown a vast metals industry, the export value of its products being only exceeded by that of our forest products -newsprint, pulp-wood and lumber. As we are not a large country in terms of population, our domestic capacity to consume is often small in relation to our developed capacity to produce.

Jan 1, 1963

"Bay d'Espoir is in the approximate center of the south coast of Newfoundland. The geology of the area can most conveniently be considered in terms of three units: (1) an Ordovician or older polydeformed terrain termed the Little Passage Gneisses; (2) a Lower-Middle Ordovician volcano-sedimentary sequence assigned to the Baie d'Espoir Group; and (3) granitoid intrusive rocks of mid-Paleozoic age. Mineralizing events accompanied the formation of the latter two units.The Baie d'Espoir Group comprises a dominantly sedimentary sequence of pre-Middle Ordovician shelf and distal turbidite sediments deposited on the eastern margin of Iapetus. A significant volcanic component is, however, present in the Isle Galet Formation, consisting of up to 30% felsic volcanic rocks interbedded with sedimentary and epiclastic rocks. The Isle Galet Formation hosts several disseminated to thinly bedded Pb-Zn-Ag occurrences associated with altered felsic tuff and graphitic shale. They occasionally grade laterally into pyrite iron formation and appear to have been deposited in a very distal volcanic environment. The Isle Galet Formation is a time equivalent of the mineralized pre-Caradocian island-arc sequences of central Newfoundland, but differs from them both in style of volcanism and in the nature of the associated mineral deposits. It is, however, comparable in many respects to mineralized volcanic sequences in the La Poile Bay area of southwestern Newfoundland.Mineralization associated with granitoid rocks in Bay d'Espoir is best developed around the southeast margin of the North Bay Granite, where two-mica leucogranite forms a marginal phase. Numerous minor base metal showings occupy quartz, quartz-carbonate and barite veins in the adjacent sedimentary rocks. Collectively, the showings exhibit a well-developed, zonal pattern around the granite margin; molybdenite (±py, cpy) predominates near the contact, giving way outward to galena (±sph, py, asp, cpy) and eventually to stibnite (±asp, py) at the periphery. Mineralization associated with granites in similar settings elsewhere in southern Newfoundland includes tungsten in the Grey River and Granite Lake areas and molybdenite in the Rencontre Lake area."

Jan 1, 1982

By G. S. Ospanova

The results of complex processing sulphide copper ore and advantages of recovery of copper by vat and heap leaching, sorption, cementation and electrolytic solutions processing and utilization of waste material after heap leaching of copper for production of building materials were investigated. The combined chemical solvents with the additives of oxidizing agents are developed at the KazNTU. The solvents are inorganic or organic chemical reagents, which form complexes of Cu, Au, Ag, Pt, Ni, Sr, Co etc. Recovery of non-ferrous metals from solutions and purification of industrial waste waters is carried out on the base of using new synthetic and natural sorbents (from local raw materials) which are able to bind ions in both cationic and anionic forms depending on type of ligands and external conditions. Optimum parameters of copper sorption were determined. The developed wasteless technologies of copper extraction from sulphide ores with usage of new non-toxic solvents and accessible sorbents with full recycling of water are tested in pilot scale heap leaching, and are recommended as the ecological, economical and practical alternative to traditional methods.

Jan 1, 2007

By J. R. Jutras, C. Brissette, J. Champagne

"Pure cadmium sulphide was leached by the action of the bacterium Thiobacillus thiooxidans in the presence of finely divided sulphur. The influence of time, temperature, pH and concentration of inoculum on the extent of the cadmium extraction was studied. Under optimum conditions, up to 72 per cent of the cadmium could be dissolved over a six-week period. A cursory study of the role played by elemental sulphur seems to indicate that its presence is essential but that the sul1>huric acid produced through its oxidation is a minor factor in the cadmium extraction."

Jan 1, 1971

By J. Desrosiers

"Minnova Inc. has five operating divisions thoughout Canada. One of them is Lac Dufault which was established in 1964.Lac Dufault is located 15 km north of Rouyn-Noranda, in what is known as Noranda volcanic centre, in northwestern Quebec. For more than 25 years, Lac Dufault has produced copper, zinc, gold and silver from four different mines: Norbec, Millenbach, Corbet and now Ansil.Ansil, officially in production since July 1989, is one of the deepest mines presently in production in Quebec. This high-grade copper, gold, zinc and silver orebody is being mined at a rate of 1200 tonnes per day with a total workforce of 200 employees.Of particular interest are the high mechanization level of the underground mine, technical innovations also underground, and computer applications throughout the division.IntroductionMinnova Inc. was formerly known as Corporation Falconbridge Copper until 50% of its shares were bought by Kerr Addison Mines Ltd . in 1986 and it became a member of Noranda Group of Companies.Minnova stands for mining innovation. It means Minnovaaims to use state-of-the-art technologies in mining and exploration to achieve maximum efficiency and cost effectiveness. It also means that they aim to use both proven and innovative management principles to the optimum benefit of their employees and shareholders. Minnova has operations across Canada. Presently four mining divisions produce copper, zinc, gold, silver and lead. Two are situated in Quebec: Lac Dufault (established in 1964) and Lac Shortt (established in 1985); one in Ontario; Winston Lake (established in 1988); and one in British Columbia; Samatosum (established in 1989).Minnova has an annual exploration budget of $15 million divided 60/40 between base metals and precious metals. Most of Minnova's exploration efforts are concentrated around their existing mines. Exploration is carried out from six regional offices located at Rouyn-Noranda and Chapais in Quebec; Thunder Bay in Ontario, Vancouver in British Columbia, Reno, Nevada in the United State and Panama City Panama. Each of the Canadian offices maintains close liaison with nearby operations.Lac Dufault Division is located in the Noranda mining camp, approximately 15 km north of the city of Rouyn-Noranda, in northwestern Quebec (Fig . 1)."

Jan 1, 1991

By H. R. McCabe

"The study of a detailed series of structure and isopach maps of the Palaeozoic strata of southwestern Manitoba indicates that the principal Palaeozoic tectonic elements -the Williston Basin and Elk Point Basin -have been modified to a considerable extent by major tectonic features of the Precambrian basement. The principal basement feature is the break between the Churchill and Superior provinces, which coincides roughly with the Manitoba-Saskatchewan border. East-west-trending orogenic belts within the Superior crustal block may also be reflected to some extent in later Palaeozoic movements. In addition, the Superior crustal block, as a whole, appears to have had a slightly different response to the tectonic forces, giving rise to both basin subsidence and basin uplift. During periods of deposition, especially during Ordovician time, the Manitoba portion of the basin appears to have undergone a relatively higher rate of subsidence, whereas during periods of erosion relatively greater amounts of uplift and truncation have occurred. As a result, the depositional and erosional patterns for most of the Palaeozoic formations in southwestern Manitoba are somewhat anomalous relative to the regional basin framework.Some prominent Palaeozoic structures probably are the result of salt solution and differential compaction caused directly or indirectly by relatively minor tectonic movements related to Precambrian basement features. In particular, the prominent hinge line at the edge of the Devonian Prairie Evaporite salt basin may be due, in large part, to salt solution. Numerous other small structural lows, structural highs and isopach thicks, probably resulting from salt solution, occur along the salt edge and have been important in modifying and controlling Mississippian oil accumulation in the Daly-Virden producing area."

Jan 1, 1967

By A. P. Craig

"I HAVE BEEN looking forward to addressing this particular audience about Trans-Canada Pipe Lines because you men, more than most, understand the problems of the pioneer. Trans-Canada Pipe Lines qualifies as a pioneer on two counts: it is certainly pioneering a completely new industry in Canada -the long-distance transmission of natural gas -and it has at least a few of the problems that are expected and normal to any pioneering venture.This morning, I’m going to try to give you a sketchy picture of our project and a brief report on its current status and our progress to date; and then a broad picture of Canadian markets for natural gas.The physical characteristics of the Trans-Canada Pipe Lines project have been discussed so often that I am not going to take the time today to quote a lot of statistics on pipe sizes, miles, tons of steel, etc. Suffice it to say that this project, estimated to cost approximately $350,000,000, will be the longest large-diameter gas pipe-line ever built anywhere.Let me try to paint a broad picture of this great national project, using only a few basic 'round' figures.First, it involves exploration for and development of the natural gas fields in Alberta and other provinces -the cost of which will run into hundreds of millions of dollars.Then comes the gathering, stripping, and cleaning of the gas before it can be delivered to Trans-Canada. This will cost close to $100 million.Next we have the Trans-Canada Pipe Lines project for transmission of the gas to Eastern markets -estimated to cost $350,000,000 during the first three to four years and making natural gas economically available to one-half the population of Canada."

Jan 1, 1955

By D. Roy Eccles

A multi-element geochemical response, with contrasts of up to 29 times background, was obtained in soil above the Mountain Lake Diatreme, northwestern Alberta. The overall geochemical signature is indicative of an ultramafic source; geochemical responses contain elevated concentrations of Co, Cr,O, Cu and Ni with the presence of high Ba, Ga, HI, PO,, Rb, Ta, Ti and light rare earth elements suggestive ofa kimberlite or lamproite body. The shape, or morphology, of the enzyme leach-based geochemical signature over the Mountain Lake Diatreme combines moderately strong to strong oxidation halos, or a rabbit's- ear geochemical profile, with a sharply-defined apical geochemical profile. Because some Alberta diatremes discovered to date form positive topographic highs, the resultant geochemical signature may express the soil development profile that forms directly on top of kimberlitic and lamproitic bodies. The enzyme leach technique, which has proven to be a useful tool in base metal, precious metal and petroleum exploration, may have a significant impact on exploration for kimberlite, lamproite and related rocks in Alberta by providing industry with a useful and cost effective tool to probe blind and/or buried anomalies identified by airborne and ground magnetic surveys in areas of glacial overburden.

Jan 1, 2001