Search Documents

By Deepak Bhadouriya, Saurabh Singh, Aditya Raj Suman

"An experimental study of chemically enhanced filtration and dewatering of fine coal slurry with and without additives was carried out. The experiment involved determination of effect of slurry concentration, additives (cationic, anionic and nonionic), filter area, filtration velocity, particle size and cake resistance on dewatering and filtration using vacuum filtration cell. Finally, the rate of filtration and dewatering and optimum amount of additives used were determined under suitable filtration condition. Overall, it was found that the filtration and dewatering characteristics were enhanced by increased slurry concentration, larger filter area and larger particle size. In addition of additives, the kerosene was found to be best for enhancing the filtration which yielded cake moisture reductions of approximately 17% by weight. At optimum dosages, the final cake moisture contents were reduced by 3.6% and 5.8% by weight using the appropriate surfactant and flocculent, respectively.INTRODUCTIONFor India, it is estimated that coal constitute a principal source of energy for the next several decades. It is majorly used at thermal power plants to generate electricity and also to a great extent in steel and cement industry. It has been observed that its consumption is increasing so as to meet the energy requirements of the country. It has been found that in a coal preparation plant; approximately 20-25 percent coal is of the mined coal of the range below minus 0.5 mm (28 meshes). Generally, this fine fraction is discarded due to its high cost of processing and further utilisatisation is very minimal. But with ongoing research and development for advanced clean coal technology, various new techniques have been evolved to maximize the utilization of available coal. In recent time technologies such as column flotation, cleaning of fine size coal to lower the ash content and low pyretic sulfur is feasible at high recovery value. But in various researches it is found that one of the biggest hurdles in utilization of fine coal cleaning technology by the coal industry is the economic dewatering of the fine clean coal product. Thus, until an economical and practical solution to dewatering of fine clean coal is achieved, the efforts devoted to developing fine clean coal technology will be wasted. In this paper an effort toward enhancing and developing the optimum technique of dewatering and filtration of fine coal slurry has been made."

Jan 1, 2016

By J. Poplawski

In mineral processing plants, cyclones typically perform the classification duty prior to the downstream recovery process. Particle size distribution of the cyclone overflow is an important parameter and can be viewed as the product of the comminution process. Too coarse of a product will likely have poorly liberated valuable minerals and make recovery difficult. Too fine of a product may represent a missed opportunity to increase plant throughput and/or also result in low recovery due to poor kinetics. “Near-line” particle size measurement instrumentation has been in place for several decades, its availability and low measurement frequency have typically been inadequate for reliable use in automatic control. CiDRA Minerals Processing has developed a novel and robust technology that provides a highly reliable and low maintenance system for “on-line” measurement of the particle size in the overflow of individual cyclones. The system is based around a wetted sensor design with no moving parts and provides a real-time trend of the desired target grind size parameter. The system does not require sampling and associated sample transfer piping that is prone to plugging, thus avoiding high maintenance requirements. Plant data and benefits realized from the latest installations of the CYCLONEtrac PST will be presented. INTRODUCTION Impact-based real-time hydrocyclone particle size measurement Acoustic impact-based particle size tracking is a unique method for measuring and controlling the particle size in cyclone overflow streams. The implementation of this technology is centered upon a sensor probe that is inserted into the overflow slurry stream via a two-inch (50 mm) hole in the overflow pipe (Figure 1). Particles within the slurry stream impact the surface of the probe generating travelling stress waves within the probe. A sensor converts these travelling stress waves into an electrical signal and proprietary signal processing techniques convert these signals into a particle size measurement that is output every four seconds. The sensor is constantly in contact with many particles in the slurry stream, thus obtaining information from orders of magnitude more particles than traditional sample-based technologies. The sensor has no impact on cyclone performance because it is located downstream of the hydrocyclone and the presence of an air core ensures there is no change in the back pressure seen by the hydrocyclone.

Jan 1, 2019

By Emilie Williams

Introduction Mouska Mine, Doyon Division site Background and timeline Obstacles to standard paste delivery system Components of Mouska paste system Technical considerations Operational considerations Mouska Mine Underground gold mine 30 km east of Rouyn-Noranda, Quebec Part of Doyon Division, 100% owned by IAMGold Commercial production since 1991 Cumulative production over 850,000 oz Conventional mining until 2009 485 m shaft from surface 560 m internal shaft 500 tpd (ore and waste) Off-site milling Approximately 150 employees

Oct 1, 2010

By Ross Gallinger

In 1997 a group of Canadian mining companies met to review the Mine Environment Neutral Drainage (MEND) program and to consider future activities. They concluded (i) that Canadian industry and NRCan should fund a small secretariat in Ottawa to support technology transfer in Canada and (ii) that it was important for industry to continue the momentum of MEND on an international scale. The need for INAP (International Network for Acid Prevention) was strongly endorsed by company, university, consultant and government experts from Australia, Canada and the U.S. who were convened in Vancouver in February 1998. The initial focus was the development of a solid knowledge base covering the collective experience of INAP's members to promote the dissemination of successful practices, the identification of knowledge gaps and the formulation of effective research proposals. The sharing of information on past successes and failures alone was viewed as sufficient justification for the formation of INAP. INAP was officially launched in October 1998, and is now an effective, industry based initiative to globally coordinate research and development in the management of sulfide mine waste. Significant improvements in the management of sulfidic mine materials through knowledge sharing, research and development of technology by INAP will reduce liability associated with acid drainage. This paper will explore the international efforts and activities of INAP.

May 1, 2002

By Z. D. Hora

The major fluorite producer in British Columbia was the Rock Candy Mine, inactive since 1942. Other deposits of economic interest include the Rexspar deposit, in which fluorite is associated with uranium and rare earth mineralization, and the Eaglet and Liard River occurrences. THE former Rock Candy fluorite mine, located 26 km north of Grand Forks, is the only major past producer of fluorite in British Columbia. The deposit was in production from 1918 to 1929 and again in 1942; total output was about 36,000 tonnes with average grade between 22 and 32 per cent CaF2. The fluorite body occupies a steeply-dipping vein structure, approximately 175 m long and up to 12 m wide, in porphyritic syenite. The chief vein-filling minerals are quartz and fluorite with local small len ses of barite. Fluorite content decreases with depth and the deposit becomes silicified. The Rexspar (or Birch Island) fluorite deposit is located 130 km north of Kamloops. The deposit is complex with rare earth elements and high uranium values, but !1uorite mineralization forms an independent zone adjacent to the uranium orebodies. Fluorite is present as fine-grained impregnations and as breccia cement in strongly schistose or brecciated alkali feld spar porphyry. Reported reserves are 1,088,000 tonnes of 22 per cent CaF2 or 450,000 tonnes of 29 per cent CaF2. 268 Another potential deposit of fluorite is Eaglet, situated on the north side of Quesnel Lake. Fluorite occurs as a stock work with scattered veins and irregular lenses up to 20 centimetres wide and as impregnations in altered Proterozoic Kaza Group feld spathic gneiss over an area of 1,500 metres by 500 metres. To date (1983) approximately $2 million have been spent on the exploration of this property and reserves of 18.8 mimon tonnes grading 11.59 per cent CaF2 have been outlined . A group of significant occurrences is known from north of Liard River Hot Springs Park , where fluorite occurs in small zones up to 17 m thick along the interface between Middle Devonian Dunedin Formation limestone and Middle Devonian to Mississippian Besa River Formation argillite. Fluorite, associated with witherite, barytocalcite and barite, is present as replacement bodies, breccia fillings and minor veins.

Jan 1, 1984

By J. W. Merkley, K. B. Hustwick

"The authors describe the use of a computer system for the control oj warehouse inventory at Cominco's Canadian operations. The challenge presented by the company's diverse products and various locations necessitated a practical approach to operational and manpower requirements. The utilization of modern forecasting techniques, manual intervention and exception reporting provides system flexibility. The system also provides both operational and management control to set required service goals at the lowest inventory levels for inventory management.IntroductionCominco Ltd. is a Canadian company, with international operations, the principal business of which is zinc, lead and chemical fertilizer s. Its involvement is fully integrated and range s from mineral exploration through mining, smelting, refining and by-product production to international marketing. It also embraces related services, including trade, wharfarge and power. With head office in Vancouver, it is involved, directly or through subsidiary or associated companies, in Canada and in the United States, Greenland, Europe, Australia, India and Japan.Cominco has over 12,000 employees and 26,000 shareholders, with 91% of all shares held in Canada.Cominco's Inventory Control System is one of the most extensively used computer systems employed by the company. Also, inventory control is regarded as one of the most economically successful computer applications to be undertaken by the Data Processing Services (D.P.S) Group that was responsible for the development of the Inventory Control System.The main use of automatic inventory control has been at operating plants in Western Canada and the Northwest Territories, which are separated by large distances. Each location has equipment-intensive mining and processing operations and it is essential to maintain control of parts and supplies inventories. Some of these locations are remote from urban and industrial centres and it is important to avoid the adverse effects of high personnel costs and re-training due to turnover."

Jan 1, 1982

?Founded in 1969 by the Ruia family ?Diversified global business corporation with a balanced portfolio of assets in the manufacturing and service sectors; $15 Billion revenue in FY 2009-2010 ?Employs 70,000 people worldwide with offices in Asia, Africa, Europe and North America

May 1, 2011

By L. Bryson, J. H. W. M. Brits, K. Voogt

"The Anglo American Platinum’s Rustenburg Base Metals Refinery (RBMR) has the world’s first full deposit nickel plating tankhouse. Impurities in the nickel electrolyte can induce stresses in the electrowon nickel deposits that could lead to delamination of the deposit. Identifying the impurities that contribute to increasing internal stresses in the nickel deposit is key to successful operation and automation of the tankhouse. Impurities were introduced in the plant electrolyte and the effects on the full-scale nickel deposits evaluated. The impurity-adjusted electrolyte solutions were also analyzed using commercially available bench-scale methods to determine the induced stress. A correlation between impurity-induced deposit stress and full-scale delamination was developed. A direct correlation can now be made between feed quality, i.e. impurity concentrations, and degree of delamination in the plant. This methodology has the potential to rapidly predict the effect of new reagents, upstream process upset conditions and synergistic interactions between impurities on deposit stress and delamination of nickel deposits.INTRODUCTION Nickel electrowinning in sulphate media was first pioneered by Outokumpu in its Harjavalta refinery in 1960 (Saarinen and Seilo, 1985). The original process was very manual with starter sheets plated onto “acid resistant” steel for 36 hours and then manually stripped and cut into sheets which could be inserted into the main production cells for a further 4–5 days. The starter sheet stripping and manufacture process was later automated. The same technology was subsequently implemented on a number of plants around the world. Anglo American Platinum’s Base Metal Refinery (BMR) began nickel electrowinning in the early 1980’s. The recent expansion of Anglo American Platinum’s Base Metals Refinery necessitated the construction of a new nickel tankhouse to achieve two primary objectives. The first to increase the capacity to 32 400 tpa nickel and the second to reduce employee occupational exposure to nickel aerosols. The new tankhouse has been commissioned and is in the process of ramp-up; more details are given by Hagemann et al. (2016). Fundamental to lowering employee exposure to aerosols was automating both harvesting and final handling of cathode. In order to accomplish this a bold move was taken to plate up to 10 days on permanent titanium blanks which are harvested by automatic crane and automatically stripped. The original development work for the plating nickel on titanium blanks over a ten day cycle is given by Bryson et al. (2006)."

Jan 1, 2017

By J-P. Rossetti, A. Guerin, M. Jaboyedoff, L. Baillet, A. Mariscal, J. D'Amato, D. Hantz

"The processes leading to the fall of rock compartments from rock walls are poorly known as well as their velocity. It ensues that quantitative prediction of the failure time for a rock compartment which is presently stable, is not possible by a purely geomechanical approach. However a quantitative probabilistic prediction of rockfalls at the scale of a rock wall is possible if the spatial-temporal rockfall frequency can be determined or estimated (Hantz, 2011). For a better knowledge of failure processes and frequency, rockfalls have been detected in several rock walls, using annual terrestrial laser scanning, allowing comparison of the frequencies in different geological conditions. For one of these rock walls, the spatial detection have been completed by a precise dating of the events, using a quasi-continuous photographic survey (one photo every 10 mn), allowing the study of the influence of meteorological factors.The precise dating of rockfalls has been carried out for the Saint-Eynard cliff which towers above a residential area of the town of Grenoble (French Alps). The South-East facing cliff consists in bedded limestone gently dipping North-West and located at an elevation between 850 m and 1100 m. The surveyed zone is about 750 m large and 250 m high. Between 01/02/2013 and 26/11/2013, 65 rockfalls ranging between 0.01 m3 and 20 m3, have been detected by diachronic comparison of laser scanner data and dated by comparison of photographic images. The temperature at the elevation of the cliff has been calculated from the temperature measured (every 5 mn) at a meteorological station located at an elevation of 245 m and 2.5 km away from the cliff, using a temperature gradient of 0.003°C/m (D’Amato et al., 2014). The precipitation were measured 900 m away from the cliff at an elevation of 469 m. Different meteorological conditions have been defined: (a) “freeze” qualifies days with negative mean temperature (but with a thaw period, except for two days); (b) “thaw” qualifies days with positive mean temperature, but following a freeze day; (c) “rain” qualifies days with precipitation.Table 1 shows the rockfall temporal frequency for the different meteorological conditions. It appears that the frequency is about 6 times higher the freeze days, 2.5 higher the thaw days and 3 times higher the rain days than days without freeze, thaw or rain."

Jan 1, 2015

By R. F. Tylecote

"The closure of the iron and steel making plant at Consett in Durham in 1980 marked the end of an era-a long era in the world's iron and steel making history. Iron had been smelted in the Tyne-Wear area of the United Kingdom since before the Roman period, but apart from evidence of smithing in the Roman period, the historical evidence for iron production on a large scale dates from the 14th century.The paper describes sites in the area that first worked the bloomery process and then, in the 16th century, as did most of Europe, graduated to the blast furnace process. The main emphasis is on the early introduction of coal to iron making at the end of the 18th century and the use of the steam engine to render integrated sites possible.IntroductionIron has been smelted in the Tyne-Wear area of the United Kingdom since before the Roman period, but apart from clear evidence of smithing in the Roman period, the historical evidence for iron production on a large scale dates from the 14th century. Like many other countries, the United Kingdom benefitted from the visits of foreign observers, such as Jars, Svedenstierna, de la Houliere and Dufrenoy, who left detailed records. In modern times, information gained from excavations of iron and steel making sites has supplemented the historical record.Natural ResourcesUp to the end of the 19th century, the industry was wholly dependent on its own resources. Iron ore, limestone, wood, coal and water power were all found a short distance away from the main valleys of the Tyne and Wear. The main sources of iron ore were the coal measures, with rider ores from the lead vein s in Alston and Weardale, and carbonate ores from shale horizons in the Carboniferous limestone. Good coking coal was available from West Durham and reasonable coal from the Tyne valley and Northumberland limestone. Limestone was plentiful."

Jan 1, 1983

By J. E. Udd, L. P. Geldart, B. B. Dhar

"Solutions for the stress distributions around simulated underground openings have been limited to calculations of boundary stresses for simple openings in which the boundaries may be expressed in mathematical terms. Studies involving circles, ellipses and ovaloids are re-ported in the literature.The stresses on the boundary of an opening and those at a distance from it in the medium are of concern to the engineer. The former may be related to the greatest concentrations of stresses encountered; the latter have a bearing on the identification of the ""zone of influence"" of the opening.Recent advances, in the form of a derivation for the stresses at a distance from an opening of elliptical shape, together with a solution derived previously for stresses in depth around ovaloidal openings, have been combined with computer programming techniques to provide complete solutions for a wide range of cases and variables. Some typical results which, it is hoped, may have some application to the design of underground openings are given herein."

Jan 1, 1970

By Fan Delian, Ye Jie, Lui Tiebing

The lower and the upper parts of the Doushantuo Fonnation, Hubei Province, China, contain silicate-type K-rich beds (illite and feldspar), and intraclastic phosphorites, as well as Ag-V and V deposits in a "Black Shale Series". The K-rich beds fonned in an anoxic basin whereas the phosphorites fonned in a more oxic and higher energy depositional environment. The Black Shale Series occurs in the lower and upper parts of the Doushantuo Fonnation; that in the upper part consists of black illite shale and dark gray dolostone, and contains Se-rich Ag and V deposits. These deposits are of more industrial significance than the previously discovered Ni-Mo polyelement sulfide deposits which occur in the Lower Cambrian Black Shales Series of South China. Studies of lithotype, sedimentary sequence, and geochemistry of the Doushantuo Fonnation have led to more attention being focused on the uppennost Black Shale Series and its Ag-V and V deposits. There are three ore types: black, Ag-V-rich, illite shale; black, V-rich, illite shale; and dark gray, Ag-Vrich, fmely crystalline dolostone. The first two ore types contain 3070 to 5% Corg and the last, 1.25%. The Ag-bearing minerals are naumannite, argyrodite, aguilarite, acanthite, and native silver that occur as inclusions in pyrite associated with barite. Vanadium substitutes for AI in illite and is also related to organic-matter contents. Because (1) the pre-Sinian Kongling Group contains one to three times greater than the Clark Ag value; (2) black, illite shale has a negative Ce anomaly; and (3) there are large occurrences of black, K-rich, tuffaceous, fme siltstone, the sources of Ag are thought to include subaerial and submarine volcanic materials. It is proposed that Ag, V, and Se were absorbed by clay particles and organic matter during syngenetic deposition in an anoxic environment; Ag subsequently was reconcentrated into sulfides and selenides, whereas V was incorporated structurally into illite during early and late diagenesis. These types of Black Shale Series-hosted Ag-V and V deposits are, therefore, considered to be sedimentary-diagenetic in origin.

Jan 1, 1992

By T. E. W. Nind

"A short description of the chamber lift method for producing oil wells is followed by some comments on compressor requirements and gas utilization. A quantitative analysis of the process is presented and, based on this analysis, criteria are suggested for selecting wells for which this type of lift might be suitable. The analysis leads to the conclusions that chamber lift is an efficient producing mechanism for wells having very low productivity indices (say about 0.05 bbl/d/ p.s.i. or less), but that for such wells optimum utilization of injection gas cannot be attained. It is suggested that the gas injection time per cycle should be kept as low as possible, compatible with a small oil fallback volume, and that the cycle frequency should be in the range of 20-40 cycles/ day. For wells with productivity indices of 0.2 bbl/d/p.s.i. or higher, chamber lift is relatively inefficient; how-ever, if well allowables are low it may offer an attractive, low cost, alternative to gas lift or pumping."

Jan 1, 1960

By L. A. Nazarova, M. Vandamme, L. A. Nazarov, R. I. Rodin

"The paper describes a new method of interpreting the “canister test” data for the quantitative estimation of gas-kinetic parameters of coal bed based on the developed model of gas emission from coal sample placed in a sealed container. The model accounts for grain-size composition of the sample, initial gas content S, as well as coefficients of diffusion D and mass transfer ?. The inverse coefficient problem is formulated to find S, D and ??from the data of pressure measurements in the sealed container. It is shown that the inverse problem is uniquely solvable if the pressure is dropped during the experiment. The method has been tested using the data from an underground coal mine in the Kuznetsk Basin.Based on the poroelastic model of a coal bed and Khristianovich’s concept about origination and evolution of the filtration zone F in the neighborhood of a degassing borehole the authors considered the corresponding direct problem on rock mass geomechanical state. It was offered interpretation method for data on pressure measurements in a plugged degassing borehole allows evaluation of the diffusion coefficient, the horizontal component of natural stress field and parameters of F. The related inverse problem of the mixed type is formulated, and the cost function is constructed. The analysis using synthetic input data has shown that the cost function has a number of local minimums arranged on the same straight line, one of the minimums being the inverse problem solution. INTRODUCTIONPre-mine degassing is an integral part of coal mining. It allows mitigation of induced accidents in mines (coal and gas outbursts, rock bursts) (Guide, 1990; Malyshev & Airuni, 1999; Seidle, 2011) and also furnishes an alternative and ecology-friendly energy source—methane (Rice, 1997; Nambo, 2001). Choosing an optimized pattern of degassing boreholes, as well as estimating degassing time and amount of gas recovered requires data on gas-kinetics indices of coal beds out of which the key parameter is a gas content S. According to the latest guidelines for coal mines in Russia (Ruban et al, 2012), mining is allowed if S in a coal bed section is under 7 kg/m3."

Jan 1, 2015

By Thom Sedun

No sector of the mining industry is more closely tied to local communities than aggregates. Noise, dust, traffic, visuals aesthetics and environmental impacts all fall under the purview of neighbours, local governments and nongovernment organizations. It is no surprise that aggregate operations may not be welcome neighbors in many communities. In British Columbia (BC), the regulatory environment for aggregate operations includes a local component of municipal bylaws and land use-planning in addition to the usual suite of federal and provincial statutes that apply to its sister mining sectors. Additionally, under common law aggregate extraction is not considered to be a land use subject to land use zoning, and some aggregate processing activities can be regulated by zoning. Often traversing multiple local government jurisdictions, aggregate producers find themselves negotiating not only local traffic, but also a mosaic of regulatory environments. There is an opportunity in this present situation to facilitate the application of current technology and practices in the mitigation of many community and environmental concerns associated with aggregate operations. Moving a bulk commodity is a volume-based business, and operators often don?t have time for matters that don?t directly or obviously affect the bottom line. Regulatory agencies often play multiple and complex roles with respect to their industry, not the least of which is the fiduciary role. Balancing how and when to assist an industry is often a difficult decision. For the aggregate industry in BC, the Ministry of Energy and Mines saw an opportunity to assist not only aggregate operators, but also regulatory agencies, local governments, and the general public. Through investing in the Aggregate Operators Best Management Practices Handbook (handbook) project, the Ministry of Energy and Mines (MEM) believes that it will realize a return of upheld community values, enhanced environmental protection, improved regulatory compliance, reduce disputes and a stronger provincial aggregate industry. It is the intent to publish the handbook electronically through the MEM website later this year.

May 1, 2002

By Richard J. Kolada, Ian R. Muirhead

"This paper reports on a CANMET-funded examination of less conventional underground coal mining methods. These methods are documented and those that show the most promise for application to western Canadian conditions are discussed in detail.IntroductionIn recent years, mining considerations and economics have encouraged a transition from underground mining to surface mining. However, a change in market conditions or the development of superior underground mining methods may reverse this trend . Should this happen, the industry must be quick to respond and have information available on the latest developments of underground mining technology. In time, deposits of high-quality coal, which are easily accessible to surface mining, will be depleted and a change to underground mining methods will require consideration. The economic transition point between surface to underground will be a major determinant in maintaining a competitive edge. For these reasons, it is important to keep abreast of improvements in underground mining methods. To meet this objective, CANMET awarded a research contract to Monenco Consultants Limited, to investigate unconventional underground mining methods that show a potential for western Canadaoi. This paper presents the results of this investigation."

Jan 1, 1988

By N. Morrison, I. Holl, R. Welyhorsky, A. Hempstock

ABSTRACT: The Victor diamond mine is located in the James Bay lowlands, 90 km west of the First Nations village of Attawapiskat. The project was the first of its kind in northern Ontario. The process plant was designed to produce a 95 to 98% by weight diamond concentrate through three stages of comminution, dense medium separation, and proprietary X-ray technology for final recovery. The plant was commissioned over a period of six months, commencing prior to substantial completion of construction. Through effective planning of the commissioning phase, the Victor mine start-up was safely completed nine months ahead of schedule.

Jan 1, 2011

By W. H. MacLean, P. J. MacGeehan, A. J. Bonenfant

"The Norita deposit is an Archean volcanogenic-exhalative Fe-Zn- Cu sulphide accumulation of the distal type, consisting of six overlapping stratiform massive sulphide lenses, interbedded with exhalative cherts and thin pillow basalt flows, which formed down-topographic-slope from a mineralized hydrothermal discharge zone in the Norita rhyolite. The sulphide lenses are of two main types: channel-fill deposits such as the Main Zone and Main Zone West, composed of intricately layered pyrite-sphalerite-chert, which formed by the dynamic down-slope transport and re-deposition of sulphide exhaled from the vent zone; and stratiform lenses such as the Cu-rich A-Zone and A-Zone West, which formed even farther down-slope, in basinal depressions flanking the dome. Although rotated into a vertical position by folding, the sulphide lenses are otherwise essentially undeformed and contain a wide range of preserved primary sedimentary structures.Of prime importance in exploration has been the recognition that the formation of the distal sulphide lenses was controlled by submarine paleotopography, and that it is possible to approximate the sea-floor paleotopography using variations in the thickness and strike extent of the interbedded volcanic rocks. This has proved to be a major and successful exploration tool in the search for further sulphide mineralization in the mine, and offers prospects for use elsewhere in the district."

Jan 1, 1981

By Graham E. Brown

Since the beginning of time, people later to be known as engineers and architects have strained to create methods whereby they could improve technology to assist them in their various fields of endeavour. Some of these improvements would be the change from linen paper, french chalk and ink pens to drafting film , mylar an d pencil for the production of drawings, the drafting machine in lieu of the tee and set squares, even tap e to attach drafting media to the board instead of thumb tacks and man y, man y more. All of these taken individually are insignificant but combined evolve to the current state-of-the-art in the computerized engineering environment. Ten years ago the major topic o f conversation was the hand-held calculator which for a cost of around $150 would give most trigonometric functions. Today the equivalent calculator can be purchased for around $25, is about one third the size, and if inflation were included over the last ten year s the item should cost around $550 in today' s dollars, it can be seen that tremendous advances not only in the technology but also the cost saving. The following paper is intended to outline some o f the significant aspects o f the latest technology in the computerized engineering office namely Interactive Graphics Systems.

Jan 1, 1985

By Rob Assabgui

Presentation Overview ? Stobie Mine Sublevel Cave Background ? Elevated Silica Levels ? Silica Control ? Challenges and Issues ? Conclusions

Oct 1, 2010