Search Documents

By G. Danha, D. Glasser, D. Hildebrandt, N. Hlabangana

"In this work, we apply a method known as the attainable region (AR) technique in order to optimize the milling and leaching process of a low grade gold ore. No work on the application of the AR optimization technique has been done yet on a joint milling and leaching process. The advantage of the AR approach lies in its ability to simplify the optimization problem, as searching over a defined set for the maximum of an objective function is a fairly standard procedure. The objective function we selected was that of optimizing a linear function of the value of the recovered material minus the cost of both milling and leaching. Using the three variables (milling time, leaching time and recovery), we constructed a 3D plot and used it to obtain all the possible recoveries from the different milling and leaching times. The optimum for our chosen objective was then found by overlaying a contour plot of the objective function on the 3D plot. Our results show that the optimum was obtained at 90 % recovery with a profit value of 600, milling time of 30 minutes and leaching time of 1750 minutes.INTRODUCTIONAfrican countries are facing a general increase in demand for electrical power. In South Africa, the demand is now surpassing the supply from ESKOM, the main electric power provider of the country. This has resulted in load shedding strategies being implemented in many local communities in an attempt by ESKOM to cope with the high demand. A potentially better approach is to propose use of energy efficient technologies in the country’s largest power consuming industry; the mineral processing sector.In mineral processing, milling is the highest consumer of energy. The objective of carrying out milling is not merely to reduce the particle size of the feed material, but also to liberate the constituent minerals that make up an ore. This is done so that valuable minerals can be separated from the gangue, in downstream processes, such as leaching. However, the milling process is generally performed relatively poorly, and at a considerable expense in terms of electrical power utilization. Tomanec and Milovanovic (1994) estimated that milling accounts for more than 50 % of the total power used in the concentration process, but this can rise to as high as 70 % for hard or finely dispersed and inter-grown ores. Apart from being relatively wasteful of energy, the milling process is also inefficient with regard to mineral liberation because of the indiscriminate nature of the grinding force."

Jan 1, 2016

By David H. Searle

This paper will discuss the common trends existing in various Canadian jurisdictions for the closure and reclamation of mines. Included will be a discussion of the requirement to post security as well as its form and how security is calculated and refunded. Reclamation can no longer be left to the end of mine life. Progressive reclamation must occur throughout mine life and must be part of the mine plan from the beginning.

May 1, 2006

By E. M. Stiles

THE Wellington Lake power plant of the Consolidated Mining and Smelting Company of Canada, Limited, about 25 miles from Goldfields, Saskatchewan, is the second hydro-electric project operating in that Province, the first being the Island Falls plant of the Churchill River Power Company which serves the operations of the Hudson Bay Mining and Smelting Company at Flin Flon, Manitoba. The Churchill River project develops 90,000 h.p. at 56-ft. head; the Wellington Lake plant 3,300 h.p. at 75-ft. with pro-vision for an additional 3,300 h.p. unit. Churchill River power is trans-mitted at 110,000 volts over a 58-mile line of steel towers to Flin Flon and an additional 45 miles over a wooden pole-line to Sherritt-Gordon. Our steel tower-line is 22 miles long, and the voltage is 60,000; this choice be-cause certain such equipment was available from Trail. The diversion of 15,000? second-feet at 56-ft. head for 90,000 h. p. at Churchill river dwarfs our 500 second-feet flow at 75-ft. head for 3,300 h.p. In both cases, the main obstacles to be overcome during plant construction were the lack of transport facilities and the short open season. Let it be noted here that this paper deals mainly with those phases of plant construction which were particularly interesting to the writer. With-out these variations from the ordinary routine, this is just another power project whose story is better told by the accompanying charts and pictures. To many members of the Institute it is still just that; but I am writing for those who, like myself, have been too seldom responsible for major under-rakings at an appreciable distance from a railway siding. When it was planned in early 1937 to erect a 1,000-ton mill at our Box mine, both hydro and Diesel power were discussed. With ten years' ore in sight, even an expensive hydro project, such as ours turned out to be, produces kilowatts materially below the 2-cent operating cost of a Diesel plant using fuel-oil at 14 cents a gallon.

Jan 1, 1940

By Y. Q. Li, Z. C. Shen, C. H. Zhao

The dynamic properties of the KYF-320 flotation machine which is one of the biggest flotation machines in the world were tested and then verified by the computational fluid dynamics (CFD) simulation. Aeration rate testing results suggest that he effect of circulation holes on the fluid state in the flotation cell becomes gradually smaller when the impeller speed is greater than 107 r/min. The dispersion degree of air increases with the increasing impeller speed and decreases with the increasing aeration rate, and it increases slightly when the impeller speed is greater than 107 r/min. The air holdup increases and then decreases with the increasing impeller speeds and aeration rates, and a maximum value of air holdup is shown at impeller speed of 107 r/min with a value of 12.28%. CFD simulation results are in good agreement with these testing results. Industrial-scale test was carried out using this 320 m3 flotation machine for the flotation of Cu ores. The results show that Cu content increases from 0.06% of crude ore to 1.26% of concentrate, and the S content increases from 0.39% of crude ore to 24.83% of concentrate. Moreover, using this flotation machine 5.88% of power is saved compared to other type of large flotation machine.

Jan 1, 2015

By C. A. Sutherland

"Smelting of copper-gold ore from nearby Rossland mines started at Trail in the 1890s. As ore from the Rossland mines became exhausted, lead smelting of hand-sorted galena ore from other British Columbia mines was initiated. With the development of flotation technology for the separation of lead, zinc, and iron sulphides in the first two decades of this century, the large Sullivan orebody at Kimberley, British Columbia, became the f oundation for the growth of a major zinc and lead smelter at Trail. Lead smelting began in 1901, electrolytic zinc in 1916, and by 1984, the Trail metallurgical complex had produced 10 million tons of each metal. Its present capacity is 270000 tonnes per year of zinc and 110 000 tonnes/year of lead.This paper reviews the history of technological changes in the Trail production plants, emphasizing the zinc plant modernization program started in the 1970s, and also the planned introduction of the QSL oxygen lead smelting process in the late 1980s. Lead modernization will increase production capacity to a maximum of 160000 tonnes per year.IntroductionCopper-gold ore was discovered at Rossland, British Columbia, in the year 1890, starting a mining industry that was to last over three decade s. Selected ore was at first transported at high cost to distant U.S. smelters, so there naturally followed a decision to construct a small copper smelter to process the local ore to matte. It was built in 1896 at the mouth of Trail Creek on the Columbia River, about 10 km from Rossland. This little smelter was to develop and diversify in the next 90 years into the world 's largest lead-zinc producer).The mining boom that occurred in the northwestern United States and southeastern British Columbia in the period of 1890 to 1910 saw the brief operation of many small local smelters. The only one to survive was the smelter at Trail. The circumstances that permitted its continued life and subsequent growth, form a fascinating history of business deals, litigation, andsteady technical progress.Early investment in local railway transportation and options by F.A. Heinze, the smelter' s founder, attracted the attention of the Canadian Pacific Railway Company, which purchased Heinze' s assets in 1898. This provided the capital base for survival and growth of the smelter, which remained and prospered under the Canadian Pacific umbrella for almost ninety years. It was registered as the Consolidated Mining and Smelting Company of Canada Limited in 1906; in 1966, this name wasshortened to Cominco Ltd.The Rossland mines continued to supply copper ore for the smelter until the late 1920s, but lead-silver ore also became available from the contemporary mining boom in the Slocan area, about 80 km away. In 1901, the Trail smelter diversified into lead; and when the CM&S Co. acquired the St. Eugene Mine at Moyie and the Sullivan Mine at Kimberley, the smelter was guaranteed a firm supply of lead ore. The company also purchased the West Kootenay Power and Light Company, which even before the turn of the century had constructed the first of four hydroelectric generating plants on the Kootenay River near Trail. This acquisition assured the CM&S smelter and its local mines of a stable power supply and the opportunity to diversify into power intensive technology."

Jan 1, 1988

By C. A. Sutherland

"Smelting of copper-gold ore from nearby Rossland mines started at Trail in the 1890s. As ore from the Rossland mines became exhausted, lead smelting offhand-sorted galena orefrom other British Columbia mines was initiated. With the development of flotation technology for the separation of lead, zinc, and iron sulphides in the first two decades of this century, the large Sullivan orebody at Kimberley, British Columbia, became the foundation for the growth of a major zinc and lead smelter at Trail. Lead smelting began in 1901, electrolytic zinc in 1916, and by 1984, the Trail metallurgical complex had produced 10 million tons of each metal. Its present capacity is 270000 tonnes per year of zinc and 110 000 tonnes/year of lead.This paper reviews the history of technological changes in the Trail production plants, emphasizing the zinc plant modernization program started in the 1970s, and also the planned introduction of the QSL oxygen lead smelting process in the late 1980s. Lead modernization will increase production capacity to a maximum of 160000 tonnes per year.IntroductionCopper-gold ore was discovered at Rossland, British Columbia, in the year 1890, starting a mining industry that was to last over three decade s. Selected ore was at first transported at high cost to distant U.S. smelters, so there naturally followed a decision to construct a small copper smelter to process the local ore to matte. It was built in 1896 at the mouth of Trail Creek on the Columbia River, about 10 km from Rossland. This little smelter was to develop and diversify in the next 90 years into the world's largest lead-zinc produce.The mining boom that occurred in the northwestern United States and southeastern British Columbia in the period of 1890 to 1910 saw the brief operation of many small local smelters. The only one to survive was the smelter at Trail. The circumstances that permitted its continued life and subsequent growth, form a fascinating history of business deals, litigation, and steady technical progress.Early investment in local railway transportation and options by F.A. Heinze, the smelter' s founder, attracted the attention of the Canadian Pacific Railway Company, which purchased Heinze' s assets in 1898. This provided the capital base for survival and growth of the smelter, which remained and prospered under the Canadian Pacific umbrella for almost ninety years. It was registered as the Consolidated Mining and Smelting Company of Canada Limited in 1906; in 1966, this name was shortened to Cominco Ltd."

Jan 1, 1988

By A. C. Elliott, A. J. Lafreniere

THE Hamilton Works of The Steel Company of Canada is a fully integrated steel plant with an annual capacity of three million tons. Located on the south shore of -Hamilton bay, it is in the centre of Hamilton's industrial belt. The heavy concentration of industrial activities found in this area, accompanied metallurgical well-known sources of pollution which are normal to urban areas is creating a pollution problem which concerns both industry and the general public. The Steel Company of Canada has recognized this problem and, accordingly, has adopted the policy of integrating suitable pollution control devices into its new installations. Much effort is also being expended to control the emissions of air contaminants from the existing equipment. At the Hamilton Works, there are two main sources of metallurgical dust emissions to the atmosphere -the Open Hearth furnaces and the Sinter Plant. Of these two, the Open Hearth furnaces are, undoubtedly, the largest single source of

Jan 1, 1962

By C. G. Harris, R. Sluyter

The purpose of an undercut is to undermine a block of ore which will then proceed to cave into draw holes just below the undercut. Undercut-ting is the final and most vital phase in the development of an ore block. Since its purpose is to undermine and induce caving into a block of ore, great care must be exercised to avoid premature caving by removing only enough rock to permit undercut development to proceed. Several undercutting methods, used over a twenty-year period, are re-viewed and their suitability is com-pared with ideal requirements.

Jan 1, 1960

By J-L. Tang

A new rhcoforming processing of Al alloys with component shaping systems apart from slurry preparation systems is experimentally exploited, using the reversible multilevel-speed electromagnetic stirrer, the slurry transfer tool and its coating, the thin plate sample with five steps and rheocasting mould, all of which are independently developed. The results show that semi-solid A356 alloy slurry with shape factor of about 0.85 and particle size of 70~80 µm (under air-cooling condition) could be prepared in 20~25 s, fully meeting the production rate of high pressure die casting. The slurry could be smoothly transferred from the slurry preparation equipment to the rheocasting shot chamber while the slurry temperature of slurry decreases by no more than 3 . The tensile strength and elongation of the semi-solid rheocasting samples could be respectively increased by 11.6~18.2 % and 42.5~50 % compared with the traditional liquid die casting ones, and the rheoforming processing has close affinity with the traditional hot working processes.

Jan 1, 2007

By J. Lobel, M. Bourassa, J. A. Kozinski, B. Peng

Non-isothermal kinetics studies of the reduction phenomenon of electric arc furnace (EAF) dust generated in stainless steelmaking have been carried out. The dust was mixed with carbon as a reducing agent and dolomite as a binder to form pellets. A Thermo-Gravimetric Analyzer (TGA) was used to determine the weight loss of pellets heated at an average rate of 40 K/min. up to a temperature of 1500°C. The degree of metal reduction was calculated by considering the pellet weight loss, and evaporation of moisture, dust, zinc and lead at high temperature. The reduction process was divided into three different steps. The first covers the 300°C to 760°C temperature range (from 7 to 18 min.), the second step ranges between 760°C and 980°C (18 to 24 min.), and the third covers temperatures above 980°C. Each step is characterized by different chemical reactions. Non-isothermal reduction kinetics equations were set up to describe each step. The kinetics parameters such as apparent activation energies and frequency factors were established. It was found that the first step was chemically controlled, while the second step was diffusion-controlled. Reduction behaviour in the third step was strongly dependent on the initial carbon content in the pellet. Chromium oxide (CrO) could only be reduced in this last step. High temperatures and higher initial carbon content favoured the reduction of CrO.

Jan 1, 2001

By R. Blazej

Machinery Systems Division (MSD) in the Institute of Mining Engineering at Wroclaw University of Technology specializes in belt conveying systems analyzing, calculating and design. Within the division operates the certified Laboratory of Belt Transportation (LTT) and Laboratory of Rollers. Since few years, a group of several people have begun work on developing a comprehensive system for the automatic evaluation of condition of conveyor belts working in the mines. Group uses both magnetic devices developed by specialized companies servicing belts and its own machine vision system developed for assessment of belts covers and edges during belt movement (up to 7 m / s) on the specially designed for this purpose the test conveyor. Recently they have got the research grant funded by the National Centre for Research and Development (NCBiR) for development of the system for automatic diagnosing of conveyor belts? condition and aiding of rational belt management. On the basis of previously created diagnostic tool called ABCDE (Automatic Belt Condition Diagnostic Equipment) the five modules: vision-A magnetic-B, preventive-C, forecasting?D, and determining safety factor-E will be developed. They will automatically interpret data about conveyor belts? condition to indicate the extent and timing of repairs, to prevent failures and to select the optimum moments for their replacements. The system will use results of ongoing research & development and planned research concerning modeling of belt wear using evolutionary genetic algorithms. The reached stage of research can not yet allow to start the implementation work by potential users. It is therefore necessary to pursuit research in real scale, the development of new modules (C-E) and intensive testing of the system in working condition with system calibration to optimize the economic effects.

Aug 1, 2013

By C. O. Swanson

"OUR INTEREST in estimates of world reserves of lead and zinc is focussed mainly on the information they give about the sufficiency of metal supplies for the future. However, we soon realize that the estimates can be interpreted in several different ways. Accordingly, it is necessary to have some under-standing of the elements represented by a compilation of world re-serves, and we will start by examining the accuracy of the estimates and what they attempt to measure.Variations in Estimates of the ReservesIf we study the estimates of world reserves that have been published in recent years, we note immenediately that they vary over a considerable range. For example, an article by Shea in 1947 gave world reserves as about 36 million tons of lead and 60 million tons of zinc. Shea did not in elude the United States but I have added to his totals the estimates made by the Bureau of Mines for that country in arriving at the foregoing figures. For approximately the same date, the American Zinc Institute and the Lead Industries Association reported world reserves as about 50 million tons of lead and 77 million tons of zinc. A comparison of the two sets of figures shows a mean variation of 30 per cent. For individual countries the difference between estimates can be even larger. A few years ago the estimate of Canada's reserves made by the United States Bureau of Mines was 7.4 million tons of lead and 14.0 million tons of zinc, while the Gordon Commission reported 1 O. 7 million tons of lead and 26.0 mil-lion tons of zinc. In this case the mean variation was 55 per cent."

Jan 1, 1960

Sherwood?s Minto Project ? High grade copper copper-gold deposit ? Yukon Territory, Canada ? Development underway ? Permitted ? Production by mid mid-2007 ? 40 40-50m lbs Cu plus Au/Ag by by-products ? Parallel exploration program underway ?Discover more high grade resources ?But what kind of deposit is it?

May 1, 2006

By W. Curlook, V. G. Papangelakis, M. Baghalha

A pressure acid leaching process has been developed for the extraction of metal values, nickel, copper, cobalt and zinc, from base metal smelter slags. The basic concept contemplates cooling the smelter slags through solidification sufficiently slowly to induce a good measure of crystallization; and subsequently, after fine grinding, to pressure leach such slags at around 250°C while applying oxygen overpressure, utilizing smelter byproduct sulphuric acid. High levels of extraction of the slags' metal values are thereby achieved. It has been shown that if the same slags are quenched thereby producing an amorphous structure, the resulting metal extractions are very low. The process is applicable to smelting furnace throwaway/discard/dump slags, as well as to in-process converter slags. By extracting the bulk of the residual base metal values in the throwaway/discard/dump slags, the resulting leached residues are rendered virtually benign vis-à-vis the external environment.

Jan 1, 2004

By W. L. Murphy

The Star Lake property, located 115 km northeast of La Ronge, Saskatchewan is underlain by metamorphosed andesitic tuffs and flows which have been intruded by the dioritic to granitic Star Lake Pluton. Gold mineralization on the Star Lake property was first discovered at Ru h Lake by E. Beveridge in 1959 and by M. and E. Hird in 1961. In 1960 E. Partridge discovered Kahn 18 and Kahn 28. In 1982 the SMDC-Starrex joint venture completed geophysical and geochemical urveys including magnetics, VLF, IP/Resistivity, vegetation, bulk till and oil sampling, followed by drill testing of pecific targets. To date the most ignificant depo it is the 21 Zone which contain drill indicated reserves of 230,000 tons grading 0.5 oz/ton Au . The 21 Zone con ists of quartz with 5-10% (locally > 30%) drusy pyrite, minor chalcopyrite and trace amounts of scheelite, chalcocite and arsenopyrite. The 21 Zone is enclosed by a 25-50 m wide band of mylonitized monzonite. The mylonite occurs in the central portion of a 300 m wide northeasterly trending zone of brittle deformation .

Jan 1, 1986

By Allan F. Lawrence

"I AM SURE you do not expect from me any learned dissertation on the problems and opportunities of the mining industry. Y our program committee must have recognized my limitations when issuing the invitation to speak to you, because they very thoughtfully left the subject wide open.With the leeway thus granted, I hope that you will bear with me for a few minutes while I try to clarify the impressions of the mining industry that I have gained in the very short time I have held the Mines portfolio and some of the parts that government bas or should have in furthering its development.As I see it, it is the duty of the Mines Department, as an arm of the provincial government, to balance the proprietary rights of all the people against the interests to whom the privilege of developing our resources are, in a s e n s e, leased. To strike a fair balance is not always easy, nor is it possible always to satisfy both sides. Still, under the free enterprise democratie form of government to which I think we al! subscribe, no better way of handling the problem has yet been discovered."

Jan 1, 1968

By S. Banisi, A. Haji-Zadeh, A. R. Hasankhoei, M. Maleki-Moghaddam

At the concentration plant of the Gol-E-Gohar Iron Ore Company (Iran) three 9m × 2.05m AG (Autogenous) mills (fixed speed) are used in parallel in a dry operation. The test works conducted in a scale down mill with a diameter of 1m indicated that conventionally used "deflector" type liners did not provide efficient environment for grinding. In this research, to improve the grinding efficiency, a new design using low profile end liners incorporating radial ribs of proper height was investigated. In order to determine an appropriate liner design at different operating conditions, a 100cm×10.8cm model mill was used for experimentation. The special design of model mill made it possible to increase the radial ribs height in steps of 6mm up to 18.5mm. The transparent end of the mill enabled accurate trajectory determination by image analysis. The results indicated that the new lower height profile deflectors and 15.5mm-height (14.5cm in industrial scale) radial ribs improved the mill performance while avoiding excessive pressure drop across the mill and wear on the liner. The image analysis showed that the use of new liners increased the distribution of coarse particles across the mill cross section from 28% to 35%. A new liner design was proposed by decreasing the number of liners in each slice from 5 to 4 pieces. The thickness of the inner head liners reduced from 45cm to 30cm and the outer deflector liners replaced by radial ribs. The distance between the feed and discharge inner head liners increased from the original 115cm to 145cm which increased the effective length of the mill by 26%. The new design reduced the weight and volume of end liners by 9% and 23%, respectively. It was predicted that the new liners design increases the mill throughput by 10% and reduces the metal consumption by 20%.

Jan 1, 2016

By S. Banisi, E. Arghavani, A. Akbari, Gh. A. Parsapour, S. Darvish Tafvizi

The new copper processing plant of the Sarcheshmeh copper complex consists of two parallel circuits. After a primary crushing, the ore is sent to a SAG mill and the product is further ground in a ball mill. The overflow of the hydrocyclones is fed to a flotation circuit which contains 8 rougher tank cells (RCS130), 3 cleaner cells (RCS50), 5 scavenger cells (RCS50) and a 4 x 12 m flotation column as recleaner. The circuit was initially designed to process a feed containing 0.8% Cu, but because of the ore type change, the feed grade decreased to 0.6% Cu. This resulted in a reduction of final concentrate grade and recovery from 28 and 85.5% to 24 and 84.4%, respectively. Based on the original design, the copper and silica recovery in the cleaner cells should be 69 and 55%, respectively, but these values increased to 85 and 75% because of a higher retention time. The rather high silica recovery (i.e., 75%) was found to be the main source of the lower final concentrate grade. In order to reduce the retention time of particles in the cleaner cell from 13.7 to 6.9 min, the rougher concentrates of two parallel circuits were fed to only one cleaner-scavenger and regrind circuit. This modification increased the cleaner and final concentrate grade from 15.1 and 24.5% to 17 and 26%, respectively. To prevent a possible reduction in the copper recovery, the froth depth in the scavenger cells was reduced. The overall outcome of the circuit modification was evaluated to be a 10% reduction in the energy consumption without any loss in the overall copper recovery.

Jan 1, 2016

By J. Tuzo Wilson

Abstract A division of part of the Canadian Shield into provinces believed to represent former mountain belts is attempted, special emphasis- being laid upon radioactive age determinations, the relation of Archaean to Proterozoic rocks, and the structure of the Grenville province. Original data on the distribution of radioactivity within several batholiths and their connection with ore deposits are' presented. The possible growth of continents and a theory which explains the shape and distribution of the world's younger mountain and island areas are discussed and applied to the Canadian Shield in an attempt to explain how the growth and present structure came about. The relation of the major mining camps of northeastern Ontario to fault zones is discussed in the light of this theory. Introduction The valuable symposium issued by this Institute to celebrate its jubilees emphasizes the important role of major faults in determining the location of many ore deposits in the Canadian Shield. Many of these faults are known to extend for long distances. It is therefore widely appreciated that it would be of great value if the pattern, ages, and causes of these faults were better understood. This would be particularly useful if the relations of the major fault systems to petrological and metallogenic provinces and to former mountain belts could be established. Each year the volume of available data, and hence the chance of reaching a fuller solution of this problem, increases. This article is a review of the present situation. It is accordingly based almost wholly upon the work and ideas of others, which are gratefully acknowledged. Naturally, responsibility for the selection and marshalling of the data is the writer's.

Jan 1, 1949

By T. S. Heah, S. T. Bishop

"The Lorraine property is located in the northern Intermontane Belt, north-central British Columbia. The property is underlain by intrusive rocks of the Duckling Creek Syenite Complex, an Early Jurassic, alkaline phase of the Late Triassic-Early Cretaceous Hogem Batholith. Two significant zones of copper-gold mineralization have been explored to date; the Main zone (historical Upper and Lower deposits) and the recently discovered Extension zone. A combined geological resource was estimated in 1975 for the Main zone deposits at 10 million tonnes averaging 0.7% Cu, and from 0.1 g/t Au to 0.34 g/t Au. The Extension zone, still at an exploration stage, is estimated to be considerably smaller than the Main zone.Copper-gold mineralization at Lorraine Mountain exhibits characteristics suggestive of both magmatic and hydrothermal origins, and may be related to orthomagmatic-hydrothermal fluid flow contemporaneous with magmatism and development of migmatitic fabrics. A depth greater than the depth of formation of classical porphyries may explain many of the variations displayed by mineralization at Lorraine. These characteristics distinguish Lorraine from other members of the alkalic suite of porphyry Cu-Au deposits in the Canadian Cordillera.IntroductionThe Lorraine prospect is located in the Omineca Mountains, at the headwaters of Duckling Creek, 56 km northwest of Germansen Landing (Fig. 1). The property is centred at latitude 55°55'N, longitude l25°26'W on NTS mapsheet 93N/14W. The area is typified by mountains of moderate relief, with elevations ranging from 1150 m in the valleys to peaks of 2000 m. Valleys are U-shaped and blanketed by glacial till which give way to steep, talus covered slopes and sharp ridges. Outcrop is generally limited to elevations above 1600 m (Fig. 2)."

Jan 1, 1995