Search Documents

Authorisation No.66 (to Prospect) was allocated to R.W. Miller & Co. Pty. Ltd. on 1st November, 1976. Exploration has brought coal reserves to measured status in the Jerry's Plains sub-group which are about 550m. thick. The immediately lower Vane Sub-group, about 200m. thick, includes about 20 seams. The total measured and indicated reserves of the two sub-groups based on the criteria adopted by the company amount to 1362 million tonnes in situ. This very large resource is subject to very many mining constraints both physical and economic which limit the saleable reserves under present conditions to about 120 million tonnes. The results of the calculation of reserves after exploration is complete in a deep multiple seam situation is dependent upon the criteria used to include or exclude seams in the reserves. These criteria are state- ments of the miner's expectations of the market, mining and coal preparation technology, local and national politics and the law as it may be applied in the future.

Jan 1, 1979

Rock bolting provides a supplement or alternative to conventional timber and steel supports. The tensile strength of the bolts lies within a range established by manufacturing quality control. Rock bolt testing determines the ability of the rock, anchor and individual bolt as an assembly to accept load. The.test is performed to the yield strength of the bolt or anchor and deflection is observed. The anchorage index, inches deflection per 1000 lb load increment, is a measure of anchorage quality. This allows comparison with anchorages under ideal conditions. It also permits comparative assessment of roof bolt anchors in a particular environment.

Jan 1, 1971

By Kidman B. E

The Fitzpatrick area is the deepest section of the North Mine, with the orebody located between 1450 and 1800 m below the surface and some 600 m NE of the main No. 3 Shaft orebody and separated from it by the intensely sheared Globe Vauxhall Shear Zone. Development towards the Fitzpatrick area commenced in 1977 after earlier initial exploration drive development. However, it was not until 1982 that mining in the Fitzpatrick area actually began with the silling out of No. 36 level at a depth of some 1600 in. Since that time mechanised cut and fill mining from an incline ramp system with connecting stope accesses has progressed some 25 m above No. 36 level. Initial sill development on No. 37 level at 1660 m depth also commenced in July 1987 to further develop the Fitzpatrick area.

Jan 1, 1988

By Li T

Mining of the southern 1900 copper Orebody presented a challenge due to the complex geology, geometry and simultaneous extraction of the nearby lead/zinc/silver orebody. An integrated and co-operative approach was adopted, involving geology, geomechanics, mine planning and production personnel. Successful extraction of the first 1900 Orebody stope, T496, together with the extraction of the first two lead/zinc/silver panel stopes in the immediate hangingwall of the 1900 Orebody stope was achieved as a result of this approach.

Jan 1, 1995

Electrochemical investigations of the flotation of sulphide minerals are re- viewed. Flotation with thiol collectors is interpreted in terms of a "mixed poten- tial" model in which the process leading to hydrophobicity is the anodic oxidation of the collector at the mineral surface and this is driven by the cathodic reduc- tion of oxygen. Electrochemical studies have identified the products of anodic oxidation as chemisorbed collector, metal collector compounds, and dithiolates; the products formed in each situation depend on the collector used, the mineral under study, and the pretreatment of the mineral surface. Investigations on galena, pyrite, and chalcocite are discussed. Electrochemical and x-ray photoelectron spectroscopic studies have been used to determine the products of surface oxi- dation of sulphide minerals in order to elucidate the mechanism of collectorless flotation. The mixed potential mechanism allows consideration to be made of the ways in which flotation of sulphides with thiols can be inhibited. Examples of depressant action are presented. The relevance of electrochemical investi- gations to practical flotation is Discussed.

Jan 1, 1984

In eastern China, most of the copper skarn deposits occur in folded troughs which are controlled by the EW-trending faulted fold systems (the Pal-Asian geotectonic domain), and the NNE-trending rift or fault zones (the Marginal-Pacific geotectonic domain), particularly the later. From the north to the south, there are four troughs hosting the main copper skarn deposits in eastern China: the Yanliao Trough, the Yangzi River Trough, The Qiantang-Yuanshui Trough and the Zichen Trough. There are more than 30 copper skarn deposits in eastern China, and ore reserves of each deposit are between 30 to 100 Mt with average grades over 1 % Cu.

Jan 1, 1995

The Antarctic Peninsula consists of accretion complex sedimentary and volcanic rocks, talc-alkaline magmatic are rocks, marginal basin sediments and extension-related alkali basalts, dominantly of Mesozoic to Cenozoic age. Metallic minerals have been recorded at "250 localities but two thirds of these are innocuous occurrences of Fe+Cu accessory minerals. The remaining -70 localities are related to hydrothermal mineralization processes. Metallogenetic associations identified are: vein and breccia-hosted Fe+Cu+Zn+Pb+Mo or Fe+Cu+Mo+Mn, shear-hosted Fe+Cu, volcanogenic Fe+Cu and pegmatite-hosted Fe+Cu+Mo+Mn. Anomalous Au, Ag, As, W and Sb also occur but are not of economic interest. Metallogenic zoning is unproven and genetic models are uncertain, possibly involving volcanogenic, epithermal to hypothermal vein and porphyry-type systems. Substantial field and laboratory studies are required to understand distribution and Genesis.

Jan 1, 1987

Roller seed screens were installed at The Broken Hill Proprietary Company Limited (B.H.P.) Whyalla pellet plant to replace vibrating screens on the green ball circuits. The installation of roller screens was justified by improving the sizing of the green balls. This improved sizing increased the yield of fired pellets produced from green balls thus decreasing the fuel consumption. The fired pellet sizing was improved also. This paper discusses the configuration of the roller screens installed at Whyalla, quality of green balls produced, advantages of roller screens compared with vibrating screens and future development of roller Screens.

Jan 1, 1984

Efforts to stabilize international markets in commodities have gradually intensified during the course of this century in keeping with the grow- ing complexity and interdependence of the world economy and the increasing involvement of government in economic activity. Successive Australian Governments have con- sistently supported the concept of commodity agreements and arrangements in an effort to lessen short term fluctuations in price and to moderate the boom/bust conditions which tend to charac- terize production and trade in many commodities. The objective is to stabilize price at a level which equates supply and demand over the life of the arrangement. Such action involves a degree of market inter- vention and government involvement in the inter- national trade in the commodity concerned; the acceptability and desire to foster such arrange- ments varies from country to country depending upon attitudes to market intervention and man- agement. However attitudes, even among those opposing commodity agreements, have under- gone a major reversal in this century. Before the first world war, such intervention as existed almost entirely involved the physical producers. There was almost no government involvement and at that level most regarded commodity agree- ments as neither desirable nor practical. However government regulation of such activities as pro- duction and marketing of food during World War I, coupled with post-war shortages, followed by overproduction and the crash in prices during the Great Depression, stimulated producer gov- ernment interest in commodity market regulation. Consumer governments took a little longer and with a few exceptions, it was not until the post World War II period, that the fear of shortages of basic commodities brought some consumer countries to accept the concept.

Jan 1, 1978

By Bhattacharyya A. K>

The Pemali Open Pit Mine is situated in a small island called Bangka in Indonesia. It produces approximately 165,000 m3/year of tin ore with an average grade of 3.67 kg/m' of tin from a primary deposit. The deposit occurs at the rim of a granitoid intrusion within sedimentary beds. The rock formations, all extremely weathered, and the overlying alluvium, are exposed to a rainfall exceeding 3m/year. Serious slope stability problems are experienced at the mine, despite using overall pit slopes of 20¦-29¦, the latter resulting in a stripping ratio of 4:1. This paper outlines a computer based back analysis of a major slope failure involving some 250,000 m' of material which occurred on the west wall of the pit in February, 1984. The findings from the analysis, together with other information, are used to examine the stability of the east wall of the pit, where tension cracks developed later. The results indicate that the large influx of water was the most significant cause of such slope stability problems and a more intensified water management programme would be beneficial.

Jan 1, 1989

By Baafi E. Y

In this paper, impact of expert systems development is examined from the coal mining point of view. Some introductory concepts about expert systems are explained with a view to identifying possible beneficial applications of expert systems in coal Mining.

Jan 1, 1988

It is people, not organisations, that make countries great, so it seems appropriate in this Centenary year of The Australasian Institute of Mining and Metallurgy to highlight some of the mining personalities who have contributed to the greatest and most important of Australia's export industries, the Resource Industry.

Jan 1, 1993

A Modelling Approach Using a Back-Calculated Induction Time to Predict Recoveries in Flotation

Sep 13, 2010

By J Zhiming, X Qian

All high stopes and pillars in Anqing Copper Mine were extracted by use of large-diameter longhole mining method. The height of stopes was 120 m. The forced mining was the leading concept that the safe and efficient operation was carried out in this mine, while the mining production was faced with the major technical problems on the stability of both primary ore pillars produced in the first-step stoping of stopes and the cemented fillbody on two sides of stope in the second-step stopping of pillars. Starting with mining technology, the authors emphatically describe the test results obtained in Anqing Copper Mine and make an approach to the deployment prospects and development trend of large-diameter longhole mining technology in China underground metal mines.

Jan 1, 2000

An algorithm is described which leads directly to a unique set of coal washing parameters which, in two or more parallel streams, will give maximum yield of product at a given ash. This occurs when all parallel streams are washed to the same incremental ash. This strategy is shown to offer a considerable increase in yield compared to the simpler strategy of washing each stream to the same sumulative ash.

Jan 1, 1987

By M Brooks, M Nelson

A fundamental study was carried out on super pit sulphidic gold ore to establish the most influential flotation characteristics which were subsequently used in the development of an optimum flowsheet to achieve best economical recovery of gold. In developing the flowsheet, consideration was given to existing operational constraints in the treatment of the Super Pit ore. The fundamental study also included an innovative diagnostic investigation to establish the location and value of gold in the major mineral assembly of the super pit ore from a metallurgical rather than a mineralogical perspective. This study mapped a metallurgical fingerprint of the major types of super pit ore in relation to the location and association of gold.

Jan 1, 2000

It was once considered sufficient to revegetate old mine sites using grass or trees. At the commencement of the Stawell JV (SJV) operation in 1981, management determined that pre-existing vegetation would be replaced. This policy was somewhat 'ahead of its time'. The cost of rehabilitation at SJV averages $8000 per hectare. Rehabilitation of this calibre requires a practical understanding of local ecosystems.

Jan 1, 1992

By J Lim, M Powell, P J. Scales

The current philosophy employed in the design of mineral processing plants effectively involves bolting together segmented unit operations both chosen and optimised from a product-centric perspective. In this context, integration of water saving technologies at an overall plant level becomes difficult and often only local water efficiency improvements are feasible. In general only limited benefit can be obtained from such add-on solutions. It is therefore proposed that to obtain significant savings in water consumption and reductions in the volume of discharged contaminated water in the mining process, the entire process along the mining and mineral processing chain should be addressed This paper explores aspects of the processes that may be modified to provide an integrated and combined step change saving in water consumption. It is also apparent from this study that taking a more holistic view of the process can provide significant benefits in energy savings and total cost of production, providing the potential of a substantial win-win outcome.

Jan 1, 2009

By Croggon R

Passing a direct current through a jointed fine grained soft rock mass auses the movement of water by the process of electric-osmosis. There are other processes such as electrolysis which transport ions that interact with associated ions and can, in turn, be oxidised. This results in the dissolution products being transported towards the cathode electrode. In the cathode region the ferrous hydroxide is oxidised to ferric hydroxide %%ith consequent precipitation. The cracks and joints are current pathways, along which the ferric hydroxide is deposited. This deposition reinforces the joints and increases the shear strength. By adding calcium chloride to the anode, the rate of corrosion is increased with the concomitant increase of deposited ferric hydroxide along the joints. This, in turn, significantly increases the joint shear strength. The process is pervasive in that the current via the water paths travels through the crack and joint systems The result is that not only specific joints are reinforced but the cracks and mtciconnected voids are also reinforced.

Jan 1, 1997

"DEEPHOLE " or "Longhole" drilling is the name given to the drilling of prospecting holes with the pneumatic hammer drill. The drilling bit is of the same form, and is prepared in the same way as ordinary rock drill steel, and is extended to the bottom of the hole by sectional hollow rods, through which water is forced.The cuttings from the hole provide a sample of the ground drilled.Deephole drilling was developed at an American mine where the cost of diamond drilling, owing to loss of diamonds, was excessive, and proved very successful, holes being drilled as deep as 220 ft., in limestone, at a cost of one dollar per foot. The use of the method in other mines, and in a variety of rocks, has since been described in the technical literature. From the published descriptions the following data are drawn:

Jan 1, 1930