Search Documents

By Forssberg E

This paper presents the experimental results on the effects of slurry Theology on ultra-fine grinding by a stirred ball mill. The amount of dispersant, slurry density and the particle size were selected as the parameters. The viscosity of dolomite-water slurry was measured by rotational viscometers. It was found that by adding enough dispersant, the effect of particle size from 1 to 10 pm on the slurry theology could be eliminated, but a strong effect of slurry density (tested for a range of 65 to 75 wt per cent) remained. The use of dispersant transformed the slurry from Bingham plastic flow to dilatant flow, which reduced the yield stress to zero, but increased the viscosity at higher shear rates. During the milling process, the viscosity was stable. The yield stress, however, increased suddenly from zero after a certain milling time. The mill operation stopped at the point where the yield stress increased due to poor slurry fluidity. The milling efficiency was found to be higher at a lower amount of dispersant addition or a lower slurry density within the experimental limits.

Jan 1, 1993

Dr. Willett. I will start by answering one or two general points which have been posed. The first point is a question of liability of a seam to spontaneous combustion. Some seams are very liable to spontaneous combustion. Some seams are not liable at all except in most abnormal circumstances, and some seams have a liability somewhere between these two extremes. Dr. J. S. Haldane made the comment some 50 years or so ago that if you try hard enough you can make any coal seam in the world fire spontaneously. Many heatings have in fact occurred because the coal has been allowed to be ground up into a fine state and there has been air leakage through it for many years. This has resulted in spontaneous combustion which would not have occurred in some seams unless conditions had been very abnormal indeed. One comment I heard while listening to the discussions of one team was the importance of encouraging morale and the team seemed to go to the extent of suggesting that this was more important than the actual technical action taken. Though I agree that everything possible should be done to encourage morale, it must be in conjunction with the correct technical method of dealing with the Emergency.

Jan 1, 1973

The subject of the present paper will be combustion of fuel and as the combustion of fuel requires a certain amouut of air to effect combustion the question might be asked what is air?Air is composed, we will say, principally of two gases, oxygen and, nitrogen, but our business is with the former gas, and its leading feature as a supporter' of combustion. In point of fact no fire will burn without its presence, nor can animal life be sustained when this gas ls absent, because it is the life-sustaining element. For example, if we take a piece of charcoal, which is pure carbon, and burn it in the open air combustion takes place in the union of the carbon of the charcoal with the oxygen of the air, forming the compound known as carbonic acid (0.0.)The rust we see on iron and other metals is a kind of slow combustion, which is termed oxydation. When oxygen unites with any other element heat is given off in the process, and it may be here stated that the most intense heat is produced, by burning the two gases-oxygen and hydrogen in precisely the same proportions as that forming water.

The following is an outline of the main metallurgical process developments which have occurred at Port Pirie during more than 100 years of smelting. Emphasis is placed on those process developments which evolved from research and development at Port Pirie, rather than those based upon purchased or established technology and straightforward plant engineering. Most processes involved have undergone major change and improvement through the efforts of Port Pirie staff. A culture of metallurgical research and development evolved strongly during the years when G K Williams made such a great impact, and continued for half a century. This culture involved strong links with external research bodies, particularly universities. A near complete bibliography of these developments is provided, together with a listing of patents. Research and development by The Broken Hill Associated Smelters Pty Ltd commenced in 1918 at South Melbourne, and after transfer to Port Pirie in 1921, continued there until 1989. Three periods of highly successful innovation resulted ù that of G K Williams into the 1930s, the post-war period until about 1962 and the period with developments led by Denby H Ward from about 1970 to 1985.

Jan 1, 2000

By Cutafani M, Lama R

An approach to combatting abnormal roof control conditions in underground coal mines is outlined. Support techniques available are discussed along with the methods available to be adopted in different situations. Properties of materials available presently are tabulated together with the conditions of their Application.

Jan 1, 1988

Both innovation and excellence are desirable attributes of education, as they are also markers in the progression of the human race, but how attainable are they? The interaction of minerals and humanity provides a special insight into the development of both criteria, from the discovery that chert cuts, through the Bronze Age and the first use of metal alloys for implements, to using coal, oil and uranium as sources of fuel. However, there have been many hiccups along the way, where excellence in one respect has meant disaster in another. Examples are in the exploitation of asbestos, and in traditionally poor work practices in mining, both contributing to the widespread public belief that minerals and mining are ecologically undesirable. Yet is this perception based on the unrealistic expectation of innovation and excellence being simultaneous qualities of any given process? Common sense born of experience indicates that the journey from one, to the other, is usually a long and often tedious process, with much trial and error before excellence is attained. In our time, the partnership between academia and industry is the usual pathway to achieve it. Even so, we should take care that innovation does not become overwhelmed by the pursuit of excellence: as history clearly demonstrates, humanity depends upon both.

Jan 1, 2004

The South Ghorveh Batholith (SGB) and the Almoughlagh Batholith (AB) intruded the volcanosedimentary sequence of Songhor Series (Triassic-Jurassic), during the Oligo-Miocene orogenic phase. The granitoids of the AB belong chiefly to the quartz-syenite and syenogranite clans while those constituting the SGB can be generally characterised as quartz monzonite varying towards quartz monzodiorite, and diorite. Granitoids constituting both the batholiths are low in free quartz, and possess characteristics of the æmagnetite seriesÆ, mostly of I-type, metaluminous to marginally peraluminous and calk-alkaline type. Adjacent to them are located the magnetite skarn deposits of Baba Ali and Gelali. In the light of petrography, geochemistry, mineralogy and field geology investigations they could be classified as Fe-skarn and mainly bear characteristics of calcic skarn deposits.

Jan 1, 2005

Early efforts to control the dust necessarily produced during dry crushing operations, took the form of venturis at loading chutes and other places where dust was most evident. These venturis discharged to the atmosphere and for obvious reasons were not very satisfactory.Attempts to collect the dust drawn off by the venturis, using dry cyclones, were not successful, the cyclones catching only the coarser particles. Further, no satisfactory method of continuously discharging the dust catchment was evolved. Water sprays were also used, and will be referred to later.In 1940, a single discharge fan of 3,000-4,000 cu. ft. per minute capacity, was installed to draw the dust-laden air from the Symons crushers and ·screening sections with their attendant conveyors. Suction was through two 15 in. ducts which branched off into 10 off-takes situated over the conveyers at points of discharge from crushers and screens.A dry cyclone was installed in front of the fan, which exhausted into a bag-house.The cyclone suffered from the defects of the smaller units mentioned earlier. When the collected dust reached a certain level in the cone, no more collection would take place until the cone was emptied. This objectionable feature was overcome by introducing a jet of water ahead of the cyclone. The water and dust collected overflowed a weir and were pumped to the mill.

Jan 1, 1948

The efficient development and exploitation of an orebody relies on an understanding of the mineral characteristics of the deposit. This information is valuable throughout the mining cycle - during exploration, assessment, testing, design, operation and rehabilitation. Problems can arise at each stage if there is an inadequate appreciation of the mineralogy involved and its effects on the treatment process. Modern image analysis systems now permit a more quantitative understanding of the mineralogy of an ore to be gathered. Where previously the metallurgist had to rely on qualitative information to guide technical decisions, it is now possible to give numerical estimates to the compositional and textural properties which govern the mineral concentration processes. Ore samples can be characterised according to modal abundances, mineral grain size parameters and mineral associations, all of which affect the liberation and concentration of the values. The paper will discuss the application of quantitative process mineralogy by considering a number of case studies. These include: ore characterisation to assist in exploration, assessment and mine planning; modal analysis of complex mineral suites to assist in the evaluation of ores, the deportment of values between products and the recovery or loss of these values; liberation analysis for ore testing, plant optimisation and performance monitoring; and characterisation of tailing to guide estimates of leachability, stability and rehabilitation options.

Jan 1, 1998

By M Zaluski, D Bless

An innovative, biological treatment process has been designed by MSE Technology Applications, Inc to treat and control acid mine drainage (AMD). A field-scale demonstration is being conducted under the Mine Waste Technology Program using water flowing from a historic mine in Montana. A successful demonstration of an in situ process will allow it to be employed at numerous other abandoned or remote mines, which discharge AMD, an acidic, metal-contaminated water. Conventional treatment methods are costly and are often impossible to use at remote locations. MSEÆs technology uses a biological system to clean up AMD. The In situ Passive Biological Treatment Process utilises nonpathogenic bacteria, which are able to neutralise acidic mine water and remove contained toxic metals. These bacteria live within a series of pile-type reactors inside the mine. The bacteria are fed inexpensive waste products. The resulting discharge is clean water flowing from the mine. This presentation will show that this technology offers a natural cleanup method for the nationÆs numerous abandoned mines. Work on this project was conducted under Interagency Agreement No DW899388-70-01-1 between the US Environmental Protection Agency and the US Department of Energy (DOE), and was performed at the Western Environmental Technology Office through the DOE National Environmental Technology Laboratory (DOE Contract No. DE-AC22-96EW96405).

Jan 1, 2003

THE following paper is a description of the plant and operations of the above company in their recovery and treatment of the quartz tailings deposited as final residues by the various mining companies. at Waihi, Karangahake, and Waitekauri into theOhinemuri River. During the past few years the silting of the Ohinemuri River has increased to such an extent as to cause considerable interest and discussion, and has lately been the subject of a most extensive inquiry by a Royal Commission, to consider the best means of dealing with what is generally spoken of as a public nuisance.Ever since the commencement of mining in this district, which was opened as a goldfield in 1875, the various mines operating have been discharging their tailings into this river, it having been proclaimed a sludge channel in 1895. Up to the year 1900 the quantity of quartz crushed was not large, probably not exceeding 500,000 tons; but since that date the annual tonnages discharged have increased enormously, and at the present time would total from 550,000 to 600,000 tons per year. Records show that up to the end of 1910 at least 5,000,000 tons have been crushed, for an actual yield of bullion considerably exceeding £10,000,000 in value, and all the valuable tailings from...

Jan 1, 1911

By R Hoeppel, D Harimon, A Fisher

This paper examines the importance of examining the relationship between biology and geochemistry when designing a biopile to treat alkaline soils impacted by petroleum hydrocarbons. At a site in Nevada a large, unlined pit was constructed in a loamy sand soil and filled at regular intervals with a mixture of jet fuel, lubricating oils and waste solvents which were set on fire by the local fire department for training purposes. During its period of operation numerous chemicals were also dumped into the pit for disposal purposes, including dichlorobenzene and various chloroethylenes. As a result of these activities a large groundwater contaminant plume was formed. As a part of the site remediation process a decision was made to perform a limited source removal and excavate the top three to four metres of contaminated soil from the burn pit and place it in an engineered biopile. The location of the training pit is in a heavily mineralised basin where the background sulphate level in groundwater exceeds 5000 ppm. Due to naturally occurring biodegradation of the petroleum hydrocarbons a large portion of the sulphate was converted to sulphide which deposited in the soils as marcasite in the anaerobic soils. The initial attempt at soil remediation was to use a forced air treatment scheme that had worked well in small scale laboratory testing. Unfortunately, when attempted in the field on a large scale, marcasite reacted with atmospheric oxygen resulting in internal biopile temperatures exceeding 90¦C resulting in the virtual sterilisation of the soils without remediation occurring. In order to solve this vexing problem Pintail Systems, Inc developed an anaerobic culture that allowed the pile to be operated under anaerobic conditions. Within three months the biopile successfully demonstrated on a large scale significant biodegradation of the refractory petroleum hydrocarbons.

Jan 1, 2004

By S Planeta

The use of explosives in underground mining has its drawbacks, particularly in the case of thin or narrow vein type deposits. Due to that, there is a need to develop more discriminative and safe rock-breaking technologies. Mechanical rock splitting seems to be one of the most promising avenues in this respect. This paper describes briefly principles and features of radial-axial splitters. It reviews a feasibility study done to evaluate a potential of this technology in selective mining. It was intended to compare productivity and cost of ædrill-splitÆ mining with conventional cut-and-fill method. Hypotheses and assumptions adopted, methodology used and the obtained results are presented and discussed. The study has confirmed an interesting potential of radial-axial splitters in mining thin and narrow vein deposits. In conclusion, it is stressed however, that it will take more R&D work to corroborate the results obtained. Some suggestions concerning future research in this field are also given.

Jan 1, 2003

By R G. Alford

Braeside Borefield, located 120 km southwest of Mackay, is owned by BHP Mitsui Coal Pty Ltd (BHP Mitsui). The borefield provides water to BHP MitsuiÆs South Walker Creek and Riverside Coal Mines and communities in the northern portion of the Bowen Basin. Braeside Borefield has also provided water for other users in the region, including the Peak Downs, Goonyella and Saraji Coal Mines owned by BHP Billiton Mitsubishi Alliance (BMA). Water is sourced from alluvial sediments at the confluence of Nebo and Denison Creeks, and transferred a distance of almost 100 km to Riverside Mine and other users. Since commissioning in 1983, monitoring and maintenance programs have been key elements in borefield management. The impact of pumping on groundwater resources is monitored at the borefield, upstream and downstream over a distance of about 50 km. Current annual pumping is of the order of 4000 ML, and in excess of 50 000 ML has been pumped since the commencement of borefield operations. Detailed reviews of borefield performance are conducted every two years. BHP Mitsui actively participates in community consultation on groundwater issues arising from operation of the borefield. Declining groundwater levels from prolonged drought conditions have increased community interest in management of the borefield. Rehabilitation of existing production bores and augmentation of the borefield is currently being investigated to more evenly distribute pumping rather than to increase overall capacity.

Jan 1, 2003

By B Leyland

The media in Australia is currently rife with articles and pronouncements on global warming as the most significant crisis of our time, which may æthreaten the future of civilisation as we know itÆ. This has been recently reinforced by release of Al GoreÆs film æAn Inconvenient TruthÆ, and one would be led to believe that the science of global warming is settled. And yet there is a strong body of literature disputing this apparent consensus which suggests that care should be exercised in introducing radical policies to solve a crisis which may not be real. Such policies would have a major impact on those in professions such as engineering (project approvals and design to minimise greenhouse gas emissions), accounting (carbon tax issues) and the law (corporate disputes on greenhouse gas issues are already in train in the USA). This paper addresses the hysteria apparent in the climate change debate by presenting factual evidence relating to climate change and the current phase of mild global warming. Some of the more extreme statements on future impacts are repudiated with published data, and alternatives to the purported role of fossil fuels in temperature change are offered. The potential impact of political decisions on professional activity is discussed, as are the implications of a possible future reversal of the scientific consensus, as has occurred in the past. The paper concludes with a call for the professions to exercise their Learned Society role to ensure that a rational and public debate is held on the broad issue of climate change.

Jan 1, 2007

The geochemistry of waste rock from mining operations is critical to the development of acidity-related environmental problems during mining operations, and following mine closure. Failure to recognise the potential for waste rock to produce acidic oxidation products may cause mobilisation of heavy metals into ground and surface waters, and create heavy metal levels in soils which are toxic to plants, causing the failure of revegetation programs. Although more usually associated with wet tropical environments, the potential exists for these problems to occur even in and regions such as the Eastern Goldfields region of Western Australia unless appropriate pre-planning is undertaken.Acidity-related mine waste problems can be extremely expensive to rectify, but can be avoided by waste rock characterisation, and pre-planning of waste rock deposition based on this information. Integration of knowledge of waste rock geochemistry with geotechnical engineering, and application to likely problems, is essential for the successful planning and implementation of cost-effective strategies to avoid problems occurring. Pre-planning to avoid problems is likely to be significantly less expensive in most cases than remedial actions to rectify problems after they have occurred, and in fact may involve no additional cost if it requires only rescheduling or redesign of existing or planned Activities.

Jan 1, 1993

In another paper the author described the electrolytic preparation of highly-purified lead. One of the most difficult parts, yet perhaps the most essential part, of that research was to ensure, firstly, that the purification process should be effective; secondly, that it should remain effective; thirdly, that the lead should not be contaminated during the tests that were done on it. All this necessitated periodic analyses of the lead.The purpose of this paper is to describe the work done by the author to check the accuracy of some known rapid methods for the estimation of impurities in highly-purified lead, with the intention of applying them to the control of the electrolytic process above-mentioned.METHODS ALREADY IN USEThe literature sets out accurate methods for the estimation of impurities in lead, but these methods are both lengthy and expensive. For example, the method described by Hemingway is used in the Port Pirie laboratory of the Broken Hill Associated Smelters Pty. Ltd., but it requires a sample as large as 1000 grm., and the time required to analyse a sample extends over days, and is too long to allow of quick control over a running process. This method was used by the Associated Smelters to obtain the analyses quoted in another paper by the author.

Jan 1, 1932

Nearly eighteen months ago Newmont Waihi Operations joined with the local district council and members of the Waihi community in the initiation and running of a community liaison forum.   This forum û the Waihi Community Consultative Committee (WCCC) û was set up with the objective of improving communication, providing a forum for discussion and ultimately working through a range of issues relating to the future of the town and district after the projected closure of Martha Mine in late-2006.   After 18 months of meetings where all represented groups have presented their views, the challenge now is to work together to investigate likely options, seek sources of funding, produce business proposals and plan for the future of Waihi in what we call the Golden Legacy Project.   This paper backgrounds the companyÆs experiences to date, the issues the group has addressed and its proposals for the future. Methods employed to set up an effective community liaison forum are considered, drawing on specific examples from the WCCC. The actions and structures required to ensure effective and ongoing community æbuy inÆ at all levels are also discussed.   This paper develops themes addressed in Taking it to the Streets presented in 2003.

Jan 1, 2004

The risks faced by organisations are part of a risk continuum. They can be evaluated in terms of hazard, uncertainty and opportunity as well as by the degree of influence they have on conformance, operating performance and strategic objectives. This paper discusses the application of risk management techniques for mitigating blasting hazards, reducing blasting output variability, and implementing blast improvement opportunities. Effective risk management practices can identify and evaluate risks across all levels of the continuum and can deliver realistic assessments of the likelihood and impact of risks on the companyÆs safety and business objectives. This paper does not attempt to present technical details about blasting, rather it aims to provide enough blasting context and examples so that the practical benefits of applying the risk management process to blasting can be fully appreciated. The topics discussed include: explosive management plan; statistical process control; quality blasting, rock-on-ground; Blast Management; Mine to Mill optimisation; and blasting information systems. The concept of a blasting risk management system employing a continuous improvement loop is also introduced. On reflection the insights presented should be extremely useful for observing and understanding which risk face has management focus at a mine site or for a blast site.

Jan 1, 2001

The flotation circuit handling Peko ore at Peko Mines N.L. was examined in July 1970 with a view to determining simple changes in circuitry or reagents which could improve the grade and recovery of the final copper concentrates. The investigation included sampling over one shift followed by detailed testing of the samples by sizing-assays, sizing-mineralogy and sizing-liberation. Mass balances were carried out over total streams, the component minerals and the copper contents. Some laboratory work was carried out to assess the effect of salinity on flotation. In order to handle the sizing-mineralogy calculations a computer programme was set up. The raw data were corrected for locking factors, then mineral and elemental distributions cal- culated for each screen fraction and the total sample. Calculated assays from grain counting were compared with chemical assays. Recoveries through the size-ranges re- vealed very rapid flotation of copper minerals at sizes below 350 mesh. This pointed to a possible circuit improvement by desliming rougher tailings ahead of the scavenger stage. A strong correlation was found between water in concentrates and gangue recovery for the subsieve sizes. This pointed to clean water additions to the cleaner circuit as a way to 1 Project Consultant, The Australian Mineral Development Laboratories, Adelaide, South Australia.

Jan 1, 1972