Search Documents

By S Tavelli

This discussion will present a case study in developing solutions to a metropolitan quarryÆs public relations, legal, environmental, and productivity problems. It details an extensive and detailed project to address the blasting practice in a medium sized quarry that is surrounded by residential and industrial zones. The principle work was done over four months duration during the normal production season. It included detailed drilling and blasting audits for baseline information. In addition, geologic characterisation, seismic modeling, correction of deviations from best practices, and implementation and monitoring of precise electronic timing to provide dramatic solutions for the quarry. The quarry is in the near suburbs of a large metropolitan city. It is framed on two sides by residential municipalities and on two sides by industrial zones. At the start of the project, the quarry was in court as a result of the lawsuit by one of the neighboring towns that was suing to close the quarry. The lawsuit had progressed to the advanced stage where in the Judge had appointed an arbitrator to make the decision of continued operation. This arbitrator was to observe our progress and recommend to the Judge the disposition of the case.

Jan 1, 2004

By P Trotta

The paper provides a structured methodology to investigate metallurgical problems within the operating concentrators. The strategy uses classical metallurgical data analysis as well as pulp, solution and surface analysis to determine the reasons for particular behaviours. The approach applies equally to all mineral-processing operations. To demonstrate its effectiveness a case study, based on work conducted at Pasminco Rosebery Mine, is described. In this work, the classical metallurgical analysis indicated that a significant amount of sphalerite reporting to the lead concentrate occurred as liberated particles. A combination of pulp, solution and surface analysis supported the hypothesis that the liberated sphalerite was recovered by inadvertent activation by lead ions. Laboratory studies have indicated that the use of sodium carbonate, by itself and in combination with zinc sulphate and sodium cyanide, when added to the lead regrinding mill can depress sphalerite flotation, resulting in an improvement in the lead grade/recovery curve. When this approach was tested in the plant other more dominant issues masked any positive effect the addition of sodium carbonate may have had. The plant trial highlighted the real need for additional regrinding capacity.

Jan 1, 2002

This paper addresses the area of utilising automatic data capture systems in the metalliferous mining environment for the purpose of tracking personnel and vehicles, for both safety and productivity purposes.As automatic data capture systems in the form of barcodes have revolutionised the stock control procedures in retail establishments in recent years, so too will similar systems in the form of radio frequency identification products (an electronic version of the barcode) transform the way in which many aspects of mining operations will be managed.

Jan 1, 1992

By Watson DF

Calculation of the amount of metal in an ore deposit or mining block should be approached by multiplication and integration of appropriate numerical manifolds describing the spatial distribution of the relevant variables, viz. grade, specific gravity and also thickness for bivariate data. Construction of a numerical manifold necessarily involves some form of interpolation but detailed characteristics of this are often not specified in various automatic methods, some of which even provide manifolds with discontinuities. A manifold used in calculations should describe in a geologically plausible way the spatial distribution of the variable of interest. Different approaches to the problem are discussed and compared. Particular computational inconsistencies emerge when "accumulation" is used as a variable in calculations of average grade. If an ore deposit is variable in relation to its sampling and especially if selection of mining blocks according to grade cut-off is a necessary operational decision, the biases introduced by accumulation methods can bring about serious problems of over-evaluation. Modern computational techniques make unnecessary the use of accumulations; because of potential inconsistencies it would seem unwise to use them in any ore reserve computation.

Jan 1, 1987

By S Freij, P W, R Gunawan, D Zhang, B Feng

The Mt Whaleback iron ore mine is located adjacent to Newman, approximately 1200 km north of Perth, in the Pilbara District of Western Australia. Approximately 15 per cent of the waste materials are in the zones with high concentrations of sulfide and carbonaceous minerals and are referred to as æreactive shaleÆ. The reactive shale has the potential to undergo self-heating and can react with the ammonium nitrate (AN) based explosives used in mining operations, resulting in spontaneous combustion and spontaneous explosion. The sulfide-rich shales also have the potential to produce acid rock drainage (ARD). In the present study, over 200 shale samples have been collected from different locations in the Mt Whaleback iron ore mine, including blasthole drill cuttings, fresh mine faces and waste dumps. These samples have been systematically characterised for their geochemical properties. Based on the characterisation results, a pH test was developed as a cost-effective, fast and efficient tool for the assessment of reactive ground in the mining industry. This paper summarises the results of the sample characterisations and discusses the key findings arising from the interpretation of results. These results have significant implications in the safe storage of the reactive shales and the prevention of spontaneous explosion, spontaneous combustion and ARD.

Jan 1, 2005

By G Mulder, M Adams

Since the introduction of raiseboring 30 years ago there have been many operational and mechanical design improvements in the raiseboring machine, its reamers and associated cutters. These have now made the technology of raiseboring a routine and practical operation within the underground mining world. Over the last decade these advances have been aided by the introduction of robust automation packages which have allowed unattended drilling and reaming, real time performance monitoring and enhancement and the rapid diagnostic investigation of mechanical and electrical abnormalities. The constraint to higher raiseboring performance is now the drill string. However when it comes to a cost-effective solution of applying the high drill string torque and tension necessary for the next step change in performance, designers have æhit the wallÆ. Whilst carbon fiber reinforced plastic composites with abrasive resistant sheaths may offer a solution, the limit of conventional steel, drill string technology has been reached. This limit to advancement is however based on the drill string being in tension and alternative solutions may exist by literally turning the raiseboring paradigm on its head. This paper describes the story of a small Australian company engaged in the design and manufacture of mechanical excavation machines, two Australian raiseboring contractors and three Australian mines going against tradition and pushing down rather than pulling up.

Jan 1, 1998

Mt. Whaleback, the property of the Mt. Newman Joint Venturers, contains more than one thousand million long tons of high grade hema- tite averaging 64% Fe, ranging from 70%, the grade of absolutely pure hematite, to 54%. The ore occurs in the Dales Gorge and Joffre Members of the Brockman Iron Formation. The interbedded shale bands common in other orebodies occurring in these horizons are seldom more than a few inches thick and are commonly partially enriched to about-35% Fe. In the generally hard, massive hematite orebody, the gangue minerals tend to break preferentially to the fines, or -6 mm product, and for this reason it is of a somewhat lower grade than the lumpy product. The control of the chemical qualities is concentrated on the fines product for it has been found that maintaining the iron and alumina levels in this product ensures that all chemical specifications are met in both the lump and fines products. Physical qualities are monitored to ensure that the physical quali- ties of decrepitation and degradation of the lumpy product are maintained at levels accept able to the buyers.

Jan 1, 1973

By White B

The domestic and commercial use of underground space dates back to Neanderthal man living in caves. There are many examples worldwide of the imaginative use of underground excavations, either left by mining or purpose-built. World living trends indicate that an increasing percentage of the population is living in and around major cities. Environmental, social and economic pressures associated with urban expansion can be partially catered for by a well-planned and integrated underground space regime. This paper addresses the types of underground development that are complementary to the economic and environmental pressures associated with urban expansion and high density cities. The paper explores the implications of mining and exploration technology and civil engineering, as well as the ancillary professional disciplines (legal, architecture and planning, sociology and education).

Jan 1, 1997

Mining projects draw together stakeholders with various degrees of experience in managing and assessing financial risk. When this risk is not fully appreciated or quantified, the potential for making decisions not suited to investor requirements is significantly increased. A feasibility study provides key information on project development potential, requiring detailed technical investigations with thorough financial analysis. Centaur Mining and Exploration (CME) owned and operated Cawse Nickel Operations (CNO), one of three Australian projects to develop and process vast amounts of near surface nickel resources. A technical ædue-diligenceÆ and æbankable feasibility studyÆ confirmed the large resource base, newly applied yet tested technology and relatively low unit costs would produce nickel in the lower half of industry operating costs. A number of production variables including capital requirements, delayed start-up, nickel grade, processing, maintenance and product output were outside the feasibility estimate. This was combined with exchange rate fluctuations and lower Ni prices. The inability to generate adequate cash flow and service debt repayments ultimately led to receivership and liquidation of all assets. Following the sale of CentaurÆs gold and nickel divisions, $A 784 million remained outstanding to creditors. This paper aims to define key issues leading to CNOÆs collapse by reviewing feasibility parameters, valuation methodology and project development. Some methods of assessing project viability are discussed with the aim of increasing stakeholder risk awareness.

Jan 1, 2003

Mining of the silver-lead-zinc orebodies at the George Fisher Mine officially started in 2000. A review of mining performance to date shows that many of the extracted primary stopes have experienced some degree of hangingwall dilution. The degree of hangingwall failure in the stopes became progressively more extensive throughout mining of the orebodies in 2001 and 2002, culminating in the unplanned catastrophic failure of the 744D stope in which the ore between 13C (2683RL) and 12L (2714RL) sublevels caved into the previously mined cavity between 13L (2654RL) and 13C sublevels. This was followed several months later by another unplanned caving event in a nearby stope, 740D. As a direct result of these unplanned failures it was decided to mine the stopes with a smaller span than had been previously planned and in a primary-secondary pyramidal stoping sequence. To limit the exposure of the stope hangingwall, a hangingwall drive is no longer developed and therefore geologists no longer have access to the detailed geological information that this provided. Geologists at George Fisher Mine have had to be adaptable and flexible in response to these proposed changes and rely more on data from drilling than mapping for their geological interpretation. The result is that the drilling cycle has become much more critical in the planning process.

Jan 1, 2003

By Tomlinson R. C

There are two main aspects of coal preparation to which the operational Research Executive of the National Coal Board has applied computer models. The first is in the planning of preparation plants and the first part of this paper discusses Simprep, a computer package that was designed to help on these calculations. The other is the development of control schemes to improve quality control, and the second part of the paper deals with the development of simulation techniques for this purpose.

Jan 1, 1977

Prospecting in arid terrain can produce substantial environmental impacts, comparable to or greater in magnitude than the impacts associated with actual mining or petroleum production. Impacts are likely to be particularly severe where prospecting involves intensive geophysical exploration, especially in areas which have escaped degradation by other land uses such as pastoralism. With appropriate environmental planning and management, however, the environmental impacts of prospecting in arid terrain can be greatly reduced and mitigated, at low cost. In many countries, prospecting licences, exploration leases and associated tenements now carry a range of conditions relating to environmental protection. The assessment, avoidance and mitigation of environmental impacts is therefore an important component of and-zone exploration. My aim here is to give an overview of some of the main aspects of an environmental planning and management (EPM) programme for prospecting in arid terrain (PAT). Detailed operational prescriptions for environmental protection procedures are necessarily specific to particular areas and types of prospecting: see. e.g., Buckley (1982a, 1984, 1985a, 1986a), Klepacki et al. (1985) and Stone (1986). The intention here is to provide a checklist rather than a recipe book: as an aid in incorporating environmental aspects into the overall planning and management of an exploration programme, and in liaison with company environmental staff, consultants and regulatory bodies. I also hope to show that whilst some of the techniques used in particular environmental disciplines certainly require specialist expertise, the overall design of an EPM programme is not in the least esoteric, but simply an exercise in straightforward common sense. Perhaps this paper could be subtitled: "Demystifying environmental Planning".

Jan 1, 1988

Managers are demanding efficient use of their resources and part of this demand is leading to the idea of integrated audits for Occupational Health and Safety (OH&S), quality and the environment. It is possible to construct audits which test the compliance in this area with standards established by management systems and it may be that such an integrated audit of a site could reduce the time of auditing and be equally effective as three separate audits. However, this is only a maybe. To do an audit on all three aspects when they are not fully integrated results in more time wastage than doing three separate audits. But organisations are not structured around the audit process (some financial managers may query this statement). The organisational management systems are put in place to achieve the organisational goals - presumably in an efficient and cost-effective manner.

Jan 1, 1995

By P Cepuritis, G Chitombo a, I Brunton

There is a significant amount of past evidence that links blasting and occurrences of slope failure. Particularly of great concern at Telfer Gold Mine is the effect of open pit blasting on the stability of the footwall slope above the underground portal and the stability of underground structures. For this reason, Newcrest Mining Ltd invited JKMRC to conduct necessary field measurements and numerical modelling with the following objectives:assess the dynamic stability of the footwall slope above the portal; assess the characteristics of current and future blasts in the open pit; and prepare open pit blasting guidelines that will minimise the detrimental effect of blasting on slope stability. To achieve these tasks it was necessary to develop a scaled distance attenuation curve for blast vibrations. In order to validate the developed vibration attenuation curves it was necessary to monitor vibrations from a production blast. Using JKMRC blast design software tools, the vibration of the production blast was also modelled from the blast design and vibration results from single hole blasts. The intention was, assuming that the observed and modelled vibrations were close in terms of frequency and amplitude, to use the software tools to model the vibrations of future blasts and assess their likely effect on slope stability. Numerical modelling of the dynamic stability of the footwall slope was done using the FLAC finite difference code and the UDEC distinct element code. The results of the numerical modelling and of the field measurements of the blast induced ground vibrations were combined into the blast design rules that relate distance between the slope and the blast, charge weight per delay and number of blasts necessary to cause failure of the slope.

Jan 1, 1999

By Rieniets S, Somerville J. L

In Morwell Open Cut brown coal mine, the overburden 'firehole' materials which have resulted from ancient coal fires vary-from hard baked clays to firm laminated lacustrine clays. The need to pre-strip designated areas to reduce the slope height and attain safe digging conditions for the bucket wheel excavator operation is now accepted practice at the open cut mine. In this study, the inherent spatial variability of undrained shear strength of the clay materials has been incorporated in a visco plastic, finite element based, probabilistic slope stability analysis. Data on the costs of initial pre-stripping, excavation and slope failure are collected to provide an economic basis for the optimisation of the design of the overburden batters in Morwell Open Cut. This improved stability modelling is enabling costly pre-stripping to be minimised while ensuring acceptable slope stability conditions and minimising the risk to personnel and plant.

Jan 1, 1994

A good blasting result is largely achieved by putting the right amount of explosive in the right place and firing it in the right sequence. The best blast design in the world will not break the rock if the planned blast layout is not achieved in the field. One of the critical inputs into a blast design is the diameter of the blasthole. An assumption that the actual blasthole diameter is equal to the nominal drill bit size is generally made. However, a small deviation in the actual hole diameter from that assumed will have a dramatic effect on the hole's volume and, consequently, where the explosive is placed in the blasthole. Any discrepancy in actual blasthole volume from that assumed will be reflected in 'overloading' or 'underloading' of the blasthole with the calculated explosive quantity and, thus, reflect in explosive distribution and stemming lengths. When loading to a 'collar' in an oversized hole extra explosive will be used, resulting in higher than planned powder factors and explosive costs. A blasthole diameter assumed from a nominal drill bit size is an incorrect assumption. This paper will present some actual blasthole diameter measurements illustrating the variation in hole diameters seen in the field and proposes a practical method for achieving a useful blasthole diameter measurement.

Jan 1, 1990

By J G. Petrie, H von Blottnitz

The selection and design of process options to deliver outcomes consistent with sustainable development requires simultaneous consideration of multiple objectives, within a climate of uncertainty û including the environmental and social aspects of technology management in addition to the technical and economic aspects of such. An issue of particular relevance in primary metal production is the deportment of minor and trace components within orebodies, products and wastes and the implications of such deportment for eco-efficiency û in particular, the long-term environmental impact of solid waste management practices. The identification of opportunities to enhance recovery of valuable by-products and simultaneously improve the environmental acceptability of final waste output requires a clear understanding of the distribution of the relevant ore components, which results from the choice of processing route and unit operation efficiency. This is challenging, given that process streams generated during primary metal production are generally poorly characterised and the behaviour and deportment of trace to minor and trace components is not well understood. This paper demonstrates how current data gaps and inconsistencies can be systematically addressed through the meaningful reconciliation of empirical plant data with a fundamental understanding of the mechanisms and parameters influencing element behaviour and deportment during the formation and subsequent beneficiation of mineral ore deposits. On this basis, quantitative distribution data and a comprehensive and comprehensible inventory of unit process inputs and outputs as a function of ore compositions and processing technology options can be generated, which is consistent with early design stage information requirements, both in terms of detail and accuracy, ie is æfirst-orderÆ in nature. This predictive approach to element distribution during primary metal production provides decision-makers with key information in the early design stages of a project (in terms of developing processes within the context of sustainability), whilst simultaneously guiding further data collection and environmental impact prediction studies.

Jan 1, 2006

By Tsuchiya N, Takada Y, Okabe K

Alkalis in the blast furnace are removed mainly by the slag, Alkali removal by the slag was studied as a rate process of alkali vapor- ization from the slag flowing through the dropping zone in the blast furnace. The vapor-, ization rate of I:20 from CaO-Si02-A1203 IZ20 slag was- measured under various experimental conditions. An empirical formula for the vaporization rate was obtained as a function of slag basicity, temperature and surface area per unit mass of slag. A simulation model of IC20 vaporization in the dropping zone was evaluated using the rate equation when the true velocity and surface area of the slag was de- termined from a flow dynamic model of counter- current gas-liquid flow through packed beds. The influence of the dynamic conditions of flow, as well as the slag basicity and temperature, on alkali removal by the slag was estimated.

Jan 1, 1980

Productivity of mines can be improved by taking fewer, but larger blasts. The initial blasts taken in starting a mining block are restricted by the low amount of void or space to fire into. Block cave mines are using a blasting technique to blast areas that have less than the normally accepted minimum void to establish drawbells for their orebody development. This technique used in block caving mines can be used to improve productivity in mining operations that utilise other mining methods. Some larger blasts have been done in mines, using open stoping methods, which have had void ratios as low as 13 per cent. This has been possible with the use of the explosive gases to transport the broken rock out of the area normally considered to be available to blasts. This trapping of the explosive gases in the broken rock has allowed rock to be moved over 30 m, horizontally, to allow for more void to be available in the blast area. This gives the necessary void ratio allowable to fire larger blasts. This paper will discuss the blasts where this technique has been used in mines to increase the tonnes fired in low void situations. It will also discuss where this type of blasting may improve the productivity of underground mines. Figure 1 shows the how explosive gases have enabled the broken rock to flow out of a draw point without the typical air blast and fly rock that would normally cause a rope suspended sign to be damaged beyond use.

Jan 1, 2008

It is my pleasure to deliver the first Keynote Address to the first joint conference between The Australasian Institute of Mining and- Metallurgy and The American Institute of Mining, Metallur- gical and Petroleum Engineers. I am particularly pleased to be participating in this first joint meet- ing as I have been a member of one Institute for 41 years and the other for 35 years. An examination of the membership of both Institutes confirms the fact that the mineral in- dustry is an international one. This has long been the case and basically stems from the occurrence of mineral resources in most countries of the world. It is therefore fitting that these two 'Inter- national Institutes', representing the professions involved in the mineral industry, should choose `International Resource Management' as the theme of the first joint conference. The topic of this Keynote Address is `The mineral equation' or the counterbalancing supply and demand items and the factors affecting them. I propose to attempt to present the overall picture of the mineral equation as subsequent papers and sessions will deal with specific items in more detail. My thesis is broad and deceptively simple; it is that the continued existence and growth of world material civilization depends, in large measure, on the continued use and further dis- covery of world mineral resources. Material civili- zation is used as a broad term to include the pro- duction of man's shelter and tools together with the production of the `consumer' goods and ser- vices needed by society. First let us spend a few minutes looking at the development of material civilization.

Jan 1, 1978