Search Documents

A method is presented for calculating the number of cycles of stress to failure of a drill rod from operating variables; a mathematical analysis by Cooper of the stresses present in drill steels is applied to the forged collar, i1i-in. hexagonal hollow drill steel in common use in Australia; and an estimation is made of the dry fatigue limits at various points along a drill rod.It is shown that these calculations predict failure at a 'point where failure rarely occurs, and do not predict that failure should occur where it does in practice. The reasons for this anomaly lie in the neglect of bending stresses in the stress calculations, and in failuredue to corrosion fatigue at a preferred section rather than to simpler fatigue under non-corrosive conditions.INTRODUCTIONIt has long been recognized that failure of metal sections by fatigue is influenced both by the number of cycles of stress imparted to the section (N) and by the magnitude of this cyclic stress (8). In this paper, both Nand Shave been calculated for rods which have failed in service, and whose operating history is known. While the calculation of the number of cycles to failure is·simple, the calculation of stress is more complex. The results of stress caIculations predict that failure should occur only hi short rods, and then preferentially at the tip end rather than the shank end.However, in actual fatigue failures of steel rock drill rods, approximately 75 per cent. of such failures are close to the shank end, and failures near the tip end are rare.The usual explanation given for this high incidence of shank-end failures is that at the point of failure there exists, in forged collar steels of the type common in Australia "hardness valley" or. "m'etallurgical notch". This narrow valley in hardness is a weakness, and failure is expected to occur at the weakest point at the bottom of...

Jan 1, 1955

With the proclamation of the Environmental Protection Act, 1971-80, the Environmental Protection Authority and Department of Conser- vation and Environment were established to enhance the quality of the environment. Proposed gold developments of all scales can be referred to the Authority in the form of a Notice of Intent. Environmentally significant projects might then require preparation of an Environmental Review and Management Programme. Current environmental issues include the'effects of clearing by prospectors,, mine dewatering and tailings disposal. INTRODUCTION In the past, the environmental aspects of gold industry related activities have received little attention. However, with the proclamation of the Environmental Protection Act, 1971-80, mechanisms were instituted which allowed both for referral of projects to the Environmental Protection Authority (EPA) and establishment of the Department of Conservation and Environment. As well as providing assistance to the EPA on referred projects, the Department is concerned about a number of environmental issues associated with the gold mining industry.

Jan 1, 1982

Proper technical appraisal of a coal deposit and the determination of optimum open- pit mine design can only be made after detailed examination of a number of interrelated geographical and geological factors. Initial evaluation of the geography and the overall attitude of the coal measures can often determine the most likely coal mining technique. Conclusions reached in the early stage of the investigations frequently dictate the quality and quantity of particular types of data required from further drilling of the deposit. In many cases, insufficient information relating to the overall engineering aspects of a coal deposit is derived from drilling. Little or no attention is paid in the exploratory phase to such things as the specific gravity of selected overburden samples, floor conditions, clay content of the overburden and selected strength tests on cores. This is a direct result of geologists treating coal deposits purely in geological terms without sufficient consideration being given to the engineering parameters required for a proper evaluation of the deposit.

Jan 1, 1977

By P R. G Milne

A risk-based approach to optimising pit wall slope angles was trialled in the design of a 60m deep open pit in extremely weathered and distinctly weathered materials in the Kalgoorlie area. The pit used for this approach was Stage 1 of a three-stage open pit project. The Stage 3 pit will require long term stability, as it will contain the portal for a long life underground project. Information from failures induced by steeper wall angles used in the Stage 1 pit would be valuable in predicting and preventing long-term stability issues in Stage 3. In this approach, the pit wall slopes are based not on the normal factors of safety, but on the assessment of the probability of failure and the direct and indirect costs of dealing with the failure when it occurs. In this example, the benefits and risks of adopting steeper wall angles were compared in a series of graphs. These charted the increasing probability of failure and simultaneous decreasing factors of safety with increasing pit wall slope, and the range in the possible volumes of circular failures for increasing wall angles. These were brought together in a graph showing the potential excavation savings (in BCM) and the probable cost of a failure (probability of failure times the probable volume of the failure). The resulting pit design was based on the project Mining EngineerÆs semi-quantitative assessment of where and when a higher risk of failure was acceptable and where it was not acceptable as it may have unduly affected the integrity of haul roads or production. The design incorporated wider than normal berm widths to accommodate anticipated failures and to enable modification of the wall configuration if required. Several re-designs were required during the life of the project in response to aggressively induced failures. It is considered that this risk-based approach provides a practical route to optimal pit design and operation but it requires an experienced, dedicated and efficient mining team for it to be implemented with benefit.

Jan 1, 2003

This paper explains why the valuation of mining assets is often a very different exercise from the valuation of the shares in the mining company which owns those assets. The fundamental reason for this is that mining assets, and the shares of the company which owns those assets have different risks. In order to properly value mining securities it is essential to: ò ensure all the different risks and other factors which impact on the value of the mining assets and the value of the shares are taken into account; and determine the extent to which the different risks and other factors are addressed in the value of the mining assets and the value of the shares so as to avoid double counting or not counting at all. If the alternative, but far from consensus, view is accepted that the correct valuation methodology to apply to shares in mining companies should be based on option pricing theory then conventional valuation practice of both mining assets and shares in mining companies will need to be fundamentally reassessed.

Jan 1, 1994

Ranger Uranium Mines Pty. Ltd. operates an open pit mine and ore treatment plant in the Northern Territory designed to produce 3 000 tonne/yr of U308 in yellowcake from 3 500 tonne/day of mill feed. The construction of this project was completed in 1981, 12 years after the discovery of the orebody. Wright-Davy, a Joint Venture of Wright Engineers and Davy McKee Pacific, were the Project Managers and Designers of the $270 million ore treatment plant and associated infrastructure. The project was designed in Sydney in -an office integrated with the Client, staffed by 35 key personnel drawn from Wright Engineers and Davy McKee, supplemented by personnel hired for the project. The peak Wright-Davy workforce in Sydney of 200 contained 113 design staff. The design principle of using the best practicable proven technology resulted in a plant which easily produces its design output using ore types outside the design criteria. The structuring of the project systems and industrial relations policies contributed to construction being completed within time and under budget. The plant was built without any major industrial dispute occurring and no dispute arose due to the uranium issue.

Jan 1, 1983

By Sturgul J. R

ZC Mines investigated a proposal to replace the present underground train haulage system with rear dump trucks. The number of rear dump trucks required to achieve target output and the required mix of trains and trucks during the changeover was of importance to the designers, and a GPSS computer simulation model of the operation was constructed using GPSS/PC, a recent form of the language for the personal computer. Three models were 'constructed to simulate initial and final configurations of underground haulage systems to transport ore from ore passes to the crusher and then to the skip for transport to the surface. The initial model simulated train operation on two levels and rear dump truck operation on a third level. The second model simulated rear dump truck operation on two levels with ore being loaded through the crusher to the skip as in the previous case. The third model replaced the rear dump trucks on the lower level with a train to establish the relative merits of the two methods of transport. The simulations identified equipment numbers, required operating hours and critical points in the operation which can then be addressed by the mine designers.

Jan 1, 1988

A numerical model of the spontaneous combustion of coal has been developed and is being used to investigate the nature of self-heating in underground coal mines. Results to date confirm the complexity of the self-heating reaction in coal and illustrate the impact of the factors such as the coal reactivity, mass and airflow through the coal pile. Subtle differences in the chemical, physical and environmental conditions and make a significant difference in the development of a high temperature self-heating or a low temperature benign condition, the subtlety escaping normal underground observations. Additional work is planned to investigate the thresholds for such factors in the development of spontaneous combustion and it the implications for detection by gaseous Products.

Jan 1, 1998

By V S. T Ciminelli

This work aimed at evaluating the acid rock drainage (ARD) potential of five samples of a Brazilian gold sulfide mine in a decommissioning process. Three of the most traditional ARD prediction techniques, Standard Acid Base Accounting (Std ABA), Modified Acid Base Accounting (Modified ABA), as static methods, and humidity cells as a kinetic method were tested. Both the Std ABA and the Modified ABA results indicated an acid generation potential for some of the studied samples. In the other cases the results were inconclusive. The five samples were then submitted to humidity cell tests during 27 to 30 weeks. At the end of the period, the leachate pH was stabilised in a range from 3.4 - 4.1 (four samples) to 5 (one sample). The presence of relatively high levels of sulfate and dissolved metals was detected throughout the operation, specifically, Ni and Zn, and less frequently, As. These findings are discussed with the help of the samples mineralogy and Eh-pH diagrams. The results obtained in this investigation indicated potential environmental risks of this mining area. In this particular case, the kinetic tests were shown to be essential to the identification of the samples ARD potential.

Jan 1, 2003

A real Dorothy Dix title has been selec- ted for this paper. It has the advantage, however, of being capable of being interpreted in many different ways and hence I can select my own approach. You probably are thinking that this topic would be more appropriately handled by an Accountant. I wish to make it clear at the outset that I am not skilled in the sometimes mysterious ways of Accountants - likewise that profession frequently has difficulty in pinning down economists. We have our own strange ideas about profits, marginal efficiencies, cost/benefit analysis etc. What follows is in the main a mixture of two disciplines, probably in a form that few of the purists from either side would accept. Nor do I expect the reader to accept my own prejudices. The paper is designed to stimulate thought and discussion'on the subject. Emotive words such as "profit" and "loss" make for wide differences of opinion. At the time of writing there is a surprising degree of acceptance of the viewpoint that profits in Australia are too low and one is tempted to make this point of near agreement a starting Point.

Jan 1, 1975

By Finch JA, Uribe-Salas A

The relationship between the process variables and hydrodynamics of a downflow concurrent column (Jameson cell) was investigated in both two and three-phase systems. Gas holdups from 10 to -60 per cent were obtained at gas rates up to 15 cm/s (STP), liquid (slurry) rates up to 25 cm/s, frother concentrations of 5 and 25 ppm, and slurry density (silica) up to 1.23 g/cm3 ina 3.8 cm diameter, 190 cm high column with a 0.5 cm diameter nozzle. Gas holdup decreases with feed rate and increases with gas rate, reaching a maximum (-60 per cent) at a gas rate to feed rate ratio of about one. Gas holdups were higher with slurry compared to water as feed. Stable operation was difficult to maintain at high gas rates especially with low frother dosage; operation was not possible without some frother. Instability was characterised by loss of pool level or formation of slugs. The slugs could move up or down or remain oscillatory. A quantitative relationship between the variables and gas holdup or onset of instability was not identified. Conductivity and pressure-based techniques were successfully tested on-line for estimation of gas holdup and to judge the state of operation (eg formation of slugs).

Jan 1, 1993

THOSE who dabble in m.ining are no exception to the general rule that persons who know a little of a subject are apt to think that they know all about it. Some colour may be lent to the belief that anyone may succeed in mining when we hear stories ofsuccessful diggers and others who have accidentally dropped on to something good through no foresight on their part; but we seldom hear the contra account of the far larger number who fail. Those who go more thoroughly into the subject, and take up mining as a profession, know very well that it is not one that can be carried out successfully by rule of thumb, but when they point this out to the public they are credited with trying to make it a closed profession; and outsiders are for ever trying to find out the 'trade secrets,' at the same time spurning the main one, which is hard study, experience, and the ability to apply their knowledge.The average mining man is not rich. When he amasses a fortune it is generally through speculation rather than professional work, thought no doubt his technical knowledge may have assisted him. However, making a fortune and running a mine are twodifferent things.

Jan 1, 1911

By G C. Kiel, G J. Nicholson

Corporate governance has never been more topical. A glance at any major newspaper or business publication will reveal a litany of corporate failures based upon the governance of the organisations involved (eg Byrne, 2002; Hayes, 2002; The Economist, 2002). The increased compliance requirements and speculative nature of our industry means that corporate governance systems are, if anything, more important than in the general business community (Arthur, 2001). Rather than focus exclusively on the contribution of governance to corporate failure within the mining industry, however, our objective in this paper is to examine how boards can add value to the corporations that they govern. In order to highlight how a board can add value to a company, we commence by outlining the role of the board in the modern corporation in general and the mining industry in particular. We then introduce the concept of shareholder value and identify the steps on which a board needs to focus to enhance shareholder value through value tracking processes. Our discussion pays particular attention to the importance of organisational culture to the companyÆs activities and utilises three case studies from the mining industry. We conclude with an overview of what mining boards can do to enhance their culture and drive performance changes for the benefit of the companies they govern.

Jan 1, 2002

By Opitz E. A

The integration of environmental and permitting strategies into development has become a routine part of doing business for the international minerals industry. Paralleling the development schedule with the environmental and permitting schedule is critical to ensuring that design recognises environmental constraints and that the environmental and permitting program has the right focus and achieves the objective of obtaining workable permits that reflect the project design. Regulatory issues including the law of and controls established by the country the project is situated in, the requirements of international financing institutions, international politics and the role of environmental groups and the particular precedents and processes established are all important issues that must be recognised and incorporated into the permitting program by the developer. Technical issues including collecting early environmental data during exploration, establishing hydro-meteorology equipment, baseline data gathering, and getting good environmental engineering information as a part of feasibility and design are also critical issues to the success of a project which are under the direct control of the developer. Finally tying all of these issues into a single integrated strategy under the direction and control of a nominated team is necessary to maintain focus and achieve results.

Jan 1, 1997

Kinetics of bubble-particle interaction, surface hydrophobicity and interfacial phenomena in sulfide mineral flotation are discussed in this paper. Results of the measurements of a bubble and mineral induction time (IT) and detachment force (DF), vacuum of bubble evolution (VE) and mineral floatability are discussed for pyrite, galena, chalcocite and chalcopyrite. Natural wetting and wetting induced by xanthates with different lengths of alkyl chains are examined. Experiments show the existence of several maxima of hydrophobicity on dependences of pH and electrochemical potential. These maxima are attributed as the reflection of mineral surface heterogeneity due to xanthate adsorption and the presence of cationic and anionic centres with uncompensated positive and negative charges. These charges can be neutralised by both regulation pH and applied potential. The aim of this paper is to evaluate a thickness of the rupturing film and to estimate how long the bubble-mineral interactions are according to the experimental values of IT, in order to develop a procedure for comparing of the results of DF and atomic force measurements in the same dimensionality, and to compare the results of the experimental studies on the wettability of sulfides with those predicted by the models of physics of capillarity.

Jan 1, 2005

By Sturgul J. R

A major electricity generating authority have a proposal to construct a Power Station. An understanding of the operation of the bunker system is of importance to the designers and a computer simulation model of the operation was constructed. The computer language used was GPSS/PC which is a recent form of the language designed for the per- sonal computer. The model simulated trains arriving at the power sta- tion and unloading onto conveyors which carry coal to the power station bunker. Coal was drawn from the bunker at a specified feed rate to the power station. Numerous restrictions were placed on the model, if the bunker level got too high dozers would pull coal out of the bunker onto the stockpile, and if the level got too low the dozers would push coal back into the bunker. The conveyors and dozers were unavailable due to breakdown'at various times and trains would arrive randomly about a mean interarrival time. The system was simulated for 30 years of oper- ation and the model used a basic time unit of 30 minutes so that the system was updated 525,600 times during the simulation. The results of the simu- lation gave the designers a greater understanding of the critical factors in the operation, which may now be engineered to minimise adverse Effects.

Jan 1, 1988

By Adshead ND, Blake KL, Rotherham JF, Rotherham M, De Jong G

Magnetite deposits with distinctive ¦ actinolite ¦ apatite -bearing gangue and spatially-extensive sodic-calcic wall rock alteration occur in both Proterozoic metamorphic terrains and Mesozoic-Tertiary magmatic arcs. Examples from both settings constitute significant sources of iron ore (e.g. Kiruna, Sweden; El Romeral, Chile) and some host major Cu-Au deposits that have a local association with K-silicate alteration (e.g. Cloncurry district, NW Queensland; Copiapo district, Chile). A growing body of evidence points to a hydrothermal origin for these systems involving high temperature, low S oxidized fluids. The Cloncurry magnetite-Cu-Au deposits are products of the local structurally channelized influx of a specialized high salinity ore fluid into larger-scale alteration systems developed during pluton emplacement at greater depths than those associated with subvolcanic (porphyry) Cu-Au deposits. The geological characteristics of deposits in magmatic arcs are consistent with a similar mode of origin albeit in rather different tectonic settings.

Jan 1, 1995

Ore samples from the South, Central and North ore-bodies of the King Cassilis Mine, near Omeo, Victoria, were broken and transported to Melbourne for experimental metallurgical treatment. A microscopical examination of individual unoxidised specimens, selected from these samples, was undertaken in order to thro'w as much light as possible on the occurrence of the gold which forms the valuable economic mineral in the ore.The following descriptions are the outcome' of this examination and show that very minute particles of free gold are mechanically associated with the sulphides. While the gold may be separated from the transparent gangue minerals by the flotation of the sulphides, the, actual size of the particles indicates that it is impossible to separate all the gold from the sulphides by grinding the ore to pass through a screen of 200 mesh in which the average width of the holes is 0.063 mm. Chemical disintegration of the sulphides is essential to free all the gold particles and render them available to the attack of chlorine or of a solvent.It is interesting to recall that a metallurgical investigation on the Cassilis ore in the same district by K. A. Mickle in...

Jan 1, 1933

Characterising the weight percentage of each mineral in base metal ores is an integral part of assessing the quality of an ore in terms of its processing properties. The Rietveld method, which uses X-ray diffraction data, has been applied to routinely quantify the minerals in lead/zinc and copper ores from Mount Isa Mines Limited and supergene copper ores from Ernest Henry Mining as well as their related products from the concentrators. The Rietveld method has been tested by comparing Rietveld mineral data with a standard sample with known mineral weight percentages and comparing Rietveld mineral data with mineral data calculated from elemental assays where the element only exists in one mineral such as lead in galena. Where this latter situation does not occur, the Rietveld method has been checked with both elemental and optical microscope data. In all cases, there is a good correspondence between the Rietveld data and the data it was checked against with absolute differences generally in the range of 0.5 to 3 wt per cent. The Rietveld method generally quantifies all minerals occurring over 1 wt per cent in one analysis and is less expensive and more routine compared to traditional methods such as optical microscope point counting. The Rietveld method can be applied to many stages of the mining cycle such as exploration, feasibility studies, mining, minerals processing and for environmental studies.

Jan 1, 1998

By Mackenzie J. M W

The mechanism of clay slime flocculation in coal washing circuits is considered and it is concluded that polymer flocculants are most suitable. It was found that the addition of sea water with a polymer flocculant improved flocculation and settling, and it was also found that dilution of a flocculated pulp increased floc size and hence settling rate.In predicting plant consumption of reagent it was found that cylinder tests, or even pilot plant tests, could give erroneous results, particularly on flocculated pulps. Different flocculants may, however, be compared in cylinder tests.For filtration, flocculation with Separan plus sea water was much more beneficial than flocculation with Separan alone.INTRODUCTIONDuring the mining of coal, and its subsequent beneficiation by washing, large quantities of minus 10 mesh material are produced. This fine material, which consists of broken down shales and fine coal, causes difficulties in water clarification circuits, in refuse disposal, and in filtration of fine coal.These difficulties can be largely overcome by flocculation, and this paper discusses the mechanism of flocculation, the methods by which a selection of flocculant may be made from the large number available, and the limitation of the prediction of plant performance from laboratory tests. This work applies particularly to the washeries of The Broken Hill Proprietary Co. Ltd. (B.H.P.) and Australian Iron and Steel Ltd. (A.I. & S.) .

Jan 1, 1962