Search Documents

By Marois R, Hauff P, Kowalyczk P, Lipton G, Bedell R, Neville R, Edmundo G, Ehling M, Kern R

The Canada Centre for Remote Sensing (CCRS) has developed an airborne sensor, the SWIR Full Spectrum Imager (SFSI) which detects in the Short Wave Infrared range of the solar spectrum from 1220 to 2420nm. In June of 1995, a demonstration flight was undertaken in the state of Nevada with the support of the companies listed above. The focus of the flight was to collect image data over well known mineral deposits with the objective of evaluating the applicability of this sensor to alteration mineral mapping. Some of the Nevada sites chosen include Cuprite and Goldfield, volcanic hosted acid sulfate systems; Yerington, a structurally complex porphyry copper deposit; and Virginia City, a Quartz- Sericite-Pyrite vein system with advanced argillic pods. Ground spectral data was collected with the PIMA-II spectrometer. Solar reflectance calibration was done by Desert Research Institute personnel at Virginia City and Cuprite. This paper will discuss the configuration of the sensor and present image and ground data for Goldfield and Virginia City.

Jan 1, 1995

By Phillips D. N, Herbert H. K, Fletcher A. C, Lewis R. K

Quartzite is a common feedstock used for the production of silicon by reduction at high temperatures in a submerged electric arc furnace. Silica fume, formed as a by-product in this process, contains crystalline silica in the respirable fraction. The crystalline silica in the fume represents entrained quartz derived from unreacted quartzite raw material within the furnace. A knowledge of the fragmentation of quartzite feedstock, in response to thermal disaggregation in the furnace, is important in feedstock selection to help minimise (a) the amount of crystalline silica in fume, critical from an occupational health and safety perspective, and (b) impurity levels necessary to achieve the highest possible purity of product silicon. In this study, a series of quartzites has been assessed in terms of the above requirements and correlations drawn between mineralogical and chemical characteristics. Alkaline solubility correlates with grain-size and level of stored strain in the quartz matrix. Grain-size affects the surface area available for attack while stored strain enhances the chemical reactivity of the strained matrix as well as profoundly influencing the disaggregation and microfracturing characteristics of strained grains and, hence, available surface area for chemical reaction.

Jan 1, 1995

By P Pelletier, J Tessier, C Duchesne

This paper summarises research into the study of the control of flotation processes based on froth images. A review of the froth flotation operation background and the relevance and role of the froth phase are presented. The use of numerical image analysis techniques for the extraction of significant patterns from industrial flotation froths is discussed. First, the froth was analysed by the use of the multivariate image analysis (MIA) method to extract the spectral variation contained in a RBG image. The partial least squares (PLS) method was applied to develop an empirical model for the prediction of froth grade. The results of this application are illustrated using an industrial case study. Second, the froth was also analysed by grey-level co-occurrence matrix (GLCM) and wavelet transform analysis (WTA) to extract features related more to morphological aspects. Since there is useful information hidden in froth texture, these methods are used as texture descriptor to classify different types of froths. They also provide qualitative information on the changes in the visual appearance of the froth. The pros and the cons of those methods are highlighted. Third, a control strategy based on a froth structure indicator was developed and implemented on an industrial zinc flotation circuit. The feedback controller uses the reagent flow-rate in order to maintain the froth structure at its set point. Process improvements obtained from the implemented control strategy are highlighted. Finally, the feasibility of implementing a hybrid control strategy consisting in a froth structure supervision controller based on the froth concentrate grade estimated by MIA and recovery inferred by image analysis is discussed.

Jan 1, 2005

By Zhao JC, Chen JJJ

A water/air model was developed to simulate the refining of molten aluminium by the sparging of gas through an impeller. The optimal gas dispersion depends upon selecting the correct gas rate for a given impeller rotational velocity to prevent flooding or channelling. Correlations illustrating this flooding behaviour exist for standard impellers within standard tank geometries. However the validity of these correlations has not been substantiated for gas dispersion in high temperature molten metals with non-standard tank and impeller dimensions.

Jan 1, 1995

BECAUSE of the attention given in recent years to the flotation process, there is an extensive range of equipment available to any staff detailed for: the design of a flotation mill. This statement applies not only to the flotation machines, but also to equipment for crushing and grinding, elevating the pulp, dehydrating of concentrates, and the methods of driving the various equipment.Distributed through the Proceedings and Transactions of various metallurgical societies and journals there are many excellent descriptions of flotation mills, their equipment and performance.Whilst these articles describe-in many cases in detail-the equipment in the mills to which they refer, the reasons which govern the choice of each particular equipment are not usually given.

Jan 1, 1929

By Purvis A. H, Greenwood-Smith R, Sowerby B. D

A nuclear technique for the determination of copper and nickel in bulk samples and drill core has been developed at Lucas Heights andfield-tested at Mount Isa. The technique, which is highly specific to the element being measured, utilises the gamma-ray resonance scallering process.A bulk mineral analyser was installed in mid-1976 for the routine assay of copper in bulk samples and drill cores, and remained in operation until late 1981. The operation of the analyser over this five-year period is reviewed with particular emphasis on reliability, accuracy and principal usage.The main application of this analyser was in stope planning and design whereby several thousand drill-core and Wall-chip samples were analysed. It was also used as an aid to underground grade control of stopes where ore dilution by supporting barren backfill was a problem.

Jan 1, 1984

By Hohnen CA, Limerick JM, Hall DRT

An uniquely-designed flash furnace for smelting of nickel concentrate and for the recovering of metal values from the slag generated has been in successful use for nearly six years. Within the last eighteen months the ability of the furnace to treat slag arising from converting operations without significant reduction in capacity has also been successfully demonstrated. Previously, converter slag had been treated separately in an electric furnace. The salient features of smelter developments are outlined and slag chemistry is discussed. The low cost method for the introduction of coal to partially replace light fuel oil is reviewed and total energy requirements evaluated.

Jan 1, 1984

An established method exists for the computation of rope lifetimes for shaft hoisting applications in the mining industry. In an earlier study, during the 1990s, an initial comparison of the calculated and actual rope life for various types of hoisting plants showed reasonably good correlation. In the meantime the calculation method has been developed further. The rotation behaviour of the rope during hoisting and the effects of multilayer spooling on drums are now considered in the assessment of expected rope lifetimes. The ability to determine an estimate of rope life in advance is particularly useful for mining companies. Such analysis allows them to predict the effects of rope choice in their particular application and thereby reduce the total cost of rope ownership. Such calculation techniques also allow designers of winding plants to identify aspects of the hoisting configuration that may negatively affect rope life. Often small (low-cost) changes, like increasing the diameter of head sheaves, can result in considerable improvements in rope performance. This paper describes the extended lifetime calculation method and gives further examples of the comparison between actual and calculated rope lives for operational double-drum mine hoists.

Jan 1, 2005

By Boyle L. A

A positive displacement pump is being dev eloped for pipeline transportation of coking coal to a -50 mm export specification, at a con- centration and velocity which will allow trans- portation in the plug flow region, minimising degradation of the particle structure, and pipe= line friction losses which will be lower than with turbulent or laminar flow. Pump operation is by hydraulic powered free pistons in a rota- ting cylinder block, with cylinders overlapped by stationary inlet and discharge ports in a water lubricated and sealed rotary valve. Before this development coking coal was not considered suitable for transportation in slurry form, for the valves in the double act- ing duplex piston pumps used for slurry pipe- lines, cannot be divorced from the slurry and require that the solid material must be reduced to a fines'consistency before introduction into the pump suction. The hydraulic transportation of 10 million tonnes of -50 mm coking coal, 50 km from the Bargo area west of the escarpment to an offshore shiploader at Port Kembla is feasible. Study shows that economic factors alone would dictate that the development of a pumping system for long distance transportation of coking coal is necessary. The greatest impact from the slurry transportation of coking coal would be the

Jan 1, 1976

By Pollard D, Meadows N

The presence of impurities which are electropositive to zinc in acid zinc electro- lyte causes changes to deposit morphology and reduced current efficiency. Glue may be added to control some impurity effects, but assaying for animal glue concentration is difficult and seldom done. Measurement of the activation overpotential for zinc deposition by cyclic voltammetry is used in some plants to monitor electrolyte quality and control glue additions. The deposit morphology and current efficiency of zinc deposition from commercial electrolyte were investigated for various glue additions in the presence of increased levels of antimony. Cyclic voltammetry was invest- i,ated as a method of optimizing glue additions in the presence of antimony. Scanning electron microscopy showed deposits characteristic of the impurity element present and the glue addition rate. Cyclic voltammetry measurements showed some correlation between current efficiency and activation polarization potential. The importance of using tankhouse electrolytes where results are to be related to tankhouse operation was noted.

Jan 1, 1984

By Nguyen G. H, Graham J

A laboratory-scale fluidised-bed roaster has been used to examine the effect of temperature and duration of roast on the morphology of the calcine produced from a pyritic gold-bearing concentrate. Two mechanisms of oxidation, which depend on the roasting temperature, have been identified. For samples roasted below 550°C, direct oxidation of the sulphide occurred to form hematite with a porous fine-grained concentrically-layered texture. The surface area of the calcine increased with an increase in roasting temperature in the range 400 to 500°C. For samples roasted above 550°C, the first reaction was the evolution of sulphur vapour to produce pyrrhotite, which underwent increasing grain growth as the roasting temperature was increased. This had the effect of decreasing the surface area of the calcine. The pyrrhotite was subsequently oxidised to produce hematite.Leaching studies using cyanide solution indicated that gold extraction around 95 per cent was achieved at temperatures of 500°C and above, with optimum extraction, taking into account rate and cyanide consumption in the range 550 - 700°C. Hence recovery did not decrease with decrease in surface area of the calcine. Observed gold in leached calcines was mainly enclosed in thin oxide walls of the hematite, with minor quantities enclosed in quartz and silicate minerals.

Jan 1, 1995

THE power requirements of the Mount Lyell Mining and Railway Company at Queenstown, Tasmania, have, since the inception of smelting operations in June, 1,,896, been derived continuously from the extensive forests in the watershed of the Queen River, adjacent to -the works, the firewood being of good quality, mainly composed of myrtle or beech (Fagus Ounninghami), eucalypts, and manuka (Leptospermum ericoides).The country is very rugged and mountainous, indented by numerous ravines and gullies, and intersected by many creeks, which are subject to periodical floods, under the influence of a heavy and persistent rainfall. The areas so far exploited aggregate a total of about 42 sq. 'miles, and this denuded country gives promise of ultimately becoming very valuable pastoral ground for cattle-raising. The tonnage of wood yielded per acre varies from 40 to 100 tons on stack measurement of 80 cub. ft. per ton, 60 tons per acre being considered a good average yield. The gross amount of firewood handled during the past 13 years approximates 1,200,000 tons, the greater portion of which has been obtained by ordinary tramming methods. The company's main line of railway, 3-ft. 6-in. gauge, has served as a trunk line for all supplies derived from the Queen River valley, south of the reduction works, while the northern and western areas have been exploited by means of...

Jan 1, 1911

By Gomm SA

The Mount Tom Price Concentrator, which contains a heavy medium cyclone plant for beneficiation of the -6+0.5mm fraction of low grade iron ore, is described. Testwork was carried out on an opportune basis over a period exceeding twelve months, to evaluate the separation performance of the heavy medium cyclones. Plastic density tracers were used and ore samples were taken and analysed. The effect of operating medium specific gravity (S.G.) on the separation parameters, the iron grade of the sinks product, and the mass and iron recoveries were investigated. Also examined were the differences in perform- ance between particles of different size. The implications of the findings for plant oper- ation are discussed.

Jan 1, 1987

Existing fluid flow techniques may be readily applied to the design of ranges for seam gas drainage. The Reynolds number characterises the flow regime within the pipe and it can be used in conjunction with data on absolute pipe surface roughness to determine the system friction factor. The application of the solution to the isothermal compressible flow equation utili- sing Moody friction factors and the concept of equivalent length of pipe for fittings and valves provides a practical method for sizing gas ranges. The physical capacity of a range can be decreased by the existence of significant quantities of water in the range and also by the ingress of air into the system at poor pipe joints etc. Both problems can be elimin- ated by adequate attention to design detail.

Jan 1, 1982

By M P. Sandy, J B. Simpson

The empirical stope design techniques developed by Mathews et al (1981) and refined by Potvin (1988) and others, have gained rapid acceptance in Australia in the 1990s as a simple, æfirst-passÆ means of designing primary stopes. However, it is recognised that these æstability graphÆ methods can only provide broad design guidelines. Recently published stability graphs (Hutchinson and Diederichs, 1996) encompass a wide range of geological environments, which are not discussed, and the influence of time and blasting practices cannot be easily reviewed. The æscatterÆ in the graphs must reflect, to some degree, different operating practices as well as subtle but important differences in the pre-mining conditions that are not adequately accounted for in the æmodified stability numberÆ. Development of a ælocalÆ, site-specific stability graph may overcome some of these problems. At NormandyÆs Golden Grove Operations, Western Australia, detailed reviews of stope stability performance, including Cavity Monitoring System (CMS) surveys, are undertaken for every stope, with the objective of developing a series of local stability graphs, customised to site conditions and calibrated in terms of æAverage Falloff ThicknessÆ (AFT). Cablebolting of stope hangingwalls is used to develop reinforced æbeamsÆ on each sublevel, effectively dividing the full span into smaller, more stable æsubspansÆ. By analysing stope stability performance in terms of fall-off, cost-benefit studies can be undertaken of the effect of cablebolting and other options for modifying stope spans. The approach used to develop the local stability graphs, and their integration into routine stope design procedures at Golden Grove, is described. The experience gained during stope extraction in the Scuddles orebodies has been successfully applied to the Gossan Hill æC-PanelÆ orebody. This methodology should be applicable to other underground mining operations.

Jan 1, 2000

By L E. Setiawan

The mining and milling groups at Batu Hijau are tasked with increasing SAG mill throughput by approximately ten per cent. Avenues used for this process are blasting and crushing optimisation, ore blending and predicting SAG mill throughput in relation to the geological model. This is in line with traditional æMine to MillÆ studies. At Batu Hijau, mill and mine sequencing cannot readily be configured to perform the surveys traditionally required by a æMine to MillÆ study while meeting the daily production target of 140 000 tonnes per day and processing from varying ore types in one pit. A program called BOCCOST (blasting optimisation crushing conveying optimising SAG throughput) has been implemented to capture approximately 200 variables from blasting, mining and milling operations and assign them to a common point in space in the geological model in real time. Interpretive analysis of data from BOCCOST is used to model relationships between the 200 variables to determine which and how these factors affect SAG throughput. Once these relationships are determined, the blasting, ore blending and crushing process can be optimised to generate a product that maximises mill throughput. The relationships modelled from BOCCOST are also used to generate a SAG mill throughput estimator, which can be coded into the production block model. The block model can be reconciled with the geological block model for correlation by geological domain. Once this relationship is established, SAG mill throughput domains can then be established for predicting SAG mill throughput. This SAG mill throughput estimator is then used in conjunction with revenue calculations to determine an ore cut-off, which combines these two elements to maximise metal production.

Jan 1, 2002

By C F. Prins, C LantuTjoul

Mineralisation in alluvial diamond or vein gold deposits is often hosted in trapping mechanisms. For instance, diamonds are nested in bedrock depressions such as gullies and potholes which were carved out by the sea long before the diamond deposition took place. Similarly, gold mineralisation can precipitate in the necks of a boudinage structure. In such deposits, the spatial distribution of the mineralisation is governed by the mutual arrangement of the trapsites and by the grade variations within each trapsite. Reliable estimates can be obtained only if they rest on a proper knowledge of both degrees of variability. This creates a challenging sampling problem, as during the exploration phase it is important to have a good global mean estimate to enable decision making towards the future. A similar problem occurs for local estimates at a later stage of development. To understand and manage the sampling for global means, specific sampling procedures are required based on an appropriate choice of sample support size and spacing. Estimates from such sampling campaigns should be unbiased, and the less variability they display, the better the sampling parameters. The performance and impact of sampling parameters are tested and compared on different simulated deposits.

Jan 1, 2005

The decision to contract or owner mine should be independent of, and should be made before, definitive estimated cost comparisons could be available. There is substantial potential risk of estimated cost comparisons being flawed due to difficulties in compiling comparable estimates for differing business objectives, errors and omissions or because of significant bias. In the current economic environment, escalating cost pressures potentially lead to increased incidence of disputes in mining contracts. The apparent cost of contractorÆs profit and overheads has tended to become more significant to owners. Economy-driven trends towards higher levels of performance and commercial risk for contractors, and the potential for more adversarial, difficult management; with attendant disputation between contractors and owners, have encouraged development of so-called ærelationship contractsÆ û partnering or project alliance contracts. The paper discusses the issues, circumstances when owner mining or contract mining is favoured and perceived advantages and disadvantages of contract mining. The implications of owner-perceived core business and core skills and outsourcing are also discussed. Techniques of introducing objectivity into the decision to owner or contract mine using matrix analysis or benefit comparisons are described. A disciplined procurement process should deliver a decision to owner or contract mine independent of, and prior to, any definitive comparison of estimated costs. A generic procurement process model is provided as a basis for discussion. Risk is discussed generally and as a significant factor in comparison of estimated operating costs. Consideration of risk and any prudent cost treatment are promoted as necessary pre-requisites to any comparison of estimated costs. The paper develops the concept that the decision to owner or contract mine should be based on real benefits that become obvious in the early stages of the development, particularly the procurement process; and before definitive estimated cost comparison can be available. In the context of this concept estimated cost comparisons tend to be confirmatory. Problems with comparing estimated ownerÆs operating costs with tendered contract prices are also discussed, particularly recovery of capital cost of equipment; and the owner minerÆs trade-off of operating risks for the residual contractorÆs margin attributed to overheads and profit. The paper concludes that sole reliance on a comparison of estimated ownerÆs operating costs with tendered contract prices in deciding to owner or contract mine is questionable and likely driven by a need to satisfy specific in-house customers.

Jan 1, 2003

By Sneddon J

This Is not a highly technical paper, but rather an attempt to give a general outline of coal mining for the benefit of those present who may have little or no experience in the industry, and is intended to give some general knowledge which may help to a better understanding of the problems of the industry. A knowledge of the disposition of workable material is necessary to give a comparison with other mining practices. Coal Is usually found in comparatively fiat seams of varying thickness, whereas other minerals are generally found in highly inclined lodes of variable width. However, even in comparatively flat seams unaffected by faulting, grades can, and do, vary greatly over short distances.This variation causes many local problems in working the small area affected. Even very steep seams, and some are much steeper than 1 in 1, vary considerably not only in grade, but also in direction of grade and level course. This is probably caused by folding during alteration of the shape and form of the basins after deposition.These swellies are common to most coal seams and vary only in extent. This type of variation in grade and direction of grade, while common to most ore bodies, is a matter of great importance in coal mining when it is considered that roadways are driven in the seam itself and have to be graded and made suitable for haulage purposes.The area of ground involved in an individual coal mining operation is often very large; many times larger than most metal mining propositions, and often comprises many thousands of acres.When it is considered that the specific gravity of coal may be only one-fifth of that of some ores mined, and the coal seam may be five or six feet in thickness, the vastness of the area necessary for continuous mining operations over many years will be realised.To achieve comparable outputs, with about five times the bulk of material to handle, much more ground and working places must...

Jan 1, 1947

Fission track thermochronology is a well established method for reconstructing the thermal histories of rocks with particularly important applications in tectonic studies, detecting low-grade thermal events, sedimentary basin analysis and resource exploration. These applications take advantage of the limited stability of fission tracks, especially in apatite, when exposed to the temperatures found in the upper 3-4 km of the crust. Apparent fission track ages in apatites can define an invisible 'stratigraphy' in otherwise homogeneous rock masses that can give valuable information on thermal, tectonic and erosional events. Quantitative modelling of the thermal annealing of tracks in apatite shows that distinctive profiles of apparent fission track age can be related to a number of simple thermal history styles. The main types of profile observed tend to be either an essentially linear decrease of apparent age with increasing depth, which relates to continuous uplift and denudation, or a concave-upwards profile produced by partial annealing in environments of tectonic stability or burial. More complex thermal histories produce compound profiles which are essentially just combinations of these two elements. Track length information allows the apparent age profiles to be interpreted in much greater detail. Examples of the major profile types have now been identified in various geological environments and can be analysed to give information about, for example, uplift and denudation rates, the timing of uplift or low-grade thermal events and maximum palaeotemperatures experienced during burial.

Jan 1, 1990