Search Documents

By Horiszt G

his report is going to point to that the effect of the mining dewatering on the area of Transdanubian Mountain Range has reached a phase when the cost of dewatering and providing damages can seriously jeopardize a profitable mining operation. Up to 60s the interest of mining had been dominant only, but since the begining of 80s the conceptions of industrial development and the value of enviroment protection have been changed. The natural karstwater balance of the TMR can be presented (Figure Land 2.) and the present situation of it points to that the descharge has exceeded the reacharge in 50 %. During the past 10 years the decreasing of the stored karstic water resourches was 1.1 km . The decreasing of the spring yields reached 80-82 % of the natural ones. (Figure 3-4.). Conservation of the present discharge may lead up to the totaly drain of the karstwater regime. A computer aid control system had been to develop by the bauxite mining and using of it the yield of dewatering decreased and a moderate rising of the water table has started since 1986. A recunstruction was made at the biggest thermal-medicinal lake its springs have had their source in 40 meter depth inside a spring cave at the bottom of the lake. Earlier the spring yield decreased due to the dewatering activity of mines. As a result of using of the CAC system and the providing works at the thermal sprino,the karstwater balance has got in the state of equilibrum, the first cost was decreased and spring yield was increased and the enviromental limits were adverted from the way of mining.

Jan 1, 1988

An investigation was made into the mineralogical characteristics of the upper portions of the 650 and 750 copper lodes. The investigation was based on a comprehensive suite of geological specimens representing all types of mineralization encountered during mining until the end of 1954 and the chief aims of the investigation were to determine (a) the minerals present and their textures and associations, (b) the paragenetic sequence of deposition of minerals in the orebodies, (c) significant changes, if any, which could be found in the orebodies with depth, and (d) the nature and mode of occurrence of nickel in the ore. The general structure of the orebodies is outlined and their mineral composition given. 10 textures exhibited by the ore minerals are described and a paragenetic sequence of events in the formation of the copper orebodies is outlined. No decrease in the complexity of the sulphide mineral textures with depth could be seen and no evidence was found to suggest that the tenor of the ore would decrease with depth although some factors which may eventually limit the extent of the orebodies are noted. The mode of occurrence of minor elements in the orebodies is described. Notes on the occurrence of pyrite, aikinite and berthierite in the orebodies is given and the orebodies are considered to be identified with LiIidgren's mesothermal type of sulphide ore deposit in which considerable replacement of older by younger generations of sulphide minerals occurred.INTRODUCTIONA mineragraphic study was made by Stillwell and Edwards (1945) of a suite of specimens submitted by Mount Isa Mines Limited from the Mount Isa Black Star copper orebodies with a view to determining 1. the nature, extent and association of arsenic, antimonyand bismuth minerals, 2. the mode of occurrence of silver and 3. whether galena and sphalerite occurred in minute forms and below the sizes readily observed in hand specimens.

Jan 1, 1961

By Glaessner M. F

The island chains of the Western Pacific (Fig. 1), on account of their related origin, and the similarity of the rocks that compose them, constitute in the main a most homogeneous mineral province. They lie in a complex "mobile" zone of the earth's crust, that formed a geosynclinal area separating the continental margins of Australia and South-Eastern Asia (the so-called Sundaland) from each other, and from the margin of the Pacific Ocean proper (FIg. 2). The whole region was drowned at the close of the Ice Age, as a result of the rise of sea-level that accompanied the melting of the great ice caps in the polar regions, leaving only the higher portions as islands and peninsulas, many of them separated only by shallow seas or "shelves."The geosyncline was infilled with Mesozoic and Tertiary sediments that have undergone varying intensities of folding and metamorphism, and has been subject to intermittent periods of volcanic activity, continuing into the present. Midway between the two continental margins there is a narrow belt of pronounced negative gravity anomalies, with an extraordinary S-shaped convolution in the vicinity of the Banda Sea and Celebes, that marks the core of this unstable region. The folding within the "mobile" zonetrends parallel to it, so that the islands in its vicinity, which are regions elevated by folding, are all elongated in the strike direction of the folds. This explains not only the linear shape of Sumatra and Java, but the arc of islands enclosing the Banda Sea, and the peculiar shape of Celebes.Parallel to the belt of negative anomalies, at a close remove from it, is the line of Recent, or active volcanoes, that extends along the whole length of Sumatra and Java...

Jan 1, 1947

The Mammoth Copper Deposit consists of three distinct orebodies adjacent to the Mammoth Fault. This fault is arcuate, changing from a normal tension fault to a shear strike fault just to the north of the mine. Movement on the fault was probably contemporaneous with deposit- ion of the adjacent sediments. In the upper levels the No. 1 orebody occurs within a brecciated zone in the footwall of the fault, but at depth the No. 2 and 3 orebodies are stratabound by two brecciated lithologic horiz- ons. The host rocks are impure sandstones, arkoces and quartzites, which in the mine area are near the top of the Lower Proterozoic Myally Beds. Overlying these beds is a conglom- erate siltstone sequence which has been assumed to be the base of the Gunpowder Creek Formation. North and south of the mine the conglomerate rests on an erosional unconformity representing a major time break, but in the mine the uncon- formity and conditions of deposition of the conglomerate are obscure. Some mineralization is contained within the conglomerates. The sulphides present are chalcocite, bornite, chalcopyrite and pyrite. Chalcocite is dominant in the upper levels but could be en- riched by supergene processes. At depth, bornite becomes the dominant copper sulphide with lesser amounts of chalcopyrite, pyrite and primary chalcocite. Throughout the orebody minor digenite and covellite occur and arsenic is a minor constituent bound up with the pyrite. The bulk of the sulphides occur in stringers, fractures and breccia interstices but finer grained primary bedded sulphides can be observed. The genesis is probably a complex process in- volving active tectonic movements extending from deposition to post lithification giving numerous phases of brecciation and redistribut- Ion.

Jan 1, 1974

By N McKenzie, F Brodbeck

The North-South Bypass Tunnel is the first project to get underway as part of BrisbaneÆs transport plan, which aims to improve the urban road network. The total length to be excavated is 6.8 km, which includes 4.8 km of driven tunnel and associated road connections. Construction commenced in August 2006 with project completion targeted well before the contractual completion date of October 2010. Due to the local geology, in particular the hard Brisbane tuff and neranleigh-fernvale formation, a combination of tunnel excavation methods are used. The majority of the tunnel is excavated by two tunnel boring machines which have a rate of progress of 16 - 20 m per day in rock having a compressive strength of between 80 and 150 MPa. Ten roadheaders operate at a rate of up to 2 m per day excavating the remaining tunnels, such as ramps, access tunnels, cross passages and merges. The tunnel team are managing the challenges and complexities associated with tunnelling through the hard Brisbane rock. A major challenge arose during the planning of the initial mainline excavation underneath the Royal National Association Showground in Bowen Hills. This section contains low rock cover and historical maps indicate that the showground is located within a former topographic depression (alluvial valley), which a creek once flowed through.Due to traffic merge design requirements, both tunnel boring machine (TBM) and roadheader excavation methods were required to be used in this challenging geological profile. The answer was to stabilise the alluvium above both TBM section tunnels from the surface prior to excavation and to operate the TBM in single shield mode with immediate grouting of annular void from the tail shield. In addition, the roadheader section of tunnel required additional support by spiles and canopy tubes installed from the tunnel face.

Jan 1, 2008

Acclaimed as one of the most remarkable orebodies anywhere on account of its length and richness, the Oroya Shoot occurs on the eastern side of the Kalgoorlie gold mining district close to the contact of a fine-grained with a coarse-grained greenstone, and in association with sediments. In the same stratigraphic position on the synclinal flanks of a large drag fold there are a number of other flat ore pipes, smaller, but almost as rich in tenor. Although differing in control structure they are believed to be related genetically as all show a characteristic development of a bright-green ore known locally as "green leader". Folding and bedding structures have played an important part in formation of the ore shoots.INTRODUCTIONThe Oroya Shoot is the biggest individual bonanza of Kalgoorlie's Golden Mile. It has been stoped almost continuously over a length of 4,300 ft., and about 2,000,000 oz. of gold have been won from it. Naturally pillars are not left in the best sections of such an orebody and the detailed geology of stoped out portions can only be inferred from examination of adjacent workings.No mention is made in the literature of the actual makeup of the orebody although a few structures are shown on some of the old cross sections. A diagrammatic cross section, Fig. 1, adapted from Stillwell (1929) illustrates the form of the Oroya Shoot.Gustafson (1937) drew attention to the role of folding, previously unrecognized, in Kalgoorlie geology, and indicated that the Oroya Shoot is associated with a minor drag fold on the east limb of the Brownhill Syncline, itself part of a larger left hand drag on the Central Anticline. The latter in turn appears to be part of a regional right hand fold system as shown by Campbell (1953).

Jan 1, 1959

The law relating to the Treaty of Waitangi is developing rapidly at present. A number of separate, but related, developments can be identified.

Jan 1, 1988

In the 25 years since Broken Hill's 75th Anniversary which was marked by an Australasian Institute and Mining and Metallurgy Conference in Broken hill, there have been some significant changes in the role of mines inspectors. This paper updates the information given by the then Chief Inspector of Mines, J.H. Burford, to that 1968 Conference, with an emphasis being placed on mines inspection, although it also reflects changes to mining legislation and regulatory bodies.

Jan 1, 1983

Perseverance Mine is a part of Leinster Nickel Operation (LNO), a fully owned division of Western Mining Corporation (WMC). The town of Leinster is located 370 kilometres north west of Kalgoorlie. LNO operates an underground gold mine and mill at Agnew, 30 kilometres west of the town in addition to two nickel mines and a mill 15 kilometres east of Leinster. Both the Perseverance and Rocky's Reward nickel orebodies are mined by open pit and underground methods.The Perseverance orebody was discovered in the early-1970s. Decline development commenced in 1977 and the first ore was milled in 1978. The shaft sink started in 1979. The shaft was comissioned in 1983, four years after sinking commenced. The mine was placed on care and maintenance in 1986 and purchased in January 1989 by WMC.

Jan 1, 1992

World class ore deposits can be defined commercially as deposits which contain metal concentrations in the upper quartile of resources size and/or grade, world wide, from which economic extraction can be undertaken, over a production period exceeding ten years, at a cost below the weighted average cost of cumulative production of the contained principal commodity of mines world wide.

Jan 1, 1993

By Mutmansky J. M, Organiscak J, Qin J, Bhaskar R

The results of a two-year research study into the relationship between quartz dust levels in host material and in respirable dust in continuous mining sections are presented in this paper. The experimental design and sampling procedures for underground data collection are outlined. The sample analysis procedures for quartz determination, the analysis results and conclusions of the study are discussed.

Jan 1, 1988

By A Murphy, D Lauder, J Miranda

Minera Alumbrera Limited operates the Alumbrera concentrator, treating a nominal 80 000 tpd of porphyry gold/copper ore. It is located in Argentina, 1200 km north-west of Buenos Aires in Catamarca Province, at an elevation of 2550 m above sea level. Treatment facilities consist of crushing, SAG and primary ball mill grinding circuits, rougher flotation, ball mill regrinding, gravity recovery and cleaner flotation. It is one of only a small number of concentrators in the world, which uses Jameson Cells alone for cleaner circuit flotation. Plant design was started in June 1995, with commissioning commencing in July 1997. Following a successful ramping up to design tonnages and recoveries, a number of options were reviewed to improve gold and copper recoveries. This paper concentrates on a detailed size by size flotation recovery project, commenced in May 1999. Utilising optical microscopy, scanning electron microscopy and analysis of surface chemistry it has allowed losses by size fraction to be quantified and options for enhanced recoveries to be developed. Coupled with extensive circuit surveys it has also provided an insight into previously unknown properties of Jameson Cell operation. Among these are unique residence time and bubble formation reactions to reagent and pulp flow variations, which has permitted a number of novel changes to the operation to maximise capacity and recovery.

Jan 1, 2000

By S K. Michelic, M Schickbichler, A Kharicha, E Karimi-Sibaki

The requirements for the controllability of metallurgical processes are increasingly becoming the focus of both industry and research. Advances in this field of research not only impact the stability of processes but often also influence the quality of the final product. One important way to examine processes in-depth, and thus show potential for improvement, is to describe them using physicsdriven models. In metallurgy, thermodynamic and kinetic descriptions of interactions between individual components of a system are often used to describe and analyse important metallurgical phenomena across the entire process. However, for the creation of physics-based models, boundary conditions and process variables must be implemented to enable a description that is as realistic as possible. The collection and generalisation of boundary conditions and process variables is, therefore, an important step towards functional models. The focus of this study is the determination of mass transfer coefficients between all components in a steel/slag/refractory system. For this purpose, experimental and theoretical methods are applied. Laboratory scale experiments are carried out in an induction furnace, and the mass transfer coefficients of the defined steel/slag/refractory system are calculated from changes in the chemical composition of the various components. Additionally, a calculation of the mass transfer coefficients based on dimensionless quantities is carried out. By comparing the values of the mass transfer coefficients determined theoretically and those determined experimentally in the trials, the suitability of the calculation is examined. The collection of mass transfer coefficients provides essential findings for future kinetic descriptions of inclusion modification based on the effective equilibrium reaction zone (EERZ) approach.

Aug 21, 2024

By J Hadjigeorgiou

The stability of open stopes in underground hard rock mines is influenced by several factors including the shape and size of the excavation, surrounding stresses as well as the degree of jointing. This paper presents a design methodology for stope analysis in jointed rock masses. The proposed approach relies on geological structural data to construct realistic three-dimensional joint network models. The stability of an open stope is determined based on a limit equilibrium analysis.

Jan 1, 2000

By Andrews B. S

The sinter plant at the Sulphide Corporation's Cockle Creek works produces a feed for the company's Imperial Smelting Furnace. The feed contains lead and zinc oxides and all the fluxes necessary for furnace operation. The quality of this feed is a major factor in furnace performance and the considerable flexibility of operation possible at the sinter plant has been used in efforts to achieve optimum operating conditions.Operating data is processed daily and information gathered from this source has led to three of the four improvements described.These improvements have resulted from elimination of gas recirculation, reduction of sinter returns sizing and alteration of ignition conditions and main layer fuel loading.

Jan 1, 1964

By J R. Manuel, M J. Peterson

Selected drill core samples from a Ferrobamba-limestone-hosted, magnetite-haematite skarn deposit, located in the Apurimac department of the Andahuaylas-Yauri skarn/porphyry belt of south-eastern Peru, were mineralogically and texturally characterised to gain a preliminary indication of the deposit's potential as an iron ore resource. Optical microscopy, X-ray diffraction (XRD) and scanning electron microscopy/electron probe microanalysis (SEM/EPMA) techniques were utilised to determine the characteristics of magnetite, haematite and/or goethite dominated ore types, including variations in the relative proportions and textural relationships of the ore and gangue minerals. The deportment of elements deleterious to processing performance (eg copper, sulfur and potassium) was determined and the beneficiation potential of the samples was briefly assessed. In drill core sections, the ores are grey to reddish in colour, massive and 'metallic' to dark brown and earthy in character, moderately hard and porous (macro and microporous), with variable gangue infill. Ores often appear weathered, typified by ochreous goethite staining and common minor goethite (except in dense core fragments), occasionally exhibiting a more friable texture with coarse magnetite/martite grains. Silicates and lesser carbonate gangue are visible as blue-green to beige to white scaly and/or shaly surface coatings, and finely particulate infill, often goethite stained. Sulfide-rich ore types also occur in part of the deposit, but are restricted to specific drill holes. Magnetite grain size is relatively coarse, compared with magnetite from typical banded iron formations, whereas discrete silicate gangue is mainly bladed/fibrous and/or layered and micaceous in form. XRD analysis indicates the presence of vermiculite, serpentine, stilpnomelane, chlorite, actinolite and clays. There is a spectrum of ore types representing the gradation from 'fresh' (magnetite-dominated) to oxidised and weathered (martite/goethite-dominated). Martite-dominated samples are generally higher in grade, due to leaching and removal of silicate gangue, resulting in higher macroporosity. Where gangue has been leached out, partial replacement by vitreous goethite and/or hydrohaematite is typical, often preserving the fibrous/layered characteristics of the original silicates.

Jan 1, 2009

By J J. McNee and, J Crusius, T F. Pedersen

The use of water covers is a globally-applied method for minimising acid rock drainage (ARD) and metal leaching. Although the subaqueous disposal of potentially acid-generating materials has been shown to effectively limit ARD, under certain scenarios, metal remobilisation can occur at circum-neutral pH. The following paper presents data from four case studies in which metal mobility from submerged mine waste resulted in degradation to water quality in the overlying water cover. Subcentimetre resolution profiling of dissolved constituents across the tailings-water interface (dialysis arrays), in conjunction with mineralogical information, were used to elucidate the controls governing metal mobility. The data illustrate four pathways of metal remobilisation, including: the release of zinc via the oxidative remineralisation of metal-rich organics at the tailings-water interface; enhanced remobilisation of arsenic as a result of anthropogenic eutrophication; the release of copper resulting from the pH-driven dissolution of treatment sludges; and the release of radium from uranium mill tailings due to the dissolution of radiobarite [(Ra,Ba)SO4] by sulfate-reducing bacteria. The results highlight the conclusion that the chemical stability of submerged tailings reflects both: the solid-phase characteristics of the tailings material; and the physical, chemical and biological characteristics of the depositional environment. In particular, the data illustrate that rigorous characterisation of both the waste solids and receiving environment must be performed in order to assess their compatibility. The results have relevance to the management of tailings repositories including constructed impoundments, pit lakes and natural lakes.

Jan 1, 2003

By S Karosiya, A Sharma, M Jain, N N. Viswanathan, M M. Pande, D Kumar, S Kumar

Desulfurisation of steel during ladle refining is governed by both thermodynamics and kinetics. For effective desulfurisation, thermodynamically, a low partial pressure of oxygen at the steel-slag interface and highly basic slag which possess a large sulfide capacity are desired. Kinetically, the mass transfer coefficient of sulfur in the liquid steel and in the slag determines the rate of desulfurisation. A fast desulfurisation rate is achieved by maintaining sufficiently strong argon stirring of the melt. In the present work, sulfur mass balance for steel and slag was performed after the desulfurisation treatment for several industrial heats. The decrease in the sulfur quantity of the liquid steel was more than the increase in the sulfur quantity of the slag. The discrepancy in the sulfur mass balance suggests that the sulfur could be transferred to: (a) the gas (via slag) phase; or to (b) the refractory (crucible) phase. The preliminary investigation of the refractory samples taken at slag-refractory and steel-refractory interface showed no interaction of sulfur with the refractory. Therefore, the possibility of sulfur transfer to the gas phase was verified by carrying out melting experiments of sulfur containing slag in an argon/air atmosphere. Sulfur containing slag was initially melted in an MgO-C crucible under an argon atmosphere followed by creating the air atmosphere just above the melt. Careful sampling and analysis from the cold spots of the crucible, much above the melt surface, revealed formation of a fibrous structure. Scanning electron microscopy energy dispersive X-ray spectroscopy (SEM-EDS) analysis of these fibrous deposits confirmed the presence of oxides and sulfides. Oxidation of sulfur containing slag under air atmosphere was also performed using a thermogravimetric analysis (TGA) set-up. It showed a constant sulfur loss in the range of 1300– 1500°C. Thermodynamic calculations carried out using FactSage™ ver 8.3 for these experimental conditions are in good agreement with the observed results.

Aug 21, 2024

By E Rubio, N Morales

Currently, mine plans are optimised by using several criteria as objective functions, like profit, life-of-mine, concentration of some pollutants, mining costs, confidence level or ore resources, with consideration of constraints related to production rates, plant capacities and grades. Whilst this approach is successful in terms of producing high value production schedules, it uses a static opening sequence of the drawpoints and therefore the optimisation is made within the level of freedom left by the original opening schedule, and as a result it is far from the true optimal value of the project. This paper presents a model to optimise the sequence of drawpoint opening over a given time horizon. The emphasis is in the precedence constraints that are required to produce meaningful operational sequences considering the exploitation method (panel or block caving), physics considerations and logical rules. Further on, while it applies the standard approach of maximising net present value (NPV), it considers other targets for optimisation, like the robustness and constructability of the plans. Finally, it applies the model to real data to obtain feasible plans by means of this model. The first tests were done varying the production capacity of the mine.

Sep 26, 2011

By V Malysiak, N J. Shackleton

In the flotation of platinum group minerals pyroxene is a major gangue mineral. This study shows using zeta potential and ToF-SIMS analyses that when pyroxene is exposed to copper, nickel and/or calcium ions in solution at alkaline pHs a surface reaction occurs between the hydroxy species, in the case of copper and nickel, or divalent calcium ions and the pyroxene surface which influences the floatability of the pyroxene. Following exposure to copper and nickel ions at pH 9 addition of SIBX resulted in the pyroxene floating readily. It is also shown, in the case of copper, that the activating effect of the adsorbed copper hydroxy species can be reduced by the addition of complexing amines prior to SIBX. Proposals are made to explain these observations.

Jan 1, 2005