Search Documents

By Biswas AK, Hayes P

During the reduction of iron oxide pellets in the blast furnace it has been found that catastrophic swelling (up to 300% volume increase) can occur. Although the burden preparation conditions can be designed to avoid this phenomenon the exact reason and mechanism of the swelling has yet to be clearly identified. Swelling of the burden is undesirable since it reduces the interparticulate voidage in the blast furnace thus reducing gas flow through the stack resulting in low production rates of iron. The present study differs significantly from previous experiments in that reduction is carried out on single crystals of wustite thus the problems of control of gas composition and specimen preparation are minimised. The microstructures formed on reduction have been examined by optical and scanning microscopy. Pure wustite and wustite doped with various levels of CaO have been examined after reduction in controlled CO-CO 2 gas mixtures at 968¦C. The catastrophic swelling on reduction coincides with the formation of an unusually open iron structure in which the iron appears as whiskers or needles as previously reported. The spacing and thickness of the needles are shown to vary with impurity content and gas composition. Metallographic examination has shown in addition, however, that the whiskers do not necessarily constitute the only product form of the iron produced and in CaO containing wustites with less than - 2% CaO there is a transition from needle growth to porous growth of iron. Thus the % swelling of the oxide particles is dependent on the initial size of the oxide grains. Samples of FeO - 10% CaO exhibited a previously unreported product inorphology associated with the nucleation of 2CaO.Fe203.

Jan 1, 1980

The present-day arrangement of old ( ? ) Palaeozoic and Mesozoic metamorphic rocks in eastern New Guinea lends some support to the concept of tens:konal dilation in Upper Cretaceous to Lower Tertiary time, It appears that the metamorphic core of the Morobe Arc (Glaessner, 1950) could have been rifted from the eastern flank of Cape York Peninsula, and then been carried north-eastward by some unspecified sub-crustal. tangential force. In the early stages of the rift it is thought.that submarine basalts may have extruded up the .'tension .scar and spread across the floor of the opening rift. Thick clastic muddy sediments derived almost exclusively from the rifted block were then spread across the floor of the opening rift. Later ~ertiary lateral movements from east to west along the Markham-Ramu Fault appear to have bent the northern end of the Morobe Arc towards the.east,,causing the intense folding in the sediments of the Aure Trough.

Jan 1, 1962

By Sneddon A

Expansion of central production facilities at the Kutubu Petroleum Development Project in Papua New Guinea (PNG) required excavation of a steep hillside overlooking operating crude oil processing, storage and pumping facilities. Drilling and blasting were used to remove a large volume of rock which varied from hard limestone to soft sandstone, with zones of soft clay and many underground caverns. Similar ground conditions had made it very difficult to predict and control blast-ing results during previous excavation in this area.Special conditions of the project included restrictions on ground vibration levels at a high pressure oil pipeline and pump station within 100m of the blasting area, and a prohibition on any flyrock. As work progressed, some blasting was necessary with 20m of installations being constructed on the levelled project site. Thus blast design, drilling and charging were carefully controlled to avoid any incidents which could interfere with oil production or progress of the construction project.

Jan 1, 1994

By H Kundapen, J J, C Rumble, S Miller

This paper describes measures taken by Ok Tedi Mining Limited (OTML) to minimise the risk of acid rock drainage (ARD) resulting from mining operations at its Mt Fubilan porphyry copper-gold mine in the remote Star Mountains of Papua New Guinea. The risk of acid generation and metal leaching as a result of oxidation of these sulfidic deposits has long been recognised by OTML. In 1998, OTML instigated the ARD Management Program to fully evaluate these risks and to formulate, if necessary, trial and implement appropriate management strategies. In implementing the ARD Management Program, OTML has adopted a risk management approach consisting of five stages: risk identification, risk analysis, risk assessment, risk treatment, and review and monitor. Significant progress has been made in relation to risk identification, analysis and assessment. The work currently underway to put in place a comprehensive risk treatment and review process will ultimately determine the success or otherwise of this approach.

Jan 1, 2003

During the 20th century, the iron ore mining industries of Canada and the United States passed through several periods of transformation. The beginning of the 21st century has seen yet another period of transformation, with the economic failure of a number of steel companies, the acquisition of their facilities by more viable steelmakers, and the consolidation of control within the North American iron ore industry. Changes in Canadian and United States iron ore production and the market control structure involved are analysed. The consolidation of ownership, formation of foreign joint ventures within North America, planned divestitures of upstream activities by steelmakers, and industry changes made to ensure availability of feedstocks will be reviewed. The traditional isolation of the Canadian and United States iron ore operations and their strong linkage to downstream steel production will be discussed in the context of a changing global economy. Management-labour conflicts that have taken place and agreements made during 2000 through 2004 will be discussed in the context of the economic environment leading up to these agreements. Cooperative agreements between competing Canadian and United States companies to resolve client needs in processing and blending will be examined. A joint industry-government project designed to use new technology to produce direct reduced iron nuggets of 96 - 98 per cent iron content using non-coking coals will also be assessed. Changes in iron ore transportation methods, ownership and infrastructure will be reviewed for both rail and inland waterway transport between Canadian and United States companies. A brief analysis of social and environmental issues relating to sustainable development of the Canadian-United States iron ore industry will be included.

Jan 1, 2005

By X X. Qiu, T Zhang, B L. Wang, X Qiu, Y H. Du

This paper summarises the information about current state of eco-environmental problems, geological disaster and mining waste causing during the process of limestone mining. By comparing the management experiences of limestone mines in other countries, management problems in China have been discussed and improved management options have been proposed here. These options include: accelerating the process of legislation, promoting and strengthening environmental impact assessment for limestone mine, and increasing compensation requirements according to the local eco-environment conditions.CITATION :Wang, B L, Qiu, X X, Qiu, X, Zhang, T and Du, Y H, 2012. Eco-environmental problems caused by the process of limestone mining and management options, in Proceedings Life-of-Mine 2012 , pp 357-360 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By Munive L

As a result of commissioning No.5 B F, 2670m3 inner volume, in March 1972, the largest B F in Australia; new expertise in maintenance, furnace operating practices and design have been obtained. This experience has also been extended to the other furnaces. A series of operating problems were con- fronted; all parts of the furnace, including the hearth side walls and bottom,were adversely affected. In December 1977, serious hearth wall wear was detected at No.5 B F, and a potential hearth breakout was averted. Hearth wear in No.4 B F was discovered in March 1979, and emer- gency underhearth cooling was installed to reverse an extremely advanced hearth bottom erosion. Hearth behaviour of No.5 B F oampaign 1972-1978 and`No.4 B F campaign commencing 1972, has been studied and discussions on the causes, effects and measures undertaken to protect the hearths are presented in this paper.

Jan 1, 1981

By Edmonds W, Giles C. W, Webb R. J, Gum J. C

Gold production from The Granites - Tanami Goldfield during 1993 is expected to exceed 8 t, eclipsing that of the traditional Northern Territory gold mining districts of Tennant Creek and Pine Creek. This is the result of dedicated and successful exploration, and the consequent discovery of new orebodies such as those at Dead Bullock Soak.Following granting of access to regional exploration areas in 1988 and identification of favourable host rocks in the Schist Hills area, North Flinders Mines (NFM) began a methodical exploration program of detailed geological mapping, rock chip sampling, costeaning and various types of drilling. The first resource of 600 000 t of 3.3 g/t gold was announced in mid-1989. This has grown progressively with systematic exploration to the currently published resource inventory of 6.6 mT @ 5.4 g/t, (as at 31.12.92) contained in six separate orebodies within the Dead Bullock Soak Mineral Lease at Schist Hills.

Jan 1, 1993

Before commencing design of a coal prepar ation plant, it is essential to have detailed information of the raw coal to be treated to- gether with a clear understanding of the products required. Prediction of raw coal size distribution, particularly the amount of fine material, is difficult and the methods employed should be large scale pilot plant studies or techniques to simulate coal degradation and shale breakdown in water. A detailed knowledge of well proven coal preparation processes and new developments allows processes and process combinations to be compared to'obtain the maximum economic recovery when using lower cost, less efficient processes within acceptable limits. Equipment should be selected bearing in mind its precise application and the location where it is installed. Plant layout should be carefully studied to minimise equipment requirements and to simplify construction. Measurement, control and automation should be an integral part of plant design in order to obtain the optimum performance of the processing equipment.

Jan 1, 1974

By Umar N

Traditional exploration has been undertaken by both local and overseas experts to discover tin deposits in Indonesia over almost 300 years. Indonesia is part of a tin belt which runs from Myanmar in the north through Malaysia to Singkep, Bangka, and Belitung islands in Indonesia in the south. The discovery of alluvial tin deposits is becoming harder as the more obvious geological targets are exhausted and topographical conditions become more difficult. New approaches are required to sustain successful exploration. There are indications that tin deposits can be found at depth on-shore as well as off-shore. These deposits are found associated with tough clays. On-shore tin exploration is hampered by swampy areas, while the off-shore search is often affected by difficult sea conditions. These factors lead to increases in the cost of exploration as well as the cost of subsequent production. Tin price fluctuations and environmental issues are also of major concern in the planning of the future operation of tin mining in Indonesia.

Jan 1, 1996

This paper outlines the mechanism of Stress Corrosion Cracking (SCC) and how it can cause premature failure of rock bolts. SCC occurs due to the progressive development and growth of cracks in the surface of a metal, and it is caused by the combined effects of stress and a corrosive environment affecting susceptible metals and alloys. It can occur in most metals including stainless steel. It is not a new phenomenon, but its effect on rock bolts has only been recognised recently.Rock bolt failures caused by SCC appear to be brittle failures which occur at less than the ultimate tensile strength of the bolt. In the mining industry, SCC failures of rock bolts can occur a few months, or after many years of exposure to stress and a corrosive environment. If SCC of rock bolts is suspected, then the rock bolts should be examined by a metallurgist, and steps should be taken to reduce the problem.

Jan 1, 1998

Any engineering firm hoping to do business in the modern world must understand-and take into account-the social and economic realities of client, country, culture, and community. If these considerations are ignored, any large-scale international development project is doomed to failure even before it begins. In this changing world, the distinctions between `developed', `developing', and `less developed' nations are more and more blurred. The so-called `less-developed' and `developing' nations are rapidly acquiring technology, an educated man- agerial and technical class, manufacturing capa- bilities, a growing spectrum of developed financial and raw materials resources, and a broad range of labour skills. These nations are establishing themselves as an integral part of the modern world, on an equal footing with other nations and with justifiable expectations for an ever higher standard of living and an ever better quality of Life.

Jan 1, 1978

While, in the past, a great deal of attention has been focussed on technical issues and the performance of explosives in rock, the explosive user, an essential link in the chain, has often been neglected. In the mining industry, too often, the benefits of excellent technical work have been degraded over time due to the lack of definitive and documented control. Using the principles of quality management a quality training system was developed and implemented for management of explosives use at Gunpowder Copper Ltd (GCL). This paper describes the structure of the system, its development and implementation, and contains practical advice and information for managers responsible for blasting and charge crews. The paper is in four parts: I Quality systems. A brief overview of the relevant aspects of total quality management that apply to explosives use. The requirements for documentation, management and auditing are explored. 2. Training for competency. The five essential elements of Competency Board Training (CBT) are examined, including auditing. 3. The Gunpowder Copper system. Implementation of the complete training system. Documentation and its control, auditing, instructions for operators, management responsibility and means of obtaining operator ownership are amongst the issues raised. Reporting requirements are the means to effectively manage change are described. 4. Summary. The paper concludes with the tangible benefits seen by Gunpowder Copper through the adoption of a quality training System.

Jan 1, 1995

By Wharton P, Voigt R

In order to do the discharge estimation better, it is valuable to find out appropriate formulas for estimating discharge in various pits, based on accumulating data, summarizing discharge patterns applying optimum seeking method and principle, by seeking redical exponent with help of the method of exhaustion, as well as testing and making statistics, in accordance with the quality standards established by our practical experience.

Jan 1, 1988

Stressed steel cables, similar to those used in pre-stressed concrete, have been used for rock mass reinforcement, in civil engineering, for many years. This type of reinforcement has been attempted for open pit wall support, on several occasions, but has never gained wide acceptance as a practical approach because of high cost and complexity of installation in a mining environment. On the other hand, untensioned, fully grouted cable dowels (cable bolts) have gained wide acceptance for ground support in underground mining and it is perhaps surprising that this technique has not been used to a greater degree in open pit mining. The first systematic application of this technique in Australia was at the Mary Kathleen uranium mine in 1976, where it was spectacularly successful in maintaining steep stable walls in a jointed rock mass with unfavourably dipping structures. Cable bolting, and other techniques, are now being used to an increasing degree for wall support in both small and large open pits, for two basic applications: 1. stabilisation of potentially unstable sections of a wall, or 2. to allow steeper walls and reduce waste stripping volumes. In virtually every situation, wall rein- forcement has significant economic as well as technical advantages. The paper describes the development of the techniques, the mechanisms of wall support, the methods used, and discusses several case histories of its application to Australian open pit mines.

Jan 1, 1986

By N LaBranche

The resurgence of Silicosis and Coal Worker’s Pneumoconiosis (CWP) in coalmines has placed the spotlight back on the management of worker exposure to particulate matter across all mining sectors (Coal Workers Pneumoconiosis Select Committee, 2017). There already exists a substantial body of knowledge on particulate matter and its impacts upon human health (National Academies of Sciences, Engineering and Medicine, 2018). The contribution of silica to respiratory disease is well known. However, it is also clear that there are major gaps in our understanding. In part, those gaps relate to the contribution to adverse health effects of mineralogical constituents in the dust (LaBranche et al, 2021a). It is also becoming evident that the size and shape of the particulate matter can affect its potential impact on human health. The University of Queensland has developed a methodology for characterising respirable and inhalable dust samples using scanning electron microscopy. Multiple samples from numerous mining operations have already been analysed using the UQ methodology. The process has been successful in showing the variety of mineralogical components and particle size distributions present in various areas of the mines.

May 5, 2022

By Fullagar P. K

In resource definition and mine development, major capital expenditures are committed on the basis of sparse information and even in production surprises such as bad ground are not uncommon. Drill holes constitute the principal source of information about the orebody and its environment and optimisation of drilling implies maximising the yield of useful information per dollar expended. Geophysical borehole logging provides new flexibility for optimising the drilling budget. Economic benefits can flow from geophysical logging at all stages of the mining cycle. The most commonly cited benefit is substitution of diamond delineation drilling with cheaper percussion or reverse circulation drilling in cases where geophysical logs can substitute for core. This approach can deliver an attractive direct saving in drilling costs (and time) if drill meterage is unchanged, or a potentially greater indirect benefit from better ore control if more holes are drilled within the original drilling budget. More ore contact intercepts per dollar can translate into lower dilution and enhanced ore recovery, thereby increasing revenue as well as reducing mining costs. Substitution of diamond drilling with percussion drilling is not always feasible. However, geophysical logging of diamond holes is often highly advantageous in its own right, both for geotechnical characterisation as well as ore delineation. Operational advantages of logging include data objectivity, speed of interpretation and reduced core handling and analysis costs. Geophysical logging assists mining engineers by providing a continuous measure of in situ rock strength, even over intervals with poor core recovery. The additional expense of geophysical logging in blast holes can be justified in terms of more accurate ore boundary delineation and rock strength evaluation. Precise ore boundary delineation permits refinement of charge placement, to minimise dilution and maximise recovery. Detailed knowledge of rock strength can enable optimisation of blast design. Rock strength can be evaluated in real-time via analysis of drill performance data recorded with measurement-while-drilling (MWD) technology. To successfully apply geophysical logging in mines, its technical, operational and economic viability must all be established. This entails verification of the existence of appropriate physical property contrasts, investigation of the best way to integrate the geophysical results with the mining method and an objective assessment of the value of the resulting mine performance benefit. Geophysical logging is already well established in many mining operations. The greatest impediments to its wider utilisation at mines are: lack of appreciation of geophysics by most mine geologists, engineers and managers; limited interpretational aids; and the necessity to re-enter completed drill holes. In this paper we endeavour to address these issues by informing mine geologists about potential applications of geophysics, by illustrating automated interpretation of geophysical logs and by highlighting the importance of emerging MWD and logging- while-drilling (LWD) technology.

Jan 1, 1997

By Mann LD

The Haveluck gold deposit, located 2.5km north of Meekatharra, contained 1,284,000 tonnes at an average grade of 1.8 g/t gold of drill delineated proved and probable ore prior to commencement of production. Following successful laboratory and pilot scale testing a decision was made to establish a 300,000 tonnes per year heap leaching operation. The ore, crushed to minus 100mm was stacked on an impermeable membrane and irrigated with a dilute cyanide solution. Gold was recovered from the resulting pregnant solutions by adsorption onto activated carbon and gold bullion produced in a modified Zadra process desorption plant. From the commencement of mining it was obvious that a high percentage of fine material was being produced which would adversely affect the percolation of the cyanide solution-through the leach heaps. A screening plant was incorporated into the crushing circuit which provided an oversize product satisfactory for heap leaching and an undersize for carbon-in-pulp treatment. Plant design provided for the slurrying of minus 0.8mm ore before feeding to the pachuca tanks. Initial practice was to use four tanks for gold dissolution and two for carbon contact. Vibrating screens were used through- out for the carbon-ore separation and the loaded carbon was stripped in the existing desorption plant.

Jan 1, 1982

The Ok Tedi open pit mine will have final wall heights in excess of 750m. The behaviour of these excavated slopes will be influenced by the presence of numerous defects. This paper discusses the identification of possible failure mechanisms within the pit walls based on mapped fault and joint data. Results from analyses using these data have formed the basis for the ultimate pit design.

Jan 1, 1994

By M D. Rosengren, G Gregor, M F. Young

Over the last 15 years the silver/lead/zinc ore treated at Mount Isa became increasingly complex and lower grade. Metal recoveries dropped dramatically, causing a serious decline in profitability. The ætraditionalÆ response of increasing tonnage to reduce unit cost was unsuccessful, since the additional tonnage was even lower quality ore. A major technical and capital program in the 1990s restored metallurgical performance, but business return was still too low and ore quality continued to decline. In 1996 a new, holistic approach integrated the steps of geology, mining, concentrating, smelting, and refining. Previous assumptions about æfixedÆ and æmarginalÆ costs in mining and processing were shown to be wrong. Detailed analysis showed that some ore sources were reducing profit. This led to a fundamental redesign and downsizing of both Mount Isa and Hilton mines. The result was dramatic increases in head grades, metallurgical performance and plant stability without any capital expenditure. The business is now smaller, but more profitable.

Jan 1, 1998