Search Documents

By Hollis R. G, Tuppurainen J. M I

Improved control of non-ferrous sintering operations requires the on-line measurement of sinter quality. No on-line measure of sinter quality is currently available, however, previous work has shown that the raw mix chemistry and peak sintering temperature determine the mineral phases formed and hence the resulting Blast Furnace behaviour. Control of these factors should therefore lead to improved quality control. In this paper, the development of a simplified heat and mass balance model of the Sinter Plant at Mt Isa is described. The model used available plant data to calculate raw mix composition and a simplified reaction scheme to predict sinter composition. The extent of reaction is inferred from the flue gas analyses. Off-line testing of a dynamic version demonstrated that actual plant performance could be predicted with reasonable accuracy.

Jan 1, 1989

By K Koskinen, S Ronkainen

The flow field induced in an Outokumpu TankCell and by an OK rotor-stator mixing device in a laboratory and a process size flotation cell was modelled numerically using computational fluid dynamics (CFD). The primary target was to discover and reproduce the various interactions between the flow field and the flotation cell by numerical means. As power consumption depends sensitively on flow field, it can be regarded as a top-level derived quantity (or measure/metric) indicating the validity of the numerically obtained flow field. Having properly validated numerical means to produce the flow field the influence of various design parameters can be captured with certain accuracy. In addition, separate gas and solid phase models for bubbles and solids, respectively, were implemented. The comparisons between velocities and turbulence quantities measured using the laser doppler velocimetry (LDV) technique and CFD modelling were performed. The grid generation was performed with the commercial Gambit 1.3 and the subsequent integration and solving of the resulting algebraic equations with the commercial CFD-code Fluent 6.22. The computationally economic multiple reference frame method was included to model the moving rotor blades. Gas and solid phase models were modified mixture models.

Jan 1, 2005

In North-West Nelson the Riwaka Complex, a linear basic intrusive complex, is exposed for approximately 45 kilometres. Some 500 kilometres south, across the Alpine Fault, a linear zone of similar but less well known basic intrusives that may be correlatives of the Riwaka Complex is exposed discontinuously for about 80 kilometres. The Complex was emplaced at several centers along a major tensional fracture zone that developed in upper Carboniferous to Lower Permian time. This fracture zone probably formed in response to the development of a west dipping subduction zone that gave rise to the Permian volcanic arcs in east Nelson and western Southland. The Riwaka Complex contains three rock suites. The Fractionation Suite, characterized by cyclic mineral layering and small scale cumulus banding is the largest and is divided into the Ultramafic, Hornblende and Plagioclase Series, each of which is subdivided into several units. The Cumulus Gabbros represent a restricted but important suite of unusual composition, while the third suite is the late phase Diorite Suite.

Jan 1, 1980

Commissioning is one of the many phases of a project, it has inter-dependencies with the other phases, as they have amongst themselves, and has its own terminology and distinctive features. Commissioning time and cost can severely affect project economics, especially through unrealistic estimating, and requires a separate management team to ensure full control is. maintained. Targets to be achieved in commissioning are identified, together with the necessary policies to achieve them. Factors which have to be taken into account in applying these policies are Discussed.

Jan 1, 1986

By D Cai, E Baafi

Various enabling technologies and systems have recently been introduced in the mining industry. Such systems include miner-bolters with concurrent cutting and bolting, employment of two shuttle cars, adoption of self drilling bolts and utilisation of continuous haulage or monorail systems. The paper discusses how Flexsim discrete event simulation models were used to assess how these proposed mining systems can best be used to achieve and sustain high roadway development rates of 10 m per operating hour for 20 h/day.

Sep 26, 2011

By Denby B, Miles N. J

The underlying theory behind the construction of an on-line size analysis system is described together with an introduction to the Artificial Intelligent techniques that it is founded on. Previous systems based on more traditional technology such as edge detection and dilation algorithms have been restricted by the significant processing power they require, this has resulted in the production of systems with either reduced functionality or severe hardware requirements. A neural network approach offered a new perspective to the problem of size analysis; the ability of a network to learn and recognise subtle patterns in training data before on-line processing is initiated opened up the possibility for the production of a fully functioning practical system. The format of the training data had to be carefully analysed prior to its implementation in a neural network as the capability of a neural network solution depends as much upon a suitable data preparation as it does on the system architecture. To facilitate experimentation with various profile quantification techniques such as fourier and fractal analysis an Image Profile Analysis System was constructed (IPAS) in software on a personal computer. The IPAS system was produced with the aim of pre-processing image data to create data sets for experimenting with external neural network packages. The system allows the analysis of both real images obtained by image capture and simulated images created by an in-built in simulator. A measurement comparison scheme is also included together with a case study concerned with the frequency analysis of simulated images. The power of neural networks combined with the data compression provided by profiling removes the need for direct measurement of individual particles. This has obvious implications on the level of hardware necessary, and ultimately the expense of a stand alone system. The extrusive nature of data collection via an image analysis system will also permit simple installation of a shipped system; eliminating any requirement for interference with existing machinery.

Jan 1, 1995

By B J. Andrew, M R. Daley

Mount Isa Copper Mines is a world-class mining operation producing approximately six million tonnes of ore per annum. With over 50 years of mining history and over 76 million tonnes of underground resource remaining there are many challenges facing the mine technical team today and into the future. The mine consists of nine distinct areas: the Hangingwall Lens, Footwall Lens, 1100, 1900, N1100, N1900, 3000, 3500 and N3500 orebodies. Each of these areas have different characteristics, requiring varying methods of mine design and ground control for safe and efficient orebody extraction. Each of the areas operate with an independent sequence whilst interacting with the entire underground operation. Within the first five years after graduating mining engineers tend to orient their careers in either a technical or operations direction. Engineers working towards a specialised technical career will often be working as mine planning engineers, whilst others more focused in the operations stream occupy roles such as operations or project engineers. At this stage of a mining engineerÆs career they are not yet categorised into one stream or another, but career decisions made now can generally focus their ultimate career path in one direction or the other. Due to the size of the Mount Isa operations there are many opportunities for engineers pursuing both career path and plenty of room for growth forthose as yet unsure.

Jan 1, 2005

By T QUINLAN

A resource estimate uses data obtained by sampling an orebody. An example is described in which a random drilling pattern did not provide a representative set of assays, and the estimated resource was significantly less than the mine production. It is believed that a better estimate would have been made if the exploration holes had been drilled on a regular grid.

Jan 1, 1992

By K Le Bron

Fatalities that occurred because of rock falls in off-reef excavations (excluding shafts) over the last three years range between ten per cent and 20 per cent of the total number of fatalities that have occurred due to rock falls in the South African mining industry. These rock falls, mostly exacerbated by blasting practices, occur because of failure on discontinuities within the rock mass. Among other reasons of their occurrence is insufficient support installation or the incorrect assessment of rock mass conditions. This report presents qualitative analysis intended to outline rock stability conditions in tunnels subjected to dynamic loading. Seismic waves including those created by firing an explosive charge in tunnel rocks are considered. The rock behaviour is monitored using geophones and extensometers variably installed to record the near and far effects of roof bolt support units on a dynamically loaded rock. The paper discusses the results of field investigations.

Jan 1, 1999

By Shklyar FR, Bokovikov BA, Gordon YM, Scherbatskii VB, Yaroshenko YG, Shvydkii VS

The paper presents, for the first time, a complete mathematical model of the flow of gases in packed beds which describes the processes of gas-mechanics in iron blast furnaces and other shaft type smelting units. Good correlation between calculated and experimental results was obtained confirming the adequacy of the model. It is shown that the uniformity of gas distribution is related to the tuyere size and the extent of its protrusion into the furnace and that these variables may be used to regulate gas distribution across the furnace diameter. It is also concluded that furnace height has no significant influence on gas distribution. The necessity for a mathematical description of raceway phenomena has been experimentally proved. Conclusions from theory are shown to have profound implication to furnace design and operation.

Jan 1, 1975

By L Smith, R Beckie

An intermediate scale (8 m + 8 m + 5 m high) constructed waste rock pile experiment was built upon a contiguous grid of 16 gravity drainage lysimeters to investigate the flow of water in unsaturated waste rock. Average net infiltration to the uncovered waste rock pile is 55 per cent of precipitation. Large rainfall events have net infiltration of 55 per cent to 85 per cent. Net infiltration estimates range from 23 to 120 per cent of precipitation between lysimeters. Small-scale lysimeters of less than 4 m2 area are shown to be poor predictors of net infiltration for uncovered waste rock. The appropriate size for lysimeters increases with increasing flow rate. The residence time distribution has an estimated median value of 3.0 to 3.9 years under average infiltration conditions. Water flows within the fine grained matrix, within larger pores (macropores), and in matrix free areas of the pile. In situ tracer concentrations vary between pore sizes, and between spatially distinct areas of the pile, indicating water geochemistry may also be variable. Water samples collected from in situ soil water samplers are dominated by the most mobile water fractions. In situ measurements of water content and matric suction are compared to the measured outflow. The data indicate the focusing of flow in spatially distinct areas can make in situ instrumentation a poor (non-conservative) predictor of volumetric water flow.

Jan 1, 2003

By Larkings RH

The high gas emissions associated with the depth of mining and very high coal extraction at some Australian Collieries have provided a need to investigate the influence of geological and mining conditions on levels of gassiness. The introduction of longwall extraction in particular is associated with complex strata control problems and quick changes in gassiness. To this stage of Australian coal mining, no standard method has been developed to predict the different levels of gassiness associated with the various geological and mining conditions; and the relationship between coal output and total methane make has not been established. For local conditions, with a large number of coal seams lying in close proximity to the working seam, the significant contribution of gas emissions from adjacent strata was expected, especially as strata relaxation occurred during longwall mining. This depends mainly on geological conditions, strata control and coal production. For the deepest of the B.H.P. Collieries in the Newcastle region, the relationship between coal output and total methane make has been investigated by systematic gas balance measurement during longwall extraction. The computer method of iteration was used to approximate the mathematical equation from the initial graphs of coal production versus quantity of methane in the ventilation system for various strata conditions. The angle of caving was established for local geological and mining conditions, for planning and design of the positions of cross measure boreholes.

Jan 1, 1986

The mineral sands deposit of Australia pose a number of unique, and quite unusual problems for the explorationist. Most concentrations of heavy minerals have been found in the unconsolidated sediments of the east and west coasts. Mineral sands mines open larger areas per tonne of concentrate than most other mines. This is because of the shallow depth of the sands containing the heavy mineral concentrations. Obtaining tenure can, by mining industry norms, be a massive operation due to the large areas to be examined and, particularly on the east coast, the large number of land holders encountered. A commercial development can still emanate from anything ranging from a small high grade body to a massive low grade deposit, the prices currently being obtained for rutile, zircon, ilmenite and monazite, although still modest when the remarkable properties and applications of these minerals are considered, is nevertheless attractive when compared to the prices being obtained for the base metals with the exception of gold. The current interest in the location and definition of new reserves of heavy minerals reflects this relative price attractiveness. The discovery of heavy mineral concentrates does not necessarily ensure the early establishment of a mine. Because of the cyclical nature of market prices, the average returns likely over the life of the mine permit the employment of only relatively simple, low cost, mining, concentration, and separation processes. If difficult mining conditions are encountered or the removal of small contaminants by complex metallurgical processes are required, then higher market prices must be obtained. Until the market is prepared to pay more for the commodities so produced, the resource will not be economic and lower cost reserves will be mined in preference. The Australian mineral sands industry has seen many closed mines because of past failures to properly assess the data base collected during the exploration and development phases of the failed projects.

Jan 1, 1987

The Middleback Ranges are a series of parallel northsouth ridges on the eastern side of the Eyre Peninsula, South Australia, about 20 miles inland from the Spencer Gulf, as shown in Fig. 1. They extend for some 20 miles across the centre of the County of York. North of them, on the same line of strike, in, the County of Manchester, is a disconnected series of lesser which ends in the Iron Monarch-Iron Knob ridge, the principal iron ore locality. These ridges are referred to in the following pages as an integral part of the Middleback Ranges.The deposits of hematite which outcrop in these ranges (Fig. 1) form the most important group of iron ore bodies in Australia, and are exploited by the Broken Hill Proprietary Company. The largest of them is the Iron Monarch (Fig. 6) .H: The next largest are the Iron Duke, the Iron Prince and Iron Baron. The Iron Knob, Iron Duchess, the North and South Iron Knights, Iron Queen, and the small body south of it, the Kimba Lease, and the deposits in the Cook's and Ash Leases, are all smaller.Numerous small lens-like bodies of hematite occur throughout the ridges, but are not of sufficient size to be of commercial use. At present only the Iron Monarch and the Iron Prince bodies are being worked. The Iron Knob was quarried previously, but its remaining supply is held in reserve.*Published by permission of the Council for Scientific and Industrial Research.

Jan 1, 1936

In 1972 the Marra Mamba Iron Formation in the Lower Proterozoic Hamersley Iron Province of Western Australia was recognised as a stratigraphic horizon with significant potential for high grade iron ore reserves. Within the Newman area the Marra Mamba Iron Formation has been subdivided into four strati- graphic units: Lower BIF member, Middle BIF and shale member, Upper BIF member and Upper shale member - and a standard natural gamma log reference section compiled for the entire formation. The recognition of the Upper shale member as an additional unit contrasts to the previously proposed stratigraphy. Enrichment of the Marra Mamba Iron Formation to ore grade (0)8 percent calcined Fe) in the Newman area is restricted to the Upper BIF member and to a lesser extent to the Middle BIF and shale member. Typical ore from Orebody 29 is friable interbedded martite-ochreous goethite, signifi aptly different both physically and chemically from the Brockman Iron Formation ores of the Tom Price-Whaleback type. Large scale customer acceptance trials (in excess of 4 million tonnes) have shown that Marra Mamba ore crushed to fines and blended with Mt. Whaleback fines in a ratio of up to 15:85 forms an acceptable sinter feed.

Jan 1, 1981

By D B, M A. Sares, D W. Coulter, D C. Peters

This presentation discusses NASA-funded research on the ability of hyperspectral remote sensing to map diagnostic acid rock drainage (ARD) mineralogy that adversely affects water quality within watershed and to determine the relative contributions of natural ARD sources of metals and acidity to that drainage. Ground-based reflectance spectroscopy, combined with water chemistry, is used to identify mineralogical and chemical variations throughout a watershed. Integrated with hyperspectral data acquired from airborne remote sensing platforms, such as the NASA Airborne Visible Infrared Imaging Spectrometer (AVIRIS) sensor, a methodology has been developed that should improve environmental assessments and tracking of impacts on and from drainages. Phase I of this project focuses on a drainage basin (Lake Creek), tributary to the upper Arkansas River in central Colorado, which is impacted by natural acid rock drainage from areas of high-sulfide hydrothermal alteration. This project builds upon research and inventory efforts by the Colorado Geological Survey (CGS) to identify hydrothermal alteration that is the primary source or is contributing to acidic and toxic drainage in Colorado. This presentation will cover ground and airborne hyperspectral remote sensing techniques and results and water analyses for seasonal high-flow and low-flow conditions in Lake Creek. Identifying correlations between mineralogy, especially mineralogy that can be identified through airborne remote sensing, and water chemistry is a key focus of this project. Of particular interest are low-pH iron phases such as jarosite, ferrihydrite, schwertmannite, copiapite, and transitional amorphous phases as well as AlOH phases from higher, although still acidic, pH environments which are observed to mix with the iron precipitates within the streams draining from the hydrothermal systems. Drainage in the Lake Creek watershed derives from the Grizzly Peak caldera (Oligocene), which exhibits extensive hydrothermal alteration. Alteration types include silicic, quartz-sericite, quartz-sericite-pyrite, advanced argillic, and argillic. By understanding the chemistry of a naturally impacted drainage and its relationship to the surrounding geology, the project goal is to allow more efficient and complete identification of such sources in mineralised terranes through remote sensing technology.

Jan 1, 2003

By L Reynolds

The portable infrared mineral analyser (PIMA) was trialled to determine the extent and intensity of any hydrothermal alteration halo associated with gold mineralisation in the Hyde-Macraes Shear Zone (HMSZ) of the Otago Schist.   Twelve diamond drillholes through the HMSZ were analysed with the PIMA at a sample spacing of 1 m. The drillholes were selected on two traverses along the line of strike and down-dip of the mineralisation in and around Panel 2 of the Frasers underground development.   The study showed that the Hangingwall shear of the HMSZ has a more distinctive infrared signature in intersections with high grades. The Hangingwall shear in these drill holes is defined by a shift in the wavelength of the Al-OH absorption feature from ~2220 nm to <2210 nm. This shift is attributed to a change in the mineralogy from phengite to muscovite. Overprinting this trend in some of the drillholes is the presence of the 2210 nm Al-OH absorption feature, ascribed to kaolinite. Kaolinite also tends to be present in numerous other regions of the schist above the Hangingwall shear associated with steeply dipping faults and foliation parallel joints. In drill holes with low grades the Hangingwall shear does not exhibit any obvious infrared signature.   At the scale of study, the PIMA does not provide evidence for an alteration halo associated with hydrothermal mineralisation above the Hangingwall shear. Possible tectonic movement may have displaced any alteration halo that once existed, away from the zone of mineralisation. For this reason, PIMA apparently cannot be used for predicting the location of the Hangingwall shear during exploration drilling. However, the study did show that the PIMA could define the Hangingwall shear when the rocks were sufficiently altered and mineralised.

Jan 1, 2007

By I R. F MacCulloch, K Jones

Pintail Systems, Inc, a Colorado USA based company has developed and commercially applied bioremediation processes for biological detoxification of cyanide compounds in mine waste. Site-specific microorganisms are isolated from spent ore, tailings or process solutions and augmented in the laboratory for cyanide oxidation, denitrification and metal biomineralisation. Biological processes typically treat complex contaminants (cyanide compounds, soluble metals and nitrates) in a fraction of the time of conventional remediation processes. Cyanide is used in microbial metabolic processes as a carbon or a nitrogen source. Biological detoxification processes applied at the end of mine life can end long-term liability and perpetual monitoring and containment. Case studies from commercial application and demonstration programs for the US Environmental Protection Agency will be presented in this paper.

Jan 1, 2004

By J I Stewart

The Copper Canyon deposits, occur in proximity to the regionally distinctive formational boundary between the Staveley Formation and Marimo Shale. The mineralisation here is associated with breccias, veins, and alteration zones near the base of the Marimo Shale unit and in the underlying evaporitic dolomite-dololutite dominant Staveley Formation. The Marimo Shale unit, in its basal 60 metres, is highly carbonaceous and hosts ubiquitous but minor diagenetic (?) copper-pyrite, and on occasion, extensive albite-microcline alteration centres, pyritic (cobaltiferous)-quartz veins, and microcline-quartz_+plagioclase veins or veinlet arrays. The most significant mineralisation, such as at the Greenrnount prospect, consists of a shallowly dipping package of alteration zones overprinted by multiple generations of pink-orange microcline-quartz-chalcopyrite-pyrite-(arsenopyrite) and albite-calcite- phlogopite veins. Accessory mineralogies in most of these mineralisation styles consist of tourmaline, monazite, rutile, and apatite. Chalcopyrite (and secondary chalcocite) and gold are associated with each generation of alteration but are best developed in the later stages of veining. In the underlying Staveley Formation, which is a conformable transition between the Corella Formation limestones and the Marimo Shale, chalcopyrite (cobaltiferous)-pyrite mineralisation occurs as disseminations in pre- and syntectonic breccias, and with disaggregated silica pseudomorphs (after thinly bedded evaporitic sulphate beds) and associated dolomitised limestone-calcilutite. Although this mineralisation may be partly diagenetic in origin the 200 in thick evaporitic packages are also host to a locally widespread (2 to 4 km long and 200 to >500 metres wide) and pervasive 'redrock' styled microcline-dolomite¦hematite alteration. Within this gross alteration package there also seems to be a consistent association with narrow (10 to 100 metres wide), linear (stratabound) semi-massive magnetite-hematite-microcline and quartz-chalcedony replacement zones. Like much of the nearby Corella Formation the Staveley Formation, under the Marimo Shale, has undergone dissolution, paleo-solution karsting (breccias) and tectonic brecciation such that the precursor lithological details have been progressively obliterated. The post-diagenetic to post-tectonic fluid pathway development and metasomatic alteration history of this important lithostructural package of rocks has been traced from preliminary studies only. The ability to do so is largely due to the absence of significant regional and contact metamorphic overprinting, and the local preservation of precursor sediment profiles. It is proposed that both the base of the Marimo Shale and parts of the underlying evaporitic-limestone-dololutite have acted as conformable fluid pathways for hydrothermal and (perhaps) diagenetically derived, Cu-Au-(¦Co ¦As) K-Na-Ti-REE bearing, fluids and brines.

Jan 1, 1994

By N LaBranche

The resurgence of Silicosis and Coal Worker’s Pneumoconiosis (CWP) in coalmines has placed the spotlight back on the management of worker exposure to particulate matter across all mining sectors (Coal Workers Pneumoconiosis Select Committee, 2017). There already exists a substantial body of knowledge on particulate matter and its impacts upon human health (National Academies of Sciences, Engineering, and Medicine, 2018). The contribution of silica to respiratory disease is well known and there is a growing concern for exposure to diesel particulate matter. However, it is also clear that there are major gaps in our understanding. In part, those gaps relate to the contribution to adverse health effects of mineralogical constituents in the dust (LaBranche et al, 2021a). It is also becoming evident that the size and shape of the particulate matter can affect its potential impact on human health.The University of Queensland has developed a methodology for characterising respirable and inhalable dust samples using scanning electron microscopy. Multiple samples from numerous mining operations have already been analysed using the UQ methodology. The process has been successful in showing the variety of mineralogica lcomponents and particle size distributions presentin various areas of the mines.

Oct 12, 2022