Search Documents

The Golden Cross mine is situated in a sensitive environmental setting on the North Island of New Zealand, about 150 kilometres south-east of Auckland and about 8 kilometres NW of Waihi. The mine is situated in dipping topography, with volcanic ashes making up soils, fault zones running through the area, and rainfall of about 3m per year on average. Water management is the most demanding environmental challenge on site, and a comprehensive programme has been put in place to address tailings deposition, long term tailings storage, and water treatment during and after operations.

Jan 1, 1995

During the last two decades, restrictions on access to land for mineral exploration and development in Australia have intensified. State and Federal legislation relating to Aboriginal land rights, national parks, marine parks, wilderness areas and other conservation areas, the surface rights of farmers in New South Wales and Western Australia, national, State and world heritage, urban developments and acquisition of land by governments for other purposes have all placed limits on mineral exploration and mine development activity. More than 20% of Australia's land area is now either unavailable for mineral exploration or available only under severe constraints. Access to this land is denied at a significant economic cost to the Australian community. There have been few attempts to quantify this cost. More importantly these restrictions have developed on an ad hoc basis promoted by single interest government departments often with little regard for rational land use planning. The mining industry has embraced the community's conservation ethic and accepted that conservation areas should be set aside and that within those areas mineral activity should be restricted. In some cases the restrictions on exploration near areas of outstanding scientific, historical, archeological or scenic importance may amount to an effective prohibition. The industry has vigorously opposed the exclusion of mineral activity in conservation areas on purely emotive grounds, unsupported by scientific evidence and in disregard of land use potential, consideration of multiple use potential or consultation with existing or potential land users likely to be effected.

Jan 1, 1987

By G V. R Goodman, G J. Chekan, J M. Listak

The extraction and transport of coal from underground coal mines can result in significant liberation of coal and/or silica dust into the mine atmosphere. Mine operators have long used ventilating air as a primary means of diluting generated dust, removing dust from the working faces and preventing dust from reaching the minersÆ working environment. As production levels have increased, mine operators continue to be challenged in maintaining dust concentrations below compliance levels. The need for maximising the effectiveness of available ventilating air in conjunction with other effective controls, such as water sprays and dust collectors, continues to be critical to the long-term health of mine workers. The National Institute for Occupational Safety and Health (NIOSH) has conducted full-scale laboratory and mine-site research to evaluate improved application of dust controls for both longwall and continuous mining methods. A summary of recent research results and recommended practices will be provided.

Jan 1, 2005

The Department of Mineral Resources is the lead agency in mine site environment management and control in New South Wales. The Department introduced a Mining, Rehabilitation and Environmental Management Plan (MREMP) process several years ago in order to integrate the activities of other government agencies who may have a material interest at the mine site. The MREMP process has resulted in a spirit of trust and co-operation between agencies and between agencies and mining companies. The spirit of co-operation has been reflected in greater public confidence that mining is environmentally responsible.

Jan 1, 1995

The Jundee gold mining operation is located in the Western Australian Yandal Greenstone belt. Jundee is a mature operation encompassing multiple and complex underground ore resources, dwindling open pit reserves, large surface stockpiles, small satellite resources and two near-mine but stand alone process plants. The imminent completion of continuous open pit mining and the associated drop-off in total mill feed precipitated a review of the strategic mine plan and development of options that would optimise the exploitation of the remaining mineral resources and the utilisation of the existing plant and infrastructure.An initial review of the strategic decisions to be made, available options as well as the quantity, complexity and co-dependency of the strategic variables quickly led to the conclusion that an Operations Research style modelling approach would be appropriate. An 'off-the-shelf' program engine by the name of WHATSBEST! (LINDO Systems Inc.) was chosen on the basis of price, reputation and ease of use. The model was formulated with the unknown variables (being the ore mining rates) expressed as a proportion of the maximum achievable ore mining rate from each source. Costs were defined as variable or fixed, with this definition being a key aspect of the modelling process. The critical application of the model was in determining the optimal extraction rate of ore, the destination (ie Jundee or Nimary mill) and the sequence of extraction of each ore source that maximized the cash flow of the operation. The program was designed to be able to quickly derive an optimal result from the many variables, replacing the previous laborious iterative process of arriving at an acceptable answer by means of several large and static spreadsheet models. This paper presents the process of selection, formulation, application and scope of operation of the turn-key linear and non-linear program strategic model now used as part of the Jundee Operation strategic decision making process.

Jan 1, 2002

By F Pavloudakis

The installation of on-line analysis systems in the open-pit mines of the Public Power Corporation SA (PPC, the state-owned electricity entity of Greece) is considered to be the key-parameter for performing improved quality control and blending/homogenisation of the produced lignite. In order to investigate the accuracy of these systems under the site-specific conditions of the Greek lignite deposits, a research project was carried out. This was necessary since there is lack of experience in using on-line analysers in mines that produce a fuel of such a poor and largely fluctuating quality. After thorough market research, a dual energy gamma ray transmission on-line ash analyser was installed in Kardia mine of Ptolemais û Amynteon Lignite Centre, which is located in West Macedonia, Greece. The initial results obtained after the realisation of a series of dual-comparison trials (ie using two series of reference values that allow three-way comparisons) pointed out several problems that obstacle the achievement of high accuracy on-line measurements. More specifically, the measurements obtained by the analyser were higher than the concentrations determined by the two laboratories when the ash content was lower than 12 per cent (in wet basis). On the contrary, when the ash content was higher than 12 per cent, the measurements of the on-line analyser were lower than the concentrations determined by the laboratories. In other words, the range of the measurements obtained by the analyser was narrower than that corresponding to the lab analyses results. Therefore, the use of this on-line analysis system under the site-specific operating conditions of Kardia mine does not guarantee improved quality control of the lignite fed to the mine-mouth located power plant. Most probable reasons that explain the above-mentioned problems are the following: The frequent and widely ranging fluctuations of the chemical and mineralogical composition of the lignite transported by the conveyor belt, especially as far as its calcium content is concerned. This result from the nature and the origin of the mineral matter co-excavated with the lignite, which varies from calcareous marls to sands and clays rich in aluminium and silica minerals. The fluctuations of the lignite quantity transported by the conveyor belt. The change of the linear concentration of iron contained in the fabric of different belt parts.

Jan 1, 2003

The paper briefly discusses the benefits to proponents of a formal environmental assessment process. It is argued that any process should be fair, cost effective and efficient, involve all affected parties, and should identify important issues at an early stage. The paper outlines the procedure used in Victoria, and the ways in which it attempts to address the above criteria.In conclusion the paper discusses progress towards a national approach to Environmental Impact Assessment. This is currently being pursued by the Australian and New Zealand Environment and Conservation Council.

Jan 1, 1992

BHP-Utah Coal Limited operates 33 draglines of varying sizes in the Bowen Basin of Central Queensland. The group's operations with draglines commenced in 1963 with the establishment of opencut operations at the then TPM Moura Mine and continued through expansion of that mine, the commissioning of the Utah Development Company Blackwater Mine in 1968, and the subsequent establishment of six (6) other large opencut mines, all in the general area over the next fourteen years. These operations generally commenced with boxcuts on the sub-crop at depths of 15 to 25 metres. Over the years, depths have increased so that average depths now are in the 45 to 50m range. It was soon realised that dragline operations would have to be supplemented with additional stripping equipment. In 1981, a symposium "45m and Beyond" was held in Rockhampton to assess the problems associated with such "deep" stripping. Subsequently, dragline operations have continued and although addi- tional stripping capacity has been added, in many instances, draglines have been used and are being used to dig depths greater than 45m, some- times as much as 65 to 70m.

Jan 1, 1989

By S Nie, I Bergqvist, F Ouchterlony

In blasting, a few or many cracks are driven from the borehole into the rock. But what causes the cracks? The most common theory of breakage consists of two stages; first the shock wave causes radial cracks to form around the hole then the gases penetrate into the cracks, and widen them and make them longer. Another theory presented by Brinkmann suggests that the back damage is primarily controlled by shock and that the gas penetration is the mechanism controlling breakout of the burden. He did his experimental work using blasthole liners. Recent research at SveBeFo has examined this matter further. In a quarry a number of benching holes have been blasted simultaneously. In some of these holes tubular Swellex bolts were inflated and decoupled charges put inside the tubes without stemming. Other holes were identically charged but without the lining. Finally some holes were also stemmed. After blasting the cracks in the remaining rock were studied. There was no difference in crack lengths between holes charged normally (no stemming) and holes where the charges were inside the bolts. On the other hand when stemming was used, the crack lengths increased for some explosives but remained the same for an emulsion explosive. In another set up blasted granite blocks were charged in the same way as above. Then we could also measure the bore hole pressure. The pressure gauge consists of a small carbon resistor inside a steel cylinder. It is called LHM (Location-fixed Hydrodynamic Measuring Cup) and is placed at the bottom of the hole. A smaller exit hole from the bottom is drilled for the cables. The paper presents the technique and the results obtained from both the quarry blasting and the blasting of the blocks.

Jan 1, 2001

The capabilities of the three 61R and one 81R Robbins Raiseborers currently in use at Mount Isa are defined. Their applications in the development of ventilation and hoisting shafts, orepasses, escape routes, fill passes etc. are described and possible future uses of these and newer raiseborers at Mount Isa are examined. Problems associated with the use of raiseborers, together with ways of overcoming them are discussed. The impact of raiseborers on the mining operation is assessed in terms of new approaches to design and development, safety, cost and manpower efficiencies.

Jan 1, 1974

By T GRAHAM-TAYLOR

A trend towards mining more complex and economically marginal orebodies, often combined with increasingly tight product specifications, increases the number of variables which need to be considered in production scheduling. Linear programming incorporating integer constraints can be used to create production schedules which are practical as well as mathematically optimum. Factors which can be taken into account include variability in product stockpiles, targets for head or product grades, production of different material types, production from different areas, production targets for loaders, and dependencies between mining blocks. For each schedule an appropriate objective for optimisation must be chosen. Examples of objectives are: to minimise or maximise grade variation; to minimise waste movement; and to minimise movement by front end loaders. A staged approach to the implementation of computer systems based on linear programming optimisation is Proposed.

Jan 1, 1992

By A R. A Gomes

The Metropolitan Rapid Transit Authority (MRTA) Initial System Project (ISP) - Underground Structures North, UGN, is the northern section of the blue line, which is the first stage of an underground mass transport rail system of 77 km to be implemented in the central area of Bangkok, Thailand. The UGN section (Huai Kwang - Bang Sue) consists of approximately 8 km of twin single track bored tunnels, nine underground stations and some short cut and cover tunnel sections. The paper focuses on the main issues involved in the structural design of the precast concrete lining, which is the definitive structural support of the bored tunnels. It includes an overview of the site and geotechnical conditions, specific properties of precast concrete linings, ground-structure modelling, approach for the assessment of load conditions and respective sectional forces and particulars of the detailing of the reinforcement and the segment testing program.

Jan 1, 1999

Mineral resource classification is essential because it is required for public disclosure. The resources must be binned by a qualified person into measured, indicated and inferred categories using an appropriate methodology. The classification methodologies used have long been a topic of research and discussion. There are various traditional and geostatistical methods used in practice. Some are more popular than others. Because of the uniqueness of each ore deposit, it seems almost impossible to have a single industry-accepted norm for mineral resource classification. Therefore, some experts have adapted the methodologies tailored for the deposits they are working on, but many simply use the methods they and their clients understand and are comfortable with. In this paper, a new approach is presented to classify the mineral resources using a data geometry index. This index combines both traditional and geostatistical aspects of resource classification based on the data configuration around the block interpolated. It is a function of several variables such as kriging variance calculated for a block, distance from the block to the nearest sample and the average distance of all samples used to interpolate the block. Thus the approach using this index takes into account the spatial data configuration around the block being estimated, as well as the traditional distance criteria. The data geometry index and how it is calculated is explained. A case study for a gold deposit is presented to see how the classification based on this index compares to the existing methodology used in this deposit for mineral resource classification.

Sep 26, 2011

By P J. Hawke

Within the Mesa J pisolitic iron ore mine, clay is distributed unevenly throughout the deposit and often forms as pods and channels less than 10 m in width. The mine resource model, based on 50 m + 50 m spaced drilling, has been unable to accurately delineate the clay for scheduling and mining purposes. Therefore, alternative methods for mapping the clay-contaminated ore were sought. Predictive clay mapping will significantly reduce production costs at Mesa J through improved selective mining practices, more accurate scheduling, reduced wear on mining equipment and minimising the need for maintenance of haul roads and ramps. High lateral resolution electromagnetic (EM) surveying using a Geonics EM31 instrument can quickly and inexpensively delineate the extent and orientation of the clays. Preliminary results indicate that a block model based on the interpretation of the EM data can accurately predict the distribution, volume and tonnage of ore and waste material. While rip-line mapping, infill drilling, ground penetrating radar and gravity can delineate clay with various degrees of success, none were as efficient as EM31.

Jan 1, 2002

During a mineral exploration programme in an environmentally sensitive area near Mount Painter in South Australia, a helicopter was used to position, construct and service drilling rigs in order to avoid the need to create new access tracks. The drilling programme was designed to optimise the advantages of natural landforms in order to minimise the environmental impact of site construction and drilling activities. This minimisation of land disturbance reduced the required amount of rehabilitation measures to the extent where all impacts of the helicopter-supported programme had disappeared within twelve months of completion of work.

Jan 1, 1995

Wheal Gawler was Australia's first metal mine. This leader was followed by an army of other metalliferous underground mines and surface operations in Australia. As a mine it was not highly significant economically because its small total production of nearly pure galena had low multiplier effects on the economy of South Aus- tralia. Its importance lay in its symbolism: here was a silver-lead mine close to the new town of Adelaide posing the question of what other min- erals lay in the Mount Lofty ranges and in the fields beyond.

Jan 1, 1987

By D Fargher

BHP BillitonÆs Cannington operation began production in 1997 and is presently the largest tonnage and lowest cost single mine producer of both lead and silver in the world. The original design capacity was 1.5 Mtpa and this has progressively increased via a series of debottlenecking projects in both the mining and milling operations. In 2003, 2.39 Mt of ore was mined, whilst 2.31 Mt of ore was milled. In February 2003 Cannington received approval to expand the project to a sustainable capacity of 2.4 Mtpa. This resulted in underground development into the northern zone, upgrades to the concentrator, increased accommodation at site and power station capacity. The Cannington project development team implemented a partnership approach to the project. Fraser Osborn Engineering and Outokumpu Technology worked closely together with the Cannington team to meet all of the project constraints.

Jan 1, 2004

By J-P Franzidis

A technique for determining the recovery of attached particles across the froth phase in flotation that relies on measuring the rate at which bubble-particle aggregates enter the froth is used to investigate the selectivity of attached particles across the froth phase. Combining these measurements with those of other techniques for determining the froth recovery of attached particles provides an insight into the different subprocesses of particle rejection in the froth phase. The results of experiments conducted in a 3 m3 Outokumpu tank cell show that the detachment of particles from aggregates in the froth phase occurs largely at the pulp-froth interface. In particular it is shown that the pulp-froth interface selectively detaches particles from aggregates according to their physical attributes.

Jan 1, 2005

The paper examines the difficulties encountered by objectors to mining privilege applications. It describes the various involvements of the environmental defence society in the mining controversy and makes some comment on the proposed amendments to the Mining Act 1971.

Jan 1, 1981

Milling operations at Misima Mine are discussed, with specific reference to the application of energy and cost saving concepts. Design stage innovations and post-commissioning developments are covered. General operational problems are described with specific reference to problems associated with operating in a remote location.

Jan 1, 1994