Search Documents

By Smith P

The past 20 years have seen the replacement of hydraulic control of longwall mining systems by the neater. smaller and better controlled electronic units.Early problems of moisture and other effects on reliability were overcome to see electronically controlled supports chosen for Corrimal Colliery ten years ago. Lessons from Corrimal and elsewhere, with following improvements and sophistication led to wider use as exemplified by Meco and other electronically controlled supports used in more recent installations in New South Wales, Queensland, USA and Czechoslovakia of the total of over 80 electronically controlled support installations worldwide in the past decade. Present work is toward a fully "integrated face" of British Coal by 1993, incorporating the Meco automatic face straightening system already due for practical use in the UK later this year. However the manless face still appears to be some way off although the present minimum crews and close monitoring, including early warning, are promising stages.

Jan 1, 1991

QEMSCAN« technology is a widely accepted automated e-beam technique providing quantitative and statistically robust mineralogical data to the mining industry. It uses X-ray mapping combined with backscattered electron (BSE) brightness to identify minerals in almost any type of geological material (Gottlieb et al, 2000). Besides the modal mineralogy also the liberation, associations, average grain size and other textural information can be obtained. The aim of this study is to test reproducibility of this technique by setting up and running standard tests on different QEMSCAN« systems. Multiple sample blocks were prepared by our standard operating procedure as epoxy-mounted, carbon-coated, polished blocks. The replicates were measured under the same conditions and measurement parameter settings on different QEMSCAN« instruments. The relative standard deviation (RSD) for the set of measurements was calculated. Generally the reproducibility of the systems themselves was found to be excellent, ranging between 0.4 and 1.5 per cent RSD. The more significant change in the reproducibility was found to be caused potentially by the sample preparation and variation in the mineralogy of the replicates. The measurement parameter settings together with these variations can account for almost 15 per cent RSD for minerals of low abundance. For analysed samples good results for the main phases present in quantities higher than 2 - 5 wt per cent of the total mass of the sample were confirmed with RSD generally below six per cent. Following the experiments, the parameters having the biggest influence on the performance of the QEMSCAN« and its precision are discussed in detail. The importance of sample preparation procedures and measurement parameter settings is emphasised. It is shown that experience and excellence is necessary for getting the most from the automatic mineralogical methods like QEMSCAN«.

Jan 1, 2008

This paper intends to give an insight into what is often considered to be a poor relation of the mining industry but is in fact an integral part of any community. Aggregate production accounts for more than half of the world production of minerals by weight. In New Zealand production of aggregates runs at around five tonnes per capita per year, making it a significant industry. The industry in this country is dominated by smaller operations close to the market due to the widespread population and relative abundance of aggregate. The Logan Point quarry is one of the largest quarries in the South Island with an annual production of around 250 000 tonnes. The market is mainly based around roading and building in the Dunedin area with some higher quality specialist aggregates being used allover Otago. The quarry has been owned and operated by Palmer and Son Ltd for 106 years with a fifth generation family member the current quarry manager.

Jan 1, 1992

By Manula C. B

The total systems model for underground oal mining planning and design is a set of omputer programs which encompasses a realis- ic reproduction of the interaction between he geological, environmental, equipment, meth- ds and the health and safety aspects of the ining plan. The total system includes nine ajor subsystems - Geology and Reserves, Meth- ne Generator, Roof Support, Subsidence, Pro- uction, Rail Haulage, Cost, Water Generator, nd Ventilation. The subsystems themselves re divided into two categories based on the requency with which they are executed. Event riented Subsystems are executed either inde- endently, or at discrete intervals when cer- tain specific events occur. Dynamic subsystems 'unction interactively during the production :ycle. They transfer data to or request data `rom event oriented subsystems only when spe- ific events occur. Three specific areas for iodel application are in the measurement of system performance, the development of the '_ nterrelationships of the components of deep Wining process and the evaluation of new and Lnnovative mining technology.

Jan 1, 1977

Process mineralogy is an inter-discipline in the fields of mineralogy and mineral processing. As a predicting and trouble-shooting tool, process mineralogy helps address all mineralogical issues and problems related to mineral processing. It provides useful information on process design and optimisation, flow sheet development and cost reduction. As more and more complex and refractory ores are being discovered and processed, it is believed that process mineralogy will gain more attention and play a more important role in process design and optimisation. This paper will first discuss the scope of process mineralogy and mineralogical factors that may affect mineral processing of various ores, and then focuses on the application of process mineralogy in process design and optimisation through case studies.

Jan 1, 2008

By R Butler

Contract m1n1ng in New Zealand developed in the coal industry and has become an element in the success of recently opened hard rock gold mines. At Martha Hill, the mining contractor is undertaking a wide range of activities from open pit mining, crushing, conveying, waste embankment construction and drainage.

Jan 1, 1991

The outcome of future metallogenic research will be important to everyone because it will. have a profound impact on our ability to find new deposits of non-reservable mineral resources. Failure to replenish our mineral stocks will threaten man's economic and social well-being, and it is vital that future directions of metallogenic research are considered carefully to ensure that research funds are applied wisely to underwrite our future.Today we are witnessing the declining phase of the era of easy exploration. The rate of discovery of shallow orebodies is slowing. This is very evident for base-metal deposits but is becoming increasingly apparent for gold deposits. The easy exploration era was marked by a heavy reliance on exploration techniques capable of directly detecting mineralization. These include simple prospecting methods as well as a host of geochemical and geophysical procedures and tools that enable explorers to pin-point regions' of mineralization within the upper couple of hundred metres of the Earth's crust. The role of

Jan 1, 1990

Late Palaeozoic and Late Mesozoic phases of widespread overprinting have obliterated most of the primary magnetization signature of the Tasman Fold Belt. Palaeomagnetic programs of a regional extent offer best prospects for identification and interpretation of such secondary magnetizations and for isolation of any remaining primary magnetization. In 1983 the BMR initiated a regionally oriented palaeomagnetic study of the Tasman Fold Belt to obtain palaeomagnetic constraints on the tectogenesis of the fold belt. Particular attention is being paid to the analysis of possible differential movements between suspect or- tectonostratigraphic terranes within the Tasman Fold Belt and the respect to cratonic Australia. Work has concentrated so far on the Cowra Trough-Molong High region of the Lachlan Fold Belt and the New England region. Pilot sampling has been carried out in the Gympie region. In addition Palaeozoic sequences are being studied from the Amadeus Basin and the Ngalia Basin to refine the palaeomagnetic reference frame of cratonic Australia.

Jan 1, 1987

By R Bresca, A McCallum, J Scealy

The Endeavor Mine, located to the north of Cobar, New South Wales, was purchased by CBH Resources Pty Ltd in September 2003. The operation has been producing lead and zinc concentrate continuously for over twenty-three years. In 2004, a water management program was instigated to improve the raw water use efficiency of the mining operation. The water management program involved the establishment of a Water Management Committee, a review and quantification of water use across the site, investigation and implementation of efficient water use practices, and workforce awareness training. The program has seen the amount of water used per tonne of ore milled reduced from an average of 1.08 kL/t in the March 2004 quarter, to 0.68 kL/t in the March 2005 quarter. This paper outlines the Endeavor Mine water management program and may serve as a model for other operations that are planning to improve their water use efficiency.

Jan 1, 2006

The A J Parker Cooperative Research Centre for Hydrometallurgy has recently been established by a major grant from the Australian Commonwealth Government. The participating institutions in this centre are the CSIRO Division of Mineral Products, Curtin University of Technology, Murdoch University and the Chemistry Centre (WA). The Australian Mineral Industries Research Association is also a partner. Information is presented about the research activities of the Parker Centre, which are focussed on the solid/solution interface. Three research programs have been established in the areas of leaching, precipitation and surface processes (adsorption). The initial projects within these three programs are described. Details are also given of the Centre's education program which include honours degree training, masters and doctoral degrees by research, a masters degree by course work and workshops. The importance of collaboration with industry to the successful operation of the centre is stressed.

Jan 1, 1992

By B P. Banerjee, D Patra, S Raval

Roof bolts are an essential component of roof support systems in underground mines. They are used to provide structural support to the roof of the mine and prevent it from collapsing. Therefore, it is imperative to perform regular assessments of these roof bolts to avert any hazards. Manual investigations of roof bolts are done by surveyors in underground mines, which is extremely timeconsuming and challenging due to the low-light conditions in underground mines accompanied by stringent mine access rules. To this end, automated recognition of roof bolts in 3D point cloud data obtained through laser scanning in underground mines serves as a potential solution to aid roof bolt monitoring. With the continuous advancements in laser scanning-based 3D data acquisition systems, the feasibility of making such surface estimations from 3D point cloud data has increased severalfold.

Sep 1, 2024

By P A. Grossman, J H. Rubinstein, M Brazil, D Whittle

Many ore reserves are harvested by a combination of open pit and underground mining methods. In these cases, there is often material that could be mined by either method, and a choice has to be made. The area containing this material is referred to as the transition zone. Deciding where to finish the open pit and start the underground mine is referred to as the transition problem and it has received some attention in the literature since the 1980s.In this paper, we provide a review of existing approaches to the transition problem encompassing: graph theory-based optimisation employing an opportunity cost approach, heuristics and integer programming. We also present a novel opportunity cost approach, that takes into account a crown pillar, and show how the new approach can be best applied through the unconventional application of an existing mine optimisation tool.CITATION:Whittle, D, Brazil, M, Grossman, P A, Rubinstein, J H and Thomas, D A, 2016. Determining the open pit to underground transition – a new method, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 731–742 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By B Harvey

Achieving community and stakeholder endorsement during life-of-mine planning and implementation requires a business-connected approach, as opposed to charitable giving, disconnected offsets and environmental adventurism.CITATION:Harvey, B, 2014. Extractive companies, development and environmental agendas, in Proceedings Life-of-Mine 2014 , pp 19–22 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By J M. Parr, C J. Yeats

Discovered in 1991 by combined plume detection and bottom-tow photography (Binns and Scott, 1993) and for some years thereafter the highest tenor mineral occurrence known on the ocean floor, the PACMANUS hydrothermal field has since been surveyed and sampled in great detail by CSIRO and international research agencies (Binns et al, 1995; Auzende, Urabe and Scientific Party, 1996; Binns et al, 2002; Tivey et al, 2006). Since 2005 commercial surveys employing deep-tow geophysical packages and remotely-operated vehicles (ROVs) have been conducted by Nautilus Minerals Inc and partners within Papua New Guinea-granted offshore exploration licenses (Nautilus Minerals Inc, 2008). Two academic drilling programs have been conducted, one under the international Ocean Drilling Program (ODP) directed at deep structure (Shipboard Scientific Party, 2002; Binns, Barriga and Miller, 2007), and one using a 5 m capable seafloor diamond drill to investigate the immediate subsurface at one site (Petersen et al, 2005). An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By N Maistry, A Singh

It is estimated that in less than a decade, high-grade iron ore reserves in South Africa will be depleted, leaving only low-grade ores with a dominant lithology of banded iron formation (BIF) hematite. BIF is a complex ore reserve as it is typically liberated below 1 mm, resulting in high energy costs. However, due to its abundance, its beneficiation potential should be evaluated to maximise recovery at an acceptable product grade. To develop a beneficiation program for BIF hematite, the first step is to determine the effect of two laboratory crushing techniques on mineralogical characteristics, specifically liberation and shape. For this study, the cone crusher and high pressure grinding rolls (HPGR) were used. The Electron MicroProbe Analysis (EMPA) and Mineral Liberation Analyser (MLA) were used to compare the mineralogical characteristics. The liberation characteristics for hematite are similar for both crushing techniques; however, HPGR preferentially liberates quartz. HPGR achieved 8– 12 per cent additional quartz liberation in the greater than 80 per cent and 100 per cent liberation classes respectively and specifically in +75 μm size range. Improved quartz liberation is associated with lower energy requirements for downstream milling and improved separation efficiencies for beneficiation units that operate in this size range. Both samples displayed similar shape characteristics; most particles were elongated smooth and the rest were elongated angular. Good hematite liberation is expected at grinds of 212 μm to 150 μm. Further consideration should be given to throughputs, energy efficiency and downstream equipment selection prior to selecting a crushing technique.

Sep 18, 2023

Comparison of the Zadra, Anglo-American and organic solvent procedures for desorption of gold from activated carbon loaded in carbon-in-pulp gold circuits indicates that the Anglo American and the organic solvent procedures are considerably more effective than the commonly used Zadra procedure. Organic solvent elution procedures, particularly those using acetonitrile and acetone, can provide effective gold elution and very high concentrations of gold in eluate solutions. The operational simplicity and effectiveness of the Anglo American procedure would appear to make it the most satisfactory procedure available at the present time but this may change as the solvent elution procedures become better developed. INTRODUCTION The carbon-in-pulp technique has been introduced into the gold processing industry to by-pass the often lengthy CCD and filtration steps required in the conventional Merrill Crowe cyanidation procedure for gold recovery. Adsorption of gold on to carbon is also a valuable technique for recovering trace amounts of gold from low level waste streams from conventional processing procedures.

Jan 1, 1982

By P McGavin, R von Varendorff

With the economic trend towards reduced capital spend, more stakeholders are focusing on improved operational efficiency and productivity. Advancements in achieving the optimum dollar-per-tonnage will be more dependent on creating a logistics system that is well balanced and economically optimised. Critical to predicting a successful business case is the ability to accurately define capacity, realistically increase throughput and proactively translate objectives into design and operating requirements. Failure to do this will create an unrealistic perception of capacity and performance for the export corridor. This transition requires a fundamental understanding of the drivers that impact capacity, cost and value across the entire logistics chain. Through examples, this paper will identify the contextual requirements for simulation models that assist decision-makers and stakeholders to more clearly understand the implications of decisions that will define capacity and operational performance. The aim of this approach is to provide a rigorous analysis of the outcomes - regardless of whether the export corridor is owned, used and operated by one entity or various companies.CITATION:von Varendorff, R and McGavin, P, 2013. Can we live up to the capacity expectations weÆre predicting for our iron ore export corridors?, in Proceedings Iron Ore 2013 , pp 553-560 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By G Cormack

By designing comminution circuits for mineral liberation rather than the final recovery process and by using high mass pull gravity recovery, the concept of underground processing has become a reality. Gekko has found that many ores respond favourably to fine crushing with either high pressure grinding rolls or vertical shaft impactors which when combined with the InLine Pressure Jig gravity separator and coarse flotation results in a narrow, low-head, compact processing plant that can be sensibly fitted in existing underground openings. The focus on fine crushing reduces the power requirements of the plant to approximately 5 kWh/t for a capacity of up to 20 t/h run of mine ore feed. The use of water recycle systems places no extra load on the mineÆs normal water handling system. GekkoÆs underground processing plant, the æPythonÆ, has been designed to be towed down the decline or lowered down a shaft and is capable of being installed in sloping, non-linear drives for placement close to the working face. The overall benefit to mining companies of this concept has been estimated to be a significant operating cost-saving, lower cut-off grade and a significantly smaller environmental footprint.

Jan 1, 2008

By Kukla G. T

A Seam deposit User oriented Mine Planning System (SUMPS) was developed by The Broken Hill Proprietary Company Limited (BHP) at its head office in Melbourne. It is one of the computer mine planning systems developed by the Corporate Data Processing (CDP) section of BHP. To date it has been employed in the feasibility study of four coal prospects for the BHP Group, including Gregory in central Queensland - Ham and Van Hoorn (1978). It was also used in detailed short term mine planning for Gregory. A recent application was in the feasibility study of Saxonvale, a multi seam coal deposit in New South Wales with seams up to 20 m thick. The other two applications of SUMPS were also on thick multi seam coal deposits. Development of programs for the underground sub-section of SUMPS is continuing. SUMPS was developed and implemented on mini computers with graphics and plotting peripherals. The company's philosophy towards computing is one of centralized development and project planning, with transfer of hardware and software to site once the mine becomes Operational.

Jan 1, 1980

By I Thin, I Sheppard

Resin encapsulated rock bolting practices have been adopted by Mount Isa Mines since the early-1980s. Fully encapsulated rock bolt systems meet designated requirements for long-term ground support in the mines. A variety of rock bolts, resins and installation methods have been utilised over this period in underground mining. As a parallel to this evolving application, Mount Isa Mines have tested various resin encapsulated rock bolt systems. Testing has included routine underground pull testing and the development and implementation of the push test for the entire encapsulated bolt length. The latter test enables a greater understanding and representation to be had of the overall mixing, level of encapsulation and capacity of the system. Rock mechanics at Mount Isa Mines undertake evaluation of new bolt systems that become available, in addition to the maintenance of compliance with quality control measures for the existing systems. Improved methods of installation and systems are also investigated to further the cost-effective nature and minimise risks associated with resin rock bolt practices.

Jan 1, 2002