Search Documents

There are significant Mineral Resource and Reserve reporting challenges facing a mining company operating in the global arena. This paper specifically examines the Mineral Resource and Reserve reporting challenge facing BHP Billiton. The changing regulatory environment creates a significant challenge for global mining companies when reporting Mineral Resources and Reserves. The development and implementation of internal policies and standards for collecting and collating resource and reserve information is required for corporate governance, however the challenge is then to report this information publicly in such a way as to comply with the various codes and requirements in the many jurisdictions in which the company is required to report. The move to an International Code is not only desirable but is an essential requirement in todayÆs global market. The agreement to report using a single code internationally is however only the first step. A truly practical international reporting system must have common definitions and guidelines for interpretation as well as an international approach to the definition of a Competent Person, and even more importantly a common acceptance of that code by the relevant investment regulatory bodies. Without the universal acceptance of the concept of an international reporting code by the major regulatory bodies, implementation of such a code will be limited. With the major global mining companies seeking to raise capital in the USA, the worldÆs largest capital market, the Securities and Exchange Commission (SEC) and its approach to reserve reporting is becoming increasingly important. The development and implementation of an International Code must gain the support and acceptance of the SEC if it is to be successful.

Jan 1, 2002

Potential hlghwaJl mining reserves in Australia are large, but geotechnical and operating conditions are quite different from those where highwall mining has evolved in the USA. In order to achieve safe and effective resource recovery, equipment and procedures should be developed to penetrate 250 m in the Australian mining environment. This paper identifies key auributes to be incorporated in such machinery and methodology. These suggestions are intended to promote discussion on innovations to satisfy Australian requirements for highly productive, safe and environmentally acceptable techniques.

Jan 1, 1993

The effects of process variables such as solution chemistry, flocculent type and dosage, intensity and duration of mixing, and solids type and concentration, on the performance of flocculation/clarification/thickening processes are described. System response is evaluated in terms of the specific effects on floc settling, supernatant clarity and sediment compressibility. The implications of these results with respect to industrial practice are discussed and general guidelines for direct application to plant design and operation are suggested.

Jan 1, 1993

By A Gibbs

Culture and leadership go hand in hand, especially when it comes to investing in safety. But the reality is that most safety leaders haven’t been taught the fundamental soft skills needed to lead effectively. In fact, only one in four safety leaders demonstrate effective skills and behaviours. Furthermore, when compared to its peers in other high-risk industries, our research indicates mining has the most room for improvement when it comes to effective safety leadership. In this presentation safety culture, climate and leadership will be outlined. Additionally, research data collected from our clients, across a variety of industries, will be shared to inspire reflection on the value of safety leadership. Finally, strategies to empower leaders and increase safety leadership behaviours will be described.

May 5, 2022

The behavior of a curved wall under earth pressures for a horseshoe shaped tunnel lining is considered to be closely related to the beha vior of a vertical beam with variable flexural sti-"ness on an elastic foundation. In stress analysis an approximate method which divides the axis of the tunnel lining into small finite lengths and replaces the integrals by summation is usually adopted. this method is extremely complicated and tedious. However the variations of the moment of inertia from point to point along the wall axis can be expressed by a power function inversely .eith the distance from the ll )ottom and the analytical method can still used. The equations for the calculation of deflection, rotation, bending moment, shearing urce, and soil reaction of the curved wall are derived in nondimensional forms in this paper.

Jan 1, 1987

By Butler RD

The Singhbhum Copper Belt is an arcuate zone of verthrusting which extends over a strike length of about 180 kilometres, located in Eastern India, 150-300 kilometres west of Calcutta. The Belt is noted for its mineralisation, and both copper and uranium are currently being mined within it.

Jan 1, 1990

By Kwok S, Haemmerle A

Treatment methods for a low grade deposit at Mt. Fitch near Rum Jungle, N.T., were investigated. Physical beneficiation of the ore, sulphuric acid leaching, carbonate leaching and various methods of uranium extraction from the leach liquor were studied. Although the deposit occurs in a carbonate environment, acid leaching of the ore after beneficiation by radiometric sorting appears to be the most economic treatment method. Uranium would be recovered from the leach liquor by solvent extraction.

Jan 1, 1970

Over the last 100 years in the Polish mining industry considerable work has been done to assess optimum slurry, develop flexible delivery systems and adjust the fill technology to a wide variety of mining and geological conditions. Sand or industrial mineral waste materials for the backfilling of underground voids are used to control ground movement and surface deformation. This paper discusses various criteria to be considered in the preparation of a fill, including slurry properties, mine infrastructure, mining geometry, placement methods and the purpose of the backfill. This paper presents laboratory and in situ test data on the influence of materials parameters on the slurry flow in a pipeline system, stiffness, permeability, binding time and strength of a backfill, on the distribution of mixture in underground voids or the penetration between roof fall materials.

Jan 1, 1998

By J Hunt

A critical aspect of geometallurgy is quantifying mineralogical and textural relationships that affect mineral processing (eg, liberation and recovery). However, to date, this has been an expensive and time consuming venture and only minimal amounts of this type of data are typically available to be included in the mine planning process. Our research is focused on developing methods that will produce the required mineralogical and textural data rapidly and inexpensively. New methods of characterising liberation potential from image analysis of coarse particulate material and direct small-scale flotation measurement are compared with measurement of liberation at final grind size (ie conventional tests on MLA). The new tests are designed to rank the liberation potential of samples in order to classify an ore deposit into domains of low, medium and high liberation potential. This parameter can then be used to adjust the cutoff used to differentiate ore from waste. Results to date show that all tests provide the same ranking for the samples. The measurement based on coarse particulate material compares favourably to the results from MLA analyses on the same samples. Further work is being carried out to determine which of the tests will be the most effective in terms of time, effort and cost

Sep 5, 2011

Working thick coal seams in Poland is a very serious problem. Nearly 40 per cent of all coal is extracted from seams more than 3 m. thick. In absolute figures this represents about 70 million tons of coal per year. Working seams with thicknesses up to 3.5 m. does not present, at present, major difficul- ties. Working thicker seams calls for a steady improvement in order to increase the degree of utilization of the deposit and to enlarge the concentration of output. The problem is sometimes more difficult because, in many cases, the seams are worked under protected surface structures which compels the mines to use hydraulic stowing with all its advantages and disadvantages. Rock burst hazard, the control of which is the basic problem hindering the mining, is a further problem. The mining systems used in Poland are adapted to these natural and technical conditions.

Jan 1, 1976

Wire rope, when used for hoisting on a mine is the weak- est and most vulnerable unit in the most expensive'-group of installations or! the mine. With the introduction' of hoisting on the S1Koepe"' sheave, a new technique was-established. This innovation brought with it the certain- advantages which long had been recognised and which are being developed further. For many years, drum winders of many types had been the sole means by which ore had been hauled from mines. This type of winder, with its capacity for rope storage on the drum, permitted mine operating personnel to cut short lengths from

Jan 1, 1964

By Li N, Grimsey E. J

A technique has been developed for the fast measurement of the liquidus temperature of molten salt systems. The method employs a type K thermocouple embedded within the centre of a copper cylinder. The cylinder is immersed into the molten salt bath and the resultant heating curve is recorded using a PC-based data logging system. Upon immersion of the cylinder into the bath, a layer of salt freezes from the melt onto the surface. When this layer remelts during heating, the shape of the heating curve exhibits a change. The onset of this change can be detected by numerical differentiation of the heating curve, and the temperature at the onset represents an estimate of the liquidus of the melt. This work describes the technique and its application to the measurement of liquidus temperatures of MgC12 - NaCl and BaC12 - NaCl salt mixtures, in addition to a number of solidus temperatures.

Jan 1, 1996

By Aziz NI, Bridgwood EW, Singh RN

One of the major impacts of using modern mechanised systems of mining is the production of large amounts of extraneous dirt intermixed with the Run of Mine output. The paper out- lines a proposed system of utilizing liquid tailings from coal mines to replace imported cementitious materials used in ground control and various other safety measures. A geotech- nical and cost assessment of the proposed system are also included. The paper concludes that it is possible to utilize processed tailings to cost effectively replace imported packing material for ground control.

Jan 1, 1986

By Cottrell EC

Remote sensing has been used for many years but until recently its application has been limited by the resolution of the data available. High resolution airborne multi-spectral scanner data (MSS) has proven suitable for a number of applications including environmental management and monitoring. A shallow water mapping research. project completed on the Gold Coast has shown that- remote sensing can be used as a cost effective tool for environmental management and Monitoring.

Jan 1, 1987

By Merritt RR

The equilibrium phase relations in the Fe- Mn-Ti-0-S system were established at 1380 and 1485 K. The elemental distributions between the equilibrium phases were obtained by chemical- ly analysing selected samples from the phase study. The results are considered in relation to the coal reduction process for upgrading ilmenite. The beneficial effect of adding sulfur to a kiln that uses a manganese-rich feed is ex- plained by the formation of a metal-sulfide solid-solution phase that removes part of the manganese from the oxide system. The optimum conditions for operating the reduction kiln are determined, and the practical need to operate the kiln at other than optimum conditions is explained. It is shown how the experimental data can be used to predict the best compromise conditions for reduction and the resultant purity of the product.

Jan 1, 1980

Chile, which hosts around 30 per cent of the worldÆs copper resources, is now the largest producer and exporter of copper. Chilean copper output accounts for more than one-quarter of total worldwide production. An increase to around 40 per cent is forecast by the end of the century. In addition, Chile ranks eighth in silver production and 11th in gold output. In Chile, mining generates more than eight per cent of the countryÆs GDP and the total value of mineral exports is more than US $7.85 billion corresponding to more than 25 per cent of South AmericaÆs mineral production. The rate of growth of Chilean mineral production is indeed impressive. Table 1 shows that in the period 1969 - 1998, copper annual production increased 564 per cent from 667 000 t to 3 764 000 t. Gold production went up 27 times from 1827 to 49 770 kg. Silver output grew 1219 per cent from 95 650 kg produced in 1969 to 1 166 380 kg in 1998. Several facts explain this dramatic increase of production, but the most important was the success of exploration sustained over the same period. This resulted in the discovery of several world-class deposits which when developed into mines, account for much of the production increases. Therefore, this summary review shows the success of basic exploration carried out during the last 30 years in the Chilean territory. The review is based on data already published in different specialised mining books or magazines. It only includes those world-class discoveries not the lesser discoveries important at local scale. All figures were calculated using 1998 $US dollar and average estimated metal prices valid for 1999: copper $US 1653 per t ($US 0.75 per pound), gold $US 9452 per kg ($US 294 per ounce) and silver $US 177 per kg ($US 5.5 per ounce).

Jan 1, 1999

Utah Development Company began prospecting for coking coal in 1961 and Blackwater Mine became a reality in June 1967. Exploratory and develop- ment drilling has been a continuing effort and reserves have been assessed at several stages. Some of the history of exploration and reserves assessment is given and practices in drilling, sampling and testing are described, particularly in regard to objectives of drilling and reserves estimation. The current methods for calculation of reserves are described and some comment is made regarding use of the data in mine blending control and plant operation including correla- tion of results.

Jan 1, 1979

By Paine GG

In coal mining each of the unit operations are interrelated with each preceding operation having an effect on subsequent operations. This presents difficulties for determining when the lowest overall costs for a particular mining system are achieved. Drilling and blasting is the first mining operation for production and is known to have an effect on the subsequent loading, hauling and crushing operations. Computer blasting models developed over the past 15 years can be used to describe the drilling and blasting operation. This paper describes the ICI Blasting Model "SABREX" in detail. Methods of using the model are discussed. This involves field measurements of geological structure, shallow refraction seismic surveys, laboratory measurements of rock properties and high speed photography of blasts. The predictions are compared with actual blast results for fragmentation sizing and muckpile profiles. Outputs from the model are described and these can be used for input to models of subsequent operations.

Jan 1, 1987

The concentrating plant of the Broken Hill South Limited was described in Proceedings No. 44, Australasian Institute Mining and Metallurgy, December, 1921, by Wainwright and Read. It was erected on the present site in 1907 and 1908.From that date, the plant has undergone various alterations consistent with metallurgical improvements. By 1925, the timber work of the gravity secti"on had seriously deteriorated, so much so, that, when the machinery was working, the floors and supports vibrated badly, causing heavy maintenance costs.In 1928, it was decided to erect a new gravity-treatment section, to be followed later by a new flotation section.

Jan 1, 1932

The paper describes the $US240 million expansion at Hudson Bay Mining and Smelting Co LimitedÆs operations in Canada. The company has been continuously producing copper and zinc from local area mines at its Flin Flon metallurgical plant since 1930. The paper details the companyÆs operational turnaround since 1995 and æThe 777 ProjectÆ which includes: two new mines, expansion and modification of the concentrators, expansion of the zinc pressure leach plant, a new zinc electrolytic cellhouse and the modifications to the copper smelter gas handling system to reduce ground level gas emissions.

Jan 1, 2000