Search Documents

By P Bartlett, K Naidoo

Premier Diamond Mine is planning a new, mechanised, block cave, with a production level approximately 1000 m below surface. A high degree of tunnel damage is expected, due to stress and the relatively low in situ strength of kimberlite. An evaluation of the timing of tunnel excavation, tunnel size and spacing has been carried out to define critical parameters for planning layouts and development schedules. Extensive use has been made of three-dimensional FLAC3D numerical models, calibrated against known rock mass behaviour at 650 m depth, to examine the influence of undercut advance on production level excavations. These were able to represent the effect of stress rotation on tunnels during undercut advance and the effect of an inclined undercut. The analysis has provided guidelines that are possibly applicable to any deep block cave layout. The choice of drawpoint layout is of considerably less significance than the proportion of ground extracted on the production level elevation prior to advancing the undercut. The analysis shows that damage to production development will be potentially severe if it is all excavated prior to advancing the undercut, or is mined directly beneath the undercut face. The development of the main production tunnels alone ahead of the undercut may be feasible, but no breakaways should be put in as they appear to trigger a rapid increase in the severity of damage. The optimal sequence is when all production tunnels are developed at least 10 m in plan behind the undercut, where the induced peak field stress is less than 20 MPa and a maximum support pressure of 100 to 500 kN/m2 is require to contain movement. The assessment showed that the conditions are not significantly improved by increasing drawpoint spacing from 15 m to 18 m. The vertical spacing between the undercut and production level beneath is investigated. Provided production level development is carried out beneath the undercut, there would appear to be little benefit in increasing the vertical spacing between the undercut and production level beyond the current 15 m to 18 m.

Jan 1, 2000

By Walker BV

Mining activity has been an integral component in the New Zealand economy since the early days of European settlement. Recently in common with other Pacific Rim countries there has been a resurgence of investment in gold. A sustained and increasing exploration effort has resulted in the rapid development of alluvial gold mining operations, a number of hard rock gold discoveries, and a general optimism about New Zealand's prospectivity. New Zealand's attitude to mining development, in particular hard rock gold mining is influenced by high environmental values and a concern, largely through absence of examples, that modern mining may not perform to community standards. While these environmental concerns are wide spread there is a growing realisation that gold mining, if properly managed, can take place within acceptable environmental standards and that it has the potential to contribute significantly to New Zealand's economy. New mining developments have an important role to play in this process. The mining industry in New Zealand is now at a crossroads. Having invested substantially and confirmed the potential for gold mining developments it has found itself in a rapidly changing economic environment as the Labour Government puts in place a number of fundamental economic reforms. The reforms are intended to free up the economy removing the rafts of subsidies and protective measures which have stultified initiative and growth. A fundamental reform of the public service has been initiated including corporatisation of trading activities and the establishment of a Department of Conservation to administer estensive areas of Crown land. Both petroleum and mining taxation are being reviewed with the intention of creating a more neutral competitive environment. Mining legislation is also being re-examined with both efficiency and equity objectives. While the current environment is characterised by uncertainty and rapid change, the outcome will be a more market-oriented stable policy environment, to the mutual benefit of the industry itself and the New Zealand Community.

Jan 1, 1987

By K J. Lownie, T Rafferty

The in situ testing of mine ventilation fan systems has been a contentious issue for many years. Site testing was generally undertaken by adapting standards that were developed for the laboratory testing of fans using standardised airways. The deficiencies inherent in this practice have been widely recognised by informed practitioners, and this led to the first stand-alone document specifically intended for the in situ testing of large fans (ISO 5802:2001 Industrial fans - Performance testing in situ).This paper describes the structure of the International Standards organisation and the processes that are followed in the course of preparing such a standard.The application of ISO 5802:2001 is briefly outlined together with how test data is assessed for compliance with the suppliers guarantee. This paper must be read in conjunction with ISO 5801:2007, ISO 5802:2001 and ISO 13348:2007.CITATION:Lownie, K J and Rafferty, T, 2013. A review of ISO 5802:2001 industrial fans - performance testing i n situ, in Proceedings The Australian Mine Ventilation Conference , pp 149-154 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By S Slusarczyk, Z Kozlowski

Vibration of surface caused by seismic quakes can make a risk to great mining costruction. We have to do with this risk in the Belchatow open cut mine where seismic quakes of various energy and range have occured since the end of 1970s. The seismic risk influence on the mine structure with the special attention to the slopes of an internal dump has been presented. Hydrogeological and geotechnical conditions of the lignite mining and internal dumping of overburden and ash from Belchatow power plant have been considered. Seismic activity in Belchatow open cut from 1979 to 2001 was described and the connection between mine working and seismicity of this area was investigated. The energy and approximate location of the quakes and seismological parameters of the strongest ones observed from 1995 to 2001 were presented. The mechanism of the quake focuses was determined by means of the primary-arriving wave method. Stability of the slopes was evaluated by means of the Fellenius method. It has been found that seismic events occured in Belchatow region may cause only local eboulements whereas there are not any safety risks to the stability of slopes of the internal dump in Belchatow open cut.

Jan 1, 2003

By J Johansson, J Lööw

There are many reports about how the new technology will affect our work, sometimes they are utopian but often dystopian. Most of the visions describe the industrial work, while the work of the managers does not seem to be affected. In this article, the authors will discuss how the new technology within the concept of Mining 4.0 changes the conditions for leadership and the work of managers in a modern mining industry.

Sep 1, 2024

By T Elms, R Beckman, M Sampson

"In today’s mining industry, the pressure of reducing costs and increasing production while maintaining high safety standards is at the forefront of operational endeavours. A combination of specific mining knowledge and technological advances has helped enable this notion. Fleet management systems have been developed to enable sites to better measure and manage production to improve operational efficiency.The integral part to managing production is having accurate, readily accessible data. This empowers key stakeholders in the management team to drive production reporting, materials tracking and budget forecasting.If a site does not run a fleet management system, manual input is heavily relied upon for production data, which introduces increased risk of human input error. Errors can drive outcomes that don’t achieve increased production at a reduced cost. Alternatively, a fleet management system can have improved accuracy but involves a high monetary investment. Such an investment is not always feasible for smaller mining operations subject to current industry cost pressures.The Emeco Operating System has been developed in alliance with sites such as the Mungari White Foil Operations by satisfying the criteria of a low intensity hardware installation, material tracking data validation processes, remote monitoring, identification of metrics to improve overall operating efficiency and providing the right information to key stakeholders.Citation:Beckman, R, Elms, T and Sampson, M, 2016. Getting Accurate Mine Information to the Right Teams to Drive Production Improvement, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 203–211 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By Dunne RC

The physical properties of an orebody require determination for virtually all mining projects, new and existing. The extent and regularity of such determinations being subject to the size and homogeneity of the orebody. Such properties have an impact at the design stage of new plants, with respect to equipment specification, and thus effects capital costs; and also impacts on the operating costs of new and existing plants, with respect to power consumption, production levels and part replacements. All of these can severely alter the bottom line and can be the determining factor in the economic viability of many projects.This paper examines some of the most common properties that are measured, the procedures utilised in determining these properties, and their variability under conditions of reproducibility, and to a lesser extent repeatability.

Jan 1, 1997

By G Partington

A regional scale prospectivity model was developed for Papua New Guinea (PNG) to identify areas of porphyry Cu-Au mineralisation. Weights of evidence modeling techniques were used to determine spatial correlations between porphyry Cu-Au mines and predictive maps created from available spatial data. These predictive maps were then combined into a final prospectivity map. Despite limited regional scale data the model has successfully identified areas of known porphyry mineralisation as prospective and has also identified areas where new mineralised systems may be discovered with further exploration. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

Passive systems for the treatment of acid mine drainage (AMD) are typically more economic in the long term than active systems. Various flow charts for treatment selection have been prepared by scientists in the USA, however, they have typically not included a variable important at New Zealand AMD sites on the West Coast: topography and available land area. Very steep topography, dense and often protected vegetation (and animals such as snails), and a high-rainfall climate result in AMD with very high flow rates in locations with very limited space for remediation. Flow charts specific to New Zealand have been prepared which accommodate topography and available land area. Parameters necessary to use the flow charts are iron and aluminium concentrations, pH, ferrous to ferric iron ratio, dissolved oxygen concentration, topography and available land area. Prior to full scale construction, is it recommended that flow rates be quantified, small-scale trials be conducted, and cost, effectiveness, limitations, and risk of failure be reviewed for various options. One full-scale remediation system has been installed in New Zealand based on this methodology and another is planned. The performance of these systems, as well as future systems to be installed, will be used to validate these treatment system flow charts.

Jan 1, 2007

By B Roache, A Vakili, R Talebi

When a highly anisotropic or weak rock mass is subjected to high-stress conditions, it can lead to large ongoing deformations or squeezing ground conditions. Squeezing ground conditions can impose increased support costs, delays associated with rehabilitation, and disruption to production schedules. Ultimately, in more severe cases, it may result in complete drive closure. Several recent case studies investigated the squeezing mechanism and measures to control squeezing ground in underground mines and also to design appropriate ground support systems. Effective management of squeezing ground conditions requires a sound understanding of the failure mechanism and the driving forces. Once the failure mechanism is understood, the appropriate ground support system should be tailored to specifically manage the critical driving forces that control the squeezing mechanism. Support type, support stiffness, reinforcement length, support density, installation times and mining sequence all have important impact on the effectiveness of the support system. This paper provides a case study at the Ballarat Gold Mine in Australia, where drive squeezing was associated with foliated ground conditions located below 700 m depth. Numerical modelling was used to better understand the failure mechanism and the driving forces that lead to squeezing conditions. The effectiveness of various support types was compared to installed ground support performance. This has provided a credible methodology for assessing and optimising the selection of reinforcement in squeezing ground conditions. CITATION:Talebi, R, Roache, B and Vakili, A, 2018. Understanding and modelling squeezing ground conditions at the Ballarat Gold Mine, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 107–118 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

The new South Australian Mining Act be came operative in July, 1972. It provides appropriate updated legislation covering pro- specting, exploration and development of mining properties. Anomalies inherent in earlier legislation which provided for the private ownership of minerals in certain areas have been overcome by the vesting of the property in. all minerals in the Crown. Appropriate transition- al and long term provisions protect the right of individuals thereby divested of their former property in minerals. In the matter of pro- specting for and quarrying of extractive minerals, the rights of landowners have been formally recognized, and the concept of rehab- ilitation of quarried areas has been introduced utilizing money provided from a royalty fund especially established for this purpose. Con- temporary company exploration practice is catered for under a new exploration tenement and at the same time the legislation makes provision for the interests of individual pro- spectors. Special provisions have been enacted to cope with the rapidly developing opal mining industry. A feature of the new Act is the introduction of legislation which recognizes enlightened contemporary thinking on the matter of environmental considerations. The Act has also extended the powers and widened the jurisdiction of the Warden's Court. In general,

Jan 1, 1974

New and more cost-effective methods of haulage and hoisting will be needed to develop the underground mines of the future. A review of the development of technology since the 1950s shows that once mechanised equipment became available it took 25 years for appropriate mining methods to be developed and the equipment made reliable, then a further 25 years to reach todayÆs level of automation and reliability. Suggestions are made about possible areas for ongoing research with the observation that there is little research worldwide into disruptive technologies. A call is made for better organisation and presentation of the opportunities and potential benefits of new underground mining technologies.

Jan 1, 2005

Aspiring to be excellent makes you a good leader as it shows a capability for strategic thought, defining and implementing a vision, making a job easier, more efficient and effective. Every great business leader can generate additional revenue or cost savings for their company. Becoming excellent requires the desire and action to follow it through. There are many established methods of excellence: benchmarking, target setting, supply chain and market analysis, employee suggestions and knowledge sharing forums. In BHP Billiton, practices benchmarking is a key tool in generating improvements for functional areas such as processing, mine operations and mine planning. Practices Benchmarking involves organisational and technical questions that allow the site to self-assess their maturity and generate a prioritised improvement path. Not only does it benchmark and identify gaps, but the approach also facilitates networking, education and team building. For new leaders it is important to remember that you are not alone. Chances are your problem has been solved before. Networks û internal, external, formal and informal can get you started and often save you time and effort. Any leader can achieve success in excellence through a proper process of problem formulation, data and analysis. Again, using key players can make the process more effective. It is important to remember that the people side of the solution is the key to success and that monitoring will ensure the solution will work. In the words of BHP BillitionÆs CEO, Chip Goodyear: Excellence is a mind set. ItÆs something that comes when people get rewarded forthinking outside the box and applying their skill and knowledge. It happens, not in$50 million chunks, but in hundred thousand and million and $2 million chunks.When you get 35 000 people thinking that way, then youÆve really got somethinggoing.

Jan 1, 2005

By G W. Wilson

Rehabilitation of tailings impoundments is one of the most challenging aspects in mine closure, as not only does the potential for producing leachate pose a challenge to the rehabilitation designer, but also other aspects such as stability and settlement must be considered. The water balance of a tailings impoundment is unique in the sense that it usually hosts a pond that in turn causes a phreatic surface in the impoundment. The position of the phreatic surface defines the saturated and unsaturated zones in the impoundment, which of course varies spatially and temporally. Predictive modelling for this hydrologic system becomes difficult, as numerical models capable of analysing the combined saturated/unsaturated zones are not adequately refined to accurately solve the flux boundary problem for infiltration at the surface of the tailings. This paper describes the development of a flux boundary model that enabled accurate modelling of the unsaturated zone in the tailings impoundment at Kidston Gold Mine, Queensland, Australia. The technique made it possible to accurately predict the spatial variation of infiltration to the tailings as a result of the presence of the phreatic table. The conceptual model defines the boundaries for the Kidston tailings dam, based on a generalised cross-section through the dam. Firstly the shape of the top boundary is described as a function of the particle size of the tailings associated with particle segregation that occurs due to the hydraulic placement of tailings. This function was rigorously tested using in situ infiltration tests and laboratory materials testing. Defining the bottom boundary of the section, ie the phreatic level was done by physically monitoring the phreatic level with 42 piezometers strategically located on the tailings dam. Analysis of this data led to the fixing of this bottom boundary through the introduction of a function that mimicked the shape of the phreatic level. The material properties of the surface layer, specifically the saturated permeability that would govern the infiltration/exfiltration rates of moisture through the top boundary layer were defined on the basis of extensive field and laboratory material testing. A function for the saturated permeability was developed on the principles of particle segregation. Finally a procedure is described for the application of the new conceptual model for the evaluation of the spatial infiltration to a tailings surface using the rigorous one dimensional surface flux boundary code SoilCover. The solution of the calculation described above was then used as the top boundary condition in conventional three dimensional saturated/ unsaturated flow codes, and verified against measured seepage rates from the tailings impoundment under drains. It was concluded that the developed spatial flux function was in deed a most rigorous representation of reality. Although the methodology presented here was applied to the Kidston tailings impoundment only, the authors believe that the principles are directly transferable to any tailings impoundment that has a varying phreatic zone thickness due to the presence of a pond. The mathematical equations describing the typical cross-section would be site specific, but the approach and ultimate solution methodology would be directly transferable.

Jan 1, 2003

Tin mining has taken place in the New England region of New South Wales since 1872. Until fairly recent times there was little pro- vision made for environmental protection. Mining methods,which included ground sluicing and open cutting,had considerable environmental impact. Much of the topsoil was lost and there is little vegetation on the infertile and at times toxic, subsoil. Thus much of the lands disturbed by mining have not been stabilised and are eroding, causing extensive pollution of adjacent watercourses. There are more than 1500ha of abandoned tin mine sites in the New England, representing one of the worst rehabilitation problems in New South Wales and reflecting poorly on the mining industry as a whole. Recent tin mining operations incorporate progressive rehabilitation in their mining cycle. Topsoil is stockpiled and later respread. This topsoil contains a seed source, facilitating revegetation and thus stabilisation. The tin mining industry, under considerable cost pressures at present, is seeking a cost- effective revegetation technique. Most of the mines in the New England are situated in a forest environment. Trials have been conducted in the past using exotic pasture species with limited success due to the characteristics of the subsoil. Other revege- tation trials have used pine or eucalypt tree species. The cost of these techniques is a major disadvantage. Certain acacias species were observed colonising disturbed tin mining areas on very infertile subsoils. Acacias have a number of characteristics indicating a possible applic- ations in mine rehabilitation programmes.

Jan 1, 1987

Development of a New Dry Density Separator for Fine-Grained Materials

Sep 13, 2010

The classic description of Project Finance as "the reliance by lenders on the cashflow of a project, supported by the assets of the project with no recourse to the project sponsor's corporate balance sheet" has, like most other terms in the finance industry, evolved through recent usage. The area now under most scrutiny is the sharing of risks between parties either most able to take them or prepared to accept payment for them. Creativity in, and flexibility of financing structures have enabled project lending to continue under a dramatically different economic outlook. The diminishing competitiveness of the Australian producers in a global market place of uncertain commodity prices has discouraged the advancement of many large scale resource projects. The majority of new project financings has been designed to assist the relatively small company promote and develop its first projects. New trends- are emerging in four areas: sources of capital; borrowing structure; financing instruments (securitisation); and risk underpinning. As project financing becomes more widely used, the range of interested financiers grows. New initiatives contribute to its development and evolution with a view to increase effectiveness to the sponsor of any new venture.

Jan 1, 1987

The present practices in electro-refining of copper are shown to be the result of piecemeal and gradual improvements and innovations as metallurgists responded to changing cost pressures and the availability of new technology.Major changes were inhibited by capital cost restraints and a reluctance to build unproven ideas into new plants.It is suggested that the level of technology available today, combined with the greatest cost pressures the industry has known, call for fundamental re-appraisal and a questioning of widely accepted conventional practices.Examples of the industry reaction to changing pressures are given, and directions for future developments are suggested.

Jan 1, 1985

By Floyd JM

Conventional smelting reactor systems were designed to recover only one main element from their feedstocks. They did not possess sufficient flexibility to allow optimisation of co-production of multiple values from a complex feed.New reactors such as Sirosmelt and Top Blown Rotary Converters are providing new possibilities for making separation between components and this is of great significance for the complex feeds which are becoming prevalent in the metal extraction industry.Process routes using chemical procedures which take advantage of the flexibility of these reactors will be discussed in relation to a number of possible feedstocks.

Jan 1, 1985

In September 1980 the N.S.W. Environ- mental Planning and Assessment Act was gazetted. This legislation created a new arena of government involvement in the procedure for obtaining approval to open a new mine, or expand an existing mine in N.S.W. Since 1980 the legislation relating to environmental protection requirements, the procedure for obtaining Development Consent and the nature of relevant government policies have caused considerable confusion on the part of many potential developers. Implementation of the legislation has now become systematic and relatively predictable. However, certain aspects can be improved and require urgent government action.

Jan 1, 1983