Search Documents

WINDING engines are one of the most important units in the equipment of a mine. Upon the winding machinery depends not only the output of the mine, but it supplies in most cases the only means by which workmen enter and return from the mine, and consequently the utmost care and attention is desirable in its design. The efficiency of a direct acting winding engine, as a machine is very low. In other words, the proportion between the useful work performed and the actual work the engine is capable of performing (under the most favourable conditions) is very small. The reasons for this are:-1. The intermittent nature of the work; the engine is stopped from 20 to 25 %(or even more) of the time which would constitute a useful day's work.2. The large amount of power that is absorbed applying the brakes to bring the load to rest.3. That the net useful load raised is small in comparison with dead load to be lifted, and the parts to be set in motion.4. That, owing to the frequent stops, initial condensation in the cylinders is always greater than in a continuously running engine, whilst radiation from steam pipes, valve chests, &c., goes on whether the engine is running or...

Jan 1, 1911

A mechanised sub-level overhead benching method is used at Cleveland, to produce 22,000 tons per month of ore assaying 0.92% Sn and 0.40% Cu. The ore occurs in a series of vertical lenses which can be mined by open stoping. Levels are developed at 60ft., vertical intervals by jumbos. The ore is silled out and the stope block formed between levels drilled out by long hole drilling. Each row of holes is fired and broken ore within safe reach from the stope brow is mucked out by Wagner ST-5A Scoop Trams. The remaining broken ore is recovered on extraction of the next lower level. Ore is hauled by road to the crusher station from the mine. As mining proceeds below the lowest surface portal a spiral decline will be used for ore haulage and mine servicing.

Jan 1, 1970

By Nairin J. D, Hayes P. C

Detailed studies of the microstructures and compositions of zinc and lead blast furnace sinters have been undertaken. An analysis of the results obtained has indicated that in many cases the microstructures of these complex materials can be explained by the solidification of melts from pseudo-ternary phase systems. Further laboratory studies have been carried out to more accurately determine the extent of primary phase fields and the liquidus temperatures in the appropriate binary and ternary systems. This approach shows considerable promise in simplifying the descriptions of slag systems used in oxidising and reduction smelting processes for lead and zinc recovery.

Jan 1, 1992

General Gold was discovered in quartz veins at Wiluna in 1896, and the first lode was discovered in 1904. Since 1896, some 2.5 million ounces of gold have been produced from the Wiluna area. The mining operations at Wiluna are 100 per cent owned by Wiluna Gold Pty Ltd, a wholly owned subsidiary of Wiluna Mines Ltd. Oxide and sulphide gold ore is extracted by conventional open pit mining techniques, and ran-of-mine ore is processed through two separate circuits. The oxide circuit has a capacity to treat 600 0(X) tonnes per annum and the sulphide circuit has a capacity to treat 400 (XX) tonnes per annum. Additional gold is won by dump leaching sub-grade oxidised ore and by retreating of primary ore flotation tailings from previous operations. Testwork carried out in 1990 indicated the viability of leaching dumps of run-of-mine oxide ore, and in June 1991 Signet Engineering of Perth, WA, was awarded an EPCM contract to construct a nominal 2.5 million tonne dump leach facility, for a total construction estimate of 51.75 million.

Jan 1, 1994

By Armstrong M, Kleingeld W. J

Current low prices for many metals mean that deposits have to be mined at high cut-offs (relative to their mean grade), which means that only a small percentage of mining blocks are above cut-off. Worse, at such high cut-offs, the blocks above cut-off are usually not grouped into convenient clumps for mining; they tend to be split into small isolated patches that are difficult to reach and hence expensive to extract. Companies wishing to acquire mineral properties have to be able to work out quickly what percentage of blocks are above cut-off and what can effectively be mined given the mining method envisaged. Moreover they need this information within a relatively short-time. The work presented here relates to typical South African gold mines (ie tabular orebodies) but the long-term objective is to develop tools for quantifying the impact of reserve breakup at high cut-offs for a wide range of underground mines including those that are not tabular. The mining method and the sampling procedure determine whether ore blocks can effectively be located and extracted economically. This project studied the impact of these two factors on the recoverable reserves for Witwatersrand gold mines. In order to be repeatable, the tests were done on numerical models of the deposit obtained by geostatistical simulations. To ensure realism, the orebody model and the mining scenarios were based on a specific mine. The recoverable reserves (ore tonnage above cut-off, the corresponding metal quantity and the average grade) were calculated for a wide range of cut-offs for four mining scenarios, as well as for the base case of free selection: ò Scenario 1: Blocks are taken if their true grade is above cut-off and if they are accessible from a raiseline (no information effect, no marginal blocks). ò Scenario 2: In addition to the accessible pay blocks, adjoining marginal blocks are taken (no information effect, + marginal blocks). ò Scenario 3: Blocks are taken if their estimated grade is above cut-off and if they are accessible from a raiseline. Here the estimator is the average of the face samples (information effect, no marginal blocks): ò Scenario 4: Accessible pay blocks are taken if their estimated grade is above cut-off. Adjoining marginal blocksare also taken (information effect, + marginal blocks). ò Free selection: All blocks whose true grade is above cut-off are taken irrespective of their accessibility. The results can be presented in different ways, for example by plotting ore tonnage above cut-off versus cut-off grade, or metal tonnage above cut-off versus cut-off grade etc. As expected, this shows the hierarchy between the five scenarios from the free selection base case to scenario No 2 (true accumulations, pay +

Jan 1, 1995

By Peck J. P, Kennedy D

Drill performance monitoring studies were recently completed at the Fording River mine, British Columbia. Microprocessor-based instrumen- tation and data analysis techniques were developed with the objective to improve short and long term mine planning. Data analysis permitted the identification of thicknesses and interfaces between soft/hard zones at depth based upon the recorded responses of the drill. Data clearly con- trast the soft coal seams and harder waste rock units based on variations in recorded drill rotary speed and torque, hydraulic downpressure, bail- ing air pressure and instantaneous rate of penetration. These parameters were monitored and recorded at 10 cm sampling intervals. Processed drill data was correlated with gamma logs, an existing means for locating coal seams and distinguishing between waste units. Current development of a pattern recognition module aims towards automated interpretation of drill data, identifying micro-and macro-geological and geomechanical rock mass characteristics. Delay between acquiring, processing and interpret- ing the drill data for practical use by mine personnel should be minimized. Integration of this technology with the mine's current main-frame based Mine Engineering Application System software will enable more accurate and timely annlication of the nrocessed drill data.

Jan 1, 1989

There is no other effective way for study ing firedamp and coaldust explosions than to produce controlled explosions in a pre-monitor- ed environment - either mine openings kept for the purpose, or special surface galleries. Such explosion testing facilities have been employed historically at Buxton in U.K., with lesser known installations at Bruceton, U.S.A., Tremonia, West Germany, Katowice-Mikolow, Poland and elsewhere. Both firedamp and coal dust explosions are studied. Normally coal dust explosions are initiated by somewhat standardised methane air mixtures, by explosives, or purely by coal dust. Various structures and suppression installations are installed in roadways and galleries prior to explosion to simulate destruction and suppression, and the results of such tests form the basis of suppression installations, especially stone dust barriers and water barriers. Other data collected from these experiments include rev- ersals of explosion waves, pressures and temperatures and duration of explosion waves, analyses of aftergases etc. Other uses of explosion testing galleries include testing of explosives, electrical equipment and frictional . sparking.

Jan 1, 1981

By S S. Kanchibotla, D La Rosa, R W. Pesch

The Porgera Joint Venture and Dyno Nobel have commissioned a joint project to optimise the drill and blast operations to increase the overall profitability of the mine. One of the aims of this project is to increase the throughput of semi autogenous (SAG) mills by optimising the blast fragmentation. A number of test blasts were conducted during the period May 2000 to January 2002 and the ore from these blasts was campaigned through the mill. The data from these trials suggested up to 15 per cent increase in the SAG mill throughput with high energy blast designs. However, changes in ore geology (shape, structure and hardness) and potential ore dilution/loss and wall damage have raised concerns about the economic benefits of these designs over the entire orebody. The lack of a system to track the economic benefits of these modified designs has also compounded these concerns. PJV and DynoConsult, the consulting arm of Dyno Nobel have initiated steps to minimise the potential for ore dilution and wall damage resulting from these modified designs. DynoConsult worked with Julius Kruttschnitt Mineral Research Centre (JKMRC) to develop and implement a blast management system to track the quality of blast implementation and down stream process benefits. This paper discusses the implementation of the system and the results achieved to date.

Jan 1, 2003

By Culshaw MG, Deaves AP, Bell FG

The accurate prediction both of the water ingress into sub-surface excavations and the nearby groundwater pressures is of fundamental importance to the control of the stability and flooding of tunnels or mines constructed below the water table. Predic- tions are usually based on laboratory and in situ permeability determinations together with observations of groundwater conditions in boreholes. Although established theoretical methods provide a basis for prediction, the actual ingress depends on many factors. The objective of this paper is to explore the geological controls on groundwater conditions, and the available methods of prediction of both groundwater flow and pressure are outlined. Salient points are emphasised by reference to a case history involving the construc- tion of a tunnel in a faulted and mixed sequence of sandstones, siltstones, shales and coals. Water ingress quantities have been monitored for a variety geological and geotechnical conditions including heavily faulted and mine disturbed ground. The overall results are discussed with reference to the relevant hydrological and geologi- cal conditions in terms of the geological structure, lithology and rockmass condition as well as the construction methods.

Jan 1, 1988

By A B. Richards

Effective control of blast vibration and flyrock requires that significant factors be identified and quantified, that the blast be designed to ensure both blasting efficiency and compliance with applicable limits, and that the blast design be effectively implemented by field personnel. Significant factors contributing to ground vibration and airblast are: charge mass; distance and direction relative to the blast; drilling design: burden, spacing; stemming height and material type; hole diameter and depth; and initiation sequence and direction.In addition, airblast may be strongly influenced by shielding and meteorological conditions. Ground vibration is also influenced by the transmission characteristics of the ground and soil. Flyrock throw is determined by charge mass, burden, stemming height, blasthole diameter and depth. The contribution of each of the factors has been quantified and models developed to enable the environmental outcomes of blast design to be predicted. Environmental blast design is necessary to ensure compliance with regulatory limits and the implementation of æsafeÆ exclusion zones for flyrock clearance. This paper discusses the models used for environmental blast design and demonstrates the often significant effects that lapse during implementation of the design can have on predicted outcomes. In practice, drillers and shotfirers are sometimes confronted with situations that require modifications to the blast design to cope with the real site situation. Methods are presented that may be used by drillers and shotfirers to evaluate the effect of these modifications, the tolerances that must be reached during their work practice and checking procedures, and the consequences of their actions.

Jan 1, 2004

By Parsons A. E

The application of known pelletizing tech- nology was successful in the agglomeration of zinc concentrate into pellets of minus 6mm siz- ing using fine zinc calcine and sulphuric acid as binder. Subsequent roasting trials conducted in a 0.3 m diameter fluid bed reactor, showed that the pellets satisfactorily withstood hot physical abrasion during fluidization. Fines generation was low and the pellet calcine was hard, possessing excellent handling properties. Results of laboratory scale static pellet sinter- ing tests showed conclusively that the deterior- ation in sinter physical quality experienced with fine calcine was not apparent when the calcine was added to the mix in pellet form. Based on the results of small scale exper- imental work, a one tonne per hour pilot plant was constructed and operated. Several thousand tonne of pellets were produced-for fluid bed roasting in Badische Analin and Soda Fabrik (B.A.S.F.) turbulent layer (T.L.) roasters previously designed for roasting iron pyrite concentrate. Continuity of the T.L. fluid bed roasting operations was achieved when the waste heat boilers were replaced with atmospheric coolers and thus eliminated the problems of gas flow restrictions. Sinter plant trials were conducted over a period of two weeks with the addition of pellet calcine to the sinter feed. Results showed a marked improvement in sinter plant performance, and as a result of better bed permeability, increased sinter production was achieved, with- out significant deterioration in sinter quality.

Jan 1, 1974

This paper outlines the manner in which legislative control for tunnelling and allied operations has evolved, detailing Victorian experience. It examines the concept of mine managers as it relates to the industry and attemps to illustrate its benefits. The Victorian experience in relation to fatal and serious accidents is examined in detail, particularly in the allied art of trenching and examines the Krings system of trench lining support which is hoped will catalyse an increase of engineering expertise in this area. The paper concludes by demonstrating that safety awareness is not incompatible with production efficiency or economic viability.

Jan 1, 1981

INDEX OF CONTENTS.1. Historical.2. Manufacture.3. Heat Treatment.4. Fatigue, Failures.5. Consideration of the Establishment o£ a Central Testing or Proving Station.HISTORICAL.Since the introduction of improved high air pressure drilling machines in the early part of the century, efforts have been made to develop the quality of the rock drill bit, in order to take advantage of the greater increase of power output per unit weight of the machines (1). This resulted in the change from solid to hollow steel in the second decade of the present century (2).As the greatest sufferers from the dread disease of silicosis (3), it seemed appropriate that the South African gold mines should be the first to use hollow drill steel. Since then solid drills have become practically obsolete for mining purposes.Water is used with hollow steel drills not only to keep the cutting end cool, but also to assist in preventing the formation of undue dust during drilling. It is of interest to note, however, that water fed through hollow steel or sprayed into the air is only partially effective in removing fine dust particles a few microns in diameter, which particles are said to be the most potent in producing silicosis (3a).So far as the composition of "straight" carbon steel drills is concerned, a commission appointed by the Johannesburg mines carried out a very exhaustive series of tests on drill steels.These drills were manufactured from steel made by all the standard methods, including Swedish, Bessemer, crucible, openhearth, and, to a limited extent, electric furnace steel. It should be remembered that the commissioners' report was issued in 1913, when hollow drill steel had not yet been introduced. Only solid steel drills were then in use.

Jan 1, 1947

By Mousset-Jones P, McPherson M. J

Underground airways are characterized by irregular shape and uneven surfaces including large-scale natural roughness, fractures, and a super-imposed sand roughness. Swirls in the grooves of the wall and separation because of the periodic variation of the open cross sec- tion, due to the blasting patterns, make it almost impossible to calculate average con- vective heat transfer computationally on the bases of the geometrical description of the surface. However, dimensionless friction factors can be used to characterize the surface effect of an airway and an analogy between heat and momentum transfer can be applied to calcu- late an average convective heat transfer Coefficient.

Jan 1, 1988

The LeadtZinc Concentrator at Mount lsa treats all the lead-zinc-silver ore from the Mount Isa Mine and some of the ore from the Hilton Mine. This concentrator was commissioned in June 1966 and total lead-zinc-silver ore treatment was transferred from the Mount rsa's original No 1 Concentrator in May 1967. Plant capacity is around 5 x 106 t/y.There have been three phases of major plant modifications since commissioning:1. replacement and upgrading of the flotation section in 1979; 2. upgrading of the crushing plant and installation of a heavy medium hydrocyclone plant in 1983 for ore preconcentration, and; 3. doubling ball milling capacity and a further upgrading of the flotation section in 1992.Other developments have included the installation of flotation columns and Jameson cells.The evolution of milling practice since 1955 has been reported by Davey and Slaughter (1970), Bartrum, Dobrowolski and Schache (1977), Fiedler and Munro (1984) and Espinosa-Gomez el al (1989).Lead concentrate is smelted in Mount Isa while zinc concentrate and bulk concentrate (locally called Low Grade Middlings or LGM) are railed to Townsville and shipped to custom electrolytic zinc plants and ISP smelters.

Jan 1, 1993

By Seymour C. A

Peak Downs Mine, a five million tonnes a year coking coal operation, strip mines a, series of Permian coal seams. Seam thickness ranges from 0.5m to 5.0m, and seams consist of multiple coal plies with intermediate shale and mudstone partings. Four 47m3 draglines strip overburden to a cover depth of up to 60m. Coal loading is by 12m3 shovels and 14m3 to 18m3 front-end loaders. Parting removal takes place where the layer of shale and mudstone between seams exceeds 0.3m in thickness. Parting has been removed by a wide variety of earthmoving equipment in order to evaluate the problem and to select the optimum method from an operational and economic standpoint. Multi-seam stripping of the thicker seams is accomplished by working draglines from spoil- pile benches. Coal seams thinner than lm are recovered by dragline and stacked in the pit for later loading.

Jan 1, 1974

The late 1960's and 1970's saw the initial development of the coal resources of the Bowen Basin of Queensland. The projects developed relied on large scale, open-cut operations using draglines for overburden removal and, in the majority of cases, project viability could be established based solely on those open-cut operations. Many of the mines developed in the 1980's have the same characteristics.Unlike these mines, the German Creek Mine has limited open-cut reserves at low overburden to coal ratios, and planning of the complex involved a large open-cut mine capable of developing early cash flow, with phased introduction of underground mining to replace open-cut capacity as the strip ratio increased.

Jan 1, 1985

Design of cemented fill in mining is often carried out without any consideration of the structure of the fill. The composition of cemented fills varies in the stopes due to the placement method, and the strength of the fill in the laboratory depends on the density, orient- ation, moisture content and drainage conditions. Within each stope there are definite zones and the structure of both cemented rockfill and cemented hydraulic fill has to be defined for each zone and the field conditions simulated in the laboratory. Structure also affects fill permeability and compressibility. From a study of the cemented fill in place, the effect of changes in the placement methods can be seen and then controlled to improve fill performance and economy. These features of cemented hydraulic fill and cemented rockfill behaviour are discus- sed and illustrated through reference to field and laboratory work undertaken at Mount Isa.

Jan 1, 1973

The basic flowsheet for the Kalgoorlie Nickel Smelter and Kwinana Nickel Refinery are discussed in relation to the mineral components of Kambalda produced nickel concentrates. Both processes handle violarite and pentlandite satisfactorily but the smelter has limitations where high copper recovery is required and in its ability to handle magnesia containing minerals. While the latter can be more economically handled at Kwinana the limitations of this tolerance are discussed together with problems arising from treating pyrrhotite, pyrite and precious metals by the Sherritt Gordon process.

Jan 1, 1973

By Arit I, Adisoma G

General Limit Equilibrium Method (GLE) and Janbu's Generalised Procedure of Slices (GPS) are two limit equilibrium methods in slope stability analysis which satisfy all equilibrium conditions. Numerical difficulties associated with these metho

Jan 1, 1998